

AudioControl
Audio Control EQL 2-Channel Trunk Mount Dual Bandwidth Graphic Equalizer and Pre-Amp
$249.99
$499.98
Audio Control EQL 2-Channel Trunk Mount Dual Bandwidth Graphic Equalizer and Pre-Amp
The EQL works wonders with any 2 channel audio system: From existing factory installed setups to custom audiophile-grade systems. Level-matching circuitry allows connection to either preamp-level or speaker-level inputs. The EQL also features thirteen-band, dual-bandwidth equalization and a Programmable Frequency Match (PFM) filter for precise bass control.The dual bandwidth design of the EQL concentrates more control in the lower bass frequencies where the interior of an automobile causes problems. The higher frequency controls are spaced on octave centers to give you complete control up to 16,000 Hz. No simple dash-mount equalizer gives you this kind of flexibility.
General Features:
Trunk Mount Equalizer and Pre-Amp
6 Band, 1/2 Octave Bass EQ
7 Band, 1 Octave Equalizer
Programmable Frequency Match (PFM) Subsonic Filter
Line and Speaker Level Inputs
Balanced Inputs
Input and Output Level Matching Controls
Color: Black Blue
Weight: 3 lbs
Dimensions: 1.25" H x 8.9" L x 6.9" W
Frequency Response: 10 Hz to 20 kHz ± 1 dB
Total Harmonic Distortion (THD): 0.005%
Signal to Noise Ratio (SNR): 110 dB at full output
Maximum Output Level: 7.5 volts rms
Input Gain: ± 18 dB
PFM Filter Slope: 18 dB per octave
PFM Frequency: Programmable 15 to 100 Hz
Factory Shipped @ 33Hz
Power Supply: Variable isolation. Transformer switching supply
Fuse Rating: 2 amps
Balanced Input Yes
Ground Isolation Jumpers: Yes
Country of origin: USA
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.


AudioControl
Audio Control ACM-2.300 300W RMS ACM Series 2 ohm Stable 2-Channel Class-D Amplifier
$359.99
$719.98
Audio Control ACM-2.300 300W RMS ACM Series 2 ohm Stable 2-Channel Class-D Amplifier
General Features:
AudioControl ACM Series ACM-2.300
Class-D 2 ohm Stable 2-Channel Amplifier
RMS Power Rating: Small footprint for flexible mounting options
GTO Signal Sense turns on the amp when the signal is detected from the factory amp or stereo
Patented AccuBASS processing restores bass
Pulse Width Modulated MOSFET power supply
LED power (green) and protect (red) indicators
Soft start turn-on
Mono channel operation
Speaker-level (high-level) inputs
3-way protection circuitry (thermal, overload, and short speaker protection)
Heavy-duty aluminum alloy heat-sink
Input sensitivity:
Frequency Response: 10 - 22000Hz
Total Harmonic Distortion (THD): <.01%
Signal Noise Ratio: 102 dB
Linkwitz-Riley Crossover
Fuse Rating: 30A x 1
8 gauge power and ground wiring is recommended for installation.
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.


Diamond Audio
Diamond Audio HXP104 HEX 10" 700W RMS 4-Ohm Subwoofer
$799.99
$1,599.98
Diamond Audio HXP104 HEX 10" 700W RMS 4-Ohm Subwoofer
For the ultimate sounding subwoofer, look no further than HEX PRO series. Equipped with our patented TDXTM Technology (Thermal Dyne Extreme), the motor structure is integrated into the robust cast basket aluminum frame for optimal thermal heat dissipation resulting in longer play at SPL levels, greater longevity and superior reliability!
GENERAL INFORMATION
4Ω Impedance
700W RMS,1400W MAX
Dual Voice Coil
Mounting Diameter: 9.4 Inches / 239mm
Mounting Depth: 7.5 inches / 191mm
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.


Diamond Audio
Diamond Audio HXP102 HEX 10" 700W RMS 2-Ohm Subwoofer
$799.99
$1,599.98
Diamond Audio HXP102 HEX 10" 700W RMS 2-Ohm Subwoofer
For the ultimate sounding subwoofer, look no further than HEX PRO series. Equipped with our patented TDXTM Technology (Thermal Dyne Extreme), the motor structure is integrated into the robust cast basket aluminum frame for optimal thermal heat dissipation resulting in longer play at SPL levels, greater longevity and superior reliability!
GENERAL INFORMATION
2Ω Impedance
700W RMS,1400W MAX
Dual Voice Coil
Mounting Diameter: 9.4 Inches / 239mm
Mounting Depth: 7.5 inches / 191mm
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.


Diamond Audio
Diamond Audio DXM1000.6D 6-Channel Full Range Class D WaterPROof Amplifier
$879.99
$1,759.98
Diamond Audio DXM600.2D DXM 2-Channel Full Range Class D WaterPRO
IPX67 RATED Waterproof multi-layer circuit boards for marine applications - Balanced differential inputs for noise-free operation regardless of the source - Full-range digital Class D technology with Direct FET power MOSFET output stage - 12dB per octave adjustable crossovers and phase control for system tuning. Selectable 3 option Auto Turn-On Mode circuit designed to work with ANY OEM head-unit, simplifies installation.
GENERAL INFORMATION
170W x 6CH @ 2Ω / 110W x 6CH @ 4Ω / 340W x 3CH @ 4Ω Bridged RMS Power Output
Input Sensitivity: 0.2-10 Volt
Crossover Filter : 40-400Hz, 12dB Per Octave Slope
Frequency Response: 10-33KHz
Selectable X-Over: LPF / FULL / HPF
Selectable 2CH / 6CH Input Modes
Dimensions: 11.76” x 4.33” x 1.73” / 298.6 x 110 x 44.0 mm
RCA Input & Speaker & Power Supply Harness Kits and Remote Bass Knob Included
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.


Diamond Audio
Diamond Audio DXM1200.1D DXM Monoblock Class D Waterproof Amplifier
$679.99
$1,359.98
Diamond Audio DXM600.2D DXM 2-Channel Full Range Class D WaterPRO
IPX67 RATED Waterproof multi-layer circuit boards for marine applications - Balanced differential inputs for noise-free operation regardless of the source - Full-range digital Class D technology with Direct FET power MOSFET output stage - 12dB per octave adjustable crossovers and phase control for system tuning. Selectable 3 option Auto Turn-On Mode circuit designed to work with ANY OEM head-unit, simplifies installation.
GENERAL INFORMATION
1200W x 1CH @ 1Ω / 800W x 1CH @ 2Ω / 500W x 1CH @ 4Ω RMS Power Output
Input Sensitivity: 0.2-10 Volt
Crossover Filter : 40-250Hz (LPF), 24dB Per Octave Slope
Subsonic Filter: 10-55Hz
Bass Boost: 0-18dB
Variable Phase Adjustment
Frequency Response: 10-350Hz
Dimensions: 11.76” x 4.33” x 1.73” / 298.6 x 110 x 44.0 mm
RCA Input & Speaker & Power Supply Harness Kits and Remote Bass Knob Included
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.


Diamond Audio
Diamond Audio DXM800.4D DXM 4-Channel Full Range Class D WaterPROof Amplifier
$649.99
$1,299.98
Diamond Audio DXM600.2D DXM 2-Channel Full Range Class D WaterPRO
IPX67 RATED Waterproof multi-layer circuit boards for marine applications - Balanced differential inputs for noise-free operation regardless of the source - Full-range digital Class D technology with Direct FET power MOSFET output stage - 12dB per octave adjustable crossovers and phase control for system tuning. Selectable 3 option Auto Turn-On Mode circuit designed to work with ANY OEM head-unit, simplifies installation.
GENERAL INFORMATION
200W x 4CH @ 2Ω / 125W x 4CH @ 4Ω / 400W x 2CH @ 4Ω Bridged RMS Power Output
Input Sensitivity: 0.2-10 Volt
Crossover Filter : 40-400Hz, 12dB Per Octave Slope
Frequency Response: 10-33KHz
Selectable X-Over: LPF / FULL / HPF
Selectable 2CH / 4CH Input Modes
Dimensions: 11.76” x 4.33” x 1.73” / 298.6 x 110 x 44.0 mm
RCA Input & Line-Out, Speaker,Power Supply Harness Kits Included
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Diamond Audio
Diamond Audio DXM600.2D DXM 2-Channel Full Range Class D WaterPROof Amplifier
$499.99
$999.98
Diamond Audio DXM600.2D DXM 2-Channel Full Range Class D WaterPRO
IPX67 RATED Waterproof multi-layer circuit boards for marine applications - Balanced differential inputs for noise-free operation regardless of the source - Full-range digital Class D technology with Direct FET power MOSFET output stage - 12dB per octave adjustable crossovers and phase control for system tuning. Selectable 3 option Auto Turn-On Mode circuit designed to work with ANY OEM head-unit, simplifies installation.
GENERAL INFORMATION
300W x 2CH @ 2Ω / 200W x 2CH @ 4Ω / 600W x 1CH @ 4Ω Bridged RMS Power Output
Input Sensitivity: 0.2-10 Volt
Crossover Filter : 40-400Hz, 12dB Per Octave Slope
Frequency Response: 10-33KHz
Selectable X-Over: LPF / FULL / HPF
Bass Boost: 0-18dB
Dimensions: 9.5” x 4.33” x 1.73” / 241.6 x 110 x 44.0 mm
RCA Input & Line-Out, Speaker,Power Supply Harness Kits Included
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.


Diamond Audio
Diamond Audio MICRO88U 1000W RMS 8-Channel Full Range Class D Amplifier
$949.99
$1,899.98
Diamond Audio MICRO82U 2-Channel 500W RMS Full Range Class D Amplifier
GENERAL INFORMATION
Diamond Audio continues to break new dimensions by introducing the MICRO8U series of amplifiers for 2018. Following in the footsteps of the highly popular MICRO series amplifiers, the big-brother MICRO8U series packs more power and performance!
115W x 8CH @ 2Ω / 75W x 8CH @ 4Ω / 200W x 4CH @ 4Ω Bridged RMS Power Output
Input Sensitivity: 0.2-10 Volt
Crossover Filter :
Fixed 75Hz (HPF) 12dB Per Octave Slope ( CH1/CH2/CH3/CH4 )
40-400Hz, 12dB Per Octave Slope ( CH5/CH6/CH7/CH8 )
Frequency Response: 10-33KHz
Selectable 2CH / 8CH Input Modes
Dimensions: 11.44″ x 4.0″ x 1.6″ (290.5 x 103 x 40.6 mm)
Disconnected RCA Input & Speaker Output Harness Kits Included
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.


Diamond Audio
Diamond Audio MICRO82U 2-Channel 500W RMS Full Range Class D Amplifier
$479.99
$959.98
Diamond Audio MICRO82U 2-Channel 500W RMS Full Range Class D Amplifier
GENERAL INFORMATION
Diamond Audio continues to break new dimensions by introducing the MICRO8U series of amplifiers for 2018. Following in the footsteps of the highly popular MICRO series amplifiers, the big-brother MICRO8U series packs more power and performance!
250W x 4CH @ 2Ω / 150W x 2CH @ 4Ω / 500W x 1CH @ 4Ω Bridged RMS Power Output
Input Sensitivity: 0.2-10 Volt
Crossover Filter: 40-400Hz (LPF), 24dB Per Octave Slope
Frequency Response: 10-33KHz
Selectable REM / VOX / DC Turn-On Modes
Dimensions: 9” x 4.06” x 1.52” / 228.6 x 103 .124x 38.608 mm
Remote Bass Knob Included
Disconnected RCA Input Harness Kits Included
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Diamond Audio
Diamond Audio DES400.2D 2-Channel Full Range Class D Amplifier
$369.99
$739.98
Diamond Audio DES400.2D 2-Channel Full Range Class D
Diamond Elite DES series amplifiers have been our workhorse since their introduction last year when it was engineered and designed from the ground up. Smaller than the previous generation and constructed with the same footprint dimensions for all models, these amplifiers have been engineered to sound even more dynamic and to deliver optimal rated power at all impedance levels! A ll Diamond Elite DES series amplifiers feature various switched speaker level turn on options (VOX/DC Offset/REM), utilize the latest digital chipset technology, and provides installation flexibility and all the controls necessary to fine-tune and improve the sound quality of any car audio system.
General Features:
120 W x 4 @ 4Ω
185 W x 4 @ 2Ω
370 W x 2 @ 4Ω bridged
S/N: ≤ 95 dBA / THD: .06%
Dimensions: (Remote Included): 8.75" x 7.67" x 2" (222 x 195 x 51.5 mm)
Anodized Extruded Aluminum Heat Sink Provides Superior Thermal Performance
4-Layer PCB Board with Balanced Differential Inputs
Full Range Class D IR Chipset
"SNAP" Capacitors used Throughout the Circuit
Audiophile Grade High Tolerance Components
Spring Steel FET Clips Provide a Cleaner Board Design
Illuminated Logo / Fully Concealed Mounting
Output Clip Indicators for Precise Set-Up
Fine Tuned Fully Variable Crossovers and Phase Control
Top Mounted Controls for Convenient Amplifier Adjustment
⚠️Warning:This product can expose you to, known to the State of California, to cause cancer For more information, go to P65Warnings.ca.


Diamond Audio
Diamond Audio HX400.2 2-Channel 400W RMS Full Range Class D Amplifier
$569.99
$1,139.98
Diamond Audio HX400.2 2-Channel 400W RMS Full Range Class D Amplifier
Audiophile-grade high tolerance components - 4-layer PCB board with balanced differential inputs - full-range digital class-d Ir chip sets - fine-tuned variable - crossover and phase control- top mounted controls for convenient amplifier adjustment turn to hex series amplifiers for superior sound quality and unparalleled power for the ultimate audiophile system set up. Composed of high-tolerance grade components and tuning adjustments to fit your listening desires, hex series amplifiers are the choice for those who expect the best!
General Features:
Amplifier 2 Channel
RMS Power(2Ω) 350 W X 2
RMS Power (4Ω) 200 W X 2
RMS Bridge (mono 2Ω) N/A
RMS Bridge (mono 4Ω) 700 W X 1
RMS Bridge (stereo 4Ω) N/A
Topology Full-Range Class D
Power Supply Full PWM
Power Supply (Threshold) 10.0VDC – 17.0VDC
Idle Current (0.7A)
Distortion - THD (1KHz@4Ω) 0.06%
Distortion - S/N Ratio (A weight @ 1W) -80dBA
Distortion - S/N Ratio (A weight @ FP) -95dBA
Input Sensitivity Low 200mV – 5.0V
Input Sensitivity High N/A
Input Impedance - Low Input Level 20 KΩ
Input Impedance - High Input Level N/A
Output Impedance 0.011Ω
Damping Factor (50Hz@4Ω) >250
Bandwidth (-3dB) 10Hz-35kHz
Crossover (-12 dB/ Oct) Variable High-Pass 40Hz - 400Hz
Crossover (-12 dB/ Oct) Variable Low-Pass 40Hz - 400Hz
Crossover (-12 dB/ Oct) Variable Sub-Sonic N/A
FUSE Ratings - ATC 25A X 2
Dimension - Length x Width x Height - Inches(mm) 8.75″ x7.67″ x 2″ (222 x 195 x 51.5 mm)
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.


Power Acoustik
Power Acoustik VA2-1400D Vertigo Series 2Ch Full Range Amplifier
$64.99
$109.98
Power Acoustik VA2-1400D Vertigo Series 2Ch Full Range Amplifier
Vertigo amplifiers are the next step in performance and value. Taking advantage of our tried and true class A/B full range and improved efficiency class D monoblock platforms, Vertigo amplifiers continue down the road of reliability and longevity you know well.
General Features:
2-ohm Stereo & 4-ohm Bridged Class A/B Full Range
MOSFET Power Supply w/ Audiophile Grade IRTM Transistors
Military Grade SMT PCB Maintains Dynamic Performance
Direct Short, Thermal, & Overload Circuits Protect Amplifier
200mV-6V Low Level/RCA Input w/ Bridged Operation Outputs
High-Level Input w/ Signal Sense Auto Turn-on
Barrier Strip Wire Terminals, 4g Power & 8g Speaker Outputs
Variable 12dB High Pass, Low Pass, & Subsonic Crossovers
12dB Bass Boost Increases Low Octave Harmonics
Amplifier Dimensions (2″H x 8.75″W x 8.5″L)
1 year manufactures warranty
⚠️Warning:For cancer and Reproductive Harm, go to www.P65Warnings.ca.gov.


Alpine
Alpine BBX-T600 300W 2 Channel Amplifier with Pair of S-W12D4 12 Inch Subwoofers
$516.86
Alpine BBX-T600 300W 2 Channel Amplifier with Pair of S-W12D4 12 Inch SubwoofersThis new BBX amplifier gives you Alpine power performance at an amazing price. And they’re designed to fit easily in virtually any system. Performance With Bass EQ, you can maximize the performance of your system and get even more powerful bass.The S-W12D4 12" sub can handle up to 600 watts RMS, so you can drive it hard without any worries. The tough Kevlar treated cone stays rigid under pressure, while its rubber High Amplitude Multi-Roll (HAMR) surround enables maximum excursion for impressive performance.Product Highlights:
Class-A/B 2-ohm Stable 2-Channel Amplifier
Thermal Management Control
DC-DC PWM Power Supply
Pulse Width Modulated MOSFET power supply
Current Protection: Over-Current, Over-Voltage, and Thermal Protection
Green/red Status LED
Heavy-duty aluminum alloy heat-sink
Power Handling:
Total Max Power: 300W
Per Channel into 4ohms (≤1%THD+N): 2 x 50W
Per Channel into 2ohms (≤1%THD+N): 2 x 70W
Bridged into 4ohms (≤1%THD+N): 1 x 130W
Frequency Response: 5 Hz - 50 kHz (+ 0,-3 dB)
Power Requirements: 14.4 V DC (11 V to 16 V)
Input Sensitivity: 0.2 - 8.0 V
Speaker Impedance: 4 or 2 Ω
Signal to Noise: S/N Ratio 95 dB
Variable high-pass filter: 80 - 1200 Hz
Variable low-pass filter: 50 - 500 Hz
Alpine 2 Pack S-W12D4 S-Series 12" Subwoofer:
12" subwoofer with dual 4-ohm voice coils
Kevlar reinforced pulp cone with HAMR Santoprene rubber surround
Max RMS Power Capacity: 600W RMS (300 watts per coil)
Peak Power Capacity: 1800W Peak Power
Frequency response: 26-200 Hz
Top-mount depth: 5-1/16"
This new BBX amplifier gives you Alpine power performance at an amazing price. And they’re designed to fit easily in virtually any system. Performance With Bass EQ, you can maximize the performance of your system and get even more powerful bass.
⚠️Warning:Cancer and Reproductive Harm, go to www.P65Warnings.ca.gov.


Alpine
Alpine BBX-T600 600W Max 2-ohm 2 Channel Class A/B Amplifier + Absolute RCA17 17' RCA
$134.95
$259.90
Alpine BBX-T600 600W Max 2-ohm 2 Channel Class A/B Amplifier + Absolute RCA17 17' RCA
Alpine BBX-T600 600W Max BBX Series 2-ohm Stable 2 Channel Class A/B Amplifier
This new BBX amplifier gives you Alpine power performance at an amazing price. And they are designed to fit easily in virtually any system. This amp delivers high output power and exceptional performance for their class. A great way to expand your sound system on a limited budget. These two filters let you set the frequency points for the high, mid, and bass ranges to match your speakers and ensure optimum efficiency. With Bass EQ, you can maximize the performance of your system and get even more powerful bass.
General Features:
Alpine BBX-T600
Class-A/B 2-ohm Stable 2-Channel Amplifier
50 Watts @ 4 Ohm x 2 Channel
70 Watts @ 2 Ohm x 2 Channel
130 Watts @ 4 Ohm x 1 Channel Bridged
Total power output: 600 watts
Pulse Width Modulated MOSFET power supply
LED power (green) and protect (red) indicators
Soft start turn-on
Two or Mono channel operation
One pair of preamp outputs to connect multiple amplifiers
3-way protection circuitry (thermal, overload, and speaker short protection)
Dual speaker terminals simplify the hookup of multiple speakers
Heavy-duty aluminum alloy heat-sink
Input sensitivity: .2V - 8V
Frequency Response: 5 - 50000 Hz
Total Harmonic Distortion (THD): <1%
Signal Noise Ratio: 95dB
Variable high-pass filter: 80 - 1200 Hz
Variable low-pass filter: 50 - 500 Hz
Variable Bass Boost: 0 to +12 dB bass boost
Fuse Rating: 20A x 1
Dimensions: 9.84"W x 9.44"L x 2"H
Authorized Internet Dealer
1-year Manufacturer's Warranty
Weight: 5.00lbs
What's in the BBX-T600 package:
BBX-T600 owner's manual
Two Channel amplifier
Owner's manual (English/ French/ Spanish)
Alpine Verification Certificate
Warranty information
Power supply note
Online product registration information
⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov