Class-D Amplifiers (365)

Rockford Fosgate Prime R1200-1D 1200W RMS Prime Series Class-D Monoblock 1-Ohm Stable Amplifier The PRIME R1200-1D is an ultra-efficient mono amplifier for cars and trucks that can produce 1,200 Watts into a 1-Ohm load without taxing the electrical system. The frequency response of the R1200-1D is optimized exclusively for use with subwoofers. The Prime R1200-1D subwoofer amplifier delivers high efficiency through its Class-D circuitry while delivering rich, full bass to any system. This car amplifier is optimized for subwoofers, featuring an infrasonic filter to prevent ultra-low (inaudible) bass notes from damaging your subwoofer system. Match with a 4-channel stereo amplifier for your mids/highs and you'll have a Rockford Fosgate system that any Car Audio Fanatic will envy. General Features: Rockford Fosgate Prime Series R1200-1D Class-D 1-Ohm Stable Monoblock Amplifier RMS Power Rating: 4 ohms: 400 watts x 1 channel RMS Power Rating: 2 ohms: 800 watts x 1 channel RMS Power Rating: 1 ohm: 1200 watts x 1 channel CEA-2006 Compliant Amplifier Pulse Width Modulated MOSFET power supply Wired remote bass level control included LED power (green) and protect (red) indicators Soft start turn-on Nickel-plated RCA level inputs Nickel-plated screw terminals Preamp RCA outputs to daisy chain multiple amps 3-way protection circuitry (thermal, overload, and speaker short protection) Heavy-duty aluminum alloy heat-sink for extreme heat dissipation Input sensitivity: 150mV - 4V Frequency Response: 20 - 250Hz Total Harmonic Distortion (THD): <1.0% Signal to Noise Ratio: 100dB Variable low-pass filter: 50 - 250 Hz, 12 dB/octave Subsonic (infrasonic) filter: 15 - 40 Hz, 12 dB/octave Variable Bass Boost: 0 to +18 dB bass boost at 45 Hz Fuse Rating: 150A x 1 (recommended, not included) 12 AWG speaker wire gauge outputs 4-gauge power and ground wiring is recommended for installation Weight: 7.825 lbs Dimensions: 11.06"W x 6.77"L x 1.97"H Also Found As Prime 1200 Watt, R12001D, R1200, R12001 Authorized Internet Dealer 1-year Manufacturer's Warranty Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Precision Power TM1.6000D 6000W Peak Class D Trax Micro Series Monoblock Amplifier General Features: Trax Micro Series Class D Stable Monoblock Amplifier Total peak power output: 6000 watts LED Power/Protect Light Wired bass level remote control included Speaker-level (high-level) inputs Signal sensing remote turn-on Thermal, overload, and speaker short protection Compact and space saving design Fits behind truck, seats, or wheel wells Variable low-pass filter: 35 - 250 Hz Subsonic filter: 10 - 50 Hz Variable Bass Boost: 0 - 12 dB Fuse Rating: 50A 4 AWG gauge amplifier wiring kit is recommended for installation Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Precision Power TM1.4000D 4000W Peak Class D Trax Micro Series Monoblock Amplifier General Features: Trax Micro Series Class D Stable Monoblock Amplifier Total peak power output: 4000 watts LED Power/Protect Light Wired bass level remote control included Speaker-level (high-level) inputs Signal sensing remote turn-on Thermal, overload, and speaker short protection Compact and space saving design Fits behind truck, seats, or wheel wells Variable low-pass filter: 35 - 250 Hz Subsonic filter: 10 - 50 Hz Variable Bass Boost: 0 - 12 dB Fuse Rating: 50A 4 AWG gauge amplifier wiring kit is recommended for installation Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Precision Power TM1.3000D 3000W Peak (1500W RMS) Class D Trax Micro Series Monoblock Amplifier General Features: Trax Micro Series Class D 2 ohm Stable Monoblock Amplifier RMS Power Rating: 4 ohm: 1000 watts x 1 channel 2 ohm: 1500 watts x 1 channel Total RMS power output: 1500 watts LED power (green) / protect (red) light indicator Wired bass level remote control included 1 pair of pre-amp outputs Signal sensing remote turn-on Thermal, overload, and speaker short protection Pulse Width Modulated MOSFET power supply Preamp RCA outputs to daisy chain multiple amps Dual speaker terminals simplify hooking multiple speakers Heavy duty aluminum alloy heat-sink Low Level Input sensitivity: 0.2 - 6 volts Variable low-pass filter: 35 - 300 Hz Subsonic filter: 10 - 50 Hz Variable Bass Boost: 0 - 12 dB Fuse Rating: 75A 4 AWG gauge amplifier wiring kit is recommended for installation Dimensions: 16.5" L x 9.75" W x 2.50" H Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Precision Power TM1.2000D 2000W Peak Class D Trax Micro Series Monoblock Amplifier General Features: Trax Micro Series Class D Stable Monoblock Amplifier Total peak power output: 2000 watts LED Power/Protect Light Wired bass level remote control included Speaker-level (high-level) inputs Signal sensing remote turn-on Thermal, overload, and speaker short protection Compact and space saving design Fits behind truck, seats, or wheel wells Input sensitivity: Low level: 0.25 - 8 volts High level: 0.25 - 8 volts Frequency Response: 10 - 250 Hz Variable low-pass filter: 32 - 350 Hz Subsonic filter: 15 - 50 Hz Variable Bass Boost: 0 - 12 dB Fuse Rating: 50A 4 AWG gauge amplifier wiring kit is recommended for installation Dimensions: L x W x H Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Precision Power TM4.2000D 2000W Peak Class D Trax Micro Series 4-Channel Micro Car Amplifier General Features: Trax Micro Series Class D Stable 4-Channel Amplifier RMS Power Rating: 4 ohm: 100 watts x 4 channel 2 ohm: 150 watts x 4 channel Bridged: 400 watts x 2 channel @ 4 ohm Total power output: 2000 watts LED power and protect light Speaker-level (high-level) inputs 2 pairs of pre-amp outputs Signal-sensing remote turn-on 3-way protection circuitry (thermal, overload, and speaker short protection) Input sensitivity: Low level: 250 mV - 8 volts High level: 250 mV - 8 volts Frequency Response: 10 - 250 Hz Fuse Rating: 50A 1/0 AWG gauge amplifier wiring kit is recommended for installation Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Precision Power TRAX1.3000D 3000W Max (1500W RMS) Trax Series 2 ohm Stable Monoblock Class-D Amplifier General Features: Precision Power Trax Series TRAX1.3000D Class-D 2 ohm Stable Monoblock Amplifier RMS Power Rating: 4 ohms: 1000 watts x 1 chan. 2 ohms: 1500 watts x 1 chan. 1 ohm: _ watts x _ chan. Total power output: 3000 watts Pulse Width Modulated MOSFET power supply Wired remote bass level control included LED power (green) and protect (red) indicators Soft start turn-on Mono channel operation Preamp RCA outputs to daisy chain multiple amps 3-way protection circuitry (thermal, overload, and speaker short protection) Dual speaker terminals simplify the hookup of multiple speakers Heavy duty aluminum alloy heat-sink Input sensitivity: 200mV - 6V Variable low-pass filter: 32 - 300Hz Subsonic filter: 10 - 50Hz Variable Bass Boost: 0 to +12 dB bass boost at 50 Hz Fuse Rating: 25A x 3 Specifications: Power Specifications - Full Range Channels: RMS Power @ 4 ohms: 1000 watts x 1 channels RMS Power @ 2 ohms: 1500 watts x 1 channels Amplifier Specifications: Amplifier Series: Trax Amplifier Class: D Number of Channels: 1 - Mono Total Peak Power Output: 3000 watts Total RMS Power Output: 1500 watts Maximum Input Gauge Size: 4 AWG Minimum Impedance Unbridged: 2 ohms Speaker Level Inputs: No Preamp Outputs: 1 pair Built-in Crossover: Low-Pass (LP), Subsonic Low-Pass Crossover Frequency: 32 - 300 Hz Subsonic Filter: 10 - 50 Hz Bass Boost: 0 - 12 dB Bass/Gain Remote: Yes Fuse Rating: 25A x 3  Total Fuse Rating: 75 Strappable: Yes CEA-2006 Compliant: No Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Precision Power TRAX1.2000D 2000W Max (700W RMS) 2-ohm Stable Monoblock Class-D Car Amplifier General Features: Precision Power TRAX1.2000D Class-D 2 ohm Stable Monoblock Amplifier RMS Power Rating: 4 ohms: 700 watts x 1 chan. 2 ohms: 1000 watts x 1 chan. 1 ohm: ------------N/A------------ Total power output: 2000 watts Pulse Width Modulated MOSFET power supply Wired remote bass level control included LED power (green) and protect (red) indicators Soft start turn-on Mono channel operation Speaker-level (high-level) inputs Preamp RCA outputs to daisy chain multiple amps 3-way protection circuitry (thermal, overload, and speaker short protection) Dual speaker terminals simplify the hookup of multiple speakers Heavy-duty aluminum alloy heat-sink Input sensitivity: 200 mV - 6 V Variable low-pass filter: 32 - 300 Hz Subsonic filter: 10 - 50 Hz Variable Bass Boost: 0 to +12 dB bass boost Fuse Rating: 25A x 2 Dimensions: 9.75"W x 14"L x 2.5"H Specifications: Amplifier Class: D Number of Channels: 1 - Mono Total Peak Power Output: 2000 watts Total RMS Power Output: 1000 watts Maximum Input Gauge Size: 4 AWG Minimum Impedance Unbridged: 2 ohms Minimum Impedance Bridged: Not Bridgeable Speaker Level Inputs: No Preamp Outputs: 1 pair Built-in Crossover: Low-Pass (LP), Subsonic Low-Pass Crossover Frequency: 32 - 300 Hz Subsonic Filter: 1 - 50 Hz Bass Boost: 0 - 12 dB Bass/Gain Remote: Yes Fan Cooled: No Fuse Rating: 25A x 2  Total Fuse Rating: 50 Strappable: Yes CEA-2006 Compliant: No Amp Bluetooth Connectivity: No Hi-Res Certified: No Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Precision Power TRAX1.1500D 1500W Peak (750W RMS) Class D Trax Series Monoblock Amplifier General Features: Trax Series Class D 2 ohm Stable Monoblock Amplifier RMS Power Rating: 4 ohm: 500 watts x 1 channel 2 ohm: 750 watts x 1 channel Total RMS power output: 750 watts Power and protect LED light indicator Wired bass level remote control included 1 pair of pre-amp outputs Signal sensing remote turn-on Thermal, overload, and speaker short protection Input sensitivity:0.2 - 6 volts Total Harmonic Distortion (THD): 1% Variable low-pass filter: 32 - 300 Hz Subsonic filter: 10 - 50 Hz Variable Bass Boost: 0 - 12 dB Fuse Rating: 70A 4 AWG gauge amplifier wiring kit is recommended for installation Dimensions: 15" L x 9.75" W x 2.5" H Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Precision Power TRAX5.2200D 2200W Max (1100W RMS) Trax Series 2-ohm Stable 5 Channel Class-D Amplifier General Features: Precision Power Trax Series TRAX5.2200D Class-D Full Range 2 ohm Stable 5-Channel Amplifier RMS Power Rating: 4 ohms: 100 watts x 4 chan., 350W x Sub chan. 2 ohms: 150 watts x 4 chan., 500W x Sub chan. 1 ohm: ------------N/A------------ Bridged, 4 ohms: 300 watts x 2 chan., 500W x Sub chan. Total power output: 2200 watts Pulse Width Modulated MOSFET power supply Wired remote bass level control included LED power (green) and protect (red) indicators Soft start turn-on 5/3 channel operation 3-way protection circuitry (thermal, overload, and speaker short protection) Dual speaker terminals simplify the hookup of multiple speakers Heavy duty aluminum alloy heat-sink Input sensitivity: 200mV - 6V Variable high-pass filter: 80- 1200 Hz, 12 dB/octave Variable low-pass filter: 50 - 250 Hz, 12 dB/octave Variable Bass Boost: 0 to +12 dB bass boost Fuse Rating: 40 A x 2 Specifications: Power Specifications - Full Range Channels: RMS Power @ 4 ohms: 100 watts x 4 channels RMS Power @ 2 ohms: 150 watts x 4 channels Bridged RMS Power: 300 watts x 2 channels Power Specifications - Subwoofer Channel: RMS Power @ 4 ohms: 300 watts x 1 channels RMS Power @ 2 ohms: 500 watts x 1 channels Amplifier Specifications: Amplifier Series: Trax Amplifier Class: D Number of Channels: 5 Total Peak Power Output: 2200 watts Total RMS Power Output: 1100 watts Maximum Input Gauge Size: 4 AWG Minimum Impedance Unbridged: 2 ohms Minimum Impedance Bridged: 4 ohms Speaker Level Inputs: No Preamp Outputs: No Built-in Crossover: Low-Pass (LP), High-Pass (HP) High-Pass Crossover Frequency: 80 - 1200 Hz Low-Pass Crossover Frequency: 50 - 250 Hz Bass Boost: 0 - 12 dB Bass/Gain Remote: Yes Fuse Rating: 40A x 2  Total Fuse Rating: 80 CEA-2006 Compliant: No Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Precision Power TRAX4.1600D 1600W Max (400W RMS) Trax Series 2-ohm Stable 4 Channel Class-D Car Amplifier General Features: Precision Power Trax Series TRAX4.1600D Class-D Full Range 2 ohm Stable 4-Channel Amplifier RMS Power Rating: 4 ohms: 125 watts x 4 chan. 2 ohms: 200 watts x 4 chan. 1 ohm: ------------N/A------------ Bridged, 4 ohms: 400 watts x 2 chan. Total power output: 1600 watts Pulse Width Modulated MOSFET power supply LED power (green) and protect (red) indicators Soft start turn-on 4/3/2 channel operation Preamp RCA outputs to daisy chain multiple amps 3-way protection circuitry (thermal, overload, and speaker short protection) Heavy-duty aluminum alloy heat-sink Variable high-pass filter: 120 - 3000 Hz Variable low-pass filter: 50 - 250 Hz Fuse Rating: 35A x 2 Dimensions: 9.75"W x 13"L x 2.5"H Specifications: Amplifier Series: Trax Amplifier Class: D Number of Channels: 4 Total Peak Power Output: 1600 watts Total RMS Power Output: 400 watts Maximum Input Gauge Size: 8 AWG Minimum Impedance Unbridged: 2 ohms Minimum Impedance Bridged: 4 ohms Preamp Outputs: 1 pair Built-in Crossover: Low-Pass (LP), High-Pass (HP) High-Pass Crossover Frequency: 120 - 3000 Hz Low-Pass Crossover Frequency: 50 - 250 Hz Fuse Rating: 35A x 2  Total Fuse Rating: 70 Strappable: Yes CEA-2006 Compliant: No Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Precision Power TRAX4.1200D 1200W Max (600W RMS) Series 2-ohm Stable 4-Channel Class-D Amplifier General Features: Precision Power Trax Series TRAX4.1200D Class-D Full Range 2 ohm Stable 4-Channel Amplifier RMS Power Rating: 4 ohm: 100 watts x 4 chan. 2 ohm: 150 watts x 4 chan. 1 ohm: ------------N/A------------ Bridged, 4 ohm: 300 watts x 2 chan. Total power output: 1200 watts Pulse Width Modulated MOSFET power supply LED power (green) and protect (red) indicators Soft start turn-on 4/3/2 channel operation Preamp RCA outputs to daisy chain multiple amps 3-way protection circuitry (thermal, overload, and speaker short protection) Dual speaker terminals simplify the hookup of multiple speakers Heavy duty aluminum alloy heat-sink Input sensitivity: 200mV - 6V Variable high-pass filter: 120 - 3000 Hz Variable low-pass filter: 50 - 250 Hz Fuse Rating: 35 A x 2 4-gauge power and ground wiring is recommended for installation. Contact us for information regarding a discount on select amplifier kits from our website when purchased together with this amplifier. Click here for our contact information. Dimensions: 9.75"W x 11.75"L x 2.5"H Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.