
00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate Prime R500X1D 1-Channel Car Prime 500 Watt RMS Class D Car Mono Amplifier
$279.99
$329.99
Rockford Fosgate Prime R500X1D 1-Channel Car Prime 500 Watt RMS Class D Car Mono Amplifier
The Prime R500X1D is a 500-watt mono amplifier using efficient Class-D circuit topology. This amplifier is capable of running a 2-Ohm load and includes onboard Punch Bass and remote Punch Level Control. Are you ready for a dedicated subwoofer amplifier for your car or truck? The Prime R500X1D is the perfect companion for any Car Audio Fanatic getting into mobile audio who wants a two-amplifier system: one amp running mids/highs and the second running subwoofers. This class D mono amplifier features variable Punch Bass, variable crossovers, Pass-Thru jacks to daisy chain another amplifier, and a remote Punch Level Control for mounting under the dash or the center console.
General Features:
Prime Series Class D Monoblock Car Amplifier
RMS Power Rating: 4 ohms: 300 watts x 1 channel
RMS Power Rating: 2 ohms: 500 watts x 1 channel
CEA-2006 compliant amplifier
Efficient Class-D circuit topology
12dB/octave Butterworth crossover
RCA pass-thru outputs
On-board Punch EQ with +18dB boost @ 45Hz.
High-level inputs
Remote PLC (Punch Level Control)
0°/180° Phase Switch
Real-time output and power supply thermal sensing
Cast aluminum heatsink
4 Gauge power/ground connectors
MOSFET power supply
Over-current protection
Short circuit protection
Muted turn on
Frequency Response: 20 - 250 Hz +/- 1 dB
Efficiency: 89% @ 4-ohm
Total Harmonic Distortion: <1.0%
Signal to Noise Ratio: >100 dB
Damping Factor: >200 dB
Input Sensitivity: 150 mV - 4V
Recommended Fuse: 50A x 1 (not included)
8-gauge speaker wire terminals
Dimensions: 8.50"L x 6.80"W x 2.00"H
Authorized Internet Dealer
1-year Manufacturer's Warranty
What is in the box:
Rockford Fosgate R500X1D owner's manual
Mono subwoofer amplifier
Remote Punch Level Control module
18' Remote Punch Level Control cable (RJ-25 connector on both ends)
6" Speaker level input harness
3mm Allen wrench
Four 3/4" Self-tapping screws
Two 1/2" Self-tapping screws
4 Flat washers
Installation & Operation manual (English/ French/ Spanish/ German/ Italian)
Amplifier verification certificate
⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate Prime R500X1D 1-Channel Class D Car Mono Amplifier + 4G Amp Kit
$299.99
$329.99
Rockford Fosgate Prime R500X1D 1-Channel Car Prime 500 Watt RMS Class D Car Mono Amplifier + 4G Amp Kit
The Prime R500X1D is a 500-watt mono amplifier using efficient Class-D circuit topology. This amplifier is capable of running a 2-Ohm load and includes onboard Punch Bass and remote Punch Level Control. Are you ready for a dedicated subwoofer amplifier for your car or truck? The Prime R500X1D is the perfect companion for any Car Audio Fanatic getting into mobile audio who wants a two-amplifier system: one amp running mids/highs and the second running subwoofers. This class D mono amplifier features variable Punch Bass, variable crossovers, Pass-Thru jacks to daisy chain another amplifier, and a remote Punch Level Control for mounting under the dash or the center console.
General Features:
Prime Series Class D Monoblock Car Amplifier
RMS Power Rating: 4 ohms: 300 watts x 1 channel
RMS Power Rating: 2 ohms: 500 watts x 1 channel
CEA-2006 compliant amplifier
Efficient Class-D circuit topology
12dB/octave Butterworth crossover
RCA pass-thru outputs
On-board Punch EQ with +18dB boost @ 45Hz.
High-level inputs
Remote PLC (Punch Level Control)
0°/180° Phase Switch
Real-time output and power supply thermal sensing
Cast aluminum heatsink
4 Gauge power/ground connectors
MOSFET power supply
Over-current protection
Short circuit protection
Muted turn on
Frequency Response: 20 - 250 Hz +/- 1 dB
Efficiency: 89% @ 4-ohm
Total Harmonic Distortion: <1.0%
Signal to Noise Ratio: >100 dB
Damping Factor: >200 dB
Input Sensitivity: 150 mV - 4V
Recommended Fuse: 50A x 1 (not included)
8-gauge speaker wire terminals
Dimensions: 8.50"L x 6.80"W x 2.00"H
Authorized Internet Dealer
1-year Manufacturer's Warranty
What is in the box:
Rockford Fosgate R500X1D owner's manual
Mono subwoofer amplifier
Remote Punch Level Control module
18' Remote Punch Level Control cable (RJ-25 connector on both ends)
6" Speaker level input harness
3mm Allen wrench
Four 3/4" Self-tapping screws
Two 1/2" Self-tapping screws
4 Flat washers
Installation & Operation manual (English/ French/ Spanish/ German/ Italian)
Amplifier verification certificate
⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate Prime R500X1D 500 Watt RMS Mono Car Class D Amplifier + 4 Gauge Amplifier Kit
$299.99
$599.99
Rockford Fosgate Prime R500X1D 1-Channel Car Prime 500 Watt RMS Class D Car Mono Amplifier + 4G Amp Kit
The Prime R500X1D is a 500-watt mono amplifier using efficient Class-D circuit topology. This amplifier is capable of running a 2-Ohm load and includes onboard Punch Bass and remote Punch Level Control. Are you ready for a dedicated subwoofer amplifier for your car or truck? The Prime R500X1D is the perfect companion for any Car Audio Fanatic getting into mobile audio who wants a two-amplifier system: one amp running mids/highs and the second running subwoofers. This class D mono amplifier features variable Punch Bass, variable crossovers, Pass-Thru jacks to daisy chain another amplifier, and a remote Punch Level Control for mounting under the dash or the center console.
General Features:
Prime Series Class D Monoblock Car Amplifier
RMS Power Rating: 4 ohms: 300 watts x 1 channel
RMS Power Rating: 2 ohms: 500 watts x 1 channel
CEA-2006 compliant amplifier
Efficient Class-D circuit topology
12dB/octave Butterworth crossover
RCA pass-thru outputs
On-board Punch EQ with +18dB boost @ 45Hz.
High-level inputs
Remote PLC (Punch Level Control)
0°/180° Phase Switch
Real-time output and power supply thermal sensing
Cast aluminum heatsink
4 Gauge power/ground connectors
MOSFET power supply
Over-current protection
Short circuit protection
Muted turn on
Frequency Response: 20 - 250 Hz +/- 1 dB
Efficiency: 89% @ 4-ohm
Total Harmonic Distortion: <1.0%
Signal to Noise Ratio: >100 dB
Damping Factor: >200 dB
Input Sensitivity: 150 mV - 4V
Recommended Fuse: 50A x 1 (not included)
8-gauge speaker wire terminals
Dimensions: 8.50"L x 6.80"W x 2.00"H
Authorized Internet Dealer
1-year Manufacturer's Warranty
What is in the box:
Rockford Fosgate R500X1D owner's manual
Mono subwoofer amplifier
Remote Punch Level Control module
18' Remote Punch Level Control cable (RJ-25 connector on both ends)
6" Speaker level input harness
3mm Allen wrench
Four 3/4" Self-tapping screws
Two 1/2" Self-tapping screws
4 Flat washers
Installation & Operation manual (English/ French/ Spanish/ German/ Italian)
Amplifier verification certificate
⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov


00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate R2-750X1 750-Watt Mono Amplifier
$349.99
$429.99
Rockford Fosgate Prime R2-750X1 750W Prime Series Monoblock Subwoofer Class D Amplifier
Primed for performance, the R2-750X1 amplifier is a 750-watt, Class-D, capable of operating at 4Ω, 2Ω, or 1Ω mono. This amplifier is extremely efficient because of its Class-D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allow you to tune the bass for the desired level of the music.
Rockford Fosgate's R2 amplifiers are the building blocks for great audio systems, powerful enough to even DRIVE our Punch speakers and subwoofers. They have undergone an amazing upgrade by packing them with the latest features at an incredible value. Best of all, they are designed and engineered here in Tempe, Arizona.
General Features:
Rockford Fosgate Prime R2-750X1
RMS Power Rating: 4 ohms: 250 watts x 1 channel
RMS Power Rating: 2 ohms: 500 watts x 1 channel
RMS Power Rating: 1 ohm: 750 watts x 1 channel
Total power output: 500 watts
Balanced Differential Inputs with RCA Pass Through Outputs
High-Level Input Capable
Defeatable Auto Turn on Circuit
Features C.L.E.A.N. Set-up
Variable Input Gain adjustment level
R.L.C. Remote Level Control
Variable Infrasonic Filter
Continuously Variable On-Board Punch EQ
Top Mounted Control Panel
Short Circuit & Over Current Protection
CEA-2006 Compliant & CE Compliant
Full Range Class D
Rollback Protection
Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers
Input sensitivity: Low-Level: 150 mV - 4 V
Input sensitivity: High-Level: 450 mV - 12 V
Frequency Response: 20 Hz - 250 Hz
Total Harmonic Distortion (THD): >1%
Crossover Controls: Low-Pass: 50 Hz - 250 Hz
Crossover Controls: Sub Infrasonic: 15 Hz - 40 Hz
Recommended Fuse Rating: 120A
4-gauge power and ground wiring are recommended for installation.
Dimensions: "1.9" x "6.8" x "10.1"
Authorized Internet Dealer
1-Year Manufacturer's Warranty
What is in the R2-750X1 package:
Mono subwoofer amplifier
Wired Remote Level Control module
16' Remote cable (RJ-25 connector on both ends)
One 7" Speaker input harness
3mm Allen Hex key
Four 3/4" Screws
Two 1/2" Screws
5 Flat washers
1 Nut
Installation and Operation Instructions
Certificate of Performance
Rockford Fosgate contact information
Rockford Fosgate R2-500X1 owner's manual
⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.


00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate R2-750X1 Prime 750 Watt 1ohm Mono punch Amplifier Class D
$349.99
$429.99
Rockford Fosgate Prime R2-750X1 750W Prime Series Monoblock Subwoofer Class D Amplifier
Primed for performance, the R2-750X1 amplifier is a 750-watt, Class-D, capable of operating at 4Ω, 2Ω, or 1Ω mono. This amplifier is extremely efficient because of its Class-D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allow you to tune the bass for the desired level of the music.
Rockford Fosgate's R2 amplifiers are the building blocks for great audio systems, powerful enough to even DRIVE our Punch speakers and subwoofers. They have undergone an amazing upgrade by packing them with the latest features at an incredible value. Best of all, they are designed and engineered here in Tempe, Arizona.
General Features:
Rockford Fosgate Prime R2-750X1
RMS Power Rating: 4 ohms: 250 watts x 1 channel
RMS Power Rating: 2 ohms: 500 watts x 1 channel
RMS Power Rating: 1 ohm: 750 watts x 1 channel
Total power output: 500 watts
Balanced Differential Inputs with RCA Pass Through Outputs
High-Level Input Capable
Defeatable Auto Turn on Circuit
Features C.L.E.A.N. Set-up
Variable Input Gain adjustment level
R.L.C. Remote Level Control
Variable Infrasonic Filter
Continuously Variable On-Board Punch EQ
Top Mounted Control Panel
Short Circuit & Over Current Protection
CEA-2006 Compliant & CE Compliant
Full Range Class D
Rollback Protection
Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers
Input sensitivity: Low-Level: 150 mV - 4 V
Input sensitivity: High-Level: 450 mV - 12 V
Frequency Response: 20 Hz - 250 Hz
Total Harmonic Distortion (THD): >1%
Crossover Controls: Low-Pass: 50 Hz - 250 Hz
Crossover Controls: Sub Infrasonic: 15 Hz - 40 Hz
Recommended Fuse Rating: 120A
4-gauge power and ground wiring are recommended for installation.
Dimensions: "1.9" x "6.8" x "10.1"
Authorized Internet Dealer
1-Year Manufacturer's Warranty
What is in the R2-750X1 package:
Mono subwoofer amplifier
Wired Remote Level Control module
16' Remote cable (RJ-25 connector on both ends)
One 7" Speaker input harness
3mm Allen Hex key
Four 3/4" Screws
Two 1/2" Screws
5 Flat washers
1 Nut
Installation and Operation Instructions
Certificate of Performance
Rockford Fosgate contact information
Rockford Fosgate R2-500X1 owner's manual
⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.


00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate Prime R2-500X1 Amplifier
500W Prime Series Monoblock Subwoofer Class D Amplifier $249.99 $350.00
500W Prime Series Monoblock Subwoofer Class D Amplifier $249.99 $350.00
Rockford Fosgate Prime R2-500X1 500W Prime Series Monoblock Subwoofer Class D Amplifier
Primed for performance, the R2-500X1 amplifier is a 500 watt, class-D, capable of operating at 4Ω or 2Ω mono. This amplifier is extremely efficient because of its class D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allows you to tune the bass for the desired level for the music.
General Features:
Rockford Fosgate Prime R2-500X1
RMS Power Rating:
4 ohms: 300 watts x 1 chan.
2 ohms: 500 watts x 1 chan.
Total power output: 500 watts
Balanced Differential Inputs with RCA Pass Through Outputs
High-Level Input Capable
Defeat able Auto Turn-On Circuit
Features C.L.E.A.N. Set-up
Variable Input Gain adjustment level
R.L.C. Remote Level Control
Variable Infrasonic Filter
Continuously Variable On Board Punch EQ
Top Mounted Control Panel
Short Circuit & Over Current Protection
CEA-2006 Compliant & CE Compliant
Full Range Class D
Rollback Protection
Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers
Input sensitivity:
Low-Level: 150 mV - 4 V
High-Level: 450 mV - 12 V
Frequency Response: 20 Hz - 250 Hz
Total Harmonic Distortion (THD): >1%
Crossover Controls
Low-Pass: 50 Hz - 250 Hz
Sub Infrasonic: 15 Hz - 40 Hz
Recommended Fuse Rating: 80A
4 gauge power and ground wiring is recommended for installation
Dimensions: "1.9" x "6.8" x "8.5"
Authorized Internet Dealer
1 Year Manufacturer's Warranty
What is in the R2-500X1 package:
Rockford Fosgate R2-500X1 owner's manual
Mono subwoofer amplifier
Wired Remote Level Control module
16' Remote cable (RJ-25 connector on both ends)
One 7" Speaker input harnesses
3mm Allen Hex key
Four 3/4" Screws
Two 1/2" Screws
5 Flat washers
1 Nut
Installation and Operation Instructions
Certificate of Performance
Rockford Fosgate contact information
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca


00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate R2-500X1 Prime 500 Watt 1ohh Mono punch Amplifier Class D | NEW
$249.99
$350.00
Rockford Fosgate Prime R2-500X1 500W Prime Series Monoblock Subwoofer Class D Amplifier
Primed for performance, the R2-500X1 amplifier is a 500 watt, class-D, capable of operating at 4Ω or 2Ω mono. This amplifier is extremely efficient because of its class D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allows you to tune the bass for the desired level for the music.
General Features:
Rockford Fosgate Prime R2-500X1
RMS Power Rating:
4 ohms: 300 watts x 1 chan.
2 ohms: 500 watts x 1 chan.
Total power output: 500 watts
Balanced Differential Inputs with RCA Pass Through Outputs
High-Level Input Capable
Defeat able Auto Turn-On Circuit
Features C.L.E.A.N. Set-up
Variable Input Gain adjustment level
R.L.C. Remote Level Control
Variable Infrasonic Filter
Continuously Variable On Board Punch EQ
Top Mounted Control Panel
Short Circuit & Over Current Protection
CEA-2006 Compliant & CE Compliant
Full Range Class D
Rollback Protection
Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers
Input sensitivity:
Low-Level: 150 mV - 4 V
High-Level: 450 mV - 12 V
Frequency Response: 20 Hz - 250 Hz
Total Harmonic Distortion (THD): >1%
Crossover Controls
Low-Pass: 50 Hz - 250 Hz
Sub Infrasonic: 15 Hz - 40 Hz
Recommended Fuse Rating: 80A
4 gauge power and ground wiring is recommended for installation
Dimensions: "1.9" x "6.8" x "8.5"
Authorized Internet Dealer
1 Year Manufacturer's Warranty
What is in the R2-500X1 package:
Rockford Fosgate R2-500X1 owner's manual
Mono subwoofer amplifier
Wired Remote Level Control module
16' Remote cable (RJ-25 connector on both ends)
One 7" Speaker input harnesses
3mm Allen Hex key
Four 3/4" Screws
Two 1/2" Screws
5 Flat washers
1 Nut
Installation and Operation Instructions
Certificate of Performance
Rockford Fosgate contact information
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca

00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Diamond Audio 1600 Watt Mono Amplifier HX1600.1D
$959.99
$1,400.00
Diamond Audio HX1600.1D 1600 Watt RMS Mono Amplifier
The Diamond Audio HX1600.1D single channel 1600 watt RMS amplifier is specifically designed for extreme use sound systems that need a small size but major power output. This amp will push any subwoofer you give it, and it'll do it all while staying cool with an anodized extruded aluminum heat sink which provides superior thermal performance.
General Features:
Anodized Extruded Aluminum Heat Sink Provides Superior Thermal Performance
4-Layer PCB Board with Balanced Differential Inputs
Full Range Class D IR Chipset
“SNAP” Capacitors used Throughout the Circuit
Audiophile Grade High Tolerance Components
Spring Steel FET Clips Provide a Cleaner Board Design
Illuminated Logo / Fully Concealed Mounting
Output Clip Indicators for Precise Set-Up
Fine Tuned Fully Variable Crossovers and Phase Control
Top Mounted Controls for Convenient Amplifier Adjustment
Specification:RMS Power Rating
RMS Power (4Ω): 700 W RMS
RMS Power (2Ω): 1150 W RMS
RMS Power (1Ω): 1600 W RMS
Type
Topology: Class D
Power Supply
Power Supply: Full PWM
Power Supply Threshold: 10.0VDC-170VDC
Idle Current: (0.7A)
Distortion
THD 4(1KH@4Ω) : 0.01%
S/N Ratio(A weighted@1W): -80dBA
S/N Ratio(A weighted@FP): -95dBA
Input Sensitivity
Low Input Level: 200mV-5.0V
High Input Level: N/A
Input Impedance
Low Input Level: 20 KΩ
High Input Level: N/A
Output Stage
Output Impedance: 0.018 Ω
Damping Factor(50Hz@4Ω): >250
Bandwidth(-3dB): 10Hz-300Hz
Crossover(-12dB/Oct)
Variable High-Pass: N/A
Variable Low-Pass: 30Hz-300Hz
Variable Sub-Sonic: 10Hz-55Hz@12dB
Fuse Ratings
ATC: 40A X 4
Dimensions
Length x Width x Height(Inches): 15.8" x 7.67" x 2"
Length x Width x Height(mm): 402 x 195 x 51.5
⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Diamond Audio HX1600.1D 1600 Watt RMS Mono Amplifier
$959.99
$1,400.00
Diamond Audio HX1600.1D 1600 Watt RMS Mono Amplifier
The Diamond Audio HX1600.1D single channel 1600 watt RMS amplifier is specifically designed for extreme use sound systems that need a small size but major power output. This amp will push any subwoofer you give it, and it'll do it all while staying cool with an anodized extruded aluminum heat sink which provides superior thermal performance.
General Features:
Anodized Extruded Aluminum Heat Sink Provides Superior Thermal Performance
4-Layer PCB Board with Balanced Differential Inputs
Full Range Class D IR Chipset
“SNAP” Capacitors used Throughout the Circuit
Audiophile Grade High Tolerance Components
Spring Steel FET Clips Provide a Cleaner Board Design
Illuminated Logo / Fully Concealed Mounting
Output Clip Indicators for Precise Set-Up
Fine Tuned Fully Variable Crossovers and Phase Control
Top Mounted Controls for Convenient Amplifier Adjustment
Specification:RMS Power Rating
RMS Power (4Ω): 700 W RMS
RMS Power (2Ω): 1150 W RMS
RMS Power (1Ω): 1600 W RMS
Type
Topology: Class D
Power Supply
Power Supply: Full PWM
Power Supply Threshold: 10.0VDC-170VDC
Idle Current: (0.7A)
Distortion
THD 4(1KH@4Ω) : 0.01%
S/N Ratio(A weighted@1W): -80dBA
S/N Ratio(A weighted@FP): -95dBA
Input Sensitivity
Low Input Level: 200mV-5.0V
High Input Level: N/A
Input Impedance
Low Input Level: 20 KΩ
High Input Level: N/A
Output Stage
Output Impedance: 0.018 Ω
Damping Factor(50Hz@4Ω): >250
Bandwidth(-3dB): 10Hz-300Hz
Crossover(-12dB/Oct)
Variable High-Pass: N/A
Variable Low-Pass: 30Hz-300Hz
Variable Sub-Sonic: 10Hz-55Hz@12dB
Fuse Ratings
ATC: 40A X 4
Dimensions
Length x Width x Height(Inches): 15.8" x 7.67" x 2"
Length x Width x Height(mm): 402 x 195 x 51.5
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Diamond Audio MICRO1V2 Monoblock Micro Full Range Class-D Amplifier 500W RMS
$469.99
$939.98
Diamond Audio MICRO1V2 Monoblock 500W RMS Class D Amplifier
Elite sound quality and superior power in an ultra-compact chassis. The Diamond Audio Micro1v2, one channel power amplifier, sets the standard for high-end Harley-specific amplifiers. The sound quality in a small footprint can be found in Diamond Audio’s MICROV2 amplifiers. Featuring ultra-efficient entire Range Class D IR Chipset DirectFET Power Mosfet Output Stage SMD Technology on four layer Glass PC Board ICAD circuit provides superior overload protection, these compact amplifiers deliver immense power for their size! The added feature of advanced Rollback/Thermal protection allows you to enjoy continuous and uninterrupted play without shutting down. Installation possibilities are endless! When looking for quality and performance in a small package, look to MICROV2 from Diamond Audio.
General Features:
Ultra-compact, high-density aluminum alloy chassis provides superior thermal stability.
Four-layer, glass epoxy circuit board for enhanced performance and reliability
Full Range Class D amplifier technology
Balanced differential inputs for superior noise rejection
Input sensitivity from 200mV to 10V accepts Line (RCA) and Speaker level input
Selectable auto-turn-on modes: Signal Sensing (VOX), 12V Remote (REM), and DC offset (DC)
Fully variable, 12dB per octave, electronic crossover
Variable 18dB per octave sub-sonic filter
Adjustable Bass EQ (45Hz: 0dB to +12dB) / remote level control included
Illuminated logo
Specifications:
RMS Power Rating:
RMS Power (2Ω): 300W
RMS Power (4Ω): 175W
Bridged (mono 1Ω): 500W
Bridged (mono 2Ω): 300W
Bridged (mono 4Ω): 175W
Topology: Full Range Class D
Power Supply:
Power Supply: Full PWM
Power Supply Threshold: 10.0VDC - 17.0VDC
Idle Current: (0.7A)
Distortion:
THD 4 (1KHx @ 4Ω): 0.5%
S/N Ratio (A weighted @1W): -85dBA
S/N Ratio (A weighted @FP): -101.1dBA
Input Sensitivity:
Low Input Level: 200mV - 10.0V
High Input Level: N/A
Input Impedance:
Low Input Level: 20KΩ
High Input Level: 20KΩ
Output Stage:
Output Impedance: 0.011Ω
Damping Factor (50Hz@4Ω): >250
Bandwidth (-3dB): 10Hz - 350Hz
Crossover (-12dB/Oct):
Variable High-Pass: N/A
Variable Low-Pass: 40Hz - 400Hz
Variable Sun-Sonic: 10Hz - 55Hz
Fuse Ratings:
ATC: 25A
Dimensions: 7.89” L x 4.0” W x 1.46” H
⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Diamond Audio HXM800.1D Monoblock 800 Watts RMS Class D HXM Series Amplifier
$599.99
$799.99
Diamond Audio HXM800.1D Monoblock 800 Watts RMS Class D HXM Series Amplifier
The Diamond Audio HXM800.1D is a marine-grade motorsport amplifier that boasts 800 watts RMS on a single channel. Perfect for your system that needs to push a subwoofer to the max while using minimal space.
General Features:
Ultra-compact, high-density aluminum alloy chassis provides superior thermal stability.
Four-layer, glass epoxy circuit board for enhanced performance and reliability
Circuit board conformal coated (water resistant) for marine applications
Full Range Class D amplifier technology
Balanced differential inputs for superior noise rejection
Input sensitivity from 200mV to 10V accepts Line (RCA) and Speaker level input
Selectable auto-turn-on modes: Signal Sensing (VOX), 12V Remote (REM) and DC offset (DC)
Fully variable, 12dB per octave, electronic crossover
Variable 18dB per octave sub-sonic filter
Phase adjustable from 0 to 180 degrees
Adjustable Bass EQ (45Hz: 1dB to +12dB) / remote level control included
Built-in BTR Port (MICRO-USB) to connect our optional Bluetooth receiver-controller
Top-mounted controls for convenient adjustment
Integrated soft clip light for quick system set-up
Illuminated logo
RMS Power Rating
RMS Power (1Ω): 800 W X 1
RMS Power (2Ω): 550 W X 1
RMS Power (4Ω): 350 W X 1
Type
Topology: MonoBlock Class D
Power Supply
Power Supply: Full PWM
Power Supply Threshold: 10.0VDC-17.0VDC
Idle Current: (0.7A)
Distortion
THD (1KHz@4Ω) : 0.05%
S/N Ratio (A weighted@1W): -77.2dBA
S/N Ratio (A weighted@FP): -98.9dBA
Input Sensitivity
Low Input Level: .2mV-10.0V
High Input Level: Yes - Up to 25W RMS
Input Impedance
Low Input Level: 22 KΩ
High Input Level: 22 KΩ
Output Stage
Output Impedance: 0.047Ω
Damping Factor (50Hz@4Ω): >250
Bandwidth (-3dB): 10Hz-350Hz
Crossover (-12dB per Octave)
Variable High-Pass: N/A
Variable Low-Pass: 30Hz - 300Hz
Variable Sub-Sonic: 10Hz - 55Hz
Recommended Fuse Rating
ATC: N/A
Dimensions
Length x Width x Height (Inches): 8.56 x 5.27 x 1.75
Length x Width x Height (mm): 297.6 x 133.9 x 44.5
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.


00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Diamond Audio HX1200.1D HEX Series Monoblock Class-D Car Audio Amplifier
$779.99
$1,500.00
Diamond Audio HX1200.1D HEX Series Monoblock Class-D Car Audio Amplifier
It is introducing the all-new range of Diamond Audio HEX series amplifiers, made for ultimate sound quality and performance. It features a four-layer glass epoxy circuit board, top-mounted controls, and a brushed copper look exterior, making it great for a show car.
General Features:
Anodized Extruded Aluminum Heat Sink provides superior thermal performance
4-Layer PCB Board with balanced differential inputs
Full Range Class D IR Chipset
"Snap" capacitors are used throughout the circuit
Audiophile Grade High Tolerance Components
Spring Steel FET Clips provide a cleaner board design
Illuminated logo / fully concealed mounting
Output clip indicators for precise setup
Fine-tuned fully variable crossovers and phase control
Top-mounted controls for convenient amplifier adjustment
Monoblock Class-D Amplifier
RMS Power Rating: 4 Ohm: 540 watts x 1 Channel
RMS Power Rating: 2 Ohm: 870 watts x 1 Channel
RMS Power Rating: 1 Ohm: 1200 watts x 1 Channel
Frequency Response: 10Hz - 300Hz
Variable Low-Pass Filter (12dB/Octave): 30Hz - 300Hz
Variable Sub-Sonic Filter (12dB/Octave): 10Hz - 55Hz
Top Mounted Controls
Anodized Extruded Aluminum Heat Sink
4-Layer PCB Board
Balanced Differential Inputs
Illuminated Logo
Dimensions: 14.2" (362mm) x 7.67" (195mm) x 2" (51.5mm)
1-Year Warranty
What is Included?
One (1) Diamond Audio HX1200.1D HEX Series Monoblock Class-D Car Audio Amplifier
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.