Line Drivers (41)

 Audio Control LC2i 2 Channel Line Out Converter Accubass and Subwoofer Control for amps to your factory system & ACR-1 Dash Remote The LC2i is a compact, two-channel processor with active input circuitry, which allows it to accept speaker-level signals of up to 400 watts per channel from factory-installed source units or amplifiers. It converts them to high-quality preamp signals that can then be directed to after-market processors and amplifiers. As a result, users can enjoy maximum sound quality while maintaining factory volume and steering wheel controls. General Features: Two channels of active speaker level inputs - Accepts 400-watt signals per channel AccuBASS processing for correction of bass roll-off Fixed and variable outputs with discrete-level controls GTO - Signal sensing inputs The 12-Volt trigger that will turn on LC2i Dual amplifier 9.5-volt preamp outs Level matching controls 12 Volt trigger output Input for optional subwoofer level control: AudioControl ACR-1 Dimensions: 6-3/8"W x 3-1/8"D x 1-1/2"H Authorized Internet Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) The LC2i Specifications Maximum speaker level input: 400 watts per channel Maximum Preamp Output: 9.5Vrms / 13V peak Optional Dash Level Control Remote: +0dB / -19dB Frequency response: 10 Hz - 100,000 Hz; ±1dB Total harmonic distortion: 0.01% Signal to Noise ratio: >110dB Input Impedance: 20K ohms Output Impedance: 150 ohms Power draw: 150 mA Recommended fuse rating: 1 Amp Weight: 1 pound What is in the package: LC2i owner's manual Two-Channel line-output converter Quality Control Certificate AudioControl Remote ACR-1 Dash Mount Wired Remote Level Control for Select AudioControl Sound Processors General Features Wired Remote Level Control Mounts on the dash using built-in bracket Detachable mounting plate Works with select AudioControl sound processors Direct replacement remote for the Epicenter Includes 20' power cable Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) What is in the ACR-1package: ACR-1 owner's manual Remote dash mount control 20' RJ-14 cable ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Audio Control MATRIX PLUS 6-Channel Line Driver AudioControl created the MATRIX PLUS six-channel line driver with one goal: to make your car audio system sound better. Modern car stereos boast many features but, in many cases rather low pre-amp outputs, especially at low levels. Turn your stereo to an average volume level, send the signal through a 20-foot cable, and your amps may end up with minimal audio signal resulting in weak sound. The MATRIX PLUS line driver will transform your audio system, equipped with 24 dB of gain, which can increase pre-amp signal levels up to 9.5 volts RMS/13 volts peak. The MATRIX PLUS line driver boosts your system when integrating multimedia and video games or driving dozens of amplifiers. With multiple sources, like video, the MATRIX PLUS level matches the different volume levels, so switching between them is seamless. For SPL vehicles, the internal linking system of the Matrix means that two input channels can drive all six outputs, and each work can drive up to seven amplifiers. General Features: 6-Channel Line Driver Provides up to 24 dB of gain Gray steel chassis with gold-plated RCA jacks 12 dB of Signal Attenuation PFM Subsonic Filter Output Level Controls Balanced Differential Inputs Low Impedance Outputs Voltage Indicator LEDs Optional Remote level control: ACR-1 Weight: 2.25 lbs Dimensions: 8.70" W x 6.70" D x 1.15" H Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) What is in the Matrix Plus package: Matrix Plus owner's manual 6-Channel pre-amp Line Driver ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Diamond Audio LOC22 2-Channel (2 IN / 2 OUT) Line-Output Converter Diamond Audio’s line output converters are your integration ticket for a great sounding audio system. Not only do these provide tremendous output voltage, they provide you with an assortment of various output controls. The load select feature provides flexible compatibility and prevents unwanted system noise. The LOC series line output converters are available as a 2-channel or 4-channel model. General Features  2-Channel (2 IN / 2 OUT) Line-Output Converter Ideal Interface for Adding an Aftermarket Amplifier Single Dial, Precision Matched, Stereo & Level Gain Adjustment Up to 40 Volts RMS High-Level Input Sensitivity Up to 9.5 Volts RMS Low-level RCA Output Selectable 20Ω / 60Ω / 20KΩ Load Input Impedance Selectable GND / ISO / 200Ω Ground Isolation Bass Boost: 0-12dB Dimensions: 4.53" x 3.86" x 0.94" / 115.1 x 98 x 24 mm Removable Quick Connect with Screw Type Terminal ⚠️Warning This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Cerwin-Vega CVM1 Digital Bass Reconstruction Processor Epicenter Enhancer Equalizer General Features: Vega Series Digital Car Audio Bass Enhancer 15V RMS Maximum Input Level 13.2V Peak Maximum Output Level Bass Driver Bass Equalization Circuit Dash Mount Remote Control Bass Maximizer Indicator PFM Subsonic Filter Switch Bass Output Control Frequency Response: 10 – 30KHz ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Blaupunkt EP1700X Car Audio Digital Bass Reconstruction Processor with Remote Want your music to have all the bass you Desire?. this product puts back the bass sound that was lost in recording and compressing the signal to make MP3 files. With the EP1700X you will hear loud and low bass that you never knew existed on your music recordings! Dash-mount remote control for pfm subsonic filter & bass level controls makes all music come Alive with full Frequency low bass. Restores the ground-shaking power and pounding bass your subwoofers were meant to put out!. give your subwoofers the signal to go lower and hit harder. Remote level control lets you decide how loud the bass is Relative to the rest of the music. The sub-sonic filter makes sure that the bass you want to hear is all you hear! General Features: PWM High Head Room Power Supply Parametric Bass Boost Variable Bandwidth Adjustment Dash Mount Remote Control LED MAX Bass Indicators Digital Bass Driver/Restoration Processor Delivers maximum bass control Dash remote control included Parametric bass control Balanced input circuitry minimizes induced noise Maximum Speaker Input Level: 400 Watt per channel @ 4 ohms Maximum Preamp Output : 9.5V RMS/ 12V Peak Frequency Response: 10Hz - 100KHz; +/- 1dB Total Harmonic Distortion: 0.01% Signal Noise to Ratio: 110 dB Input Impedance: 20K Ohms Output Impedance 150 Ohms Power Supply: High Headroom PWM Power Draw: 150mA Recommended Fuse Rating: 1 Amp Package Include: Blaupunkt EP1700X ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov·

Blaupunkt EP1700X Car Audio Digital Bass Reconstruction Processor with Remote Want your music to have all the bass you Desire?. this product puts back the bass sound that was lost in recording and compressing the signal to make MP3 files. With the EP1700X you will hear loud and low bass that you never knew existed on your music recordings! Dash-mount remote control for pfm subsonic filter & bass level controls makes all music come Alive with full Frequency low bass. Restores the ground-shaking power and pounding bass your subwoofers were meant to put out!. give your subwoofers the signal to go lower and hit harder. Remote level control lets you decide how loud the bass is Relative to the rest of the music. The sub-sonic filter makes sure that the bass you want to hear is all you hear! General Features: PWM High Head Room Power Supply Parametric Bass Boost Variable Bandwidth Adjustment Dash Mount Remote Control LED MAX Bass Indicators Digital Bass Driver/Restoration Processor Delivers maximum bass control Dash remote control included Parametric bass control Balanced input circuitry minimizes induced noise Maximum Speaker Input Level: 400 Watt per channel @ 4 ohms Maximum Preamp Output : 9.5V RMS/ 12V Peak Frequency Response: 10Hz - 100KHz; +/- 1dB Total Harmonic Distortion: 0.01% Signal Noise to Ratio: 110 dB Input Impedance: 20K Ohms Output Impedance 150 Ohms Power Supply: High Headroom PWM Power Draw: 150mA Recommended Fuse Rating: 1 Amp Package Include: Blaupunkt EP1700X ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov·

Blaupunkt EP01000X Car Audio Digital Bass Reconstruction Epicenter Processor with Remote Want your music to have all the bass you desire? This product removes the bass sound lost in recording and compresses the signal to make MP3 files. With the EP1000XW, you will hear loud and low bass that you never knew existed on your music recordings!Dash-mount remote control for pfm subsonic filter & bass level controls makes all music come Alive with total Frequency low bass. Restores the ground-shaking power and pounding bass your subwoofers were meant to put out! Give your subwoofers the signal to go lower and hit harder. Remote level control lets you decide how loud the bass is Relative to the rest of the music. The sub-sonic filter ensures that the bass you want is all you hear!General Features: PWM High Head Room Power Supply - Parametric Bass Boost Variable Bandwidth Adjustment - Dash Mount Remote Control Digital Bass Driver/Restoration Processor -Delivers maximum bass control Dash remote control included - Parametric bass control Balanced input circuitry minimizes induced noise Maximum Input Level: 15V RMS Maximum Output Level: 13.5V Peak Frequency Response: 10Hz - 20k Hz Total Harmonic Distortion: 0.003% Signal Noise to Ratio: 130 dB Input Impedance: 10K Ohms Output Impedance 150 Ohms Power Supply: High Headroom PWM Power Draw: 150 mA Recommended Fuse Rating: 1 Amp Package Include: Blaupunkt EP1000X ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Blaupunkt EP01000X Car Audio Digital Bass Reconstruction Epicenter Processor with Remote Want your music to have all the bass you desire? This product removes the bass sound lost in recording and compresses the signal to make MP3 files. With the EP1000XW, you will hear loud and low bass that you never knew existed on your music recordings!Dash-mount remote control for pfm subsonic filter & bass level controls makes all music come Alive with total Frequency low bass. Restores the ground-shaking power and pounding bass your subwoofers were meant to put out! Give your subwoofers the signal to go lower and hit harder. Remote level control lets you decide how loud the bass is Relative to the rest of the music. The sub-sonic filter ensures that the bass you want is all you hear!General Features: PWM High Head Room Power Supply - Parametric Bass Boost Variable Bandwidth Adjustment - Dash Mount Remote Control Digital Bass Driver/Restoration Processor -Delivers maximum bass control Dash remote control included - Parametric bass control Balanced input circuitry minimizes induced noise Maximum Input Level: 15V RMS Maximum Output Level: 13.5V Peak Frequency Response: 10Hz - 20k Hz Total Harmonic Distortion: 0.003% Signal Noise to Ratio: 130 dB Input Impedance: 10K Ohms Output Impedance 150 Ohms Power Supply: High Headroom PWM Power Draw: 150 mA Recommended Fuse Rating: 1 Amp Package Include: Blaupunkt EP1000X ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Audio Control The Epicenter & Cerwin-Vega EQ-770 Digital Bass Restoration Processor Bass Booster Expander with Remote & 7-Band Graphic EQ with Parametric E Auxiliary Input Audio Control THE EPICENTER White 2-Channel Concert Series Digital Bass Restoration Processor with Bass Remote Your MP3 player thinks your car stereo is a pair of headphones, so it removes the bass! The Epicenter restores the earth-shaking power and heart-pounding bass your subwoofers crave. Give your subwoofers the juice to go lower and hit harder.  The Epicenter uses a bass circuit to drive your subwoofers lower, grabbing the attention of every eye on the boulevard. General Features: Active Epicenter Series 2 channel digital bass restoration and line output converter Designed to integrate with after-market or factory OEM systems Digital bass restoration restores bass roll-off in factory systems Speaker level inputs Bass/Gain level remote: Yes Signal-Sensing turn-on: Yes Preamp outputs: 1 pair Bass Maximizer circuitry Multiple turn-on options PFM Subsonic Filter bypass option Selectable impedance load: 20, 60, 20k ohms Frequency response: 10 - 100,000 Hz Subsonic filter: 20 Hz, 12/dB octave Signal-to-noise ratio: >130 dB Total harmonic distortion (THD): 0.003% Fuse Rating: 1A x 1  Dimensions: 8-1/16"W x 1-1/4"H x 6-3/4"H Weight: 1.70lbs Authorized Internet Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) What is in the THE EPICENTER package: The Epicenter owner's manual Pre-amp Bass Restoration Processor black Remote dash mount control Cerwin-Vega EQ-770 7-Band Graphic EQ with Parametric E Auxiliary Input Just a heads up, the manufacturer's packaging and manual advertise this product as a parametric EQ. The product has a "graphic equalizer" printed on it, so that is what we are going with. EQ-770 is the most powerful equalizer. This device is equipped with several different rich sound output selections. Use the equalizer in the master channel of your audio to match the low-end, bass to full sound to your mix. Add back brilliant sounds to old digitalized recordings General Features: 7-Band Graphic Equalizer with Auxiliary Input Red illumination Master and subwoofer volume control 3 Sets of up to 7V preamp outputs (front, rear, and subwoofer) Subwoofer frequency and level control Nickel-plated RCA-level inputs Nickel-plated screw terminals Built-in fader control Authorized Internet Dealer 1-year Manufacturer's Warranty Product Specifications: Number of Bands: 7 Signal-to-noise ratio: 90dB Frequency response: 10 - 50000Hz Channel separation: 70dB What is in the EQ-770 package: EQ-770 owner's manual 7-Band Graphic Equalizer Quality Control Certificate ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Cerwin-Vega CVM1 Digital Bass Reconstruction Processor Epicenter Enhancer Equalizer General Features: Vega Series Digital Car Audio Bass Enhancer 15V RMS Maximum Input Level 13.2V Peak Maximum Output Level Bass Driver Bass Equalization Circuit Dash Mount Remote Control Bass Maximizer Indicator PFM Subsonic Filter Switch Bass Output Control Frequency Response: 10 – 30KHz ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Audio Control LC7i 6 Channel Line Out Converter with bass restoration adds aftermarket subs and amps to a factory system & ACR-1 Dash Remote The AudioControl LC7i, six channel active line converter, allows all music lovers, who want a great in-car audio experience, to keep their factory-installed source unit and dramatically improve their system performance. The LC7i delivers amazing sound quality and fixes one of the biggest letdowns of today’s factory systems, weak BASS! Designed for maximum sound quality and enhanced audio performance, the LC7i incorporates AccuBASS™. This patented process automatically corrects for the bass roll-off that is common with many factory-installed audio systems and AudioControl’s unique and exclusive AccuBASS™ circuitry maintains and restores the Bass as the volume is turned up, improving the audio performance. The LC7i allows the flexibility of powering the audio signals downstream to single or multiple factory amps maximizing sound quality & achieving high output at a great price. In addition, the LC7i is designed to fit into a compact chassis allowing an easy & flexible factory system upgrade in today’s space constrained vehicles. The ACR-1 dash remote (sold separately) allows the user to control the level of the low-frequency output. Add remote level control for your AudioControl processor or amplifier. This is the replacement remote for the Epicenter. Comes with a 20-foot cable and removable mounting enclosure (for custom dash installations).s. General Features: Six Input and Output Channels 6 Speaker Level Inputs - Can Accept 400-Watt Signals! Signal sensing inputs GTO (Great Turn-On) Circuit Internal Channel Summing AutoMode inputs Level matching controls 12-volt trigger output Line Output Converter: A device for converting a powered (or amplified) signal into a pre-amp line level (or non-powered) signal Input for optional subwoofer level control: AudioControl ACR-1 Color: Black Weight: 3.0 lbs Size: 7.5" W x 4.72" D x 1.22" H Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) LC7i Specifications: Maximum speaker-level input: 400 watts @ 4 ohms Maximum output level: 8.5Vrms Output gain: ±15 dB Frequency response: 10Hz - 22,000 Hz Total harmonic distortion: 0.01% Input Impedance: 20 Kohms Output Impedance: 150 ohms Power supply: High headroom PWM switching Power draw: 350mA Recommended fuse rating: 2 Amp Remote Trigger Output Current: 1 Amp What is in the LC7i box: 6-Channel line-output converter Instructions/Specs/Warranty (on packaging) Quality Control Certificate AudioControl LC7i owner's manual AudioControl Remote ACR-1 Dash Mount Wired Remote Level Control for Select AudioControl Sound Processors Add remote level control for your AudioControl processor or amplifier. This is the replacement remote for the Epicenter. Comes with a 20-foot cable and removable mounting enclosure (for custom dash installations).s. General Features Wired Remote Level Control Mounts on the dash using built-in bracket Detachable mounting plate Works with select AudioControl sound processors Direct replacement remote for the Epicenter Includes 20' power cable Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) compatible with 6XS ACM-1.300 The Epicenter® Concert Series LC2i LC6i LC7i Overdrive Plus Matrix Plus LC-4.800 LC-6.1200 legacy products supported LC6 LC8 Original Epicenter® (bypass not supported) What is in the ACR-1 package: Remote dash mount control 20' RJ-14 cable. Mounting Instructions on packaging ACR-1 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Audio Control LC7i 6 Channel Line Out Converter with bass restoration adds aftermarket subs and amps to a factory system The AudioControl LC7i, six channel active line converter, allows all music lovers, who want a great in-car audio experience, to keep their factory-installed source unit and dramatically improve their system performance. The LC7i delivers amazing sound quality and fixes one of the biggest letdowns of today’s factory systems, weak BASS! Designed for maximum sound quality and enhanced audio performance, the LC7i incorporates AccuBASS™. This patented process automatically corrects for the bass roll-off that is common with many factory-installed audio systems and AudioControl’s unique and exclusive AccuBASS™ circuitry maintains and restores the Bass as the volume is turned up, improving the audio performance. The LC7i allows the flexibility of powering the audio signals downstream to single or multiple factory amps maximizing sound quality & achieving high output at a great price. In addition, the LC7i is designed to fit into a compact chassis allowing an easy & flexible factory system upgrade in today’s space constrained vehicles. The ACR-1 dash remote (sold separately) allows the user to control the level of the low-frequency output. Add remote level control for your AudioControl processor or amplifier. This is the replacement remote for the Epicenter. Comes with a 20-foot cable and removable mounting enclosure (for custom dash installations).s. General Features: Six Input and Output Channels 6 Speaker Level Inputs - Can Accept 400-Watt Signals! Signal sensing inputs GTO (Great Turn-On) Circuit Internal Channel Summing AutoMode inputs Level matching controls 12-volt trigger output Line Output Converter: A device for converting a powered (or amplified) signal into a pre-amp line level (or non-powered) signal Input for optional subwoofer level control: AudioControl ACR-1 Color: Black Weight: 3.0 lbs Size: 7.5" W x 4.72" D x 1.22" H Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) LC6i Specifications: Maximum speaker-level input: 400 watts @ 4 ohms Maximum output level: 8.5Vrms Output gain: +/-12 dB Frequency response: 10Hz-22kHz Total harmonic distortion: 0.01% Input Impedance: 20K Ohms Output Impedance: 150 ohms Power supply: High headroom PWM switching Power draw: 350mA Recommended fuse rating: 2 Amp Remote Trigger Output Current: 1 Amp What is in the box: 6-Channel line-output converter Instructions/Specs/Warranty (on packaging) Quality Control Certificate AudioControl LC7i owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

 Audio Control LC2i 2 Channel Line Out Converter Accubass and Subwoofer Control for amps to your factory system & ACR-1 Dash Remote The LC2i is a compact, two-channel processor with active input circuitry, which allows it to accept speaker-level signals of up to 400 watts per channel from factory-installed source units or amplifiers. It converts them to high-quality preamp signals that can then be directed to after-market processors and amplifiers. As a result, users can enjoy maximum sound quality while maintaining factory volume and steering wheel controls. General Features: Two channels of active speaker level inputs - Accepts 400-watt signals per channel AccuBASS processing for correction of bass roll-off Fixed and variable outputs with discrete-level controls GTO - Signal sensing inputs The 12-Volt trigger that will turn on LC2i Dual amplifier 9.5-volt preamp outs Level matching controls 12 Volt trigger output Input for optional subwoofer level control: AudioControl ACR-1 Dimensions: 6-3/8"W x 3-1/8"D x 1-1/2"H Authorized Internet Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) The LC2i Specifications Maximum speaker level input: 400 watts per channel Maximum Preamp Output: 9.5Vrms / 13V peak Optional Dash Level Control Remote: +0dB / -19dB Frequency response: 10 Hz - 100,000 Hz; ±1dB Total harmonic distortion: 0.01% Signal to Noise ratio: >110dB Input Impedance: 20K ohms Output Impedance: 150 ohms Power draw: 150 mA Recommended fuse rating: 1 Amp Weight: 1 pound What is in the package: LC2i owner's manual Two-Channel line-output converter Quality Control Certificate ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Audio Control THE EPICENTER 2-Channel Concert Series Digital Bass Restoration Processor with Bass Remote Your MP3 player thinks your car stereo is a pair of headphones, so it removes the bass! The Epicenter restores the earth-shaking power and heart-pounding bass your subwoofers crave. Give your subwoofers the juice to go lower and hit harder.  The Epicenter uses a bass circuit to drive your subwoofers lower, grabbing the attention of every eye on the boulevard. General Features: Active Epicenter Series 2 channel digital bass restoration and line output converter Designed to integrate with after-market or factory OEM systems Digital bass restoration restores bass roll-off in factory systems Speaker level inputs Bass/Gain level remote: Yes Signal-Sensing turn-on: Yes Preamp outputs: 1 pair Bass Maximizer circuitry Multiple turn-on options PFM Subsonic Filter bypass option Selectable impedance load: 20, 60, 20k ohms Frequency response: 10 - 100,000 Hz Subsonic filter: 20 Hz, 12/dB octave Signal-to-noise ratio: >130 dB Total harmonic distortion (THD): 0.003% Fuse Rating: 1A x 1  Dimensions: 8-1/16"W x 1-1/4"H x 6-3/4"H Weight: 1.70lbs Authorized Internet Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) What is in the THE EPICENTER package: The Epicenter owner's manual Pre-amp Bass Restoration Processor black Remote dash mount control ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Cerwin-Vega EQ-770 7-Band Graphic EQ with Parametric E Auxiliary Input Just a heads up, the manufacturer's packaging and manual advertise this product as a parametric EQ. The product itself has a "graphic equalizer" printed on it, so that is what we are going with. EQ-770 is the most powerful equalizer. This device is equipped with several different rich sound output selections. Use the equalizer in the master channel of your audio to match the low end, bass to full sound to your mix Add back brilliant sounds to old digitalized recordings General Features: 7-Band Graphic Equalizer with Auxiliary Input Red illumination Master and subwoofer volume control 3 Sets of up to 7V preamp outputs (front, rear, and subwoofer) Subwoofer frequency and level control Nickel-plated RCA level inputs Nickel-plated screw terminals Built-in fader control Authorized Internet Dealer 1-year Manufacturer's Warranty Product Specifications: Number of Bands: 7 Signal-to-noise ratio: 90dB Frequency response: 10 - 50000Hz Channel separation: 70dB What is in the EQ-770 package: 7-Band Graphic Equalizer Instructions/Specs/Warranty (on packaging) Quality Control Certificate Cerwin Vega EQ-770 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov