Monoblock Amplifiers (181)

Rockford Fosgate T2500-1bdCP Power Series mono sub amplifier 2,500 Watts RMS x 1 at 2 ohms The T2500-1bdCP is based on the legendary T2500-1bd amplifier design with a proprietary "Constant Power" configuration that delivers up to 25% more power (Watts) across all impedance loads. The result is a listening experience cleaner, louder and more impressive than ever before. This T2500-1bdCP amplifier pumps out 2,500 watts, easily driving any array of woofers wired to a 1-ohm load. Use two amps in Power-Sync mode for a whopping 5,000 watt power horse! Product highlights: mono subwoofer amplifier 1,500 watts RMS x 1 at 4 ohms (2,500 watts RMS x 1 at 2 ohms) 2,500 watts RMS x 1 at 1 ohm CEA-2006 compliant Dynamic Thermal Management cooling system Master Sync: allows two of these amps to be tied together variable low-pass filter (32-250 Hz, 24 dB/octave) selectable subsonic filter (28Hz, 12 dB/octave) variable bass boost (0-18 dB at 45 Hz) optional wired remote bass boost Class-BD amplifier design MOSFET power and output stages preamp inputs and outputs 1/0-gauge power and ground leads and an 250-amp fuse recommended — wiring and hardware not included with amplifier no onboard fuses — when installing multiple amps in a system, an additional 250-amp in-line fuse between the distribution block and the amplifier is recommended 21-7/8"W x 2-3/16"H x 9-7/16"D Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Punch P500X1bd Mono subwoofer amplifier 500 watts RMS x 1 at 1 ohm Big power for your sub or subsystem Rockford Fosgate's Punch P500X1bd subwoofer amp can produce up to 500 watts RMS, giving you plenty of clean power for your rhythm track. And the P500X1bd can drive a 1-ohm load, so you can power multiple subs without any trouble. A low-pass filter keeps the high notes away from your sub, while a subsonic filter helps you rein in runaway boom. The Punch bass boost lets you add some of that boom back into the mix when it's needed. Easy to set for optimum performance Once again, Rockford Fosgate steps away from the crowd with their C.L.E.A.N. technology (Calibrated Level Eliminates Audible Noise) — a setup system that ensures your music will sound as clean and powerful as possible. It works like this: first, download the setup tones from Rockford Fosgate, then play the tone, adjust the receiver volume until a red clip light on the amp goes out, then turn the amp gain up until a blue light comes on. It's that simple — your amplifier will be perfectly set to match your receiver's output. When your receiver reaches maximum clean volume, you'll get maximum clean power from your power amp. At quiet listening levels, you'll hear less background noise and more of your music. Keeps an eye on things while playingIf that blue light turns solid red while you're playing music, the amp's telling you that your source is distorting and you should turn it down, or risk damage to your gear. The optional PLC2 remote level control also doubles as a clip indicator, so you can see from the front seat if your music's clipping. The amp's built-in computer keeps tabs on the output current, ensuring that plunging speaker impedances (they change during play) or even a short circuit won't hurt anything. Maintaining coolness raises efficiency and lowers distortionRockford Fosgate's Dynamic Thermal Management system uses forced air to dissipate heat evenly across the amp and out through the high-mass heatsink, efficiently drawing heat away from vital internal parts. Their proprietary MEHSA cooling process maximizes the heat transfer from the MOSFET devices to the heatsink, allowing the heat to escape more readily, so the transistors stay cooler and work better. Product highlights: mono subwoofer amplifier 150 watts RMS x 1 at 4 ohms (300 watts RMS x 1 at 2 ohms) 500 watts RMS x 1 at 1 ohm CEA-2006 compliant Features: variable low-pass filter filter (50-250 Hz, 12 dB/octave) selectable subsonic filter (28Hz, 12 dB/octave) variable PEQ2 bass boost (0-18 dB at 45 Hz) C.L.E.A.N. gain setup system includes clip lights and link to Rockford Fosgate's setup tones Class-BD amplifier design frequency response: 20-250 Hz Dynamic Thermal Management and MEHSA MOSFET cooling systems MOSFET power and output stages preamp inputs and outputs speaker-level inputs (speaker wire to RCA adapter required) signal-sensing turn-on with speaker-level inputs eliminate the need for remote turn-on lead More Info: optional PLC2 wired remote level control with clip light available 4-gauge power and ground leads and an 80-amp fuse recommended — wiring and hardware not included with amplifier no onboard fuses — when installing multiple amps in a system, an additional 80-amp in-line fuse between the distribution block and the amplifier is recommended 11-1/8"W x 2-7/16"H x 8-13/16"D warranty: 1 year What is in the P500X1bd box: Mono subwoofer amplifier Four 1-1/2" Self-tapping screws 2.5mm Allen wrench Quick setup instructions Certificate of Performance P500X1bd owner's manual ⚠️Warning: Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Rockford Fosgate Punch P1000X1bd Mono subwoofer amplifier 1,000 watts RMS x 1 at 1 ohm The Punch P1000X1bd mono amplifier pumps out 1,000 Watts into a 1-Ohm load. The Class-BD technology produces bass more efficiently over traditional amps, and its frequency response is optimized for subwoofers. With its super-efficient Class-BD circuit topology, the P1000X1bd assures maximum BOOM for your buck! Due to its dedicated low-frequency response, this amplifier is optimized for mid-bass speakers or subwoofers only. No need to worry because its 1-ohm capability will easily drive a pair of 4-ohm DVC subwoofers or quad-configuration of 2-ohm DVC subwoofers. General Features: Punch BD Series Monoblock Class BD Car Amplifier RMS Power Rating: 4 ohms: 300 watts x 1 channel 2 ohms: 500 watts x 1 channel 1 ohm: 1000 watts x 1 channel CEA-2006 compliant amplifier Features C.L.E.A.N. Set-up with the 10-step set-up procedure w/ input/output clip detection and indicator LEDs MOSFET power supply Muted turn on Cast aluminum heatsink 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protection indicators Nickel-plated captive C-clamp terminals Ultra-efficient Class BD circuitry to maximize amplifier power efficiency On-board differential inputs eliminate noise picked up by the signal cable Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately) MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowering the operating temperature and potential for noise - similar to circuit boards designed by aerospace manufacturers Input sensitivity: 150mV - 12V On-board Punch EQ with +18dB boost @ 45Hz. Variable low-pass filter: 50-250 Hz Selectable infrasonic filter: off / 28 Hz Frequency response: 20 - 250 Hz Total Harmonic Distortion: <1.0% Dimensions: 13-5/16"L x 7-3/4"W x 2-3/8"H 8 AWG to 18 AWG speaker wire output terminals 4 gauge power and ground wiring is recommended for installation. Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the P1000X1bd package: P1000X1bd owner's manual Mono subwoofer amplifier Four 1-1/2" Self-tapping screws 5mm Allen wrench Quick setup instructions ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Punch P500X1BD 500W RMS Punch Series Monoblock Class D Car Power Amplifier The Punch P500X1bd is a mono amplifier capable of 500 Watts into a 1-Ohm load. The Class-BD technology produces bass more efficiently over traditional amps, and its frequency response allows it to be optimized for subwoofers. General Features Punch BD Series Monoblock Class BD Car Amplifier RMS Power Rating: 4 ohms: 150 watts x 1 chan. 2 ohms: 300 watts x 1 chan. 1 ohm: 500 watts x 1 chan. CEA-2006 compliant amplifier MOSFET power supply Muted turn-on. Cast aluminum heatsink. 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protect indicators. Nickel-plated captive C-clamp terminals. Ultra-efficient Class BD circuitry to maximize amplifier power efficiency. On-board differential inputs eliminate noise picked up by the signal cable. Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately) MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span. Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances. Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low. DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowers the operating temperature and potential for noise-like circuit boards designed by aerospace manufacturers. Input sensitivity: 150mV - 12V On-board Punch EQ with +18dB boost @ 45Hz. Variable low-pass filter: 50-250 Hz Selectable infrasonic filter: off / 28 Hz Frequency response: 20 - 250 Hz Total Harmonic Distortion: <1.0% Dimensions: 11"L x 7-3/4"W x 2-3/8"H 8 AWG to 18 AWG speaker wire output terminals Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the P500X1bd box: Mono subwoofer amplifier Four 1-1/2" Self-tapping screws 2.5mm Allen wrench Quick setup instructions Certificate of Performance P500X1bd owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca

Cerwin-Vega CVPRO3K 3000W Full Range Class D Monoblock Amp Subwoofer Amplifier Latest High-Efficiency Class D Topology. Full Range Class D Monoblock Amplifier. Compact Size with Ambient backlit logo. RCA “Pass Thru” output for easy system expansion. Fully Variable Crossovers (12dB per octave). 3000WX1@1Ω. 2050WX1@2Ω. 1100WX1@4Ω. 15-20KHz Frequency Response. LPF Filter 80-20KHz. 12dB Crossover Slope. General Features: CVP Pro Monoblock Class D Car Amplifier RMS Power Rating: 4 ohms: 1100 watts x 1 chan. 2 ohms: 2050 watts x 1 chan. 1 ohm: 3000 watts x 1 chan. Wired remote bass level control included Variable Bass Boost 0 to +12 dB bass boost at 50 Hz Mono channel operation Speaker-level (high-level) inputs with signal sensing for automatic turn-on Dimensions: 8.85"W 7.95 "L 2.61"H Authorized Internet Dealer 1-year Manufacturer's Warranty Specification: Amplifier Monoblock MAX Power Rating 6000 W MAX RMS Power (1Ω) 3000 RMS Power(2Ω) 2050 RMS Power (4Ω) 1100 Topology Full-Range Class D Frequency Response 15-20KHz Power Supply Full PWM Power Supply (Threshold) 10.0VDC– 17.0VDC Idle Current (2.6A) Distortion - THD (1KHz@4Ω) 0.1% Distortion - S/N Ratio (A weight @ 1W) -90dBA Distortion - S/N Ratio (A weight @ FP) -105dBA Input Sensitivity 0.2V – 5.0V Input Impedance - Low Input Level 20 KΩ Output Impedance 0.0297 Ω Damping Factor (50Hz@4Ω) >150 Bandwidth (-3dB) 15Hz-20KHz LPF Filter 80-20KHz Crossover (-12 dB/ Oct) Variable High-Pass 50Hz-20KHz Crossover (-12 dB/ Oct) Variable Low-Pass 15Hz-1KHz Crossover (-12 dB/ Oct) Variable Sub-Sonic 15Hz-1KHz FUSE Ratings - ATC 150A Dimension - Length x Width x Height - Inches(mm) 7.95” x 8.85” x 2.61” ( 202 x 225 x 66.5mm ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine KTA-30MW Car Amplifier Mono 300-Watt RMS Weather Resistant Tough Power Pack Amplifier A TOUGH MINI AMP THAT PACKS A PUNCH Get big amp performance in a compact, resilient package. With Alpine’s exclusive technology, Dynamic Peak Power (D.P.P.), the KTA-30MW Weather Resistant Tough Power Pack is sure to deliver powerful bass output for subwoofers used in those open cab vehicles and toys. This small and efficient amplifier can be installed with an aftermarket or factory head unit while adding up to 600 watts of D.P.P. power. Its weather resistance makes the KTA-30MW a good choice for use in exposed installations like side-by-sides, boats, open-top vehicles, and motorcycle saddlebags. A SOUND SYSTEM BOOST WITHOUT THE BIG SPACE COMMITMENT The KTA-30MW is perfect for when you want to add subwoofer power but don’t have space for a large amplifier. It is compatible with an aftermarket or factory head unit and provides up to 600 DPP watts to the subwoofer of your choice. HALF THE SIZE OF OUR SMALLEST TRADITIONAL AMPLIFIERS The KTA-30MW measures just 9-3/16” (W) x 1-5/8” (H) x 3-3/4” (D), so its small footprint lets it fit where most amplifiers won’t, like under the dash or in the glove compartment, installed under the dash of a side-by-side, placed in the saddlebag of a motorcycle, or used in other places where space is an issue. General Features: Alpine KTA-30MW Class D Monoblock Weather Resistant Power Pack Amplifier 300 Watts RMS X 1 @ 4 Ohms Power Handling 600 Watts RMS X 1 @ 2 Ohms Power Handling CTA-2006 compliant Frequency Response: 20-400 Hz Total Harmonic Distortion (THD): <1% Signal to Noise Ratio: 83dB Variable Low Pass filter 50-400Hz @ -24dB/Oct. Variable Bass Boost (0-12 dB at 50 Hz) Fuse Rating: 25A Weather-resistant (IP66 rating) Dynamic Peak Power (D.P.P.) technology intelligently adjusts the gain to automatically adapt to musical needs Dimensions: 7” W x 3.5” H x 1.25” D Authorized Dealer 1-year Manufacturer's Warranty What is in the box: Mono amplifier 14" Power/signal harness (26-pin connector on one end and bare wires + RCAs on other ends) 4 Self-tapping screws (Length 3/4") Connection sheet Limited Warranty sheet Alpine KTA-30MW owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Rockford Fosgate Prime R2-750X1 750W RMS Prime Series Class-D Monoblock 1-Ohm Stable AmplifierLooking for a monoblock with reliable power ratings and efficiency without spending a fortune? Rockford Fosgate's R2-750X1. With a rating of 250 watts x 1 channel @ 4 ohms, 500 watts x 1 channel @ 2 ohms, and 750 watts x 1 channel at 1 ohm, this amplifier is perfect for those looking to amplify anything from entry-level to some more serious power at the 1-ohm rating. Fine-tuning your amplifier will be a cinch using the variable high-pass, infrasonic, and variable bass boost crossovers. A cast aluminum heat sink will control heat dissipation to keep your amplifier running cool and efficiently no matter how long or short your listening sessions are. So if you are looking for a Class D highly efficient monoblock amplifier that will never let you down, look no further than Rockford Fosgate's R2-750X1. General Features: Rockford Fosgate Prime R2-750X1 Class-D FullRange MonoBlock Amplifier RMS Power Rating: 4 ohms: 250 watts x 1 channel RMS Power Rating: 2 ohms: 500 watts x 1 channel RMS Power Rating: 1 ohm: 750 watts x 1 channel Total power output: 500 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeatable Auto Turn-On Circuit Features C.L.E.A.N. Set-up Variable Input Gain adjustment level R.L.C. Remote Level Control Variable Infrasonic Filter Continuously Variable On Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Full Range Class D Rollback Protection Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers Input sensitivity: Low-Level: 150 mV - 4 V High-Level: 450 mV - 12 V Frequency Response: 20 Hz - 250 Hz Total Harmonic Distortion (THD): >1% Crossover Controls Low-Pass: 50 Hz - 250 Hz Sub Infrasonic: 15 Hz - 40 Hz Recommended Fuse Rating: 120A 4 gauge power and ground wiring is recommended for installation Dimensions: "1.9" x "6.8" x "10.1" Authorized Internet Dealer 1-Year Manufacturer's Warranty ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.