2-Channel Amplifiers (58)

AUTOTEK MM1525-2D The MEAN MACHINE 1,500-Watt 2-Channel Compact Class D Amp 1,500-Watt Max Power 2 Channels X 750 Watts At 2 Ohms 2 Channels X 375 Watts At 4 Ohms 1 Channel Mono Bridged X 1,500 Watts Aftermarket Class D Amp Replaces Or Supplements Vehicle’S Existing Oem Amp To Power Car’S Stereo Speakers Drives Additional Power With A Small Footprint Frequency Response: 10 Hz To 22 Khz Total Harmonic Distortion (Thd) Less Than 0.05% Road Worthy Tcid (Twin Coil Isolation Design) And Pro-Fi High Speed Mosfets Bring Extreme Power With High Sound Quality And Minimum Distortion Levels Heavy-Duty Aluminum Alloy Heatsink With Illuminated Logo Adds A Vibrant Display And Showcase For Every Car Audio Installation Nickel-Plated Brass Connection With Hex Set Screw Terminals For Secure Connection While Resisting Corrosion Angled Allen Key Connectors Provide Easy Access For Hand Tools For Quick And Secure Connections Maximum Low Voltage Signal From Source Unit Comes Into Amp Through Low Voltage Circuit Which Delivers Minimal Distortion Through Amplification Process Rca Preamp Audio Outputs And Speaker Level Audio Inputs Rca Inputs And Outputs Provide Highest Sound Quality Connection Full-Range Signal Pass Through Output Allows Additional Amps To Be Run From The "Output" Rca Connections Which Minimize The Need For Additional Cables Running The Length Of The Vehicle, Minimizing Noise Onboard Variable Electronic Crossover 12 Db Per Octave Built-In Bass Control Amp Variable High Pass And Low Pass: 40 Hz To 400 Hz High Energy Pulse Width Modulated Power Supply Delivers Power With Minimal Impact On Electrical System Monitor-Overload And Speaker-Short Protection With Lighted Indicators On Amp End Panel Power Terminal 12-Volt/Gnd: 4 Awg Speaker Terminal Wire Gauge: 12 Awg Amp Fusing: External 50 Amps Dimensions: 11 In. X 7 In. X 3.25 In. Includes Mounting Hardware And Manual  WARNING - California Proposition 65  

AUTOTEK MM-2025.2D 2000 Watt Compact Bridgeable 2 Channel Amplifier   2,000-Watt Max Power 2 Channels X 1,000 Watts At 2 Ohms 2 Channels X 500 Watts At 4 Ohms 1 Channel Mono Bridged X 2,000 Watts At 4 Ohms Aftermarket Class D Amp Replaces Or Supplements Vehicle’S Existing Oem Amp To Power Car’S Stereo Speakers Drives Additional Power With A Small Footprint Can Operate In 2-Channel Or Bridged Mono Mode Frequency Response: 10 Hz To 22 Khz Total Harmonic Distortion (Thd) Less Than 0.05% Road Worthy Tcid (Twin Coil Isolation Design) And Pro-Fi High Speed Mosfets Bring Extreme Power With High Sound Quality And Minimum Distortion Levels Heavy-Duty Aluminum Alloy Heatsink With Illuminated Logo Adds A Vibrant Display And Showcase For Every Car Audio Installation Nickel-Plated Brass Connection With Hex Set Screw Terminals For Secure Connection While Resisting Corrosion Angled Allen Key Connectors Provide Easy Access For Hand Tools For Quick And Secure Connections Maximum Low Voltage Signal From Source Unit Comes Into Amp Through Low Voltage Circuit Which Delivers Minimal Distortion Through Amplification Process Rca Preamp Audio Outputs And Speaker Level Audio Inputs Rca Inputs And Outputs Provide Highest Sound Quality Connection Full-Range Signal Pass Through Output Allows Additional Amps To Be Run From The "Output" Rca Connections Which Minimize The Need For Additional Cables Running The Length Of The Vehicle, Minimizing Noise Onboard Variable Electronic Crossover 12 Db Per Octave Built-In Bass Control Amp Variable High Pass And Low Pass: 40 Hz To 400 Hz High Energy Pulse Width Modulated Power Supply Delivers Power With Minimal Impact On Electrical System Monitor-Overload And Speaker-Short Protection With Lighted Indicators On Amp End Panel Power Terminal 12-Volt/Gnd: 4 Awg Speaker Terminal Wire Gauge: 12 Awg Amp Fusing: External 100 Amps Dimensions: 11 In. X 7 In. X 3.25 In. Includes Mounting Hardware And Manual  WARNING - California Proposition 65  

AUTOTEK MM-3025.2D 3000 Watt Compact Bridgeable 2 Channel Amplifier   3,000-Watt Max Power 2 Channels X 1,500 Watts At 2 Ohms 2 Channels X 750 Watts At 4 Ohms 1 Channel Mono Bridged X 3,000 Watts At 4 Ohms Aftermarket Class D Amp Replaces Or Supplements Vehicle’S Existing Oem Amp To Power Car’S Stereo Speakers Drives Additional Power With A Small Footprint Can Operate In 2-Channel Or Bridged Mono Mode Frequency Response: 10 Hz To 22 Khz Total Harmonic Distortion (Thd) Less Than 0.05% Road Worthy Tcid (Twin Coil Isolation Design) And Pro-Fi High Speed Mosfets Bring Extreme Power With High Sound Quality And Minimum Distortion Levels Heavy-Duty Aluminum Alloy Heatsink With Illuminated Logo Adds A Vibrant Display And Showcase For Every Car Audio Installation Nickel-Plated Brass Connection With Hex Set Screw Terminals For Secure Connection While Resisting Corrosion Angled Allen Key Connectors Provide Easy Access For Hand Tools For Quick And Secure Connections Maximum Low Voltage Signal From Source Unit Comes Into Amp Through Low Voltage Circuit Which Delivers Minimal Distortion Through Amplification Process Rca Preamp Audio Outputs And Speaker Level Audio Inputs Rca Inputs And Outputs Provide Highest Sound Quality Connection Full-Range Signal Pass Through Output Allows Additional Amps To Be Run From The "Output" Rca Connections Which Minimize The Need For Additional Cables Running The Length Of The Vehicle, Minimizing Noise Onboard Variable Electronic Crossover 12 Db Per Octave Built-In Bass Control Amp Variable High Pass And Low Pass: 40 Hz To 400 Hz High Energy Pulse Width Modulated Power Supply Delivers Power With Minimal Impact On Electrical System Monitor-Overload And Speaker-Short Protection With Lighted Indicators On Amp End Panel Power Terminal 12-Volt/Gnd: 4 Awg Speaker Terminal Wire Gauge: 12 Awg Amp Fusing: External 150 Amps Dimensions: 12.75 In. X 7 In. X 3.25 In. Includes Mounting Hardware And Manual  WARNING - California Proposition 65  

AUTOTEK MM2020.2 2000W Max (1000W RMS) Mean Machine Series 4 ohm Stable 2-Channel Class-A/B Amplifier Autotek Mean Machine MM2020.2Class-A/B Full Range 4-Ohm Stable 2-Channel AmplifierRMS Power Rating:4 ohms: 500 watts x 2 chan.2 ohms: 1000 watts x 2 chan.1 ohm: ------------N/A------------Bridged, 4 ohms: 2000 watts x 1 chan.Total power output: 2000 wattsCEA-2006 Compliant AmplifierPulse Width Modulated MOSFET power supplyLED power (green) and protect (red) indicatorsSoft start turn-on2 or Mono channel operationSpeaker-level (high-level) inputsPreamp RCA outputs to daisy chain multiple amps3-way protection circuitry (thermal, overload, and speaker short protection)Dual speaker terminals simplify the hook up of multiple speakersHeavy duty aluminum alloy heat-sinkVariable Voltage:6V-0.2VFrequency Response: 30- 12000 HzTotal Harmonic Distortion (THD): <0.05%Signal to Noise Ratio: >90dBVariable high-pass filter: 60 - 1200 Hz, 12 dB/octaveVariable low-pass filter: 30 - 250 Hz, 12 dB/octaveVariable Bass Boost: 0 to +9 dB bass boost at 50 HzFuse Rating: 30A x 24 gauge power and ground wiring is recommended for installation. Contact us for information regarding a discount on select amplifier kits from our website when purchased together with this amplifier. Click Here for our contact information.Authorized Internet Dealer1-year Manufacturer's Warranty

Autotek TA-2055.2 Autotek 2000 Watts TA Two Channel Car Audio Amplifier. Product Details: Autotek TA Series Class A/B 2 ohms Stable 2-Channel Amplifier RMS Power Rating: 4 ohms: 500 watts x 2 channel 2 ohms: 1000 watts x 2 channel Bridged, 4 ohms: 2000 watts x 1 channel Total power output: 1000 watts Amp Tone Control / Parametric EQ: Built-in Bass Control Pulse Width Modulated MOSFET power supply LED Power/Protect Light Speaker-level High Level Inputs Output Connections Nickel Plated Brass Connection 3-way protection circuitry (thermal, overload, and speaker short protection) Frequency Response: 10 - 500 Hz Variable high-pass filter: 120 - 3,000 Hz, 24 dB/octave Variable low-pass filter: 50 - 250 Hz, 24 dB/octave Variable Bass Boost: 0 - 12 dB bass boost at 50 Hz Fuse Rating: 80 12 AWG gauge power and ground wiring is recommended for installation. Dimensions: 4" W x 15" L x 11.75" H Authorized Internet Dealer 1-year Manufacturer's Warranty ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate T400X2ad Power 400 Watt Class-AD 2-Channel Amplifier Rockford Fosgate's Power Series T400X2ad 2-channel amplifier can send each of your speakers up to 200 watts RMS, or you can use this tiny powerpack to run a sub with up to 400 watts. A dual-fan forced air cooling system keeps this sturdy little amp from overheating, so it can play hard for a long, long time. Class AD: accurate and powerful Rockford Fosgate uses their proprietary Class AD amplifier technology, combining the high fidelity of a Class A system with the high efficiency of their special Class D technology, to bring you this ultra-efficient, high-output amplifier. In other words, this compact amp produces more power with less current draw from your vehicle's charging system than most other amps on the road today. Rockford Fosgate's high-tech solutions yield more power Power Series amplifiers actively monitor speaker performance using Rockford Fosgate's Constant Power technology. A speaker's impedance naturally fluctuates as it performs, fighting against your amp's output. So, just like your cruise control increases the engine's RPM to maintain your car's speed uphill, Constant Power maintains this amp's output by increasing its internal voltage and current flow when the speaker's impedance rises. This results in up to a 25% increase in the amp's total power output. T400X2ab control panel with clip lights Easy to set for optimum performance Rockford Fosgate's C.L.E.A.N. technology (Calibrated Level Eliminates Audible Noise) setup system ensures your music will sound as clean and powerful as possible. It works like this: first download the SET UP from Rockford Fosgate, then play the tone, adjust the receiver volume until a red clip light on the amp goes out, then turn the amp gain up until a blue light comes on. It's that simple — your amplifier will be perfectly set to match your receiver's output. When your receiver reaches maximum clean volume, you'll get maximum clean power from your Power amp. At quiet listening levels, you'll hear less background noise and more of your music. Clip lights If that blue light turns solid red while you're playing music, the amp's telling you that your source is distorting and you should turn it down, or risk damage to your gear. The optional PLC2 remote level control also doubles as a clip indicator, so you can see from the front seat if your music's clipping. Product highlights: 2-channel car amplifier 200 watts RMS x 2 at 2 to 4 ohms 400 watts RMS x 1 bridged output at 4 ohms (4-ohm stable in bridged mode) CEA-2006 compliant Features: Class AD amplifier design Constant Power technology maintains full output power despite impedance changes C.L.E.A.N. gain setup system includes clip lights and link to Rockford Fosgate's setup tones differential input circuitry helps eliminate hum dual-fan forced induction cooling variable high- and low-pass filters (50-250 Hz, 12 dB/octave) variable Punch EQ (bass/treble boost: 0-18 dB at 45 Hz, 0-14 dB at 12,500 Hz) optional PLC2 Punch Level Control wired remote with clip light available More Info: preamp and speaker-level inputs signal-sensing turn-on with speaker-level inputs eliminates the need for a remote turn-on lead 8-gauge power and ground leads and a 60-amp fuse recommended — wiring and hardware not included with amplifier no onboard fuses — when installing multiple amps in a system, an additional 60-amp in-line fuse between the distribution block and the amplifier is recommended 7"W x 1-15/8"H x 4-1/4"D warranty: 2 years (extends to 3 years when purchased with a Rockford Fosgate RFK8, RFK8i, or RFK4D amp wiring kit) ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Punch P300X2 300W RMS Punch Series 2-Channel Stereo Class AB Car Power Amplifier The Punch P300X2 is a 2-channel stereo amplifier capable of producing 150 Watts into each channel at 2-Ohms. The P300X2 amplifier is great to drive a pair of coaxial speakers, component speakers, or a single subwoofer. The amplifier can also be run in stereo/mono mode simultaneously when using passive crossovers (not supplied) on all speakers. With proven PUNCH technology, the P300X2 delivers real Rockford Fosgate power from a small design and is flexible to accommodate any moderately sized system. General Features: Punch Series 2-Channel Class AB Car Amplifier RMS Power Rating: 4 ohms: 100 watts x 2 Channel 2 ohms: 150 watts x 2 Channel Bridged, 4 ohms: 300 watts x 1 chan. CEA-2006 compliant amplifier Features C.L.E.A.N. Set-up with input/output clip detection and indicator LEDs MOSFET power supply Muted turn on Cast aluminum heatsink 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protect indicators Nickel-plated captive C-clamp terminals Ultra-efficient Class BD circuitry to maximize amplifier power efficiency On-board differential inputs eliminate noise picked up by the signal cable Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately) MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowers the operating temperature and potential for noise - similar to circuit boards designed by aerospace manufacturers Input sensitivity: 150mV - 12V What is in the box: 2-Channel amplifier Four 1-1/2" Screws 5mm Allen wrench Quick setup instructions Certificate of Performance Rockford Fosgate Punch P300X2 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Rockford Fosgate Punch PBR300X2 300 Watts Punch Series Boosted Rail Compact 2-Channel Amplifier The Punch PBR300X2 is a 2-channel stereo amplifier capable of producing 150 Watts into each channel at 2-Ohms. The PBR300X2 amplifier is great to drive a pair of coaxial speakers, component speakers, or a single subwoofer. The amplifier can also be run in stereo/mono mode simultaneously when using passive crossovers (not supplied) on all speakers. With proven PUNCH technology, the PBR300X2 delivers real Rockford Fosgate power from a small design and is flexible to accommodate any moderately sized system. General Features: Punch Series BR Monoblock Car Amplifier RMS Power Rating @ 4 ohms: 100 watts x 2 channel RMS Power Rating @ 2 ohms: 150 watts x 2 channel 4 ohm Bridged: 300 watts x 1 chan. Features Rockford Fosgate Class-BR Topology CEA-2006 compliant amplifier Ultra-compact chassis MOSFET output stage Boosted Rail amp technology Convection cooling design Extruded aluminum heat sink Low-level RCA input connection High-level speaker input connection Detachable Compression Terminals 12dB / Octave Butterworth crossover Selectable crossover mode: LP/AP/HP LED power (blue) and protect (red) indicators Variable 4-6 volt hi-level DC offset voltage input turn-on control Features MEHSA3 (Maximum Efficiency Heat Sink Application - gen. 3) Perfect for smaller stealth installations Great for motorcycles and recreational vehicles Optional Remote Punch EQ provides 0dB to +18dB @ 45Hz 16 Gauge speaker wire output terminals 10-gauge OFC power and ground wiring are recommended for installation. 1-year Manufacturer's Warranty What is in the box: 2-Channel amplifier 6" Speaker output harness (Molex plug on one end and tinned bare wire on the other) 12" Input harness (Molex plug on one end and female stereo RCA jacks on the other) Quick setup instructions Certificate of Performance Rockford Fosgate Punch PBR300X2 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov