Under Car Seat Powered Subwoofers (16)

Power Acoustik PUB-8L Powered Enclosure w/ 8″ Subwoofer & RGB LED Lighting General Features: Powder Coated Diecast Aluminum Enclosure RGB LED Lighting Floods the Subwoofer with Light 600w Class D Monoblock Subwoofer Amplifier Variable 50-150Hz 12dB Low Pass Crossover Variable 0-12dB Bass Boost Centered at 45Hz 0-1800 Signal Phase Switch for Dynamic Response High Level Input on Quick Disconnect Harness Optional High Level Signal Sense Auto-Turn On 200m V-6V Stereo Low Level RCA Input 8g Power/Ground Wire Input Terminal Dash-Mount Remote Control Included 9.50”w x 3.375”h x 12.25”L Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine PSS-22WRA Jeep Wrangler JK Unlimited Weather Resistant Upgrade SPV-65X-WRA x 2, KTA-30F-WRA, KTA-30M-WRA, SBV-10-WRA Good times in your Wrangler Unlimited are about to get better. Alpine's Restyle PSS-22WRA speaker system takes the guesswork out of installation with nine direct-fit speakers and power sources perfectly suited for your Jeep Wrangler JK Unlimited (incompatible with premium sound systems). Alpine has also designed this weather-proof system to endure the environmental harshness of life in your Jeep, even when the top is off. Get ready to rock the great outdoors.The soundAlpine supplies everything you need to revitalize the sound in your Wrangler. You'll get two 6-1/2" component systems with 1" dome tweeters for your Jeep's front and soundbar locations. Alpine lets you convert these components to a coaxial design if called for in your JK Unlimited. The included weather-resistant Tough Pack 4-channel amp ups your power for awesome clarity at all volumes — a must for top-down drivers. Alpine also gives you a 10" enclosed under-seat subwoofer and a Tough Pack mono amp for some whoppin' bass. The fitAlpine designed the Restyle line for drivers who want to improve their sound but want to maintain the factory look of their vehicle. The PSS-22WRA sound system upholds this approach by including tweeter mounting gear suitable for various locations. The woofers fit directly into your factory locations, and in the case of the two amps, all wiring is included, complete with factory-compatible plugs. Once the PSS-22WRA system goes in, you won't even know it's there... until you crank up the volume.READ LESSProduct highlights:Compatible with select 2011-18 Jeep Wrangler JK Unlimited models (not compatible with premium sound systems)Package includes:two sets of SPV-65X-WRA 6-1/2" component speakersweather-resistant Tough Pack KTA-30F-WRA 4-channel amplifierweather-resistant Tough Pack KTA-30M-WRA mono amplifier with the remote bass knobSBV-10-WRA 10" enclosed submounting gear, wiring, and connectorsincluded SPV-65X-WRA speakers can be configured for component or coaxial use General Features: Alpine PSS-22WRA Audio Restyle for Jeep Wrangler Unlimited JK Includes speakers, tweeters, a powered subwoofer, and two amplifiers Fully Waterproof Plug-and-Play Package Specifically designed for 2007-2018 four-door Jeep Wrangler Unlimited Vehicles Authorized Internet Dealer compatible with select 2011-18 Jeep Wrangler JK Unlimited models (not compatible with premium sound systems) Package includes: two sets of SPV-65X-WRA 6-1/2" component speakers weather-resistant Tough Pack KTA-30F-WRA 4-channel amplifier weather-resistant Tough Pack KTA-30M-WRA mono amplifier with the remote bass knob SBV-10-WRA 10" enclosed sub mounting gear, wiring, and connectors included SPV-65X-WRA speakers can be configured for component or coaxial use What's in the PSS-22WRA package: SPV-65X-WRA x 2, KTA-30F-WRA, KTA-30M-WRA, SBV-10-WRA ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine PSS-24WRA Complete Audio System for 18-Up Jeep Wrangler & 20-Up Gladiator Compatible Vehicles: 2018 – UP JEEP® WRANGLER, 4DR / NON-AMPLIFIED 2020 – UP JEEP® GLADIATOR, NON-AMPLIFIED TOP-OFF SOUNDYour Jeep® begs for top-off drives, whether cruising down the highway or weaving through trails, so you need a sound system that delivers music for all your adventures. The PSS-24WRA is a 300-watt Complete Sound System Upgrade Package for the four-door, non-amplified 2018—Up Jeep® Wrangler and non-amplified 2020—Up Jeep® Gladiator.COMPLETE PACKAGEGo beyond your wildest expectations for sound with this complete sound upgrade package. The PSS-24WRA has 5-channels of powered sounds that replace your factory system. The package includes two sets of 6.5” weather-resistant mid-bas drivers and 1” weather-resist tweeters that replace the front and rear soundbar factory speakers, an 8” powered, compact subwoofer, and a 4-channel power pack amplifier.TUNED FOR JEEP®The PSS-24WRA sound system is tuned for the unique cabin environment of the 2018 - Up Jeep® Wrangler and 2020 – Up Jeep® Gladiator. The weather-resistant speakers are designed for powerful, top-off performance unhindered by weather, wind, or other noise while driving. The 6.5” mid-bass drivers bring out the full potential of your sound, while the tweeters capture the high frequencies often lost in music reproduction. The 8” compact subwoofer adds deep, accurate bass that grounds your sound system.PLUG-AND-PLAY INSTALLATIONVehicle-specific speaker connectors and pods designed for the 2018 - Up Jeep® Wrangler and 2020 – Up Jeep® Gladiator are included for plug-and-play installation. Tweeter adapter plates use the original factory tweeter locations to remove the guesswork from installation. Vehicle-specific mounting brackets are included to secure the 8” compact subwoofer and 4-channel amplifier under the passenger seat without drilling.SYSTEM COMPATIBILITYThe PSS-24WRA is compatible with the i407-WRA-JL 7-Inch Multimedia Receiver and X409-WRA-JL 9-Inch Weather-Resistant Navigation System with Off-Road Mode. The PSS-24WRA also includes a vehicle-specific T-harness for installation with the factory radio into compatible four-door, non-amplified NEW 2018 – 2020 Jeep® Wrangler and non-amplified 2020 – Up Jeep® Gladiator. General Features: Complete, five-channel powered sound system upgrade package Compatible with four-door, non-amplified 2018 - Up Jeep Wrangler and non-amplified 2020 - Up Jeep Gladiator Also compatible with two-door, non-scissor front seats in 2019 - Up Jeep Wrangler Includes Alpine's SPV-65X-WRA, SPV-65-JLT, PWE-S8, and KTP-445U 180W, 4-channel Power Pack amplifier 120W, 8" powered subwoofer (2x) 6.5" weather-resistant mid-bass drivers (2x) 1" weather-resistant teteron dome tweeters with vehicle-specific connectors and crossovers Vehicle-specific front speaker pods with vehicle-specific connectors Tweeter adapter plates allow for the use of the original factory tweeter locations SPV-65-JLT weather-resistant rear soundbar speaker system Rugged, premium grills designed to emulate the factory look and appeal Vehicle-specific connectors for plug-and-play speaker installation  Utilizes factory bolt locations Durable stamped, steel frame speaker basket design Includes template for mounting Vehicle-specific T-harness for installation with OEM radio into compatible 2018 - Up Jeep Wrangler and 2020 - Up Jeep Gladiator vehicles Vehicle-specific mounting brackets allow the powered sub and amp to be secured Front (SPV-65X-WRA): Power handling: 75 watts RMS (225 watts peak) Frequency response: 65kHz – 22kHz Nominal impedance: 4 ohms Weather-resistant: IP55 Rear (SPV-65-JLT): Power handling: 90 watts RMS (270 watts peak) Frequency response: 50kHz – 22kHz Nominal impedance: 4 ohms Weather-resistant: IP55 Powered Subwoofer (PWE-S8): 120 watts RMS (240 watts peak) Frequency response: 32 - 150Hz Variable low-pass crossover (80-200 Hz) Variable phase control (0-180 degrees) preamp- and speaker-level inputs Four-Channel Power Pack Amplifier (KTP-445U): 45 watts RMS x 4 at 4 or 2 ohms 90 watts RMS x 2 bridged at 4 ohms Selectable high-pass filters (60, 80, or 120 Hz at 12 dB/octave) Switchable RCA or speaker-level inputs Dimensions: 27” L x 18.5” W x 19.5” H Weight: 40lbs Authorized Dealer 1-year Manufacturer's Warranty Note: Not compatible with the factory-equipped subwoofer system What's in the PSS-24WRA package: PSS-24WRA owner's manual This Alpine kit contains five individually packaged items: PWE-S8 Subwoofer KTP-445U Amplifier SPV-65X-WRA 6.5" Component Speakers SPV-65-JLT 6.5" 2-Way Speakers ALP-POD-JLTR Speaker Pods PSU-BKT-JL-R PWE Right Bracket JL PSU-BKT-JL-L PWE Left Bracket JL ALP-HRN-PSU300 PSU Power Harness ALP-THRN-CH2 Chrysler T-Harness CT6 6" Cable Ties PHPSM412 Pan Head Phillips Screw M4x12 SLWM4 M4 Split Lock Washers PHSCR832 8-32 Pan Head Phillips screws PSS-WRA-IM Installation Manual Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine PSS-24WRA Complete Audio System for 18-Up Jeep Wrangler & 20-Up Gladiator Compatible Vehicles: 2018 – UP JEEP® WRANGLER, 4DR / NON-AMPLIFIED 2020 – UP JEEP® GLADIATOR, NON-AMPLIFIED TOP-OFF SOUNDYour Jeep® begs for top-off drives, whether cruising down the highway or weaving through trails, so you need a sound system that delivers music for all your adventures. The PSS-24WRA is a 300-Watt Complete Sound System Upgrade Package for the four-door, non-amplified 2018 – Up Jeep® Wrangler and non-amplified 2020 – Up Jeep® Gladiator.COMPLETE PACKAGEGo beyond your wildest expectations for sound with this complete sound upgrade package. The PSS-24WRA has 5-channels of powered sounds that replace your factory system. The package includes two sets of 6.5” weather-resistant mid-bas drivers and 1” weather-resist tweeters that replace the front and rear soundbar factory speakers, an 8” powered, compact subwoofer, and a 4-channel power pack amplifier.TUNED FOR JEEP®The PSS-24WRA sound system is tuned for the unique cabin environment of the 2018 - Up Jeep® Wrangler and 2020 – Up Jeep® Gladiator. The weather-resistant speakers are designed for powerful, top-off performance unhindered by weather, wind, or other noise while driving. The 6.5” mid-bass drivers bring out the full potential of your sound, while the tweeters capture the high frequencies often lost in music reproduction. The 8” compact subwoofer adds deep, accurate bass that grounds your sound system.PLUG-AND-PLAY INSTALLATIONVehicle-specific speaker connectors and pods designed for the 2018 - Up Jeep® Wrangler and 2020 – Up Jeep® Gladiator are included for plug-and-play installation. Tweeter adapter plates use the original factory tweeter locations to remove the guesswork from installation. Vehicle-specific mounting brackets are included to secure the 8” compact subwoofer and 4-channel amplifier under the passenger seat without drilling.SYSTEM COMPATIBILITYThe PSS-24WRA is compatible with the i407-WRA-JL 7-Inch Multimedia Receiver and X409-WRA-JL 9-Inch Weather-Resistant Navigation System with Off-Road Mode. The PSS-24WRA also includes a vehicle-specific T-harness for installation with the factory radio into compatible four-door, non-amplified NEW 2018 – 2020 Jeep® Wrangler and non-amplified 2020 – Up Jeep® Gladiator. General Features: Complete, five-channel powered sound system upgrade package Compatible with four-door, non-amplified 2018 - Up Jeep Wrangler and non-amplified 2020 - Up Jeep Gladiator Also compatible with two-door, non-scissor front seats in 2019 - Up Jeep Wrangler Includes Alpine's SPV-65X-WRA, SPV-65-JLT, PWE-S8, and KTP-445U 180W, 4-channel Power Pack amplifier 120W, 8" powered subwoofer (2x) 6.5" weather-resistant mid-bass drivers (2x) 1" weather-resistant teteron dome tweeters with vehicle-specific connectors and crossovers Vehicle-specific front speaker pods with vehicle-specific connectors Tweeter adapter plates allow for the use of the original factory tweeter locations SPV-65-JLT weather-resistant rear soundbar speaker system Rugged, premium grills designed to emulate the factory look and appeal Vehicle-specific connectors for plug-and-play speaker installation  Utilizes factory bolt locations Durable stamped, steel frame speaker basket design Includes template for mounting Vehicle-specific T-harness for installation with OEM radio into compatible 2018 - Up Jeep Wrangler and 2020 - Up Jeep Gladiator vehicles Vehicle-specific mounting brackets allow the powered sub and amp to be secured Front (SPV-65X-WRA): Power handling: 75 watts RMS (225 watts peak) Frequency response: 65kHz – 22kHz Nominal impedance: 4 ohms Weather-resistant: IP55 Rear (SPV-65-JLT): Power handling: 90 watts RMS (270 watts peak) Frequency response: 50kHz – 22kHz Nominal impedance: 4 ohms Weather-resistant: IP55 Powered Subwoofer (PWE-S8): 120 watts RMS (240 watts peak) Frequency response: 32 - 150Hz Variable low-pass crossover (80-200 Hz) Variable phase control (0-180 degrees) preamp- and speaker-level inputs Four Channel Power Pack Amplifier (KTP-445U): 45 watts RMS x 4 at 4 or 2 ohms 90 watts RMS x 2 bridged at 4 ohms Selectable high-pass filters (60, 80, or 120 Hz at 12 dB/octave) Switchable RCA or speaker-level inputs Dimensions: 27” L x 18.5” W x 19.5” H Weight: 40lbs Authorized Dealer 1-year Manufacturer's Warranty Note: Not compatible with the factory-equipped subwoofer system What's in the PSS-24WRA package: PSS-24WRA owner's manual This Alpine kit contains five individually packaged items: PWE-S8 Subwoofer KTP-445U Amplifier SPV-65X-WRA 6.5" Component Speakers SPV-65-JLT 6.5" 2-Way Speakers ALP-POD-JLTR Speaker Pods PSU-BKT-JL-R PWE Right Bracket JL PSU-BKT-JL-L PWE Left Bracket JL ALP-HRN-PSU300 PSU Power Harness ALP-THRN-CH2 Chrysler T-Harness CT6 6" Cable Ties PHPSM412 Pan Head Phillips Screw M4x12 SLWM4 M4 Split Lock Washers PHSCR832 8-32 Pan Head Phillips screws PSS-WRA-IM Installation Manual ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine PSS-23WRA Powered Sound System Upgrade for 2018 - Up Jeep Wrangler Unlimited Powered System Upgrade for 2018-Up Jeep® Wrangler Unlimited JL TAKE YOUR WRANGLER’S SOUND BEYOND THE FACTORYEnjoy premium sound quality even with your JL’s top-off! The PSS-23WRA is a 300-watt system upgrade featuring a powered subwoofer, amplifier, and tweeters for the 2018-Up Jeep Wrangler Unlimited JL without the factory amplified system. The PSS-23WRA provides excellent sound performance whether the JL’s top is on or off.SOUND THAT WILL TURN HEADS WITH THE TOP ON OR OFFThe PWE-S8 subwoofer is engineered to load and disperse lower-frequency sound into the passenger’s footwell area to maximize bass extension throughout the Jeep for great sound with the top on or off. The subwoofer includes a remote bass knob so you can control the bass level from the convenience of your dashboard. The Included 4-channel amplifier more than doubles the power over the factory system allowing you to enjoy your tunes with the top off. EASY BOLT-IN INSTALLATIONThe PWE-S8 Powered Subwoofer and KTP-445U Power Pack Amplifier don’t take up much since they mount under the passenger’s seat. The two products come pre-connected for easy bolt-in installation with simple wire routing. Mounting brackets for the products are included as well.SIMPLE TWEETER REPLACEMENTThe SPR-10TW Component Tweeters replace the factory tweeters on the top of the dash. These high-performance tweeters add much-needed high-frequency response that is lacking in the factory Jeep JL systems. An EQ Ring improves the tweeter’s dispersion characteristics and delivers a wide, flat frequency response.WORKS WITH ANY RADIOThe included T-harness gets the necessary audio signal connections from behind the Wrangler’s radio, making installation a breeze. The PSS-23WRA is compatible with Alpine universal head units, the factory Jeep base radio, or other aftermarket radios. General Features: Complete Direct Fit Audio System Upgrade Compatible with 2018 - Up Jeep Wrangler Unlimited JL Compatible with models that don't have a factory-amplified system All installation hardware, such as speaker adapters and amplifier wiring, included CEA-2006 Compliant System 300 Watt RMS sound system The system consists of: 8" Powered Subwoofer Universal Power Pack Amplifier 2" Component Tweeters Tweeter Adapters Authorized Dealer 1-year Manufacturer's Warranty PWE-S8 Subwoofer Features: Peak: 240 watts RMS: 120 watts 8" woofer high-excursion cone built-in Class D amplifier frequency response: 32-150 Hz variable low-pass crossover (80-200 Hz) variable phase control (0-180 degrees) preamp- and speaker-level inputs Dimensions: 13-1/2"W x 3"D x 9"H KTP-445U Amplifier Features: RMS Power Rating: 4 ohms: 45 watts x 4 Channel 2 ohms: 45 watts x 4 Channel 4 ohms: 90 watts x 2 Channel (Bridged) Total RMS power output: 180 watts CEA-2006 compliant amplifier Increases the output of any head unit without having to install a full-size amplifier and amp install kit The Independent front/Rear gain switch is adjustable from high to low Runs off the receiver's power circuit High-Pass Filter: selectable 60/80/120 Hz @ 12 dB/octave Fast and simple installation 4-channel operation for four speakers Minimum impedance of 2 ohms Frequency response: 20-20,000 Hz Fuse Rating: 15A x 1 SPR-10TW Component Tweeters: 2" Type-R Series Car Tweeters Power Handling: Peak: 450 watts per pair / 225 watts each RMS: 150 watts per pair / 75 watts each Silk Dome tweeter construction 4 ohms impedance Copper-Clad Aluminum high-temperature voice coil 75% smaller external crossover filter removes harmful frequencies 4-way tweeter level attenuation High-grade Neodymium magnet structure Surface / Bottom / Flush Mountable CEA-2031 compliant speakers Sensitivity: 88dB Frequency response: 1,000-29,000 Hz Top-mount depth: 11/16" Vehicle Compatibility: JEEP 2018 - Up Wrangler Unlimited JL Compatible with Wrangler JL Models that don't have a factory amplified system What's in the PSS-23WRA package: KTP-445U amplifier PWE-S8 powered subwoofer (both pre-attached to vehicle mounting bracket) 7' Signal harness 12' Loomed power wire w/ inline 20A fuse 52-Pin t-harness Four 10" speaker to RCA harnesses Two SPR-10TW tweeters w/ integrated mounting plates and 8" wire loom w/ inline crossovers Remote bass-level control w/ attached 16' cable 3" Strip of hook-and-loop fastener Ten 6" wire-ties 1/2" Self-tapping screw Star-washer 2 Alpine logos Installation guide Warranty sheet Alpine PSS-23WRA owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine PWE-S8-WRA 8" Amplified Custom Fit for 2011-up Jeep Wrangler (4 doors) - Under Seat Plug and Play 120 Watt Amplified Subwoofer DISCREET, WITH A PUNCH The small but powerful PWE-S8-WRA consists of an 8-inch powered subwoofer with a built-in 120 watts amp, a bracket designed to bolt the subwoofer under the Wrangler driver’s seat, a remote bass knob and Wrangler-specific wiring harnesses for plug-and-play connection to your aftermarket or factory in-dash system. The powered subwoofer measures just 13.5” L x 9” W x 3” D, so you can add low, punchy, accurate bass to your Jeep without taking up usable storage space. SOUND CONTROL AT YOUR FINGERTIPS Subwoofer controls like Phase, Gain, LP Crossover, and Remote Sub Level are found on the side panel, or mount the remote bass knob on your dash and use it to make bass level adjustments easily.General Features: 8-inch Compact Powered Subwoofer System Compatible with 2011-Up Jeep Wrangler 4-door vehicles Plug-and-play installation Installs under the driver's seat Works with an Alpine or aftermarket head unit or with the factory Jeep radio Built-in 120 Watt Amplifier Strong and Durable cast aluminum enclosure Dimensions: 13.5"L x 3"D x 9"W Authorized Dealer 1-year Manufacturer's Warranty Note: Not compatible with the factory-equipped subwoofer system What's in the box: Amplified enclosure with one 8" subwoofer installed 80" Wiring harness (Power/ Ground/ Speaker level input) Wrangler radio T-Harness (with in-line fuse holder) Two 15 amp ATO fuses (one installed in the power wire fuse holder/ 1 spare) Remote level control with 15' cable attached (3.5mm mini-plug on end) Adhesive-backed hook and loop mounting fasteners (to mount the remote) 2 Wrangler mounting brackets Eight M4x10mm Machine screws (each with a flat washer and split lock washer) Four M6x10mm Machine screws Fifteen 7" Zip ties Installation instructions Owner's manual (English/ French/ Spanish) Warranty information Online product registration information System installation notice Alpine PWE-S8-WRA owner's manual ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Cerwin Vega VPAS10 10" Powered Active Under Seat Subwoofer Enclosure the legendary brand in the mobile audio industry, announces the introduction of its very first powered active subwoofer. The VPAS10 (Vega Powered Active Subwoofer) consists of an active 10" subwoofer amplified for extreme output. Encased in a solid cast aluminum body frame for superior heat dissipation, the VPAS10 is compact enough for installation in the tightest of spaces without sacrificing performance. General Features: 10" Low Profile Amplified Subwoofer Power Handling: Peak: 550 watts RMS: 200 watts PWM MOSFET Power Supply/Thermal Protection Circuit Remote Subwoofer Control Included RCA and High-Level Inputs Delayed Soft Remote Turn On Adjustable Input Sensitivity Variable Bass Boost: 0 - +12 dB Variable Low-pass Filter: 85 - 150 Hz Constant Subsonic Filter: @ 35Hz Selectable Phase : 0 or 180 degrees Fuse Rating: 25A x 1 Dimensions: 13.60" L x 9.60" W x 2.60" H (approx) ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Cerwin Vega VPAS10 10" Powered Active Under Seat Subwoofer Enclosure the legendary mobile audio industry brand announces the introduction of its first powered active subwoofer. The VPAS10 (Vega Powered Active Subwoofer) consists of an active 10" subwoofer amplified for extreme output. Encased in a solid cast aluminum body frame for superior heat dissipation, the VPAS10 is compact enough to install in the tightest spaces without sacrificing performance. General Features: 10" Low Profile Amplified Subwoofer Power Handling: Peak: 550 watts RMS: 200 watts PWM MOSFET Power Supply/Thermal Protection Circuit Remote Subwoofer Control Included RCA and High-Level Inputs Delayed Soft Remote Turn On Adjustable Input Sensitivity Variable Bass Boost: 0 - +12 dB Variable Low-pass Filter: 85 - 150 Hz Constant Subsonic Filter: @ 35Hz Selectable Phase : 0 or 180 degrees Fuse Rating: 25A x 1 Dimensions: 13.60" L x 9.60" W x 2.60" H (approx) ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine PSS-23WRA Powered Sound System Upgrade for 2018 - Up Jeep Wrangler Unlimited Powered System Upgrade for 2018-Up Jeep® Wrangler Unlimited JL TAKE YOUR WRANGLER’S SOUND BEYOND THE FACTORYEnjoy premium sound quality even with your JL’s top-off! The PSS-23WRA is a 300-watt powered system upgrade featuring a powered subwoofer, amplifier, and tweeters for the 2018-Up Jeep Wrangler Unlimited JL without the factory amplified system. The PSS-23WRA provides excellent sound performance whether the JL’s top is on or off.SOUND THAT WILL TURN HEADS WITH THE TOP ON OR OFFThe PWE-S8 subwoofer is engineered to load and disperse lower-frequency sound into the passenger’s footwell area to maximize bass extension throughout the Jeep for great sound with the top on or off. Included with the subwoofer is a remote bass knob so you can control the bass level from the convenience of your dashboard. The Included 4-channel amplifier more than doubles the power over the factory system allowing you to enjoy your tunes with the top off. EASY BOLT-IN INSTALLATIONThe PWE-S8 Powered Subwoofer and KTP-445U Power Pack Amplifier don’t take up much since they mount under the passenger’s seat. The two products come pre-connected for easy bolt-in installation with simple wire routing. Mounting brackets for the products are included as well.SIMPLE TWEETER REPLACEMENTThe SPR-10TW Component Tweeters replace the factory tweeters on the top of the dash. These high-performance tweeters add much-needed high-frequency response that is lacking in the factory Jeep JL systems. An EQ Ring improves the tweeter’s dispersion characteristics and delivers a wide, flat frequency response.WORKS WITH ANY RADIOThe included T-harness gets the necessary audio signal connections from behind the Wrangler’s radio, making installation a breeze. The PSS-23WRA is compatible with Alpine universal head units, the factory Jeep base radio, or other aftermarket radios. General Features: Complete Direct Fit Audio System Upgrade Compatible with 2018 - Up Jeep Wrangler Unlimited JL Compatible with models that don't have a factory-amplified system All installation hardware, such as speaker adapters and amplifier wiring, included CEA-2006 Compliant System 300 Watt RMS sound system The system consists of: 8" Powered Subwoofer Universal Power Pack Amplifier 2" Component Tweeters Tweeter Adapters Authorized Dealer 1-year Manufacturer's Warranty PWE-S8 Subwoofer Features: Peak: 240 watts RMS: 120 watts 8" woofer high-excursion cone built-in Class D amplifier frequency response: 32-150 Hz variable low-pass crossover (80-200 Hz) variable phase control (0-180 degrees) preamp- and speaker-level inputs Dimensions: 13-1/2"W x 3"D x 9"H KTP-445U Amplifier Features: RMS Power Rating: 4 ohms: 45 watts x 4 Channel 2 ohms: 45 watts x 4 Channel 4 ohms: 90 watts x 2 Channel (Bridged) Total RMS power output: 180 watts CEA-2006 compliant amplifier Increases the output of any head unit without having to install a full-size amplifier and amp install kit The Independent front/Rear gain switch is adjustable from high to low Runs off the receiver's power circuit High-Pass Filter: selectable 60/80/120 Hz @ 12 dB/octave Fast and simple installation 4-channel operation for four speakers Minimum impedance of 2 ohms Frequency response: 20-20,000 Hz Fuse Rating: 15A x 1 SPR-10TW Component Tweeters: 2" Type-R Series Car Tweeters Power Handling: Peak: 450 watts per pair / 225 watts each RMS: 150 watts per pair / 75 watts each Silk Dome tweeter construction 4 ohms impedance Copper-Clad Aluminum high-temperature voice coil 75% smaller external crossover filter removes harmful frequencies 4-way tweeter level attenuation High-grade Neodymium magnet structure Surface / Bottom / Flush Mountable CEA-2031 compliant speakers Sensitivity: 88dB Frequency response: 1,000-29,000 Hz Top-mount depth: 11/16" Vehicle Compatibility: JEEP 2018 - Up Wrangler Unlimited JL Compatible with Wrangler JL Models that don't have a factory amplified system What's in the box: KTP-445U amplifier PWE-S8 powered subwoofer (both pre-attached to vehicle mounting bracket) 7' Signal harness 12' Loomed power wire w/ inline 20A fuse 52-Pin t-harness Four 10" speaker to RCA harnesses Two SPR-10TW tweeters w/ integrated mounting plates and 8" wire loom w/ inline crossovers Remote bass-level control w/ attached 16' cable 3" Strip of hook-and-loop fastener Ten 6" wire-ties 1/2" Self-tapping screw Star-washer 2 Alpine logos Installation guide Warranty sheet Alpine PSS-23WRA owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine PWE-S8-WRA 8" Amplified Custom Fit for 2011-up Jeep Wrangler (4 doors) - Under Seat Plug and Play 120 Watt Amplified Subwoofer DISCREET, WITH A PUNCH The small but powerful PWE-S8-WRA consists of an 8-inch powered subwoofer with a built-in 120 watts amp, a bracket designed to bolt the subwoofer under the Wrangler driver’s seat, a remote bass knob and Wrangler-specific wiring harnesses for plug-and-play connection to your aftermarket or factory in-dash system. The powered subwoofer measures just 13.5” L x 9” W x 3” D, so you can add low, punchy, accurate bass to your Jeep without taking up usable storage space. SOUND CONTROL AT YOUR FINGERTIPS Subwoofer controls like Phase, Gain, LP Crossover, and Remote Sub Level are found on the side panel, or mount the remote bass knob on your dash and use it to make bass level adjustments easily.General Features: 8-inch Compact Powered Subwoofer System Compatible with 2011-Up Jeep Wrangler 4-door vehicles Plug-and-play installation Installs under the driver's seat Works with an Alpine or aftermarket head unit or with the factory Jeep radio Built-in 120 Watt Amplifier Strong and Durable cast aluminum enclosure Dimensions: 13.5"L x 3"D x 9"W Authorized Dealer 1-year Manufacturer's Warranty Note: Not compatible with the factory-equipped subwoofer system What's in the box: Amplified enclosure with one 8" subwoofer installed 80" Wiring harness (Power/ Ground/ Speaker level input) Wrangler radio T-Harness (with in-line fuse holder) Two 15 amp ATO fuses (one installed in the power wire fuse holder/ 1 spare) Remote level control with 15' cable attached (3.5mm mini-plug on end) Adhesive-backed hook and loop mounting fasteners (to mount the remote) 2 Wrangler mounting brackets Eight M4x10mm Machine screws (each with a flat washer and split lock washer) Four M6x10mm Machine screws Fifteen 7" Zip ties Installation instructions Owner's manual (English/ French/ Spanish) Warranty information Online product registration information System installation notice Alpine PWE-S8-WRA owner's manual ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine PWE-S8 120W Compact Powered 8" Car Subwoofer for Under or Behind the Seat Its super shallow structure makes it ideal for under-seat installation or in small spaces. The compact, 120W PWE-S8 amplified subwoofer system lets you add deep, accurate bass to your sound system without taking up much space in your vehicle. General Features: 120W Compact Powered 8" Car Subwoofer Peak Power Handling: 240 watts RMS Power Handling: 120 watts 8" woofer high-excursion cone built-in Class D amplifier frequency response: 32-150 Hz variable low-pass crossover (80-200 Hz) variable phase control (0-180 degrees) preamp- and speaker-level inputs Dimensions: 13-1/2"W x 3"D x 9"H Authorized Dealer 1-year Manufacturer's Warranty What's in the PWE-S8 package: PWE-S8 owner's manual Amplified enclosure with one 8" subwoofer installed 12" Wiring harness Two 15 amp ATO fuses Remote level control with 15' cable attached Adhesive-backed hook and loop mounting fasteners 4 Mounting brackets Eight 5/8" Pan head self-tapping screws Eight M4x7.5mm Machine screws Warranty information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine PWE-S8-WRA 8" Amplified Custom Fit for 2011-up Jeep Wrangler (4 doors) - Under Seat Plug and Play 120 Watt Amplified Subwoofer DISCREET, WITH A PUNCH The small but powerful PWE-S8-WRA consists of an 8-inch powered subwoofer with a built-in 120 watts amp, a bracket designed to bolt the subwoofer under the Wrangler driver’s seat, a remote bass knob and Wrangler-specific wiring harnesses for plug-and-play connection to your aftermarket or factory in-dash system. The powered subwoofer measures just 13.5” L x 9” W x 3” D, so you can add low, punchy, accurate bass to your Jeep without taking up usable storage space. SOUND CONTROL AT YOUR FINGERTIPS Subwoofer controls like Phase, Gain, LP Crossover, and Remote Sub Level are found on the side panel, or mount the remote bass knob on your dash and use it to make bass level adjustments easily.General Features: 8-inch Compact Powered Subwoofer System Compatible with 2011-Up Jeep Wrangler 4-door vehicles Plug-and-play installation Installs under the driver's seat Works with an Alpine or aftermarket head unit or with the factory Jeep radio Built-in 120 Watt Amplifier Strong and Durable cast aluminum enclosure Dimensions: 13.5"L x 3"D x 9"W Authorized Dealer 1-year Manufacturer's Warranty Note: Not compatible with the factory-equipped subwoofer system What's in the box: Amplified enclosure with one 8" subwoofer installed 80" Wiring harness (Power/ Ground/ Speaker level input) Wrangler radio T-Harness (with in-line fuse holder) Two 15 amp ATO fuses (one installed in the power wire fuse holder/ 1 spare) Remote level control with 15' cable attached (3.5mm mini-plug on end) Adhesive-backed hook and loop mounting fasteners (to mount the remote) 2 Wrangler mounting brackets Eight M4x10mm Machine screws (each with a flat washer and split lock washer) Four M6x10mm Machine screws Fifteen 7" Zip ties Installation instructions Owner's manual (English/ French/ Spanish) Warranty information Online product registration information System installation notice Alpine PWE-S8-WRA owner's manual ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.