Peavey (47)

Peavey MAX126 10-Watt Bass Amp Combo 6.5" MAX® 126 10-Watt Bass Amp Combo The MAX 126 bass combo amp is a 10-watt bass practice amp loaded with features that make it ideal for small rehearsals, including TransTube gain boost, multi-band EQ, Peavey exclusive DDT compression, headphone output, and auxiliary input. General Features: 10 Watts RMS into 4 Ohms 6.5" Inch Speaker Low, Mid, and High EQ Controls Volume Control Selectable Vintage Gain Control with patented Transtube circuity 1/4" Headphone Jack 1/4" aux input Built-in chromatic tuner DDT Speaker protection Weight Unpacked 11 lb (4.90 kg) Weight Packed 13 lb (5.9 kg) Width Packed 12.33"(31.3 cm) Height Packed 12.75" (32.36 cm) Depth Packed 8.25" (20.95 cm) ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

 (2) PVXP12 DSP 12 inch Powered Speaker 830W 12" Powered Speaker with 1.4" Compression Driver,+ Free Mr. Dj Speaker Stands+XLR Cable Peavey PVX 12 DSP 830W 12-inch Powered Speaker 830W 12" Powered Speaker with 1.4" Compression Driver, Quadratic Throat Waveguide Technology, DDT Compression, Asymmetrical Horn, Pole Mount, Plastic Injection-molded Trapezoidal Enclosure, and DSP (each) A Portable Loudspeaker with Onboard DSP The lightweight, road-ready Peavey PVXp 12 DSP loudspeaker provides the sound reinforcement you need. Pumping a muscular 830 watts through a powerful 12" woofer and 1.4" titanium compression driver, the PVXp 12 DSP delivers the chest-thumping low end, smooth response, low distortion, and excellent high-frequency dispersion you demand. You can tailor your sound further with this speaker's built-in digital processing. An ultra-rugged injection-molded trapezoidal enclosure and scuff-resistant powder-coated steel grille are the keys to the PVXp 12 DSP's durability, allowing it to withstand the routine wear easily comes with transporting your speakers. If you're looking for a portable PA speaker with plenty of power and projection, the PVXp 12 DSP is a top performer. Easy-to-transport, lightweight design No one likes hauling around heavy gear. Peavey built the PVXp 12 DSP to be as lightweight as possible without sacrificing durability. Moreover, the PVXp 12 DSP features several molded-in cabinet handles for extra grab-and-go convenience. When it comes to flying PVXp 12 DSP speakers, multiple in-cabinet fly points make the job easy. Built tough for life on the road Peavey PVX 12 DSP speakers are so lightweight you may be tempted to throw them in the back of your truck. Of course, we at Absolute Pro Music don't recommend this, but if you do, your PVXp 12 DSP will probably shrug off the abuse without a problem. Peavey built their PVXp 12 DSP enclosures from high-tech molded plastic, which absorbs shock and resists scratches like a champ. Plenty of power and projection Whether you're blasting music, amplifying vocals, or need a good speaker for speech sound reinforcement, your Peavey PVXp 12 DSP will do the trick. It packs 830 watts of power, driving a pair of highly efficient speakers — a pair of PVXp 12 DSPs can easily cover audiences in the hundreds. Additionally, built-in pole mounts let you easily elevate your loudspeakers, increasing their effective range. The PVXp 12 DSP's asymmetrical horn is engineered to deliver your sound where you need it (not over your audience's heads), maximizing its dispersion. Optimize your sound with Advanced DSP. Thanks to its state-of-the-art design, it's easy to get the most out of your Peavey PVXp 12 DSP. Built-in DSP tailors your sound to just about any situation you will likely encounter. Tune your speaker's performance for EDM, rock, country, hip-hop, or acoustic music, or optimize it for spoken word presentations. You can also adapt the PVXp 12 DSP to various environments and configurations, such as a typical church setting, with/without a subwoofer, indoors/outdoors, or as a stage monitor. Peavey PVX 12 DSP Features: 12" heavy-duty woofer delivers chest-thumping low-end RX 14 compression driver with 1.4" titanium diaphragm delivers smooth, high-end response Ultra-reliable fan-cooled power amps with DDT compression Patented Quadratic Throat Waveguide technology, 150 by 50-degree coverage Asymmetrical horn aims the sound down to 10 degrees (at the audience, not over their heads) Mic/Line switch provides two different gain settings Tailor your sound to different environments and configurations with built-in DSP Durable plastic injection-molded trapezoidal enclosure Full-coverage heavy-duty perforated steel grilles with powder-coat finish Pole mount molded-in for 1-3/8" diameter poles Top and bottom flying point inserts An extra angled section on the right side allows for floor monitor use Tech Specs Powered: Yes Power Configuration: Bi-amped LF Driver Size: 12" woofer, 2.3" voice coil HF Driver Size: RX14 1.4" titanium compression driver LF Driver Power Amp: 630W Peak HF Driver Power Amp: 200W Peak Total Power: 830W Peak Inputs: 1 x XLR-1/4" combo (mic/line), 2 x RCA (stereo line) Outputs: 1 x XLR (thru), 1 x 1/4" (thru) Frequency Range: 51Hz-20kHz Frequency Response: 60Hz-20kHz (±3dB) Crossover Frequency: 2.1kHz Maximum Peak SPL: 128 dB SPL @ 1m Horizontal Coverage Angle: 100 Degrees Vertical Coverage Angle: 50 Degrees Signal Processing: EQ Modes, Crossover, Limiter Enclosure Material: Plastic injection-molded trapezoidal enclosure Mounting Options: Pole Mount with 1.37" socket, 4 x M10 Fly Points, 12 x M8 Fly Points (for Versamount 70+ bracket) Power Source: Standard IEC AC cable Height: 24.5" Width: 16.1" Depth: 15" Weight: 43 lbs. Manufacturer Part Number: 03616450 ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

(2) PVXP15 DSP 15 inch Powered Speaker 830W 12" Powered Speaker with 1.4" Compression Driver,+ Free Mr. Dj Speaker Stands+XLR Cable Peavey PVXp 12 DSP 830W 12 inch Powered Speaker 830W 12" Powered Speaker with 1.4" Compression Driver, Quadratic Throat Waveguide Technology, DDT Compression, Asymmetrical Horn, Pole Mount, Plastic Injection-molded Trapezoidal Enclosure, and DSP (each) A Portable Loudspeaker with Onboard DSP The lightweight, road-ready Peavey PVXp 12 DSP loudspeaker provides you with the sound reinforcement you need. Pumping a muscular 830 watts through a powerful 12" woofer and 1.4" titanium compression driver, the PVXp 12 DSP delivers the chest-thumping low end, smooth response, low distortion, and excellent high-frequency dispersion you demand. You can tailor your sound further with this speaker's built-in digital processing. An ultra-rugged injection-molded trapezoidal enclosure and scuff-resistant powder-coated steel grille are the keys to the PVXp 12 DSP's durability, allowing it to easily withstand the routine wear that comes with transporting your speakers. If you're looking for a portable PA speaker with plenty of power and projection, the PVXp 12 DSP is a top performer. Easy-to-transport, lightweight design No one likes hauling around heavy gear. That's why Peavey built the PVXp 12 DSP to be as lightweight as possible without sacrificing durability. What's more, the PVXp 12 DSP features a number of molded-in cabinet handles for extra grab-and-go convenience. And when it comes to flying PVXp 12 DSP speakers, multiple in-cabinet fly points make the job easy. Built tough for life on the road Peavey PVXp 12 DSP speakers are so lightweight, you may just be tempted to literally throw them in the back of your truck. Of course, we at Absolute Pro Music don't recommend this, but if you do, your PVXp 12 DSP will probably shrug off the abuse without a problem. That's because Peavey built their PVXp 12 DSP enclosures from high-tech molded plastic, which absorbs shock and resists scratches like a champ. Plenty of power and projection Whether you're blasting music, amplifying vocals, or just need a good speaker for speech sound reinforcement, your Peavey PVXp 12 DSP will do the trick. It packs 830 watts of power, driving a pair of highly efficient speakers — a pair of PVXp 12 DSPs can easily cover audiences in the hundreds. What's more, built-in pole mounts let you easily elevate your loudspeakers, increasing their effective range. And the PVXp 12 DSP's asymmetrical horn is engineered to deliver your sound where you need it (not over your audience's heads), maximizing its dispersion. Optimize your sound with Advanced DSP It's easy to get the most out of your Peavey PVXp 12 DSP, thanks to its state-of-the-art design. Built-in DSP tailors your sound to just about any situation you're likely to encounter. Tune your speaker's performance for EDM, rock, country, hip-hop, or acoustic music, or optimize it for spoken word presentations. You can also adapt the PVXp 12 DSP to various environments and configurations, such as a typical church setting, with/without a subwoofer, indoors/outdoors, or as a stage monitor. Peavey PVXp 12 DSP Features: 12" heavy-duty woofer delivers chest-thumping low end RX 14 compression driver with 1.4" titanium diaphragm delivers smooth high-end response Ultra-reliable fan-cooled power amps with DDT compression Patented Quadratic Throat Waveguide technology, 150 by 50-degree coverage Asymmetrical horn aims the sound down to 10 degrees (at the audience, not over their heads) Mic/Line switch provides two different gain settings Tailor your sound to different environments and configurations with built-in DSP Durable plastic injection-molded trapezoidal enclosure Full-coverage heavy-duty perforated steel grilles, with powder-coat finish Pole mount molded-in for 1-3/8" diameter poles Top and bottom flying point inserts Extra angled section on right side allows for floor monitor use Tech Specs Powered: Yes Power Configuration: Bi-amped LF Driver Size: 12" woofer, 2.3" voice coil HF Driver Size: RX14 1.4" titanium compression driver LF Driver Power Amp: 630W Peak HF Driver Power Amp: 200W Peak Total Power: 830W Peak Inputs: 1 x XLR-1/4" combo (mic/line), 2 x RCA (stereo line) Outputs: 1 x XLR (thru), 1 x 1/4" (thru) Frequency Range: 51Hz-20kHz Frequency Response: 60Hz-20kHz (±3dB) Crossover Frequency: 2.1kHz Maximum Peak SPL: 128 dB SPL @ 1m Horizontal Coverage Angle: 100 Degrees Vertical Coverage Angle: 50 Degrees Signal Processing: EQ Modes, Crossover, Limiter Enclosure Material: Plastic injection-molded trapezoidal enclosure Mounting Options: Pole Mount with 1.37" socket, 4 x M10 Fly Points, 12 x M8 Fly Points (for Versamount 70+ bracket) Power Source: Standard IEC AC cable Height: 24.5" Width: 16.1" Depth: 15" Weight: 43 lbs. Manufacturer Part Number: 03616450 ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Peavey PVXP15 DSP 15 inch Powered Speaker 800W 15" Powered Speaker with 1.4" Compression Driver,+ Free Mr. Dj XLR Cables Peavey PVXp15-DSP 800W 15 inch Powered Speaker 800W 15" Powered Speaker with 1.4" Compression Driver, Quadratic Throat Waveguide Technology, DDT Compression, Asymmetrical Horn, Pole Mount, Plastic Injection-molded Trapezoidal Enclosure, and DSP (each) A Portable Loudspeaker with Onboard DSP The lightweight, road-ready Peavey PVXp 15 DSP loudspeaker provides you with the sound reinforcement you need. Pumping a muscular 800 watts through a powerful 15" woofer and 1.4" titanium compression driver, the PVXp 15 DSP delivers the chest-thumping low end, smooth response, low distortion, and excellent high-frequency dispersion you demand. You can tailor your sound further with this speaker's built-in digital processing. An ultra-rugged injection-molded trapezoidal enclosure and scuff-resistant powder-coated steel grille are the keys to the PVXp 15 DSP's durability, allowing it to easily withstand the routine wear that comes with transporting your speakers. If you're looking for a portable PA speaker with plenty of power and projection, the PVXp 15 DSP is a top performer. Easy-to-transport, lightweight design No one likes hauling around heavy gear. That's why Peavey built the PVXp 15 DSP to be as lightweight as possible without sacrificing durability. What's more, the PVXp 15 DSP features a number of molded-in cabinet handles for extra grab-and-go convenience. And when it comes to flying PVXp 15 DSP speakers, multiple in-cabinet fly points make the job easy. Built tough for life on the road Peavey PVXp 15 DSP speakers are so lightweight, you may just be tempted to literally throw them in the back of your truck. Of course, we at Absolute Pro Music don't recommend this, but if you do, your PVXp 15 DSP will probably shrug off the abuse without a problem. That's because Peavey built their PVXp 15 DSP enclosures from high-tech molded plastic, which absorbs shock and resists scratches like a champ. Plenty of power and projection Whether you're blasting music, amplifying vocals, or just need a good speaker for speech sound reinforcement, your Peavey PVXp 15 DSP will do the trick. It packs 800 watts of power, driving a pair of highly efficient speakers — a pair of PVXp 15 DSPs can easily cover audiences in the hundreds. What's more, built-in pole mounts let you easily elevate your loudspeakers, increasing their effective range. And the PVXp 15 DSP's asymmetrical horn is engineered to deliver your sound where you need it (not over your audience's heads), maximizing its dispersion. Optimize your sound with Advanced DSP It's easy to get the most out of your Peavey PVXp 15 DSP, thanks to its state-of-the-art design. Built-in DSP tailors your sound to just about any situation you're likely to encounter. Tune your speaker's performance for EDM, rock, country, hip-hop, or acoustic music, or optimize it for spoken word presentations. You can also adapt the PVXp 15 DSP to various environments and configurations, such as a typical church setting, with/without a subwoofer, indoors/outdoors, or as a stage monitor. Peavey PVXp 15 DSP Features: 15" heavy-duty woofer delivers chest-thumping low end RX 14 compression driver with 1.4" titanium diaphragm delivers smooth high-end response Ultra-reliable fan-cooled power amps with DDT compression Patented Quadratic Throat Waveguide technology, 150 by 50-degree coverage Asymmetrical horn aims the sound down to 15 degrees (at the audience, not over their heads) Mic/Line switch provides two different gain settings Tailor your sound to different environments and configurations with built-in DSP Durable plastic injection-molded trapezoidal enclosure Full-coverage heavy-duty perforated steel grilles, with powder-coat finish Pole mount molded-in for 1-3/8" diameter poles Top and bottom flying point inserts Extra angled section on right side allows for floor monitor use Tech Specs Powered: Yes Power Configuration: Bi-amped LF Driver Size: 15" woofer, 2.3" voice coil HF Driver Size: RX14 1.4" titanium compression driver LF Driver Power Amp: 630W Peak HF Driver Power Amp: 200W Peak Total Power: 830W Peak Inputs: 1 x XLR-1/4" combo (mic/line), 2 x RCA (stereo line) Outputs: 1 x XLR (thru), 1 x 1/4" (thru) Frequency Range: 49Hz-20kHz Frequency Response: 58Hz-20kHz (±3dB) Crossover Frequency: 2.1kHz Maximum Peak SPL: 128 dB SPL @ 1m Horizontal Coverage Angle: 100 Degrees Vertical Coverage Angle: 50 Degrees Signal Processing: EQ Modes, Crossover, Limiter Enclosure Material: Plastic injection-molded trapezoidal enclosure Mounting Options: Pole Mount with 1.37" socket, 4 x M10 Fly Points, 12 x M8 Fly Points (for Versamount 70+ bracket) Power Source: Standard IEC AC cable Height: 28.25" Width: 18.9" Depth: 18.7" Weight: 51 lbs. Manufacturer Part Number: 03616470 ⚠️Warning: Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Peavey PVXP15 DSP 15 inch Powered Speaker 800W 15" Powered Speaker with 1.4" Compression Driver,+ Free Mr. Dj Speaker Stand Peavey PVXp15-DSP 800W 15 inch Powered Speaker 800W 15" Powered Speaker with 1.4" Compression Driver, Quadratic Throat Waveguide Technology, DDT Compression, Asymmetrical Horn, Pole Mount, Plastic Injection-molded Trapezoidal Enclosure, and DSP (each) A Portable Loudspeaker with Onboard DSP The lightweight, road-ready Peavey PVXp 15 DSP loudspeaker provides you with the sound reinforcement you need. Pumping a muscular 800 watts through a powerful 15" woofer and 1.4" titanium compression driver, the PVXp 15 DSP delivers the chest-thumping low end, smooth response, low distortion, and excellent high-frequency dispersion you demand. You can tailor your sound further with this speaker's built-in digital processing. An ultra-rugged injection-molded trapezoidal enclosure and scuff-resistant powder-coated steel grille are the keys to the PVXp 15 DSP's durability, allowing it to easily withstand the routine wear that comes with transporting your speakers. If you're looking for a portable PA speaker with plenty of power and projection, the PVXp 15 DSP is a top performer. Easy-to-transport, lightweight design No one likes hauling around heavy gear. That's why Peavey built the PVXp 15 DSP to be as lightweight as possible without sacrificing durability. What's more, the PVXp 15 DSP features a number of molded-in cabinet handles for extra grab-and-go convenience. And when it comes to flying PVXp 15 DSP speakers, multiple in-cabinet fly points make the job easy. Built tough for life on the road Peavey PVXp 15 DSP speakers are so lightweight, you may just be tempted to literally throw them in the back of your truck. Of course, we at Absolute Pro Music don't recommend this, but if you do, your PVXp 15 DSP will probably shrug off the abuse without a problem. That's because Peavey built their PVXp 15 DSP enclosures from high-tech molded plastic, which absorbs shock and resists scratches like a champ. Plenty of power and projection Whether you're blasting music, amplifying vocals, or just need a good speaker for speech sound reinforcement, your Peavey PVXp 15 DSP will do the trick. It packs 800 watts of power, driving a pair of highly efficient speakers — a pair of PVXp 15 DSPs can easily cover audiences in the hundreds. What's more, built-in pole mounts let you easily elevate your loudspeakers, increasing their effective range. And the PVXp 15 DSP's asymmetrical horn is engineered to deliver your sound where you need it (not over your audience's heads), maximizing its dispersion. Optimize your sound with Advanced DSP It's easy to get the most out of your Peavey PVXp 15 DSP, thanks to its state-of-the-art design. Built-in DSP tailors your sound to just about any situation you're likely to encounter. Tune your speaker's performance for EDM, rock, country, hip-hop, or acoustic music, or optimize it for spoken word presentations. You can also adapt the PVXp 15 DSP to various environments and configurations, such as a typical church setting, with/without a subwoofer, indoors/outdoors, or as a stage monitor. Peavey PVXp 15 DSP Features: 15" heavy-duty woofer delivers chest-thumping low end RX 14 compression driver with 1.4" titanium diaphragm delivers smooth high-end response Ultra-reliable fan-cooled power amps with DDT compression Patented Quadratic Throat Waveguide technology, 150 by 50-degree coverage Asymmetrical horn aims the sound down to 15 degrees (at the audience, not over their heads) Mic/Line switch provides two different gain settings Tailor your sound to different environments and configurations with built-in DSP Durable plastic injection-molded trapezoidal enclosure Full-coverage heavy-duty perforated steel grilles, with powder-coat finish Pole mount molded-in for 1-3/8" diameter poles Top and bottom flying point inserts Extra angled section on right side allows for floor monitor use Tech Specs Powered: Yes Power Configuration: Bi-amped LF Driver Size: 15" woofer, 2.3" voice coil HF Driver Size: RX14 1.4" titanium compression driver LF Driver Power Amp: 630W Peak HF Driver Power Amp: 200W Peak Total Power: 830W Peak Inputs: 1 x XLR-1/4" combo (mic/line), 2 x RCA (stereo line) Outputs: 1 x XLR (thru), 1 x 1/4" (thru) Frequency Range: 49Hz-20kHz Frequency Response: 58Hz-20kHz (±3dB) Crossover Frequency: 2.1kHz Maximum Peak SPL: 128 dB SPL @ 1m Horizontal Coverage Angle: 100 Degrees Vertical Coverage Angle: 50 Degrees Signal Processing: EQ Modes, Crossover, Limiter Enclosure Material: Plastic injection-molded trapezoidal enclosure Mounting Options: Pole Mount with 1.37" socket, 4 x M10 Fly Points, 12 x M8 Fly Points (for Versamount 70+ bracket) Power Source: Standard IEC AC cable Height: 28.25" Width: 18.9" Depth: 18.7" Weight: 51 lbs. Manufacturer Part Number: 03616470 ⚠️Warning: Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Peavey PVXP15 DSP 15-inch Powered Speaker 800W 15" Powered Speaker with 1.4" Compression Driver, Peavey PVXp15-DSP 800W 15-inch Powered Speaker 800W 15" Powered Speaker with 1.4" Compression Driver, Quadratic Throat Waveguide Technology, DDT Compression, Asymmetrical Horn, Pole Mount, Plastic Injection-molded Trapezoidal Enclosure, and DSP (each) A Portable Loudspeaker with Onboard DSP The lightweight, road-ready Peavey PVXp 15 DSP loudspeaker provides the sound reinforcement you need. Pumping a muscular 800 watts through a powerful 15" woofer and 1.4" titanium compression driver, the PVXp 15 DSP delivers the chest-thumping low end, smooth response, low distortion, and excellent high-frequency dispersion you demand. You can tailor your sound further with this speaker's built-in digital processing. An ultra-rugged injection-molded trapezoidal enclosure and scuff-resistant powder-coated steel grille are the keys to the PVXp 15 DSP's durability, allowing it to withstand the routine wear that quickly comes with transporting your speakers. If you're looking for a portable PA speaker with plenty of power and projection, the PVXp 15 DSP is a top performer. Easy-to-transport, lightweight design No one likes hauling around heavy gear. Peavey built the PVXp 15 DSP to be as lightweight as possible without sacrificing durability. Moreover, the PVXp 15 DSP features several molded-in cabinets handles for extra grab-and-go convenience. And when it comes to flying PVXp 15 DSP speakers, multiple in-cabinet fly points make the job easy. Built tough for life on the road Peavey PVXp 15 DSP speakers are so lightweight you may just be tempted to throw them in the back of your truck. Of course, we at Absolute Pro Music don't recommend this, but if you do, your PVXp 15 DSP will probably shrug off the abuse without a problem. That's because Peavey built their PVXp 15 DSP enclosures from high-tech molded plastic, which absorbs shock and resists scratches like a champ. Plenty of power and projection Whether you're blasting music, amplifying vocals, or need a good speaker for speech sound reinforcement, your Peavey PVXp 15 DSP will do the trick. It packs 800 watts of power, driving a pair of highly efficient speakers — a pair of PVXp 15 DSPs can easily cover audiences in the hundreds. Additionally, built-in pole mounts let you easily elevate your loudspeakers, increasing their effective range. And the PVXp 15 DSP's asymmetrical horn is engineered to deliver your sound where you need it (not over your audience's heads), maximizing its dispersion. Optimize your sound with Advanced DSP It's easy to get the most out of your Peavey PVXp 15 DSP, thanks to its state-of-the-art design. Built-in DSP tailors your sound to just about any situation you're likely to encounter. Tune your speaker's performance for EDM, rock, country, hip-hop, or acoustic music, or optimize it for spoken word presentations. You can also adapt the PVXp 15 DSP to various environments and configurations, such as a typical church setting, with/without a subwoofer, indoors/outdoors, or as a stage monitor. Peavey PVXp 15 DSP Features: 15" heavy-duty woofer delivers chest-thumping low end RX 14 compression driver with 1.4" titanium diaphragm delivers smooth high-end response Ultra-reliable fan-cooled power amps with DDT compression Patented Quadratic Throat Waveguide technology, 150 by 50-degree coverage Asymmetrical horn aims the sound down to 15 degrees (at the audience, not over their heads) Mic/Line switch provides two different gain settings Tailor your sound to different environments and configurations with built-in DSP Durable plastic injection-molded trapezoidal enclosure Full-coverage heavy-duty perforated steel grilles with powder-coat finish Pole mount molded-in for 1-3/8" diameter poles Top and bottom flying point inserts The extra angled section on the right side allows for floor monitor use Tech Specs Powered: Yes Power Configuration: Bi-amped LF Driver Size: 15" woofer, 2.3" voice coil HF Driver Size: RX14 1.4" titanium compression driver LF Driver Power Amp: 630W Peak HF Driver Power Amp: 200W Peak Total Power: 830W Peak Inputs: 1 x XLR-1/4" combo (mic/line), 2 x RCA (stereo line) Outputs: 1 x XLR (thru), 1 x 1/4" (thru) Frequency Range: 49Hz-20kHz Frequency Response: 58Hz-20kHz (±3dB) Crossover Frequency: 2.1kHz Maximum Peak SPL: 128 dB SPL @ 1m Horizontal Coverage Angle: 100 Degrees Vertical Coverage Angle: 50 Degrees Signal Processing: EQ Modes, Crossover, Limiter Enclosure Material: Plastic injection-molded trapezoidal enclosure Mounting Options: Pole Mount with 1.37" socket, 4 x M10 Fly Points, 12 x M8 Fly Points (for Versamount 70+ bracket) Power Source: Standard IEC AC cable Height: 28.25" Width: 18.9" Depth: 18.7" Weight: 51 lbs. Manufacturer Part Number: 03616470 ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

  (2) PVXP15 DSP 15 inch Powered Speaker 830W 15" Powered Speaker with 1.4" Compression Driver,+ Free Mr. Dj XLR Cables Peavey PVXp 12 DSP 830W 12 inch Powered Speaker 830W 12" Powered Speaker with 1.4" Compression Driver, Quadratic Throat Waveguide Technology, DDT Compression, Asymmetrical Horn, Pole Mount, Plastic Injection-molded Trapezoidal Enclosure, and DSP (each) A Portable Loudspeaker with Onboard DSP The lightweight, road-ready Peavey PVXp 12 DSP loudspeaker provides you with the sound reinforcement you need. Pumping a muscular 830 watts through a powerful 12" woofer and 1.4" titanium compression driver, the PVXp 12 DSP delivers the chest-thumping low end, smooth response, low distortion, and excellent high-frequency dispersion you demand. You can tailor your sound further with this speaker's built-in digital processing. An ultra-rugged injection-molded trapezoidal enclosure and scuff-resistant powder-coated steel grille are the keys to the PVXp 12 DSP's durability, allowing it to easily withstand the routine wear that comes with transporting your speakers. If you're looking for a portable PA speaker with plenty of power and projection, the PVXp 12 DSP is a top performer. Easy-to-transport, lightweight design No one likes hauling around heavy gear. That's why Peavey built the PVXp 12 DSP to be as lightweight as possible without sacrificing durability. What's more, the PVXp 12 DSP features a number of molded-in cabinet handles for extra grab-and-go convenience. And when it comes to flying PVXp 12 DSP speakers, multiple in-cabinet fly points make the job easy. Built tough for life on the road Peavey PVXp 12 DSP speakers are so lightweight, you may just be tempted to literally throw them in the back of your truck. Of course, we at Absolute Pro Music don't recommend this, but if you do, your PVXp 12 DSP will probably shrug off the abuse without a problem. That's because Peavey built their PVXp 12 DSP enclosures from high-tech molded plastic, which absorbs shock and resists scratches like a champ. Plenty of power and projection Whether you're blasting music, amplifying vocals, or just need a good speaker for speech sound reinforcement, your Peavey PVXp 12 DSP will do the trick. It packs 830 watts of power, driving a pair of highly efficient speakers — a pair of PVXp 12 DSPs can easily cover audiences in the hundreds. What's more, built-in pole mounts let you easily elevate your loudspeakers, increasing their effective range. And the PVXp 12 DSP's asymmetrical horn is engineered to deliver your sound where you need it (not over your audience's heads), maximizing its dispersion. Optimize your sound with Advanced DSP It's easy to get the most out of your Peavey PVXp 12 DSP, thanks to its state-of-the-art design. Built-in DSP tailors your sound to just about any situation you're likely to encounter. Tune your speaker's performance for EDM, rock, country, hip-hop, or acoustic music, or optimize it for spoken word presentations. You can also adapt the PVXp 12 DSP to various environments and configurations, such as a typical church setting, with/without a subwoofer, indoors/outdoors, or as a stage monitor. Peavey PVXp 12 DSP Features: 12" heavy-duty woofer delivers chest-thumping low end RX 14 compression driver with 1.4" titanium diaphragm delivers smooth high-end response Ultra-reliable fan-cooled power amps with DDT compression Patented Quadratic Throat Waveguide technology, 150 by 50-degree coverage Asymmetrical horn aims the sound down to 10 degrees (at the audience, not over their heads) Mic/Line switch provides two different gain settings Tailor your sound to different environments and configurations with built-in DSP Durable plastic injection-molded trapezoidal enclosure Full-coverage heavy-duty perforated steel grilles, with powder-coat finish Pole mount molded-in for 1-3/8" diameter poles Top and bottom flying point inserts Extra angled section on right side allows for floor monitor use Tech Specs Powered: Yes Power Configuration: Bi-amped LF Driver Size: 12" woofer, 2.3" voice coil HF Driver Size: RX14 1.4" titanium compression driver LF Driver Power Amp: 630W Peak HF Driver Power Amp: 200W Peak Total Power: 830W Peak Inputs: 1 x XLR-1/4" combo (mic/line), 2 x RCA (stereo line) Outputs: 1 x XLR (thru), 1 x 1/4" (thru) Frequency Range: 51Hz-20kHz Frequency Response: 60Hz-20kHz (±3dB) Crossover Frequency: 2.1kHz Maximum Peak SPL: 128 dB SPL @ 1m Horizontal Coverage Angle: 100 Degrees Vertical Coverage Angle: 50 Degrees Signal Processing: EQ Modes, Crossover, Limiter Enclosure Material: Plastic injection-molded trapezoidal enclosure Mounting Options: Pole Mount with 1.37" socket, 4 x M10 Fly Points, 12 x M8 Fly Points (for Versamount 70+ bracket) Power Source: Standard IEC AC cable Height: 24.5" Width: 16.1" Depth: 15" Weight: 43 lbs. Manufacturer Part Number: 03616450 ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

 (2) PVXP12 DSP 12 inch Powered Speaker 830W 12" Powered Speaker with 1.4" Compression Driver,+ Free Mr. Dj XLR Cable Peavey PVXp 12 DSP 830W 12-inch Powered Speaker 830W 12" Powered Speaker with 1.4" Compression Driver, Quadratic Throat Waveguide Technology, DDT Compression, Asymmetrical Horn, Pole Mount, Plastic Injection-molded Trapezoidal Enclosure, and DSP (each) A Portable Loudspeaker with Onboard DSP The lightweight, road-ready Peavey PVXp 12 DSP loudspeaker provides the sound reinforcement you need. Pumping a muscular 830 watts through a powerful 12" woofer and 1.4" titanium compression driver, the PVXp 12 DSP delivers the chest-thumping low end, smooth response, low distortion, and excellent high-frequency dispersion you demand. You can tailor your sound further with this speaker's built-in digital processing. An ultra-rugged injection-molded trapezoidal enclosure and scuff-resistant powder-coated steel grille are the keys to the PVXp 12 DSP's durability, allowing it to easily withstand the routine wear that comes with transporting your speakers. If you're looking for a portable PA speaker with plenty of power and projection, the PVXp 12 DSP is a top performer. Easy-to-transport, lightweight design No one likes hauling around heavy gear. Peavey built the PVXp 12 DSP to be as lightweight as possible without sacrificing durability. What's more, the PVXp 12 DSP features several molded-in cabinet handles for extra grab-and-go convenience. And when it comes to flying PVXp 12 DSP speakers, multiple in-cabinet fly points make the job easy. Built tough for life on the road Peavey PVXp 12 DSP speakers are so lightweight you may just be tempted to throw them in the back of your truck literally. Of course, we at Absolute Pro Music don't recommend this, but if you do, your PVXp 12 DSP will probably shrug off the abuse without a problem. That's because Peavey built their PVXp 12 DSP enclosures from high-tech molded plastic, which absorbs shock and resists scratches like a champ. Plenty of power and projection Whether you're blasting music, amplifying vocals, or need a good speaker for speech sound reinforcement, your Peavey PVXp 12 DSP will do the trick. It packs 830 watts of power, driving a pair of highly efficient speakers — a pair of PVXp 12 DSPs can easily cover audiences in the hundreds. Additionally, built-in pole mounts let you easily elevate your loudspeakers, increasing their effective range. And the PVXp 12 DSP's asymmetrical horn is engineered to deliver your sound where you need it (not over your audience's heads), maximizing its dispersion. Optimize your sound with Advanced DSP It's easy to get the most out of your Peavey PVXp 12 DSP, thanks to its state-of-the-art design. Built-in DSP tailors your sound to just about any situation you're likely to encounter. Tune your speaker's performance for EDM, rock, country, hip-hop, or acoustic music, or optimize it for spoken word presentations. You can also adapt the PVXp 12 DSP to various environments and configurations, such as a typical church setting, with/without a subwoofer, indoors/outdoors, or as a stage monitor. Peavey PVXp 12 DSP Features: 12" heavy-duty woofer delivers chest-thumping low end RX 14 compression driver with 1.4" titanium diaphragm delivers smooth high-end response Ultra-reliable fan-cooled power amps with DDT compression Patented Quadratic Throat Waveguide technology, 150 by 50-degree coverage Asymmetrical horn aims the sound down to 10 degrees (at the audience, not over their heads) Mic/Line switch provides two different gain settings Tailor your sound to different environments and configurations with built-in DSP Durable plastic injection-molded trapezoidal enclosure Full-coverage heavy-duty perforated steel grilles with powder-coat finish Pole mount molded-in for 1-3/8" diameter poles Top and bottom flying point inserts The extra angled section on the right side allows for floor monitor use Tech Specs Powered: Yes Power Configuration: Bi-amped LF Driver Size: 12" woofer, 2.3" voice coil HF Driver Size: RX14 1.4" titanium compression driver LF Driver Power Amp: 630W Peak HF Driver Power Amp: 200W Peak Total Power: 830W Peak Inputs: 1 x XLR-1/4" combo (mic/line), 2 x RCA (stereo line) Outputs: 1 x XLR (thru), 1 x 1/4" (thru) Frequency Range: 51Hz-20kHz Frequency Response: 60Hz-20kHz (±3dB) Crossover Frequency: 2.1kHz Maximum Peak SPL: 128 dB SPL @ 1m Horizontal Coverage Angle: 100 Degrees Vertical Coverage Angle: 50 Degrees Signal Processing: EQ Modes, Crossover, Limiter Enclosure Material: Plastic injection-molded trapezoidal enclosure Mounting Options: Pole Mount with 1.37" socket, 4 x M10 Fly Points, 12 x M8 Fly Points (for Versamount 70+ bracket) Power Source: Standard IEC AC cable Height: 24.5" Width: 16.1" Depth: 15" Weight: 43 lbs. Manufacturer Part Number: 03616450 ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Peavey PVXP12 DSP 12 inch Powered Speaker 830W 12" Powered Speaker with 1.4" Compression Driver,+ Free Mr. Dj XLR Cable Peavey PVXp 12 DSP 830W 12 inch Powered Speaker 830W 12" Powered Speaker with 1.4" Compression Driver, Quadratic Throat Waveguide Technology, DDT Compression, Asymmetrical Horn, Pole Mount, Plastic Injection-molded Trapezoidal Enclosure, and DSP (each) A Portable Loudspeaker with Onboard DSP The lightweight, road-ready Peavey PVXp 12 DSP loudspeaker provides you with the sound reinforcement you need. Pumping a muscular 830 watts through a powerful 12" woofer and 1.4" titanium compression driver, the PVXp 12 DSP delivers the chest-thumping low end, smooth response, low distortion, and excellent high-frequency dispersion you demand. You can tailor your sound further with this speaker's built-in digital processing. An ultra-rugged injection-molded trapezoidal enclosure and scuff-resistant powder-coated steel grille are the keys to the PVXp 12 DSP's durability, allowing it to easily withstand the routine wear that comes with transporting your speakers. If you're looking for a portable PA speaker with plenty of power and projection, the PVXp 12 DSP is a top performer. Easy-to-transport, lightweight design No one likes hauling around heavy gear. That's why Peavey built the PVXp 12 DSP to be as lightweight as possible without sacrificing durability. What's more, the PVXp 12 DSP features a number of molded-in cabinet handles for extra grab-and-go convenience. And when it comes to flying PVXp 12 DSP speakers, multiple in-cabinet fly points make the job easy. Built tough for life on the road Peavey PVXp 12 DSP speakers are so lightweight, you may just be tempted to literally throw them in the back of your truck. Of course, we at Absolute Pro Music don't recommend this, but if you do, your PVXp 12 DSP will probably shrug off the abuse without a problem. That's because Peavey built their PVXp 12 DSP enclosures from high-tech molded plastic, which absorbs shock and resists scratches like a champ. Plenty of power and projection Whether you're blasting music, amplifying vocals, or just need a good speaker for speech sound reinforcement, your Peavey PVXp 12 DSP will do the trick. It packs 830 watts of power, driving a pair of highly efficient speakers — a pair of PVXp 12 DSPs can easily cover audiences in the hundreds. What's more, built-in pole mounts let you easily elevate your loudspeakers, increasing their effective range. And the PVXp 12 DSP's asymmetrical horn is engineered to deliver your sound where you need it (not over your audience's heads), maximizing its dispersion. Optimize your sound with Advanced DSP It's easy to get the most out of your Peavey PVXp 12 DSP, thanks to its state-of-the-art design. Built-in DSP tailors your sound to just about any situation you're likely to encounter. Tune your speaker's performance for EDM, rock, country, hip-hop, or acoustic music, or optimize it for spoken word presentations. You can also adapt the PVXp 12 DSP to various environments and configurations, such as a typical church setting, with/without a subwoofer, indoors/outdoors, or as a stage monitor. Peavey PVXp 12 DSP Features: 12" heavy-duty woofer delivers chest-thumping low end RX 14 compression driver with 1.4" titanium diaphragm delivers smooth high-end response Ultra-reliable fan-cooled power amps with DDT compression Patented Quadratic Throat Waveguide technology, 150 by 50-degree coverage Asymmetrical horn aims the sound down to 10 degrees (at the audience, not over their heads) Mic/Line switch provides two different gain settings Tailor your sound to different environments and configurations with built-in DSP Durable plastic injection-molded trapezoidal enclosure Full-coverage heavy-duty perforated steel grilles, with powder-coat finish Pole mount molded-in for 1-3/8" diameter poles Top and bottom flying point inserts Extra angled section on right side allows for floor monitor use Tech Specs Powered: Yes Power Configuration: Bi-amped LF Driver Size: 12" woofer, 2.3" voice coil HF Driver Size: RX14 1.4" titanium compression driver LF Driver Power Amp: 630W Peak HF Driver Power Amp: 200W Peak Total Power: 830W Peak Inputs: 1 x XLR-1/4" combo (mic/line), 2 x RCA (stereo line) Outputs: 1 x XLR (thru), 1 x 1/4" (thru) Frequency Range: 51Hz-20kHz Frequency Response: 60Hz-20kHz (±3dB) Crossover Frequency: 2.1kHz Maximum Peak SPL: 128 dB SPL @ 1m Horizontal Coverage Angle: 100 Degrees Vertical Coverage Angle: 50 Degrees Signal Processing: EQ Modes, Crossover, Limiter Enclosure Material: Plastic injection-molded trapezoidal enclosure Mounting Options: Pole Mount with 1.37" socket, 4 x M10 Fly Points, 12 x M8 Fly Points (for Versamount 70+ bracket) Power Source: Standard IEC AC cable Height: 24.5" Width: 16.1" Depth: 15" Weight: 43 lbs. Manufacturer Part Number: 03616450 ⚠️Warning: Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Peavey PVXP12 DSP 12 inch Powered Speaker 830W 12" Powered Speaker with 1.4" Compression Driver,+ Free Mr. Dj Speaker Stand Peavey PVXp 12 DSP 830W 12 inch Powered Speaker 830W 12" Powered Speaker with 1.4" Compression Driver, Quadratic Throat Waveguide Technology, DDT Compression, Asymmetrical Horn, Pole Mount, Plastic Injection-molded Trapezoidal Enclosure, and DSP (each) A Portable Loudspeaker with Onboard DSP The lightweight, road-ready Peavey PVXp 12 DSP loudspeaker provides you with the sound reinforcement you need. Pumping a muscular 830 watts through a powerful 12" woofer and 1.4" titanium compression driver, the PVXp 12 DSP delivers the chest-thumping low end, smooth response, low distortion, and excellent high-frequency dispersion you demand. You can tailor your sound further with this speaker's built-in digital processing. An ultra-rugged injection-molded trapezoidal enclosure and scuff-resistant powder-coated steel grille are the keys to the PVXp 12 DSP's durability, allowing it to easily withstand the routine wear that comes with transporting your speakers. If you're looking for a portable PA speaker with plenty of power and projection, the PVXp 12 DSP is a top performer. Easy-to-transport, lightweight design No one likes hauling around heavy gear. That's why Peavey built the PVXp 12 DSP to be as lightweight as possible without sacrificing durability. What's more, the PVXp 12 DSP features a number of molded-in cabinet handles for extra grab-and-go convenience. And when it comes to flying PVXp 12 DSP speakers, multiple in-cabinet fly points make the job easy. Built tough for life on the road Peavey PVXp 12 DSP speakers are so lightweight, you may just be tempted to literally throw them in the back of your truck. Of course, we at Absolute Pro Music don't recommend this, but if you do, your PVXp 12 DSP will probably shrug off the abuse without a problem. That's because Peavey built their PVXp 12 DSP enclosures from high-tech molded plastic, which absorbs shock and resists scratches like a champ. Plenty of power and projection Whether you're blasting music, amplifying vocals, or just need a good speaker for speech sound reinforcement, your Peavey PVXp 12 DSP will do the trick. It packs 830 watts of power, driving a pair of highly efficient speakers — a pair of PVXp 12 DSPs can easily cover audiences in the hundreds. What's more, built-in pole mounts let you easily elevate your loudspeakers, increasing their effective range. And the PVXp 12 DSP's asymmetrical horn is engineered to deliver your sound where you need it (not over your audience's heads), maximizing its dispersion. Optimize your sound with Advanced DSP It's easy to get the most out of your Peavey PVXp 12 DSP, thanks to its state-of-the-art design. Built-in DSP tailors your sound to just about any situation you're likely to encounter. Tune your speaker's performance for EDM, rock, country, hip-hop, or acoustic music, or optimize it for spoken word presentations. You can also adapt the PVXp 12 DSP to various environments and configurations, such as a typical church setting, with/without a subwoofer, indoors/outdoors, or as a stage monitor. Peavey PVXp 12 DSP Features: 12" heavy-duty woofer delivers chest-thumping low end RX 14 compression driver with 1.4" titanium diaphragm delivers smooth high-end response Ultra-reliable fan-cooled power amps with DDT compression Patented Quadratic Throat Waveguide technology, 150 by 50-degree coverage Asymmetrical horn aims the sound down to 10 degrees (at the audience, not over their heads) Mic/Line switch provides two different gain settings Tailor your sound to different environments and configurations with built-in DSP Durable plastic injection-molded trapezoidal enclosure Full-coverage heavy-duty perforated steel grilles, with powder-coat finish Pole mount molded-in for 1-3/8" diameter poles Top and bottom flying point inserts Extra angled section on right side allows for floor monitor use Tech Specs Powered: Yes Power Configuration: Bi-amped LF Driver Size: 12" woofer, 2.3" voice coil HF Driver Size: RX14 1.4" titanium compression driver LF Driver Power Amp: 630W Peak HF Driver Power Amp: 200W Peak Total Power: 830W Peak Inputs: 1 x XLR-1/4" combo (mic/line), 2 x RCA (stereo line) Outputs: 1 x XLR (thru), 1 x 1/4" (thru) Frequency Range: 51Hz-20kHz Frequency Response: 60Hz-20kHz (±3dB) Crossover Frequency: 2.1kHz Maximum Peak SPL: 128 dB SPL @ 1m Horizontal Coverage Angle: 100 Degrees Vertical Coverage Angle: 50 Degrees Signal Processing: EQ Modes, Crossover, Limiter Enclosure Material: Plastic injection-molded trapezoidal enclosure Mounting Options: Pole Mount with 1.37" socket, 4 x M10 Fly Points, 12 x M8 Fly Points (for Versamount 70+ bracket) Power Source: Standard IEC AC cable Height: 24.5" Width: 16.1" Depth: 15" Weight: 43 lbs. Manufacturer Part Number: 03616450 ⚠️Warning: Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Peavey MAX 250 1x15" 250-watt Bass Combo Amp+ Free Mr Dj Instrument Cable+Phone Holder 250W, 1-channel, Solid-state, 1x15" Bass Combo Amp with 3-band EQ, Overdrive, Contour, Mid Shift, Bright, Kosmos-C, DDT Speaker Protection, Effects Loop, Speaker Out, and Tuner - Black Tailor-made for Performing Bassists The Peavey MAX 250's feature-rich design was tailor-made for performing bassists. This 250-watt bass combo amp includes plenty of onboard sound shaping, with a 3-band EQ and Overdrive, Contour, Mid Shift, and Bright controls. Kosmos-C bass enhancement imparts harmonics and subharmonics for maximum impact and tone. Clip-limiting DDT tames your dynamics and protects your speakers. Integrating your pedals and external processors is a breeze, thanks to the MAX 250's effects loop. Expanding your rig is just as easy, courtesy of the MAX 250's speaker out. The MAX 250's angled baffle design directs your sound right where you need it, while its lightweight construction and efficient power amp ensure maximum portability. Create the perfect bass guitar tone Achieving chest-thumping bass guitar tone is easy with the MAX 250. Sculpt your sound to perfection with a 3-band EQ. Then put your own sonic stamp on it with Overdrive, Contour, Mid Shift, and Bright controls. Drench your playing in ear-popping harmonics and subharmonics with the MAX 250's Kosmos-C bass enhancement. You also get Peavey's acclaimed DDT speaker protection technology that's ideal for slapping and other loud playing scenarios. Loads of player-friendly features It's easy to build your bass rig around the MAX 250. An external speaker out makes constructing a solid-sounding bass amp stack easy. A bass-specific chromatic tuner prevents an out-of-tune bass from wrecking your performance. You also get an effects loop for integrating your pedals and external processors. Beyond that, its angled baffle design directs your sound right where you want it — no need to tilt your amp back. The bassists here at Absolute Pro Music appreciate the Peavey MAX 250's player-friendly features. Lightweight and portable The MAX 250 was designed with portability in mind. In fact, its power-to-weight ratio is downright impressive! And how did Peavey achieve this? For starters, they built this bass combo amp out of lightweight woods. They also utilized an efficient power amplifier. Every aspect of its design maximizes its portability. Actually, the MAX 250 so lightweight that you won't mind not having a roadie! Peavey MAX 250 Bass Combo Amp Features: 250-watt, 1 x 15" bass combo amp 3-band EQ provides ample sound sculpting Overdrive, Contour, Mid Shift, and Bright controls provide further tone shaping Kosmos-C bass enhancement imparts harmonics and subharmonics for maximum impact and tone Clip-limiting DDT tames your dynamics and protects your speakers Effects loop makes integrating your pedals and external processors a breeze External speaker out for expanding your rig Bass-specific chromatic tuner Angled baffle design directs your sound right where you need it Lightweight construction and efficient power amp ensure maximum portability Tech Specs Type: Solid State Number of Channels: Single Total Power: 250W Speakers: 1 x 15" EQ: 3-band EQ Inputs: 2 x 1/4" (active, passive), 1 x 1/8" (aux) Outputs: 1 x XLR (direct out), 1 x speakON Headphones: 1 x 1/8" Effects Loop: Yes Footswitch I/O: 1 x 1/4" (overdrive, mute) Footswitch Included: No Cooling System: Internal Fan, Rear Air Vent Power Source: Standard IEC AC cable Height: 22.8" Width: 19.4" Depth: 16.2" Weight: 44.4 lbs. ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Peavey MAX 150 1x12" 150-watt Bass Combo Amp+ Free Mr Dj Instrument Cable+Phone Holder 150W, 1-channel, Solid-state, 1x12" Bass Combo Amplifier with 3-band EQ, Overdrive, Contour, Mid Shift, Bright, Kosmos-C, DDT Speaker Protection, Effects Loop, Speaker Out, and Tuner - Black Tailor-made for Performing Bassists The Peavey MAX 150's feature-rich design was tailor-made for performing bassists. This 150-watt bass combo amp includes plenty of onboard sound shaping, with a 3-band EQ and Overdrive, Contour, Mid Shift, and Bright controls. Kosmos-C bass enhancement imparts harmonics and subharmonics for maximum impact and tone. Clip-limiting DDT tames your dynamics and protects your speakers. Integrating your pedals and external processors is a breeze, thanks to the MAX 150's effects loop. Expanding your rig is just as easy, courtesy of the MAX 150's speaker out. The MAX 150's angled baffle design directs your sound right where you need it, while its lightweight construction and efficient power amp ensure maximum portability. Create the perfect bass guitar tone Achieving chest-thumping bass guitar tone is easy with the MAX 150. Sculpt your sound to perfection with a 3-band EQ. Then put your own sonic stamp on it with Overdrive, Contour, Mid Shift, and Bright controls. Drench your playing in ear-popping harmonics and subharmonics with the MAX 150's Kosmos-C bass enhancement. You also get Peavey's acclaimed DDT speaker protection technology that's ideal for slapping and other loud playing scenarios. Loads of player-friendly features It's easy to build your bass rig around the MAX 150. An external speaker out makes constructing a solid-sounding bass amp stack easy. A bass-specific chromatic tuner prevents an out-of-tune bass from wrecking your performance. You also get an effects loop for integrating your pedals and external processors. Beyond that, its angled baffle design directs your sound right where you want it — no need to tilt your amp back. The bassists here at Absolute Pro Music appreciate the Peavey MAX 150's player-friendly features. Lightweight and portable The MAX 150 was designed with portability in mind. In fact, its power-to-weight ratio is downright impressive! And how did Peavey achieve this? For starters, they built this bass combo amp out of lightweight woods. They also utilized an efficient power amplifier. Every aspect of its design maximizes its portability. Actually, the MAX 150 is so lightweight that you won't mind not having a roadie! Peavey MAX 150 Bass Combo Amp Features: 150-watt, 1 x 12" bass combo amp 3-band EQ provides ample sound sculpting Overdrive, Contour, Mid Shift, and Bright controls provide further tone shaping Kosmos-C bass enhancement imparts harmonics and subharmonics for maximum impact and tone Clip-limiting DDT tames your dynamics and protects your speakers Effects loop makes integrating your pedals and external processors a breeze External speaker out for expanding your rig Bass-specific chromatic tuner Angled baffle design directs your sound right where you need it Lightweight construction and efficient power amp ensure maximum portability Tech Specs Type: Solid State Number of Channels: Single Total Power: 150W Speakers: 1 x 12" EQ: 3-band EQ Inputs: 2 x 1/4" (active, passive), 1 x 1/8" (aux) Outputs: 1 x XLR (direct out), 1 x speakON Headphones: 1 x 1/8" Effects Loop: Yes Footswitch I/O: 1 x 1/4" (overdrive, mute) Footswitch Included: No Power Source: Standard IEC AC cable Height: 19" Width: 16.5" Depth: 14.2" Weight: 29.2 lbs. ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Peavey MAX 158 1x8" 20-watt Bass Combo Amp+ Free Mr Dj Instrument Cable+Phone Holder MAX® 158 20-Watt Bass Amp Combo The Max 158 bass combo amp is a 20 watt 1x8" bass practice amp loaded with features, including 1/4" input and Volume with Transtube distortion boost and psyco-acoustic low end enhancement, a 3-band EQ, chromatic tuner and 1/8" jacks for phones output and auxiliary input. The Max 158 also includes Peavey-exclusive DDT speaker protection. Tech Specs 20 Watts RMS into 4 Ohms 8 Inch Speaker Low, Mid, and High EQ Controls Volume Control with Transtube distortion boost Psycho-acoustic low end enhancement 1/8" phone output 1/8" aux input Built-in chromatic tuner DDT Speaker protection Weight Unpacked 18.30 lb (8.3 kg) Weight Packed 21.00 lb (9.525 kg) Width Packed 13"(33.02 cm) Height Packed 17.22" (43.99 cm) Depth Packed 9.45" (24.003 cm) ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Peavey MAX 208 2x8" 200-watt Bass Combo Amp+ Free Mr Dj Instrument Cable+Phone Holder 200W, 1-channel, Solid-state, 2x8" Bass Combo Amp with 3-band EQ, Overdrive, Contour, Mid Shift, Bright, Kosmos-C, DDT Speaker Protection, and Effects Loop - Black Tailor-made for Performing Bassists The Peavey MAX 208's feature-rich design was tailor-made for performing bassists. This 200-watt bass combo amp includes plenty of onboard sound shaping, with a 3-band EQ and Overdrive, Contour, Mid Shift, and Bright controls. Kosmos-C bass enhancement imparts harmonics and subharmonics for maximum impact and tone. Clip-limiting DDT tames your dynamics and protects your speakers. Integrating your pedals and external processors is a breeze, thanks to the MAX 208's effects loop. The MAX 208's angled baffle design directs your sound right where you need it, while its lightweight construction and efficient power amp ensure maximum portability. Create the perfect bass guitar tone Achieving chest-thumping bass guitar tone is easy with the MAX 208. Sculpt your sound to perfection with a 3-band EQ. Then put your own sonic stamp on it with Overdrive, Contour, Mid Shift, and Bright controls. Drench your playing in ear-popping harmonics and subharmonics with the MAX 208's Kosmos-C bass enhancement. You also get Peavey's acclaimed DDT speaker protection technology that's ideal for slapping and other loud playing scenarios. Loads of player-friendly features It's easy to build your bass rig around the MAX 208. You get an effects loop for integrating your pedals and external processors. Beyond that, its angled baffle design directs your sound right where you want it — no need to tilt your amp back. The bassists here at Absolute Pro Music appreciate the Peavey MAX 208's player-friendly features. Lightweight and portable The MAX 208 was designed with portability in mind. In fact, its power-to-weight ratio is downright impressive! And how did Peavey achieve this? For starters, they built this bass combo amp out of lightweight woods. They also utilized an efficient power amplifier. Every aspect of its design maximizes its portability. Actually, the MAX 208 is so lightweight that you won't mind not having a roadie! Peavey MAX 208 Bass Combo Amp Features: 200-watt, 2 x 8" bass combo amp 3-band EQ provides ample sound sculpting Overdrive, Contour, Mid Shift, and Bright controls provide further tone shaping Kosmos-C bass enhancement imparts harmonics and subharmonics for maximum impact and tone Clip-limiting DDT tames your dynamics and protects your speakers Effects loop makes integrating your pedals and external processors a breeze Angled baffle design directs your sound right where you need it Lightweight construction and efficient power amp ensure maximum portability Tech Specs Type: Solid State Number of Channels: Single Total Power: 200W Speakers: 2 x 8" EQ: 3-band EQ Inputs: 2 x 1/4" (active, passive), 1 x 1/8" (aux) Outputs: 1 x XLR (direct out) Headphones: 1 x 1/8" Effects Loop: Yes Footswitch I/O: 1 x 1/4" (overdrive, mute) Footswitch Included: No Power Source: Standard IEC AC cable Height: 23.2" Width: 12.3" Depth: 13.2" Weight: 32.2 lbs. ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Peavey MAX126 10-Watt Bass Amp Combo 6.5" 10-watt Bass Combo Amp+ Free MR DJ Instrument Cable+Phone Holder MAX® 126 10-Watt Bass Amp Combo The MAX 126 bass combo amp is a 10-watt bass practice amp loaded with features that make it ideal for small rehearsals, including TransTube gain boost, multi-band EQ, Peavey exclusive DDT compression, headphone output, and auxiliary input. General Features: 10 Watts RMS into 4 Ohms 6.5" Inch Speaker Low, Mid, and High EQ Controls Volume Control Selectable Vintage Gain Control with patented Transtube circuity 1/4" Headphone Jack 1/4" aux input Built-in chromatic tuner DDT Speaker protection Weight Unpacked 11 lb (4.90 kg) Weight Packed 13 lb (5.9 kg) Width Packed 12.33"(31.3 cm) Height Packed 12.75" (32.36 cm) Depth Packed 8.25" (20.95 cm) ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.