Hot Deals (11104)

2 Alpine R2-W12D2 2250W Max (750W RMS) 12" R-Series Dual 2-Ohm Car Subwoofer The new 2022 R-Series subwoofers are here - drawing from decades of Subwoofer engineering experience. They deliver deep, clean, accurate bass and feature Alpine’s HAMR Surround for maximum cone excursion, delivering tons of bass output. The new ceramic dust cap is lightweight and rigid, keeping distortion at an absolute minimum. The enlarged motor structure ensures better woofer control for a strong, clean bass response. General Features: 12" Dual 2 ohm Type-R Subwoofer Peak Power Handling: 2250watts RMS Power Handling: 750 watts Recommended power range: 300 - 750W RMS CTA-2031 compliant power ratings Parabolic pulp/kevlar cone H.A.M.R. surround Polypropylene, mica, and talc dust cap Reinforced cone neck and spider joint Cast aluminum frame with integral shorting sleeve 8AWG push terminals with VC configuration jumpers 2.6" High excursion overhung voice coil 127 oz. Strontium ferrite segmented magnet Top-mount depth: 6-3/8" Cutout diameter: 10-7/8" Frequency Response: 24 - 200Hz Sensitivity: 84.3dB Resonance Frequency (Fs): 27Hz Authorized Dealer 1-year Manufacturer's Warranty What's in the R2-W12D2 package: R2-W12D2 owner's manual One 12" Dual 2-ohm voice coil subwoofer Two 3" jumper cables R-Series Subwoofer Application Guide Online product registration information Warranty Information https://www.youtube.com/watch?v=ihjWBSOYVxE&t=179s Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine PWE-S8-WRA 8" Amplified Custom Fit for 2011-up Jeep Wrangler (4 doors) - Under Seat Plug and Play 120 Watt Amplified Subwoofer DISCREET, WITH A PUNCH The small but powerful PWE-S8-WRA consists of an 8-inch powered subwoofer with a built-in 120 watts amp, a bracket designed to bolt the subwoofer under the Wrangler driver’s seat, a remote bass knob and Wrangler-specific wiring harnesses for plug-and-play connection to your aftermarket or factory in-dash system. The powered subwoofer measures just 13.5” L x 9” W x 3” D, so you can add low, punchy, accurate bass to your Jeep without taking up usable storage space. SOUND CONTROL AT YOUR FINGERTIPS Subwoofer controls like Phase, Gain, LP Crossover, and Remote Sub Level are found on the side panel, or mount the remote bass knob on your dash and use it to make bass level adjustments easily.General Features: 8-inch Compact Powered Subwoofer System Compatible with 2011-Up Jeep Wrangler 4-door vehicles Plug-and-play installation Installs under the driver's seat Works with an Alpine or aftermarket head unit or with the factory Jeep radio Built-in 120 Watt Amplifier Strong and Durable cast aluminum enclosure Dimensions: 13.5"L x 3"D x 9"W Authorized Dealer 1-year Manufacturer's Warranty Note: Not compatible with the factory-equipped subwoofer system What's in the box: Amplified enclosure with one 8" subwoofer installed 80" Wiring harness (Power/ Ground/ Speaker level input) Wrangler radio T-Harness (with in-line fuse holder) Two 15 amp ATO fuses (one installed in the power wire fuse holder/ 1 spare) Remote level control with 15' cable attached (3.5mm mini-plug on end) Adhesive-backed hook and loop mounting fasteners (to mount the remote) 2 Wrangler mounting brackets Eight M4x10mm Machine screws (each with a flat washer and split lock washer) Four M6x10mm Machine screws Fifteen 7" Zip ties Installation instructions Owner's manual (English/ French/ Spanish) Warranty information Online product registration information System installation notice Alpine PWE-S8-WRA owner's manual ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine KCX-C2600B Universal Front and Rear Camera Selector Easily control your single view camera or Alpine direct multi-view cameras with the KCX-C2600B Front and Rear Camera Switcher. Use the two-button controller to choose the desired camera and toggle through the various viewing modes from the camera (when connected to a multi-view camera). The controller can be mounted on your dashboard for easy access. The KCX-C2600B features two direct inputs for the front and rear cameras, and one RCA input for a non-Alpine rear camera. It also has one universal RCA output for other display devices such as a factory screen (third-party factory camera interface required). General Features: Control module for multiple camera systems Recommended cameras include the Alpine HCE-C2100RD Front and rear view cameras connect into one module Connect two multi-view cameras to screens with the RCA input Included switch allows selection of viewing modes Supports power supply for direct cameras Also found as: Dimensions: 3.9"W x 1.9"D x .9"H Authorized Internet Dealer 1-year Warranty Output Image: Normal image, NTSC Video signal 16:9 Image output for wide-screen Image Output impedance: 75 Ohm (1Vp-p) Power Requirement: 12 V.DC Negative Ground Power Consumption: Less than 1.7W (12V) Operating Temperature: -30°C - +80°C What's in the box: Alpine KCX-C2600B owner's manual Dual multi-camera selector interface module (attached 6.5' power/ground/reverse-in wires and 19.5' reverse out wire) Controller (attached 9.75' cable) 6.5' Composite video cable 3 Self-adhesive clips 2 Hook-and-loop strips Two-sided tape ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Absolute CAM1500S For Pioneer AVIC-5200NEX Bullet Camera Hi-Quality IR Night Vision / Back-Up Camera HI Quality Night Vision Car License Plate Camera With Built-IN I.R. Camera General Features: Solid Silver Aluminum Frame Protects Form Incidental Damage Water -Cold Weather & Vibration Proof Ip68 Powerful 1/4 CMOS RGB Color/ Image Sensor Effective Pixels 628* 586 Sensor Size 5.961* 4.276mm Min Resolution 420 Tv Lines Lens 1.8 Mm 170 Degrees Electronic Shutter Speed 1/50-1/100,000 Per Second Low Current Consumption 300ma Max Min Operating Temperature 30 Degrees C Cold Temperature Anti Fog Function 8 Powerful Infrared LEDs Real-Time Viewing Up To 300 Meters 170 Degree Adjustable Wide-Angle Lens for Optimal Blindspot Elimination Min Illumination 0 Lux On-Screen Distance Guide Display for Assisted Parking Easy-to-Follow Installation Instructions Comes with 17’ Video Cable Mounting Hardware Video Cable Available for SUV & RV Applications 1 Year Warranty Included THIS IS A BRAND-NEW MODEL NIGHT VISION CAMERA AND WILL WORK WITH PIONEER AVIC-5200NEX, THIS ITEM IS NOT MANUFACTURED BY PIONEER, ITEM RECEIVED MAY DIFFER SLIGHTLY FROM THE PICTURES SHOWN. Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine HCE-C1100 Universal backup camera surface-mountAlpine's HCE-C1100 backup camera is an excellent add-on when buying a new touchscreen car stereo. With low light capability and a wide viewing angle, you'll have a perfect picture of what's behind your vehicle, day or night.This tiny camera measures less than one square inch, so it'll fit just about anywhere. The package includes a 21-foot cable with composite video RCA plugs that allows the camera to connect to any in-dash receiver or front-mount screen with a composite video input.Frame itGeneral Features: backup camera with standard composite (RCA) video cable mounting hardware and 21-foot power/video cable included compatible with any radio with an RCA video input (most aftermarket models, only a few factories) 1/4" CMOS image sensor color video output illumination range: 1.5 to 100,000 lux weather-proof camera housing warranty: 1 year MFR # HCE-C1100 What's in the HCE-C1100 package: HCE-C1100 owner's manual Rearview camera (attached 5' power/ground cable) 23' Composite video cable Mounting bracket Hex-key Rubber sleeve 4 Large screws 2 Small screws Owner's Manual Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine KTX-C10LP License Plate Mounting Kit This product is solely the mounting kit. This package does not include the backup camera, which is required and sold separately. General Features: Alpine KTX-C10LP License Plate Mounting Kit Works with select Alpine rear-view cameras Easy to install Constructed from a rigid, sturdy cast metal frame Built-in LED’s illuminate your plate for added safety Connect to any in-dash monitor or AV head unit with auxiliary input Convenient camera view provides protection when backing up Compatible with Alpine HCE-C105 and Alpine HCE-C107D Authorized Dealer 1-year Manufacturer's Warranty What's in the box: License plate frame mount Camera mounting bracket 4 Self-tapping screws 4 Hex-head screws 4 Large machine screws with flat and lock washers installed 4 Small machine screws Hex key Installation Manual Alpine KTX-C10LP owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine PSS-23WRA Powered Sound System Upgrade for 2018 - Up Jeep Wrangler Unlimited Powered System Upgrade for 2018-Up Jeep® Wrangler Unlimited JL TAKE YOUR WRANGLER’S SOUND BEYOND THE FACTORYEnjoy premium sound quality even with your JL’s top-off! The PSS-23WRA is a 300-watt powered system upgrade featuring a powered subwoofer, amplifier, and tweeters for the 2018-Up Jeep Wrangler Unlimited JL without the factory amplified system. The PSS-23WRA provides excellent sound performance whether the JL’s top is on or off.SOUND THAT WILL TURN HEADS WITH THE TOP ON OR OFFThe PWE-S8 subwoofer is engineered to load and disperse lower-frequency sound into the passenger’s footwell area to maximize bass extension throughout the Jeep for great sound with the top on or off. Included with the subwoofer is a remote bass knob so you can control the bass level from the convenience of your dashboard. The Included 4-channel amplifier more than doubles the power over the factory system allowing you to enjoy your tunes with the top off. EASY BOLT-IN INSTALLATIONThe PWE-S8 Powered Subwoofer and KTP-445U Power Pack Amplifier don’t take up much since they mount under the passenger’s seat. The two products come pre-connected for easy bolt-in installation with simple wire routing. Mounting brackets for the products are included as well.SIMPLE TWEETER REPLACEMENTThe SPR-10TW Component Tweeters replace the factory tweeters on the top of the dash. These high-performance tweeters add much-needed high-frequency response that is lacking in the factory Jeep JL systems. An EQ Ring improves the tweeter’s dispersion characteristics and delivers a wide, flat frequency response.WORKS WITH ANY RADIOThe included T-harness gets the necessary audio signal connections from behind the Wrangler’s radio, making installation a breeze. The PSS-23WRA is compatible with Alpine universal head units, the factory Jeep base radio, or other aftermarket radios. General Features: Complete Direct Fit Audio System Upgrade Compatible with 2018 - Up Jeep Wrangler Unlimited JL Compatible with models that don't have a factory-amplified system All installation hardware, such as speaker adapters and amplifier wiring, included CEA-2006 Compliant System 300 Watt RMS sound system The system consists of: 8" Powered Subwoofer Universal Power Pack Amplifier 2" Component Tweeters Tweeter Adapters Authorized Dealer 1-year Manufacturer's Warranty PWE-S8 Subwoofer Features: Peak: 240 watts RMS: 120 watts 8" woofer high-excursion cone built-in Class D amplifier frequency response: 32-150 Hz variable low-pass crossover (80-200 Hz) variable phase control (0-180 degrees) preamp- and speaker-level inputs Dimensions: 13-1/2"W x 3"D x 9"H KTP-445U Amplifier Features: RMS Power Rating: 4 ohms: 45 watts x 4 Channel 2 ohms: 45 watts x 4 Channel 4 ohms: 90 watts x 2 Channel (Bridged) Total RMS power output: 180 watts CEA-2006 compliant amplifier Increases the output of any head unit without having to install a full-size amplifier and amp install kit The Independent front/Rear gain switch is adjustable from high to low Runs off the receiver's power circuit High-Pass Filter: selectable 60/80/120 Hz @ 12 dB/octave Fast and simple installation 4-channel operation for four speakers Minimum impedance of 2 ohms Frequency response: 20-20,000 Hz Fuse Rating: 15A x 1 SPR-10TW Component Tweeters: 2" Type-R Series Car Tweeters Power Handling: Peak: 450 watts per pair / 225 watts each RMS: 150 watts per pair / 75 watts each Silk Dome tweeter construction 4 ohms impedance Copper-Clad Aluminum high-temperature voice coil 75% smaller external crossover filter removes harmful frequencies 4-way tweeter level attenuation High-grade Neodymium magnet structure Surface / Bottom / Flush Mountable CEA-2031 compliant speakers Sensitivity: 88dB Frequency response: 1,000-29,000 Hz Top-mount depth: 11/16" Vehicle Compatibility: JEEP 2018 - Up Wrangler Unlimited JL Compatible with Wrangler JL Models that don't have a factory amplified system What's in the box: KTP-445U amplifier PWE-S8 powered subwoofer (both pre-attached to vehicle mounting bracket) 7' Signal harness 12' Loomed power wire w/ inline 20A fuse 52-Pin t-harness Four 10" speaker to RCA harnesses Two SPR-10TW tweeters w/ integrated mounting plates and 8" wire loom w/ inline crossovers Remote bass-level control w/ attached 16' cable 3" Strip of hook-and-loop fastener Ten 6" wire-ties 1/2" Self-tapping screw Star-washer 2 Alpine logos Installation guide Warranty sheet Alpine PSS-23WRA owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Absolute SAG12 Single 12" Subwoofer Sealed Angled Truck or Hatchback Enclosure Empty Box Absolute USA hatchback-style Truck Box Bass enclosures are built to last and ready to help your sub deliver real low-frequency firepower. These unloaded boxes feature high-grade, medium-density fiberboard construction with sealed inner braces that help combat resonance by reducing vibrations. Adding bass to a regular cab truck can be a real headache! Luckily, we have the perfect solution to this problem. This sealed enclosure is designed for sound clarity, and the box has enough mounting depth for entry and flat-piston style subwoofer(s). This angled 12" box is perfect for single cab trucks and hatchback vehicles looking to save some space. We are designed to fit behind the seat of most trucks. Constructed with high-quality MDF, the box is fully carpeted and made of 5/8" MDF wood (medium-density fiberboard), not particle board. Fits Most 12" Shallow-Mount Subwoofers. We recommend purchasing subwoofer grille(s) for this model enclosure to protect your sub(s) from rubbing into the seat. General Features: Heavy Duty Sealed Back-Angle Single 12-Inch Subwoofer Enclosure Subwoofer Box 12-Inch Sealed High Quality 5/8" MDF Construction Gold Binding Post loaded terminal cups 12" Single Universal Truck Style Sealed Subwoofer Enclosure Premium carpeted finish Glued and braced with fasteners 12" Angled Truck Box for Car Subwoofers Great for installing subwoofers in locations that do not have a lot of space Perfect for trucks or cars with small trunks Carpeted in durable black carpet Spring clip terminals for easy connection Pre-lined with a layer of polyfill Made from 5/8" MDF Subwoofer mounting depth: 4.5" Subwoofer cutout diameter: 11-1/16" Box volume: 0.80 cubic feet Dimensions: 5-1/4"TD x 8-1/2"BD x 20"W x 15-3/8"H What's in the SAG12 package: Single hatchback-style enclosure for 12" subwoofer with spring-post terminals Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Absolute 6.5PKG 6.5" Single Square Subwoofer Enclosure Speaker Box - BlackGeneral Features: Sealed airtight chamber each holds (1) 6.5 Inches speaker One Pair of 6.5" Angled Single Sealed Speaker Enclosures Speaker mounting depth: 4" Durable 1/2" Medium Density Fiberboard (MDF) construction Black carpet finish One set of spring terminals Each box stuffed with polyfill Box volume (net. int.): 0.20 cubic feet (per box) Solid MDF construction, Durable carpet, and Speaker terminal cup Black Color Cutout: 5" Total Air Volume: 0.09 Cubic Ft. Weight: 3 Lbs. Mounting Depth: 4 1/4" Dimensions: Height: 8 1/8” Length: 8 1/8" Depth: 5" Construction: 1/2"High-Density MDF Wood Carpeted With Durable Trunk Liner Finish 1 Spring-Loaded Terminal ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Absolute SKS12V Single 12-Inch Kicker Solo-Baric Square Slot-Ported Sub Box Built for a Kicker 12-Inch Square S12L3/S12L5/S12L7 Subwoofer Solid MDF Construction Durable Carpet Gold-Plated Binding Post Terminals Slot -Port Tuned 38Hz General Feature: 12" Square Hole, Rear Ported Subwoofer Enclosure for Kicker Solo-Baric L3/L7 Subwoofers ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Absolute PDEB10PI (Pink/black) Dual 10", 3/4" MDF Twin Port Subwoofer Enclosure with Pink High Gloss Face Board General Features: Dual 10" Ported Subwoofer Enclosure Made from durable 3/4" Medium Density Fiberboard (MDF) Pink high gloss front face board Covered in durable black carpet Two binding post terminals on the back of the enclosure Each terminal is banana-clip ready Square box enclosure universal for most vehicles Front Panel is Red Also available in Black, Blue, Pink, Yellow, and Silver Subwoofer mounting depth: 10" Subwoofer cutout diameter: 9-1/8" Total Box volume: 2.0 cubic feet Box volume: 1.0 cubic feet (per chamber) Dimensions: 14"D x 30-1/2"W x 14"H Authorized Internet Dealer Port Specifications: Dual rectangular slot ports Number of ports: 2 Port volume: 0.2 cubic feet (per port) Total port volume: 0.4 cubic feet Port dimensions: 19"D x 1-1/2"W x 12-1/4"H ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Absolute USA PSEB10P Single 10-Inch Ported Subwoofer Enclosure with Pink High Gloss Face Board Single 10" Ported Subwoofer Enclosure w/ Pink High Gloss Face Board General Features: Single 10" Ported Subwoofer Enclosure Made from durable 3/4" Medium Density Fiberboard (MDF) Black high gloss front face board Covered in durable black carpet Binding post terminals on the back of the enclosure Each terminal is banana-clip ready Square box enclosure universal for most vehicles Front Panel is Pink Also available in Yellow, Blue, Pink, Red, and Silver Subwoofer mounting depth: 10" Subwoofer cutout diameter: 9-1/8" Total Box volume: 1.0 cubic feet Dimensions: 14"D x 16-1/2"W x 14"H Authorized Internet Dealer ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov