Car Subwoofers (324)

Alpine SWT-10S4 1000W Peak 10" SWT Series Single 4-ohm Shallow Mount Subwoofer Right size, Right sound. Here's a big bass breakthrough for truck lovers. Alpine engineered their SWT-10S4 10" subwoofer to go behind your seat and sound especially good in the limited space of a truck cab. This deep-sounding, high-performance sub works well in shallow enclosures that'll fit behind or under the seat in your truck. A "high amplitude" surround allows more cone travel than a regular sub, so the SWT-10S4 can push more air and play louder. Airflow-insured subs get hot as they play, and the heat usually gets vented away via a port in the back of the sub's pole piece. Alpine recessed the pole port and added cooling air vents on the sides of the frame, allowing you to use an enclosure with an inside clearance of as little as 4-3/16" without blocking critical airflow. General Features: 10" SWT Series Single 4-ohm Shallow Mount Truck Subwoofer Peak Power Handling: 1,000 watts RMS Power Handling: 350 watts Recommended Power Range: 100W - 350W Poly-Mica Dust Cap & Pulp-Kevlar Polyurethane Foam Surround H.A.M.R. Surround Technology Spiral Cut Aluminum Former 65mm Voice Coil with High-Temp 4-Layer SVC Winding 8AWG Push Terminals Top-mount depth: 4-3/16" Mounting Diameter: 8-15/16'' Frequency Response: 30 - 200 Hz Sensitivity: 84.8 dB Authorized Dealer 1-year Manufacturer's Warranty What is in the SWT-10S4 package: SWT-10S4 owner's manual 10" Thin-mount subwoofer Online product registration information Warranty information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine R-SB10V Pre-Loaded R-Series 10-inch Subwoofer Enclosure Enclosure Stacking Features Unique to Alpine, the subwoofer 10-inch and 12-inch enclosures are available in a single or “linked” format with an optional mounting bracket. This innovative design allows the sound consumer the option to easily add more bass to their system. The optional mounting bracket (sold separately) is available in a 10-inch KTX-H10 or 12-inch KTX-H12 solution that mounts to the face of the subwoofer and links for a sturdy, dual-subwoofer enclosure. The silver enclosure trim matches the steel bracketing and Halo display trim for a synergized look. Optimized Performance The ported enclosure design delivers a higher total sound output for deep, powerful bass, reliable sound reproduction, and overall great sound quality. The 10-inch enclosure is tuned to 36 Hz while the 12-inch enclosure is tuned to 35 Hz for optimized performance with Alpine’s S-and-R-Series subwoofers. General Features: Includes R-W10D4 wired in parallel 750W RMS power handling 2Ω Impedance Ported enclosure design Frequency response: 26-200 Hz Vented enclosure tuning frequency: 36 Hz Dimensions 16-inch W x 12.6825-inch H x 14.5-inch D Authorized Dealer 1-year Warranty ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine W12S4 12" BassLine Series 12" 750W Max (250W RMS) 4-ohm Bass Subwoofer Legendary Alpine quality at an affordable priceCar audio enthusiasts know that Alpine is the leader in technology and innovation. Their reputation for developing the most reliable products is legendary. The BassLine product line is their quest to give customers a quality product that won't break the bank.The surround and wattage match made in heaven.The 250 watts of continuous power that the W12S4 handles complements the poly-foam surround that Alpine went with. It provides the best sound quality money can buy at this price point.General Features: 12-inch single 4Ω subwoofer Polypropylene and mica cone with poly-foam surround Peak Power Handling: 750 watts RMS Power Handling: 250 watts Recommended power range: 50W - 250W RMS Polypropylene-Mica cone High-excursion poly-foam surround Progressive Wavelit Ribs (P.W.R.) cone design Frequency Response: 32Hz-200Hz 5-5/16-inch mounting depth Recommended Sealed box volume: 1.09 Cu. Ft. Recommended Ported box volume: 1.91 Cu. ft Bass For All High-strength custom steel frame 8AWG push terminals 2" voice coil 52oz. magnet Recommended Box Volume: 0.5-1.5 Cu. ft.3 Top-mount depth: 5-5/16" Cutout diameter: 10-5/8" Frequency Response: 22 - 200Hz Sensitivity: 87.9dB Resonance Frequency (Fs): 30 Performance: Efficiency & Tight Bass An optimized magnet circuit allows more focused magnetism in the gap, improving efficiency. This means tighter bass control and more output! What's in the W12S4 package: One 12" Subwoofer Adhesive-backed foam gasket Application Guide Online product registration information Warranty information Important Notice! W12S4 owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine S-W8D4 900W Max (300W RMS) 8" Type S Series Dual 4 Ohm Car Subwoofer ADD BASS TO PRACTICALLY ANY VEHICLE Don’t think you have room for a subwoofer? Think again. The new S-W8D2 and S-W8D4 8” S-Series subwoofers have a shallow mounting depth of just 3-3/4” and can be used in a sealed box enclosure as small as .15 cubic feet. It is perfect for under-seats, behind rear bench seats in trucks, or even in some door applications. General Features: 8" 4 Ohm Type S Series Subwoofer Power Handling: Peak: 900 watts RMS: 300 watts Recommended Power Range: 150 - 300 Watts Kevlar Reinforced Pulp Cone HAMR Santoprene Rubber Surround Progressive Spider with Reinforced Layer Tinsel Leads Compound Radius Curve Extended Pole Geometry Perimeter Vented Frame with Airflow Management System 10 AWG Push Terminals 35mm Underhung Voice Coils Concealed Mount Gasket 34oz Ferrite Magnet Top-mount depth: 3-3/4" Cutout diameter: 6-7/8" Frequency Response: 34-200Hz Authorized Dealer 1-year Manufacturer's Warranty Priced Individually What's in the S-W8D4 package: 8" Dual 4-ohm voice coil subwoofer Alpine S-W8D4 owner's manual 1 Rubber concealing ring Two 3" jumper cables Subwoofer Application Guide Online product registration information Warranty information  Important Notice!  ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine W10S4 10" Bass Subwoofer 750W Max (250W RMS) 10" BassLine Series Single 4 ohm Car Subwoofer Legendary Alpine quality at an affordable priceCar audio enthusiasts know that Alpine is the leader in technology and innovation. Their reputation for developing the most reliable products is legendary. The BassLine product line is their quest to give customers a quality product that won't break the bank.The surround and wattage match made in heaven.The 250 watts of continuous power that the W10S4 handles complements the poly-foam surround that Alpine went with. It provides the best sound quality money can buy at this price point.General Features: 10" Single 4-ohm BassLine (Bass) Series Subwoofer Power Handling: Peak: 750 watts RMS: 250 watts Recommended power range: 50W - 250W RMS Polypropylene-Mica cone High-excursion poly-foam surround Progressive Wavelet Ribs (P.W.R.) cone design An optional Alpine KTE-10PG subwoofer grill is available and is a wonderful complement to the trim ring with the Alpine logo High-strength custom steel frame 8AWG push terminals 2" voice coil 52oz. magnet Top-mount depth: 5-1/16" Cutout diameter: 9" Frequency Response: 24 - 200Hz Sensitivity: 86.6dB Resonance Frequency (Fs): 32 Authorized Dealer 1-year Manufacturer's Warranty What's in the  W10S4 package: W10S4 owner's manual One 10" Subwoofer per box Adhesive-backed foam gasket Application Guide Online product registration information Warranty Information Important Notice! Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine S-W12D4 1800W Max (600W RMS) 12" Type-S Series Dual 4 Ohm Car Subwoofer VERSATILE APPLICATIONS Along with the new 8” woofer, the 10” and 12” S-Series subwoofers have been re-designed from the ground up. The mounting depth of the 10” and 12” subwoofers are almost 1” more shallow than previous models at just over 4.5” for the 10” models and just over 5” for the 12” models, allowing them to fit into a wide variety of installation applications. General Features: 12" 4 Ohm Type-S Series Subwoofer Power Handling: Peak: 1800 watts RMS: 600 watts Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 5-1/16" Cutout diameter: 10-9" Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 31 Hz Authorized Dealer 1-year Manufacturer's Warranty What is in the S-W12D4 package: Alpine S-W12D4 owners manual One 12" Dual 4-ohm voice coil subwoofer Two 3" jumper cables Subwoofer Application Guide Online product registration information Warranty Information ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine S-W10D2 1800W Max (600W RMS) 10" S-Series Dual 2 Ohm Car Subwoofer Alpine introduces the all-new S-Series Subwoofers; their unique design substantially improves bass output and provides installation versatility. Each S-Series subwoofer uses a custom-stamped steel frame and is available in twelve, ten, and eight-inch. These high-strength frames were designed to withstand the rigors of the improved S-Series motor. They have frame leg vents, a vented back plate to help cool the subwoofer voice coil and motor parts, and a shallow design to help fit in smaller spaces. The S-Series Subwoofers incorporate two strontium ferrite magnets stacked together, providing increased motor strength and excursion, ultimately delivering an accurate bass to your music. The convenient push-type insert terminals with a dual voice coil jumper system will significantly reduce installation time. Just strip the speaker insulation at the wire end, then insert the bare wire into the hole of the spring-loaded push terminal. At the same time, the concealed mount gasket system creates a clean, finished appearance for any vehicle. General Features: 10" 2 ohm S-Series (Type-S) Subwoofer RMS Power Handling: 600 watts Peak Power Handling: 1800 watts  Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 4-11/16" Cutout diameter: 8-13/16 Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 33 Hz Authorized Dealer 1-year Manufacturer's Warranty What is in the S-W10D2 package: S-W10D2 owner's manual One 10" Dual 2-ohm voice coil subwoofer 1 Rubber concealing ring Two 3" jumper cables (each has a single banana connector on each end) Subwoofer Application Guide Online product registration information Warranty Information ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine R-Series next generation R2-W10D4 10" 4 Ohm 2250 Max, 750W RMS DVC Car Audio Subwoofer The new 2022 R-Series subwoofers are here - drawing from decades of Subwoofer engineering experience. They deliver deep, clean, accurate bass and feature Alpine’s HAMR Surround for maximum cone excursion, delivering tons of bass output. The new ceramic dust cap is lightweight and rigid, keeping distortion at an absolute minimum. The enlarged motor structure ensures better woofer control for a strong, clean bass response. General Features: 10" Dual 4 ohms Type-R Series Series Subwoofer RMS Power Handling: 750 watts Peak Power Handling: 2250 watts Kevlar Reinforced Pulp Paper Cone High-Amplitude Multi-Roll (H.A.M.R) Surround Push-Type Speaker Terminals (Up To 8AWG Wire Size) Oversized Dust Cap 2.6" High-Temperature Voice coil 20 mm Xmax 123 oz. Double Stacked Ferrite magnet motor structure Frequency Response: 26 - 200 Hz Resonance Frequency (Fs): 32 Hz Sensitivity: 82.8 dB Sealed box volume: .4 cubic feet - .85 cubic feet Ported box volume: .75 cubic feet - 1.3 cubic feet Top-mount depth: 6" Cutout diameter: 9.6" CTA-2031 Compliant: Yes Authorized Internet Dealer Alpine KTE-10G Optional Protective subwoofer grille 1-year Manufacturer's Warranty What is in the R2-W10D4 package: R2-W10D4 owner's manual One 10" Dual 4-ohm voice coil subwoofer Plastic trim ring Two 4.5" jumper wires Application guide Online product registration information Warranty Information  Important Notice  ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine R2-W12D2 2250W Max (750W RMS) 12" R-Series Dual 2-Ohm Car Subwoofer The new 2022 R-Series subwoofers are here - drawing from decades of Subwoofer engineering experience. They deliver deep, clean, accurate bass and feature Alpine’s HAMR Surround for maximum cone excursion, delivering tons of bass output. The new ceramic dust cap is very lightweight and rigid, keeping distortion an absolute minimum. The enlarged motor structure ensures better overall woofer control for a clean, strong bass response. General Features: 12" Dual 2 ohm Type-R Subwoofer Peak Power Handling: 2250watts RMS Power Handling: 750 watts Recommended power range: 300 - 750W RMS CTA-2031 compliant power ratings Parabolic pulp/kevlar cone H.A.M.R. surround Polypropylene, mica, and talc dust cap Reinforced cone neck and spider joint Cast aluminum frame with integral shorting sleeve 8AWG push terminals with VC configuration jumpers 2.6" High excursion overhung voice coil 127 oz. Strontium ferrite segmented magnet Top-mount depth: 6-3/8" Cutout diameter: 10-7/8" Frequency Response: 24 - 200Hz Sensitivity: 84.3dB Resonance Frequency (Fs): 27Hz Authorized Dealer 1-year Manufacturer's Warranty What's in the R2-W12D2 package: R2-W12D2 owner's manual One 12" Dual 2-ohm voice coil subwoofer Two 3" jumper cables R-Series Subwoofer Application Guide Online product registration information Warranty Information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine R2-W12D4 2250W Max (750W RMS) 12" R-Series Dual 4-Ohm Car Subwoofer The new 2022 R-Series subwoofers are here - drawing from decades of Subwoofer engineering experience. They deliver deep, clean, accurate bass and feature Alpine’s HAMR Surround for maximum cone excursion, delivering tons of bass output. The new ceramic dust cap is lightweight and rigid, keeping distortion at an absolute minimum. The enlarged motor structure ensures better woofer control for a strong, clean bass response. General Features: 12" Dual 4 ohm Type-R Subwoofer Peak Power Handling: 2250watts RMS Power Handling: 750 watts Recommended power range: 300 - 750W RMS CTA-2031 compliant power ratings Parabolic pulp/kevlar cone H.A.M.R. surround Polypropylene, mica, and talc dust cap Reinforced cone neck and spider joint Cast aluminum frame with integral shorting sleeve 8AWG push terminals with VC configuration jumpers 2.6" High excursion overhung voice coil 127 oz. Strontium ferrite segmented magnet Top-mount depth: 6-3/8" Cutout diameter: 10-7/8" Frequency Response: 24 - 200Hz Sensitivity: 84.3dB Resonance Frequency (Fs): 27Hz Authorized Dealer 1-year Manufacturer's Warranty What's in the R2-W12D4 package: R2-W12D2 owner's manual One 12" Dual 4-ohm voice coil subwoofer Two 3" jumper cables R-Series Subwoofer Application Guide Online product registration information Warranty Information https://www.youtube.com/watch?v=ihjWBSOYVxE&t=179s ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

2 Alpine S-W12D4 1800W Max (600W RMS) 12" Type-S Series Dual 4 Ohm Car Subwoofer VERSATILE APPLICATIONS Along with the new 8” woofer, the 10” and 12” S-Series subwoofers have been re-designed from the ground up. The mounting depth of the 10” and 12” subwoofers are almost 1” more shallow than previous models at just over 4.5” for the 10” models and just over 5” for the 12” models, allowing them to fit into a wide variety of installation applications. General Features: 12" 4 Ohm Type-S Series Subwoofer Power Handling: Peak: 1800 watts RMS: 600 watts Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 5-1/16" Cutout diameter: 10-9" Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 31 Hz Authorized Dealer 1-year Manufacturer's Warranty What is in the S-W12D4 package: Alpine S-W12D4 owners manual One 12" Dual 4-ohm voice coil subwoofer Two 3" jumper cables Subwoofer Application Guide Online product registration information Warranty Information ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Cerwin Vega Mobile H7SE10 Audio Control LC2iB and Amp KIT4 gauge package Audio Control LC2i 2 Channel Line Out Converter Accubass and Subwoofer Control for amps to your factory system The LC2i is a compact, two-channel processor with active input circuitry. It can accept speaker-level signals of up to 400 watts per channel from factory-installed source units or amplifiers and convert them to high-quality pre-amp signals that can be directed to after-market processors and amplifiers. Users can enjoy maximum sound quality while maintaining factory volume and steering wheel controls. General Features: Two channels of active speaker level inputs - Accepts 400-watt signals per channel. AccuBASS processing for correction of bass roll-off Fixed and variable outputs with discrete level controls GTO - Signal sensing inputs The 12-Volt trigger that will turn on LC2i Dual amplifier 9.5-volt pre-amp outs Level matching controls 12 Volt trigger output Input for optional subwoofer level control: AudioControl ACR-1 Dimensions: 6-3/8"W x 3-1/8"D x 1-1/2"H Authorized Internet Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) Maximum speaker level input: 400 watts per channel Maximum Preamp Output: 9.5Vrms / 13V peak Optional Dash Level Control Remote: +0dB / -19dB Frequency response: 10 Hz - 100,000 Hz; ±1dB Total harmonic distortion: 0.01% Signal to Noise ratio: >110dB Input Impedance: 20K ohms Output Impedance: 150 ohms Power draw: 150 mA Recommended fuse rating: 1 Amp Weight: 1 pound What is in the LC2i box: Two-Channel line-output converter Instructions/Specs/Warranty (on packaging) Quality Control Certificate AudioControl LC2i owner's manual Cerwin Vega H7SE10 1000W Max (200W RMS) HED Series Single 10" Sealed Shallow Mount Subwoofer Enclosure General Features: 1000W Max (200W RMS) Single 10" Sealed Shallow Mount Subwoofer Enclosure Power Handling: Peak: 1000W Total RMS: 200W Total Final Impedance: 4 ohms Preloaded with single 10" HED Series Subwoofers Sealed enclosure with black carpet finish Enclosure Dimensions: 11.88" D x 18.5" W x 6" H Authorized Internet Dealer 1-year Manufacturer's Warranty Subwoofer Features: Mounting Depth: 5 Cutout Diameter: 9.17 2" 4 Layer voice coil 4 ohms Enclosure Features: 3/4" MDF Construction Black carpet finish Shallow mount for easy installation in tight spaces Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.