Car Subwoofers (324)

Alpine S-W10D4 1800W Max (600W RMS) 10" S-Series Dual 4 Ohm Car Subwoofer Alpine introduces the all-new S-Series Subwoofers; their unique design substantially improves bass output and provides installation versatility. Each S-Series subwoofer uses a custom-stamped steel frame and is available in twelve, ten, and eight-inch. These high-strength frames were designed to withstand the rigors of the improved S-Series motor. They have frame leg vents, a vented back plate to help cool the subwoofer voice coil and motor parts, and a shallow design to help fit in smaller spaces. The S-Series Subwoofers incorporate two strontium ferrite magnets stacked together, providing increased motor strength and excursion, ultimately delivering an accurate bass to your music. The convenient push-type insert terminals with a dual voice coil jumper system will significantly reduce installation time. Just strip the speaker insulation at the wire end, then insert the bare wire into the hole of the spring-loaded push terminal. At the same time, the concealed mount gasket system creates a clean, finished appearance for any vehicle. General Features: 10" 4 ohm S-Series (Type-S) Subwoofer RMS Power Handling: 600 watts Peak Power Handling: 1800 watts  Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 4-11/16" Cutout diameter: 8-13/16 Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 33 Hz Authorized Dealer 1-year Manufacturer's Warranty What's in the S-W10D4 package: S-W10D4 owner's manual One 10" Dual 4-ohm voice coil subwoofer Two 3" jumper cables Subwoofer Application Guide Online product registration information Warranty information ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

2 Alpine S-W10D2 1800W Max (600W RMS) 10" S-Series Dual 2 Ohm Car Subwoofer Alpine introduces the all-new S-Series Subwoofers; their unique design substantially improves bass output and provides installation versatility. Each S-Series subwoofer uses a custom-stamped steel frame and is available in twelve, ten, and eight-inch. These high-strength frames were designed to withstand the rigors of the improved S-Series motor. They have frame leg vents, a vented back plate to help cool the subwoofer voice coil and motor parts, and a shallow design to help fit in smaller spaces. The S-Series Subwoofers incorporates two strontium ferrite magnets stacked together, providing increased motor strength and excursion, ultimately delivering an accurate bass to your music. The convenient push-type insert terminals with a dual voice coil jumper system will significantly reduce installation time. Just strip the speaker insulation at the wire end, then insert the bare wire into the hole of the spring-loaded push terminal. At the same time, the concealed mount gasket system creates a clean, finished appearance for any vehicle. General Features: 10" 2 ohm S-Series (Type-S) Subwoofer RMS Power Handling: 600 watts Peak Power Handling: 1800 watts  Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 4-11/16" Cutout diameter: 8-13/16 Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 33 Hz Authorized Dealer 1-year Manufacturer's Warranty What is in the S-W10D2 package: S-W10D2 owner's manual One 10" Dual 2-ohm voice coil subwoofer 1 Rubber concealing ring Two 3" jumper cables (each has a single banana connector on each end) Subwoofer Application Guide Online product registration information Warranty Information ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

2 Alpine S2-W8D4 900W Max (300W RMS) 8" Type S Series Dual 4 Ohm Car Subwoofer ADD BASS TO PRACTICALLY ANY VEHICLE Don’t you think you have room for a subwoofer? Think again. The new S-W8D2 and S-W8D4 8” S-Series subwoofers have a shallow mounting depth of just 3-3/4” and can be used in a sealed box enclosure as small as .15 cubic feet. It is perfect for under-seats, behind-rear bench seats in trucks, or even for some door applications. General Features: 8" 4 Ohm Type S Series Subwoofer Power Handling: Peak: 900 watts RMS: 300 watts Recommended Power Range: 150 - 300 Watts Kevlar Reinforced Pulp Cone HAMR Santoprene Rubber Surround Progressive Spider with Reinforced Layer Tinsel Leads Compound Radius Curve Extended Pole Geometry Perimeter Vented Frame with Airflow Management System 10 AWG Push Terminals 35mm Underhung Voice Coils Concealed Mount Gasket 34oz Ferrite Magnet Top-mount depth: 3-3/4" Cutout diameter: 6-7/8" Frequency Response: 34-200Hz Authorized Dealer 1-year Manufacturer's Warranty Priced Individually What's in the S2-W8D4 package: Two 8" Dual 4-ohm voice coil subwoofer Alpine S-W8D4 owner's manual 1 Rubber concealing ring Two 3" jumper cables Subwoofer Application Guide Online product registration information Warranty information  Important Notice!  Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine SWT-10S2 1000W Peak 10" SWT Series Single 2-ohm Shallow Mount Subwoofer Right size, Right sound. Here's a big bass breakthrough for truck lovers. Alpine engineered their SWT-10S2 10" subwoofer to go behind your seat and sound especially good in the limited space of a truck cab. This deep-sounding, high-performance sub works well in shallow enclosures that'll fit behind or under the seat in your truck. A "high amplitude" surround allows more cone travel than a regular sub, so the SWT-10S2 can push more air and play louder. Airflow-insured subs get hot as they play, and the heat usually gets vented away via a port in the back of the sub's pole piece. Alpine recessed the pole port and added cooling air vents on the sides of the frame, allowing you to use an enclosure with an inside clearance of as little as 4-3/16" without blocking critical airflow. General Features: 10" SWT Series Single 2-ohm Shallow Mount Truck Subwoofer Peak Power Handling: 1,000 watts RMS Power Handling: 350 watts Recommended Power Range: 100W - 350W Poly-Mica Dust Cap & Pulp-Kevlar Polyurethane Foam Surround H.A.M.R. Surround Technology Spiral Cut Aluminum Former 65mm Voice Coil with High-Temp 4-Layer SVC Winding 8AWG Push Terminals Top-mount depth: 4-3/16" Mounting Diameter: 8-15/16'' Frequency Response: 30 - 200 Hz Sensitivity: 84.8 dB Authorized Dealer 1-year Manufacturer's Warranty What is in the SWT-10S2 package: SWT-10S2 owner's manual 10" Thin-mount subwoofer Online product registration information Warranty information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Punch P3D4-10 P3 Series DVC 4-Ohm 10-Inch 500-Watt RMS 1000 Watts Peak Subwoofer The Rockford Fosgate P3D4-10 is the best-performing Punch series subwoofer. The P3 subwoofers now feature anodized aluminum cones and dust caps along with unique spider venting to keep the motor cooler than previous versions. These subs feature VAST technology to increase surface cone area to 25% and a Flex Fit basket for extreme installations. A new hybrid stamp-cast basket offers the best of both worlds by providing super strength while minimizing weight and resonance. 10" Punch P3 Series Dual 4 Ohm Subwoofer General Feature: 10" Punch P3 Series Dual 4 Ohm Subwoofer Power Handling: Peak: 1,000 watts Power Handling: RMS: 500 watts Impedance: 4 ohm Anodized aluminum heat sinking cone & dust cap for strength and durability Tall profile true Santoprene vertical attach surround technique increases a speaker's effective radiating cone area Dual tear & fatigue resistant linear poly cotton spiders Optimized motor magnetics with extended pole and bumped backplate Fatigue-resistant and reduced-strain stitched tinsel leads Multipoint high temp/strength neck joint bonding technique Sturdy 16-gauge compound bend frame geometry Semi-Flexible PVC removable protective motor cover Custom insulated compression input terminal assembly Proprietary spider venting/cooling technique Decorative die-cast trim ring Custom 10-AWG nickel-plated push terminals High-temperature 4-layer 2-1/2" voice coil with spun-laced Nomex insulating reinforcement collar Double-stacked ferrite magnet structure Frequency response: 28-250 Hz Sensitivity: 82 dB Xmax: 13.9 mm Mounting Depth: 6-1/4" Cutout Diameter: 9-1/8" Magnet Weight: 81 oz Frequency Response: 28 - 250 Hz Xmax: 15.9mm Sensitivity: 82 dB @ 1 watt / 1 meter Recommended Ported Enclosure: 1.40ft³ Recommended Sealed Enclosure: 0.59ft³ Magnet Weight: 81 oz Frequency Response: 28 - 250 Hz Xmax: 15.9mm Sensitivity: 82 dB @ 1 watt / 1 meter Recommended Ported Enclosure: 1.40ft³ Recommended Sealed Enclosure: 0.59ft³ Matching Amplifiers: (one subwoofer) Rockford Fosgate R750-1D, Parallel @2ohms Rockford Fosgate P1000X1bd, Parallel @2ohms Rockford Fosgate R500X1D, Parallel @2ohms Matching Amplifier: (two subwoofers) Rockford Fosgate P1000X1bd, Parallel @1ohm Rockford Fosgate R1200-1D, Parallel @1ohm Authorized Internet Dealer 1-year Manufacturer's Warranty ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca

2 Alpine R2-W12D4 2250W Max (750W RMS) 12" R-Series Dual 4-Ohm Car Subwoofer The new 2022 R-Series subwoofers are here - drawing from decades of Subwoofer engineering experience. They deliver deep, clean, accurate bass and feature Alpine’s HAMR Surround for maximum cone excursion, delivering tons of bass output. The new ceramic dust cap is lightweight and rigid, keeping distortion at an absolute minimum. The enlarged motor structure ensures better woofer control for a strong, clean bass response. General Features: 12" Dual 4 ohm Type-R Subwoofer Peak Power Handling: 2250watts RMS Power Handling: 750 watts Recommended power range: 300 - 750W RMS CTA-2031 compliant power ratings Parabolic pulp/kevlar cone H.A.M.R. surround Polypropylene, mica, and talc dust cap Reinforced cone neck and spider joint Cast aluminum frame with integral shorting sleeve 8AWG push terminals with VC configuration jumpers 2.6" High excursion overhung voice coil 127 oz. Strontium ferrite segmented magnet Top-mount depth: 6-3/8" Cutout diameter: 10-7/8" Frequency Response: 24 - 200Hz Sensitivity: 84.3dB Resonance Frequency (Fs): 27Hz Authorized Dealer 1-year Manufacturer's Warranty What's in the R2-W12D4 package: R2-W12D2 owner's manual One 12" Dual 4-ohm voice coil subwoofer Two 3" jumper cables R-Series Subwoofer Application Guide Online product registration information Warranty Information Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

2 Alpine R2-W12D2 2250W Max (750W RMS) 12" R-Series Dual 2-Ohm Car Subwoofer The new 2022 R-Series subwoofers are here - drawing from decades of Subwoofer engineering experience. They deliver deep, clean, accurate bass and feature Alpine’s HAMR Surround for maximum cone excursion, delivering tons of bass output. The new ceramic dust cap is lightweight and rigid, keeping distortion at an absolute minimum. The enlarged motor structure ensures better woofer control for a strong, clean bass response. General Features: 12" Dual 2 ohm Type-R Subwoofer Peak Power Handling: 2250watts RMS Power Handling: 750 watts Recommended power range: 300 - 750W RMS CTA-2031 compliant power ratings Parabolic pulp/kevlar cone H.A.M.R. surround Polypropylene, mica, and talc dust cap Reinforced cone neck and spider joint Cast aluminum frame with integral shorting sleeve 8AWG push terminals with VC configuration jumpers 2.6" High excursion overhung voice coil 127 oz. Strontium ferrite segmented magnet Top-mount depth: 6-3/8" Cutout diameter: 10-7/8" Frequency Response: 24 - 200Hz Sensitivity: 84.3dB Resonance Frequency (Fs): 27Hz Authorized Dealer 1-year Manufacturer's Warranty What's in the R2-W12D2 package: R2-W12D2 owner's manual One 12" Dual 2-ohm voice coil subwoofer Two 3" jumper cables R-Series Subwoofer Application Guide Online product registration information Warranty Information https://www.youtube.com/watch?v=ihjWBSOYVxE&t=179s Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine PWE-S8-WRA 8" Amplified Custom Fit for 2011-up Jeep Wrangler (4 doors) - Under Seat Plug and Play 120 Watt Amplified Subwoofer DISCREET, WITH A PUNCH The small but powerful PWE-S8-WRA consists of an 8-inch powered subwoofer with a built-in 120 watts amp, a bracket designed to bolt the subwoofer under the Wrangler driver’s seat, a remote bass knob and Wrangler-specific wiring harnesses for plug-and-play connection to your aftermarket or factory in-dash system. The powered subwoofer measures just 13.5” L x 9” W x 3” D, so you can add low, punchy, accurate bass to your Jeep without taking up usable storage space. SOUND CONTROL AT YOUR FINGERTIPS Subwoofer controls like Phase, Gain, LP Crossover, and Remote Sub Level are found on the side panel, or mount the remote bass knob on your dash and use it to make bass level adjustments easily.General Features: 8-inch Compact Powered Subwoofer System Compatible with 2011-Up Jeep Wrangler 4-door vehicles Plug-and-play installation Installs under the driver's seat Works with an Alpine or aftermarket head unit or with the factory Jeep radio Built-in 120 Watt Amplifier Strong and Durable cast aluminum enclosure Dimensions: 13.5"L x 3"D x 9"W Authorized Dealer 1-year Manufacturer's Warranty Note: Not compatible with the factory-equipped subwoofer system What's in the box: Amplified enclosure with one 8" subwoofer installed 80" Wiring harness (Power/ Ground/ Speaker level input) Wrangler radio T-Harness (with in-line fuse holder) Two 15 amp ATO fuses (one installed in the power wire fuse holder/ 1 spare) Remote level control with 15' cable attached (3.5mm mini-plug on end) Adhesive-backed hook and loop mounting fasteners (to mount the remote) 2 Wrangler mounting brackets Eight M4x10mm Machine screws (each with a flat washer and split lock washer) Four M6x10mm Machine screws Fifteen 7" Zip ties Installation instructions Owner's manual (English/ French/ Spanish) Warranty information Online product registration information System installation notice Alpine PWE-S8-WRA owner's manual ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine PSS-23WRA Powered Sound System Upgrade for 2018 - Up Jeep Wrangler Unlimited Powered System Upgrade for 2018-Up Jeep® Wrangler Unlimited JL TAKE YOUR WRANGLER’S SOUND BEYOND THE FACTORYEnjoy premium sound quality even with your JL’s top-off! The PSS-23WRA is a 300-watt powered system upgrade featuring a powered subwoofer, amplifier, and tweeters for the 2018-Up Jeep Wrangler Unlimited JL without the factory amplified system. The PSS-23WRA provides excellent sound performance whether the JL’s top is on or off.SOUND THAT WILL TURN HEADS WITH THE TOP ON OR OFFThe PWE-S8 subwoofer is engineered to load and disperse lower-frequency sound into the passenger’s footwell area to maximize bass extension throughout the Jeep for great sound with the top on or off. Included with the subwoofer is a remote bass knob so you can control the bass level from the convenience of your dashboard. The Included 4-channel amplifier more than doubles the power over the factory system allowing you to enjoy your tunes with the top off. EASY BOLT-IN INSTALLATIONThe PWE-S8 Powered Subwoofer and KTP-445U Power Pack Amplifier don’t take up much since they mount under the passenger’s seat. The two products come pre-connected for easy bolt-in installation with simple wire routing. Mounting brackets for the products are included as well.SIMPLE TWEETER REPLACEMENTThe SPR-10TW Component Tweeters replace the factory tweeters on the top of the dash. These high-performance tweeters add much-needed high-frequency response that is lacking in the factory Jeep JL systems. An EQ Ring improves the tweeter’s dispersion characteristics and delivers a wide, flat frequency response.WORKS WITH ANY RADIOThe included T-harness gets the necessary audio signal connections from behind the Wrangler’s radio, making installation a breeze. The PSS-23WRA is compatible with Alpine universal head units, the factory Jeep base radio, or other aftermarket radios. General Features: Complete Direct Fit Audio System Upgrade Compatible with 2018 - Up Jeep Wrangler Unlimited JL Compatible with models that don't have a factory-amplified system All installation hardware, such as speaker adapters and amplifier wiring, included CEA-2006 Compliant System 300 Watt RMS sound system The system consists of: 8" Powered Subwoofer Universal Power Pack Amplifier 2" Component Tweeters Tweeter Adapters Authorized Dealer 1-year Manufacturer's Warranty PWE-S8 Subwoofer Features: Peak: 240 watts RMS: 120 watts 8" woofer high-excursion cone built-in Class D amplifier frequency response: 32-150 Hz variable low-pass crossover (80-200 Hz) variable phase control (0-180 degrees) preamp- and speaker-level inputs Dimensions: 13-1/2"W x 3"D x 9"H KTP-445U Amplifier Features: RMS Power Rating: 4 ohms: 45 watts x 4 Channel 2 ohms: 45 watts x 4 Channel 4 ohms: 90 watts x 2 Channel (Bridged) Total RMS power output: 180 watts CEA-2006 compliant amplifier Increases the output of any head unit without having to install a full-size amplifier and amp install kit The Independent front/Rear gain switch is adjustable from high to low Runs off the receiver's power circuit High-Pass Filter: selectable 60/80/120 Hz @ 12 dB/octave Fast and simple installation 4-channel operation for four speakers Minimum impedance of 2 ohms Frequency response: 20-20,000 Hz Fuse Rating: 15A x 1 SPR-10TW Component Tweeters: 2" Type-R Series Car Tweeters Power Handling: Peak: 450 watts per pair / 225 watts each RMS: 150 watts per pair / 75 watts each Silk Dome tweeter construction 4 ohms impedance Copper-Clad Aluminum high-temperature voice coil 75% smaller external crossover filter removes harmful frequencies 4-way tweeter level attenuation High-grade Neodymium magnet structure Surface / Bottom / Flush Mountable CEA-2031 compliant speakers Sensitivity: 88dB Frequency response: 1,000-29,000 Hz Top-mount depth: 11/16" Vehicle Compatibility: JEEP 2018 - Up Wrangler Unlimited JL Compatible with Wrangler JL Models that don't have a factory amplified system What's in the box: KTP-445U amplifier PWE-S8 powered subwoofer (both pre-attached to vehicle mounting bracket) 7' Signal harness 12' Loomed power wire w/ inline 20A fuse 52-Pin t-harness Four 10" speaker to RCA harnesses Two SPR-10TW tweeters w/ integrated mounting plates and 8" wire loom w/ inline crossovers Remote bass-level control w/ attached 16' cable 3" Strip of hook-and-loop fastener Ten 6" wire-ties 1/2" Self-tapping screw Star-washer 2 Alpine logos Installation guide Warranty sheet Alpine PSS-23WRA owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.