

00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate Punch P1000X1bd
P1000X1bd Mono subwoofer amplifier 1,000 watts RMS x 1 at 1 ohm $499.99 $859.98
P1000X1bd Mono subwoofer amplifier 1,000 watts RMS x 1 at 1 ohm $499.99 $859.98
Rockford Fosgate Punch P1000X1bd Mono subwoofer amplifier 1,000 watts RMS x 1 at 1 ohm
The Punch P1000X1bd mono amplifier pumps out 1,000 Watts into a 1-Ohm load. The Class-BD technology produces bass more efficiently over traditional amps, and its frequency response is optimized for subwoofers. With its super-efficient Class-BD circuit topology, the P1000X1bd assures maximum BOOM for your buck! Due to its dedicated low-frequency response, this amplifier is optimized for mid-bass speakers or subwoofers only. No need to worry because its 1-ohm capability will easily drive a pair of 4-ohm DVC subwoofers or quad-configuration of 2-ohm DVC subwoofers.
General Features:
Punch BD Series Monoblock Class BD Car Amplifier
RMS Power Rating:
4 ohms: 300 watts x 1 channel
2 ohms: 500 watts x 1 channel
1 ohm: 1000 watts x 1 channel
CEA-2006 compliant amplifier
Features C.L.E.A.N. Set-up with the 10-step set-up procedure
w/ input/output clip detection and indicator LEDs
MOSFET power supply
Muted turn on
Cast aluminum heatsink
12dB/octave Butterworth crossover
Stealth top-mounted control panel
LED power, thermal, and protection indicators
Nickel-plated captive C-clamp terminals
Ultra-efficient Class BD circuitry to maximize amplifier power efficiency
On-board differential inputs eliminate noise picked up by the signal cable
Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator)
High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately)
MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span
Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances
Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low
DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowering the operating temperature and potential for noise - similar to circuit boards designed by aerospace manufacturers
Input sensitivity: 150mV - 12V
On-board Punch EQ with +18dB boost @ 45Hz.
Variable low-pass filter: 50-250 Hz
Selectable infrasonic filter: off / 28 Hz
Frequency response: 20 - 250 Hz
Total Harmonic Distortion: <1.0%
Dimensions: 13-5/16"L x 7-3/4"W x 2-3/8"H
8 AWG to 18 AWG speaker wire output terminals
4 gauge power and ground wiring is recommended for installation.
Authorized Internet Dealer
1-year Manufacturer's Warranty
What is in the P1000X1bd package:
P1000X1bd owner's manual
Mono subwoofer amplifier
Four 1-1/2" Self-tapping screws
5mm Allen wrench
Quick setup instructions
⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.


00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate Prime R2-750X1 Amplifier
750W Prime Series Monoblock Subwoofer Class D Amplifier $349.99 $379.99
750W Prime Series Monoblock Subwoofer Class D Amplifier $349.99 $379.99
Rockford Fosgate Prime R2-750X1 750W Prime Series Monoblock Subwoofer Class D Amplifier
Primed for performance, the R2-750X1 amplifier is a 750-watt, Class-D, capable of operating at 4Ω, 2Ω, or 1Ω mono. This amplifier is extremely efficient because of its Class-D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allow you to tune the bass for the desired level of the music.
Rockford Fosgate's R2 amplifiers are the building blocks for great audio systems, powerful enough to even DRIVE our Punch speakers and subwoofers. They have undergone an amazing upgrade by packing them with the latest features at an incredible value. Best of all, they are designed and engineered here in Tempe, Arizona.
General Features:
Rockford Fosgate Prime R2-750X1
RMS Power Rating: 4 ohms: 250 watts x 1 channel
RMS Power Rating: 2 ohms: 500 watts x 1 channel
RMS Power Rating: 1 ohm: 750 watts x 1 channel
Total power output: 500 watts
Balanced Differential Inputs with RCA Pass Through Outputs
High-Level Input Capable
Defeatable Auto Turn on Circuit
Features C.L.E.A.N. Set-up
Variable Input Gain adjustment level
R.L.C. Remote Level Control
Variable Infrasonic Filter
Continuously Variable On-Board Punch EQ
Top Mounted Control Panel
Short Circuit & Over Current Protection
CEA-2006 Compliant & CE Compliant
Full Range Class D
Rollback Protection
Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers
Input sensitivity: Low-Level: 150 mV - 4 V
Input sensitivity: High-Level: 450 mV - 12 V
Frequency Response: 20 Hz - 250 Hz
Total Harmonic Distortion (THD): >1%
Crossover Controls: Low-Pass: 50 Hz - 250 Hz
Crossover Controls: Sub Infrasonic: 15 Hz - 40 Hz
Recommended Fuse Rating: 120A
4-gauge power and ground wiring are recommended for installation.
Dimensions: "1.9" x "6.8" x "10.1"
Authorized Internet Dealer
1-Year Manufacturer's Warranty
What is in the R2-750X1 package:
Mono subwoofer amplifier
Wired Remote Level Control module
16' Remote cable (RJ-25 connector on both ends)
One 7" Speaker input harness
3mm Allen Hex key
Four 3/4" Screws
Two 1/2" Screws
5 Flat washers
1 Nut
Installation and Operation Instructions
Certificate of Performance
Rockford Fosgate contact information
Rockford Fosgate R2-500X1 owner's manual
⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.


00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate R2-500X1
Prime Series 500 Watt Monoblock Class-D Amplifier $279.99 $309.00
Prime Series 500 Watt Monoblock Class-D Amplifier $279.99 $309.00
Rockford Fosgate Prime R2-500X1 500W Prime Series Monoblock Subwoofer Class D Amplifier
Primed for performance, the R2-500X1 amplifier is a 500 watt, class-D, capable of operating at 4Ω or 2Ω mono. This amplifier is extremely efficient because of its class D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allows you to tune the bass for the desired level for the music.
General Features:
Rockford Fosgate Prime R2-500X1
RMS Power Rating:
4 ohms: 300 watts x 1 chan.
2 ohms: 500 watts x 1 chan.
Total power output: 500 watts
Balanced Differential Inputs with RCA Pass Through Outputs
High-Level Input Capable
Defeat able Auto Turn-On Circuit
Features C.L.E.A.N. Set-up
Variable Input Gain adjustment level
R.L.C. Remote Level Control
Variable Infrasonic Filter
Continuously Variable On Board Punch EQ
Top Mounted Control Panel
Short Circuit & Over Current Protection
CEA-2006 Compliant & CE Compliant
Full Range Class D
Rollback Protection
Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers
Input sensitivity:
Low-Level: 150 mV - 4 V
High-Level: 450 mV - 12 V
Frequency Response: 20 Hz - 250 Hz
Total Harmonic Distortion (THD): >1%
Crossover Controls
Low-Pass: 50 Hz - 250 Hz
Sub Infrasonic: 15 Hz - 40 Hz
Recommended Fuse Rating: 80A
4 gauge power and ground wiring is recommended for installation
Dimensions: "1.9" x "6.8" x "8.5"
Authorized Internet Dealer
1 Year Manufacturer's Warranty
What is in the R2-500X1 package:
Rockford Fosgate R2-500X1 owner's manual
Mono subwoofer amplifier
Wired Remote Level Control module
16' Remote cable (RJ-25 connector on both ends)
One 7" Speaker input harnesses
3mm Allen Hex key
Four 3/4" Screws
Two 1/2" Screws
5 Flat washers
1 Nut
Installation and Operation Instructions
Certificate of Performance
Rockford Fosgate contact information
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca


00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Cerwin Vega CVP2000.1D
Monoblock 1000 Watts Class-D Amplifier 1000W RMS $169.99 $199.99
Monoblock 1000 Watts Class-D Amplifier 1000W RMS $169.99 $199.99
Cerwin Vega CVP2000.1D Monoblock 1000 Watts Class-D Amplifier 1-Ohm Amplifier
The Cerwin-Vega Mobile Performance Series of products makes owning a Cerwin-Vega Mobile sound system very affordable for those that are budget-conscious. And with this 2,000 Watt Max Monoblock Class D Amp, you can enjoy the LOUD sound experience at the right price and with the right power! Cerwin-Vega Mobile amplifiers are powerful enough to drive even the most inefficient speakers and bring out their full performance capabilities to dramatic levels of clean, distortion-free sound. All Cerwin-Vega Mobile amplifiers are tested and validated by an outside third-party audio lab that measures and analyzes audio electronics to ensure precise power measurements and follows standards and practices set forth by CTA (Consumer Technology Association).
General Features:
CVP Series 2-Channel Amplifier
RMS Power Output:
1000W × 1 @ 2Ω
700W x 1 @ 4Ω
RMS Power @ 4 ohms: 700 watts x 1 channels
RMS Power @ 2 ohms: 1000 watts x 1 channels
Peak Power @ 4 ohms: 1400 watts x 1 channels
Peak Power @ 2 ohms: 2000 watts x 1 channels
Amplifier Series: CVP (Cerwin-Vega)
Amplifier Class: D
Number of Channels: 1 - Mono
2-Ohm Stable Class D Monoblock Operation
Direct Short, Thermal, & Overload Circuits Protect Amplifier
200mV-6V High Level or Low-Level RCA Input
12dB Bass Boost Increases Low Octave Harmonics
Dimensions: 14.17"W x 9.05"L x 2.09"H
Authorized Internet Dealer
1-year Manufacturer's Warranty
Includes official LAB vinyl sticker (2.13" x 2.75")
⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov


00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate R2-250X1 Monoblock Amplifier
$229.99
$249.99
Rockford Fosgate R2-250X1 Prime Series mono subwoofer amplifier 250-Watt Monoblock Amplifier
Rockford Fosgate's R2 amplifiers are the building blocks for great audio systems, powerful enough even to DRIVE our Punch speakers and subwoofers. They have undergone an amazing upgrade by packing them with the latest features at incredible value. Best of all, they are designed and engineered here in Tempe, Arizona.
Primed for performance, the R2-250X1 is a 250-watt, class-D amplifier capable of operating at 4Ω or 2Ω mono. This amplifier is extremely efficient because of its class-D technology, which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. Perfect for subwoofers, a variable infrasonic filter, and remote level control allows you to tune the bass for the desired level of the music.
General Features:
Rockford Fosgate Prime R2-250X1
Class-D Full-Range Monoblock Amplifier
320 watts x 1 channel @ 4 Ohms RMS Power
600 watts x 2 channel @ 2 Ohms RMS Power
Total power output: 250 watts
Balanced Differential Inputs with RCA Pass Through Outputs
High-Level Input Capable
Defeat able Auto Turn-On Circuit
Features C.L.E.A.N. Set-up
Variable Input Gain adjustment level
R.L.C. Remote Level Control
Variable Infrasonic Filter
Continuously Variable On Board Punch EQ
Top Mounted Control Panel
Short Circuit & Over Current Protection
CEA-2006 Compliant & CE Compliant
Full-Range, Class D
Rollback Protection
Input Sensitivity:
Low-Level: 150 mV - 4 V
High-Level: 450 mV - 12 V
Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers
Frequency Response: 20 Hz - 250 Hz
Total Harmonic Distortion (THD): >1%
Crossover Controls:
Low-Pass: 50 Hz - 250 Hz
Sub Infrasonic: 15 Hz - 40 Hz
Recommended Fuse Rating: 50A
Dimensions: "1.9" x "6.8" x "8.1"
Authorized Internet Dealer
1-year Manufacturer's Warranty
What is in the R2S-1X12 package:
R2S-1X12 owner's manual
Sealed enclosure loaded with one 12" woofer
2 Mounting brackets
Four 3/4" Self-tapping screws
Installation and operation instructions

00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
AudioControl LC-1.1500 amplifier, ACR-1 Dash Remote
$899.00
$1,200.00
AudioControl LC-1.1500 amplifier, ACR-1 Dash Remote
This bundle includes an AudioControl LC-1.1500 High-Power Subwoofer Amplifier with Accubass and ACR-1 Dash Remote.
AudioControl LC-1.1500 Mono Subwoofer AmplifierGeneral Features:
mono subwoofer amplifier
850 watts RMS x 1 at 4 ohms (1,500 watts RMS x 1 at 2 ohms)
Class D amp technology
AccuBASS circuitry for improved bass response
MILC (Maximum Input Level Control) LED optimization and clip indicators
variable low-pass filter (30-230 Hz, 24 dB/octave)
fixed subsonic filter: 24 Hz
preamp and speaker-level inputs
GTO (Great Turn-On) signal-sensing turn-on with speaker-level input
optional wired remote level controller available
fuse rating: 40A x 4
wiring and hardware not included with amplifier
AudioControl Remote ACR-1 Dash Mount Wired Remote Level Control for Select AudioControl Sound Processors
General Features
Wired Remote Level Control
Mounts on the dash using built-in bracket
Detachable mounting plate
Works with select AudioControl sound processors
Direct replacement remote for the Epicenter
Includes 20' power cable
Authorized Dealer
5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer)
What is in the ACR-1 package:
Remote dash mount control
20' RJ-14 cable. Mounting Instructions on packaging
ACR-1 owner's manual
⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov


00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate Prime R2-1200X1 mono amplifier
1200W RMS x 1 at 1 ohm monoblock subwoofer amplifier $409.99 $449.99
1200W RMS x 1 at 1 ohm monoblock subwoofer amplifier $409.99 $449.99
Rockford Fosgate Prime R2-1200X1 mono amplifier 1200W RMS x 1 at 1-ohm monoblock subwoofer amplifier
Primed for performance, the R2-1200X1 is a 1200-watt, class-D amplifier capable of operating at 4Ω, 2Ω, or 1Ω mono. This amplifier is highly efficient because of its class-D technology, which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allow you to tune the bass for the desired level of the music.
General Features:
Rockford Fosgate Prime R2-1200X1
Class-D Full Range Monoblock Amplifier
RMS Power Rating:
4 ohms: 400 watts x 1 chan.
2 ohms: 800 watts x 1 chan.
1 ohm: 1200 watts x 1 chan.
Balanced Differential Inputs with RCA Pass Through Outputs
High-Level Input Capable
Defeatable Auto Turn on Circuit
Features C.L.E.A.N. Set-up
Variable Input Gain adjustment level
R.L.C. Remote Level Control
Variable Infrasonic Filter
Continuously Variable On-Board Punch EQ
Top Mounted Control Panel
Short Circuit & Over Current Protection
CEA-2006 Compliant & CE Compliant
Full Range Class D
Rollback Protection
Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers
Input sensitivity:
Low-Level: 150 mV - 4 V
High-Level: 450 mV - 12 V
Frequency Response: 20 Hz - 250 Hz
Total Harmonic Distortion (THD): >1%
Low-Pass: 50 Hz - 250 Hz @ 12dB
Sub Infrasonic: 15 Hz - 40 Hz
Fuse Rating: 120A
4-gauge power and ground wiring are recommended for installation.
Dimensions: 1.9" x 6.8" x 11.3"
Authorized Internet Dealer
1-year Manufacturer's Warranty
What is in the R2-1200X1 package:
Mono subwoofer amplifier
Wired Remote Level Control module
16' Remote cable (RJ-25 connector on both ends)
One 7" Speaker input harness
3mm Allen Hex key
Four 3/4" Screws
Two 1/2" Screws
5 Flat washers
1 Nut
Installation and Operation Instructions
Certificate of Performance
R2-1200X1 owner’s manual
Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.


00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Alpine KTA-30MW Car Amplifier Mono 600W Weather Resistant Tough Power Pack Amp
$499.95
$700.95
Alpine KTA-30MW Car Amplifier Mono 300-Watt RMS Weather-Resistant Tough Power Pack Amplifier
A TOUGH MINI AMP THAT PACKS A PUNCH
Get big amp performance in a compact, resilient package. With Alpine’s exclusive technology, Dynamic Peak Power (D.P.P.), the KTA-30MW Weather-Resistant Tough Power Pack is sure to deliver powerful bass output for subwoofers used in those open cab vehicles and toys. This small and efficient amplifier can be installed with an aftermarket or factory head unit while adding up to 600 watts of D.P.P. power. Its weather resistance makes the KTA-30MW a good choice for use in exposed installations like side-by-sides, boats, open-top vehicles, and motorcycle saddlebags.
A SOUND SYSTEM BOOST WITHOUT THE BIG SPACE COMMITMENT
The KTA-30MW is perfect for when you want to add subwoofer power but don’t have space for a large amplifier. It is compatible with an aftermarket or factory head unit and provides up to 600 DPP watts to the subwoofer of your choice.
HALF THE SIZE OF OUR SMALLEST TRADITIONAL AMPLIFIERS
The KTA-30MW measures just 9-3/16” (W) x 1-5/8” (H) x 3-3/4” (D), so its small footprint lets it fit where most amplifiers won’t, like under the dash or in the glove compartment, installed under the dash of a side-by-side, placed in the saddlebag of a motorcycle, or used in other places where space is an issue.
General Features:
Alpine KTA-30MW
Class D Monoblock Weather-Resistant Power Pack Amplifier
300 Watts RMS X 1 @ 4 Ohms Power Handling
600 Watts RMS X 1 @ 2 Ohms Power Handling
CTA-2006 compliant
Frequency Response: 20-400 Hz
Total Harmonic Distortion (THD): <1%
Signal to Noise Ratio: 83dB
Variable Low Pass filter 50-400Hz @ -24dB/Oct.
Variable Bass Boost (0-12 dB at 50 Hz)
Fuse Rating: 25A
Weather-resistant (IP66 rating)
Dynamic Peak Power (D.P.P.) technology intelligently adjusts the gain to adapt to musical needs automatically
Dimensions: 7” W x 3.5” H x 1.25” D
Authorized Dealer
1-year Manufacturer's Warranty
What is in the KTA-30MW box:
Mono amplifier
14" Power/signal harness (26-pin connector on one end and bare wires + RCAs on the other ends)
4 Self-tapping screws (Length 3/4")
Connection sheet
Limited Warranty sheet
KTA-30MW owner's manual
Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.


00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Alpine R-A75M Car Amplifier
R-Series Class D Monoblock Subwoofer Amplifier 750 Watts RMS $549.99 $799.99
R-Series Class D Monoblock Subwoofer Amplifier 750 Watts RMS $549.99 $799.99
Alpine R-A75M R-Series Class D Monoblock Subwoofer Amplifier 750 Watts RMS
HI-RESOLUTION AUDIO COMPLIANT
The R-Series amplifiers utilize Alpine’s advanced amplifier platform that takes the classic Class-D amplifier circuit and adds dual post-filter feedback loops for unmatched accuracy and control. This technology., originally launched in the premium X-Series amplifiers, produces efficient power with enhanced dynamic range, qualifying the R-Series amplifiers to be Hi-Resolution Audio compliant.
THE LOUDEST FAMILY ON THE BLOCK
The “R” line of speakers and subwoofers have a heritage of sound quality you can hear from a block away, and the newly added R-Series amplifiers are no exception. Aside from their best-in-class performance, these amplifiers are tuned to emphasize the characteristics of the R-Series speakers and subwoofers, giving you that legendary R-Series experience.
General Features:
R-Series Class D Monoblock Subwoofer Amplifier
Power Output:
500 watts RMS x 1 @ 4 ohms
750 watts RMS x 1 @ 2 ohms
CTA-2006 compliant
Variable low-pass filter (50-400 Hz, 24 dB/octave)
Variable bass boost (0-12 dB at 50 Hz)
Variable subsonic filter (min-40 Hz, 24 dB/octave)
We recommend the Alpine RUX-KNOB.2 if you are looking for a remote bass knob for Alpine Amplifiers
Preamp and speaker-level inputs
Speaker wire to RCA adapter required for speaker-level input - we recommend the Rockford Fosgate RFI2SW
preamp outputs
wiring and hardware not included with amplifier
4-gauge power and ground leads recommended - get the NVX XAPK4 for this
Fuse rating: 40A x 2
Dimensions: 9" W x 2-1/16" H x 7-1/8" D
Authorized Dealer
1-year Manufacturer's Warranty
What's in the R-A75M package:
Mono subwoofer amplifier
Two 40-amp ATO fuses
4 Mounting feet
Four 3/4" Screws
Eight M2.5x5.5mm Machine screws
2mm Allen wrench
3mm Allen wrench
Owner's manual
Alpine Verification Certificate
Warranty information
Power supply note
Online product registration information
Alpine R-A75M owner's manual
Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.


00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate Prime R2-250X1 Mono Subwoofer Amplifier
$229.99
$249.99
Rockford Fosgate R2-250X1 Prime Series mono subwoofer amplifier 250-Watt Monoblock Amplifier
Rockford Fosgate's R2 amplifiers are the building blocks for great audio systems, powerful enough even to DRIVE our Punch speakers and subwoofers. They have undergone an amazing upgrade by packing them with the latest features at incredible value. Best of all, they are designed and engineered here in Tempe, Arizona.
Primed for performance, the R2-250X1 is a 250-watt, class-D amplifier capable of operating at 4Ω or 2Ω mono. This amplifier is extremely efficient because of its class-D technology, which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. Perfect for subwoofers, a variable infrasonic filter, and remote level control allows you to tune the bass for the desired level of the music.
General Features:
Rockford Fosgate Prime R2-250X1
Class-D Full-Range Monoblock Amplifier
320 watts x 1 channel @ 4 Ohms RMS Power
600 watts x 2 channel @ 2 Ohms RMS Power
Total power output: 250 watts
Balanced Differential Inputs with RCA Pass Through Outputs
High-Level Input Capable
Defeat able Auto Turn-On Circuit
Features C.L.E.A.N. Set-up
Variable Input Gain adjustment level
R.L.C. Remote Level Control
Variable Infrasonic Filter
Continuously Variable On Board Punch EQ
Top Mounted Control Panel
Short Circuit & Over Current Protection
CEA-2006 Compliant & CE Compliant
Full-Range, Class D
Rollback Protection
Input Sensitivity:
Low-Level: 150 mV - 4 V
High-Level: 450 mV - 12 V
Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers
Frequency Response: 20 Hz - 250 Hz
Total Harmonic Distortion (THD): >1%
Crossover Controls:
Low-Pass: 50 Hz - 250 Hz
Sub Infrasonic: 15 Hz - 40 Hz
Recommended Fuse Rating: 50A
Dimensions: "1.9" x "6.8" x "8.1"
Authorized Internet Dealer
1-year Manufacturer's Warranty
What is in the R2S-1X12 package:
R2S-1X12 owner's manual
Sealed enclosure loaded with one 12" woofer
2 Mounting brackets
Four 3/4" Self-tapping screws
Installation and operation instructions
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca

00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate M2-500X1 Monoblock Marine Amplifier with Absolute KIT4 4 Gauge Amp Kit
$349.99
$699.98
Rockford Fosgate M2-500X1 Monoblock Marine Amplifier with Absolute KIT4 4 Gauge Amp Kit
Rockford Fosgate M2-500X1 500 Watt Monoblock marine amplifierDesigned to withstand the elements, the M2-500X1 Element Ready™ amplifier is a 500 watt, class-D model, capable of operating at 4Ω or 2Ω mono. This amplifier is extremely efficient because of its class D technology which reduces demand on the electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allow you to tune the bass for the desired level for the music.
General Features:
Element Ready™ design protects against outdoor exposure
Conformal coated circuit board protects against dust and water
UV stable powder-coated cast aluminum heatsink
Zinc Nickel-plated Marine grade brass connection terminals
C.L.E.A.N. input/output clip detection and indicator LEDs
MEHSA 4 (Maximum Efficiency Heat Sink Application)
NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances.
Optimized using AudioGraph PowerCube measurement tool
Continuously Variable On Board Punch EQ
Includes RLC Remote Level Control
Focused mass heatsink design
Top Mounted Control Panel
Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers
Short Circuit & Over Current Protection
Variable Infrasonic Filter
Integrated Power and Speaker Terminals
Balanced Differential Inputs via Speaker Line or RCA Inputs
RCA pass-thru outputs
Integration with OEM and Aftermarket Radios
"Auto-Sense" turn-on with remote out (high level in)
Auto-Sense bypass switch for vehicles with RAP (Retained Accessory Power)
Low Impedance Stability
Proprietary testing using RATS (Rockford Automated Testing System)
CEA-2006 Compliant & CE Compliant
Rollback Protection
Power Ratings: 300 Watts x 1 @ 4 ohms
Power Ratings: 500 Watts x 1 @ 2 ohms
Dynamic Power Ratings: 350 Watts x 1 @ 4 ohms
Dynamic Power Ratings: 590 Watts x 1 @ 2 ohms
Frequency Response: 20 Hz - 250 Hz
Low-Level Input Sensitivity: 150 mV - 4 V
High-Level Input Sensitivity: 450 mV - 12 V
Total Harmonic Distortion (THD+Noise): <1.0%
Low-Level Signal Input: 2 RCA
High-Level Input Signal: 4-Pin Molex
Low-Level Signal Output: 2 RCA (Pass-Thru active with RCA or Hi-Level input)
Tone-Controls: 0 to +18 dB @ 45 Hz
Low-Pass Crossover Controls: 50 Hz - 250 Hz @ 12dB/Octave Butterworth
Infrasonic Crossover Controls: 15 Hz - 40 Hz @ 12dB/Octave Butterworth
4 gauge power and ground wiring is recommended for installation. Contact us for information regarding a discount on select amplifier kits from our website when purchased together with this amplifier.
Dimensions: 1.9"W x 6.8"D x 8.5"H
Authorized Internet Dealer
1-year Manufacturer's Warranty
⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca

00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate M2-500X1 Monoblock Marine Amplifier
$349.99
$599.98
Rockford Fosgate M2-500X1 Monoblock Marine Amplifier
Rockford Fosgate M2-500X1 500 Watt Monoblock marine amplifierDesigned to withstand the elements, the M2-500X1 Element Ready™ amplifier is a 500 watt, class-D model, capable of operating at 4Ω or 2Ω mono. This amplifier is extremely efficient because of its class D technology which reduces demand on the electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allow you to tune the bass for the desired level for the music.
General Features:
Element Ready™ design protects against outdoor exposure
Conformal coated circuit board protects against dust and water
UV stable powder-coated cast aluminum heatsink
Zinc Nickel-plated Marine grade brass connection terminals
C.L.E.A.N. input/output clip detection and indicator LEDs
MEHSA 4 (Maximum Efficiency Heat Sink Application)
NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances.
Optimized using AudioGraph PowerCube measurement tool
Continuously Variable On Board Punch EQ
Includes RLC Remote Level Control
Focused mass heatsink design
Top Mounted Control Panel
Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers
Short Circuit & Over Current Protection
Variable Infrasonic Filter
Integrated Power and Speaker Terminals
Balanced Differential Inputs via Speaker Line or RCA Inputs
RCA pass-thru outputs
Integration with OEM and Aftermarket Radios
"Auto-Sense" turn-on with remote out (high level in)
Auto-Sense bypass switch for vehicles with RAP (Retained Accessory Power)
Low Impedance Stability
Proprietary testing using RATS (Rockford Automated Testing System)
CEA-2006 Compliant & CE Compliant
Rollback Protection
Power Ratings: 300 Watts x 1 @ 4 ohms
Power Ratings: 500 Watts x 1 @ 2 ohms
Dynamic Power Ratings: 350 Watts x 1 @ 4 ohms
Dynamic Power Ratings: 590 Watts x 1 @ 2 ohms
Frequency Response: 20 Hz - 250 Hz
Low-Level Input Sensitivity: 150 mV - 4 V
High-Level Input Sensitivity: 450 mV - 12 V
Total Harmonic Distortion (THD+Noise): <1.0%
Low-Level Signal Input: 2 RCA
High-Level Input Signal: 4-Pin Molex
Low-Level Signal Output: 2 RCA (Pass-Thru active with RCA or Hi-Level input)
Tone-Controls: 0 to +18 dB @ 45 Hz
Low-Pass Crossover Controls: 50 Hz - 250 Hz @ 12dB/Octave Butterworth
Infrasonic Crossover Controls: 15 Hz - 40 Hz @ 12dB/Octave Butterworth
Dimensions: 1.9"W x 6.8"D x 8.5"H
Authorized Internet Dealer
1-year Manufacturer's Warranty
⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca