Completed Products (7413)

AudioControl LC7i 6-channel line output converter with bass restoration adds aftermarket subs and amps to a factory system (Black)+ Free Absolute Electrical Tape+ Phone Holder Want to add your own speakers, subs, and amps to a factory system? AudioControl's LC7i 6-channel line output converter (LOC) with bass restoration allows you to add aftermarket amps, speakers, and subs to your car's factory radio, so you can enjoy better and more powerful sound without losing climate controls, voice-activated functions, or other built-in factory features. The LC7i accepts speaker-level signals, so you can use it with just about any setup, even high-powered amplified systems. Summing The LC7i sums its input signals together, even if they've been crossed over for tweeters, mids, and subs by the factory system. That way, you can count on a strong, smooth, full-range signal for your processors and amps. The LC7i features six RCA preamp outputs that'll handle a traditional front/rear/sub setup. Why you have to restore the bass Many factory radios actually turn the bass down as you increase the volume to protect the cheap factory speakers, subsequently removing much of your music's power and punch. AudioControl developed a patent pending AccuBASS™ circuit that restores the bass the factory radio erased, giving you much fuller and more enjoyable sound. The AccuBASS is applied to the subwoofer output channel, so your sub amp can have the entire, restored signal to work with. Level-matching with an LED indicator AudioControl makes it easy: set your factory stereo to about 3/4 maximum volume, turn the output level control of the LC7i until the "Maximized" light begins to flicker, then adjust the gain controls on your amps and you're done. You've level-matched the output of your receiver to the amplifier's input, so you can count on getting maximum performance and minimum noise from your system. Convenience The optional dash-mounted ACR-1 wired remote allows you to adjust the volume of the bass while you're on the go. The speaker-level inputs sense incoming signals and turn on the LC7i, while a built-in 12-volt trigger turns on your amps as well. If your factory system only has channels for front and rear speakers, AutoMode™ will create the output you can use for your subs Product highlights: 6-channel line output converter plus bass restoration 6 speaker-level inputs (each can handle up to 400 watts RMS) internal channel summing AccuBASS™ bass restoration circuitry 6 preamp outputs (up to 8.5 volts RMS) level matching controls with Maximized Indicator LED Other Features: optional wired remote subwoofer level controller available (#161ACR1) AutoMode™ turns 4-channel input to 6-channel output GTO™ signal-sensing turn on 12-volt turn-on lead output recommended fuse rating: 2 amps 8-11/16"W x 1-3/8"H x 6-9/16"D warranty: 5 years 6-Channel line output converter (black) Owner's manual QC checklist Absolute BT1700 Vinyl Electrical Tape is good quality, multi-purpose vinyl insulating tape. It has great resistance to moisture and varying weather conditions. It is a polyvinyl chloride (PVC) tape that is flame-retardant and conformable. Details Resists abrasion, moisture, alkalis, solvents, and acids Flame-retardant and inhibits the corrosion of electrical conductors Made of durable PVC Compatible with rubber and synthetic splicing compounds Withstands a temperature range of 32 to 194 °F (0 to 90 °C) UL Listed, CSA and VDE Certified Specifications Adhesive Type Rubber Application Insulation Brand Absolute Elongation at Break 200 % Maximum Operating Temperature (Celsius) 90 Degree Celsius Maximum Operating Temperature (Fahrenheit) 194 Degree Fahrenheit Minimum Operating Temperature (Fahrenheit) 32 Degree Fahrenheit Overall Length (Imperial) 60 ft Overall Length (Metric) 18 m Overall Width (Imperial) 0.75 in Overall Width (Metric) 19 mm Product Color Black Shelf Life 5 Year Tape Grade General Use ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine S2-S65C 6.5" 2 Way Pair of Component Car Speakers + Alpine S2-S65 6.5" 2 Way Pair of Coaxial Car Speakers Alpine S2-S65C 480W Peak (160W RMS) 6.5" S-Series 2-way Component Speaker System General Features: 6-1/2" 2-way Component System Car Speakers Peak Power Handling: 480 watts per set / 240 watts on each side RMS Power Handling: 160 watts per set / 80 watts on each side Polypropylene cone material Rubber speaker surround High Amplitude Multi-Roll surround technology HI-RES Certified 1" Silk Dome Tweeters Ferrite magnet motor structure Top-mount Depth: 2-5/16" Cutout Dimensions: 5-1/8" Impedance: 4 ohms Frequency Response: 55 - 40000 Hz Sensitivity: 88 dB Authorized Internet Dealer 1-year Manufacturer's Warranty Alpine S2-S65 6.5" 480 Watts S-Series Hi-Res Certified 2 Way Coaxial Car Speakers General Features: 6-1/2" 2-way Coaxial Car Speakers Peak Power Handling: 480 watts per pair / 240 watts each Power Handling RMS: 160 watts per pair / 80 watts each Polypropylene cone material Rubber speaker surround High Amplitude Multi-Roll surround technology HI-RES Certified Optional Grills KTE-S65G available 1" Silk Dome Tweeters Ferrite magnet motor structure Top-mount Depth: 2-5/16" Cutout Dimensions: 5-1/8" Impedance: 4 ohms Frequency Response: 55 - 40000 Hz Sensitivity: 88 dB Authorized Internet Dealer Weight: ‎6.4 pounds Dimensions, ‎16.5 x 8.5 x 5 inches MFR #: S2-S65 1-year Manufacturer's Warranty Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

AudioControl LC7i 6-channel line output converter with bass restoration adds aftermarket subs and amps to a factory system (Black) Want to add your own speakers, subs, and amps to a factory system? AudioControl's LC7i 6-channel line output converter (LOC) with bass restoration allows you to add aftermarket amps, speakers, and subs to your car's factory radio, so you can enjoy better and more powerful sound without losing climate controls, voice-activated functions, or other built-in factory features. The LC7i accepts speaker-level signals, so you can use it with just about any setup, even high-powered amplified systems. Summing The LC7i sums its input signals together, even if they've been crossed over for tweeters, mids, and subs by the factory system. That way, you can count on a strong, smooth, full-range signal for your processors and amps. The LC7i features six RCA preamp outputs that'll handle a traditional front/rear/sub setup. Why you have to restore the bass Many factory radios actually turn the bass down as you increase the volume to protect the cheap factory speakers, subsequently removing much of your music's power and punch. AudioControl developed a patent pending AccuBASS™ circuit that restores the bass the factory radio erased, giving you much fuller and more enjoyable sound. The AccuBASS is applied to the subwoofer output channel, so your sub amp can have the entire, restored signal to work with. Level-matching with an LED indicator AudioControl makes it easy: set your factory stereo to about 3/4 maximum volume, turn the output level control of the LC7i until the "Maximized" light begins to flicker, then adjust the gain controls on your amps and you're done. You've level-matched the output of your receiver to the amplifier's input, so you can count on getting maximum performance and minimum noise from your system. Convenience The optional dash-mounted ACR-1 wired remote allows you to adjust the volume of the bass while you're on the go. The speaker-level inputs sense incoming signals and turn on the LC7i, while a built-in 12-volt trigger turns on your amps as well. If your factory system only has channels for front and rear speakers, AutoMode™ will create the output you can use for your subs Product highlights: 6-channel line output converter plus bass restoration 6 speaker-level inputs (each can handle up to 400 watts RMS) internal channel summing AccuBASS™ bass restoration circuitry 6 preamp outputs (up to 8.5 volts RMS) level matching controls with Maximized Indicator LED Other Features: optional wired remote subwoofer level controller available (#161ACR1) AutoMode™ turns 4-channel input to 6-channel output GTO™ signal-sensing turn on 12-volt turn-on lead output recommended fuse rating: 2 amps 8-11/16"W x 1-3/8"H x 6-9/16"D warranty: 5 years 6-Channel line output converter (black) Owner's manual QC checklist ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

AudioControl The Epicenter Digital Bass Restoration Processor You like all the bumpin' bass you hear in hip hop, rap, and EDM? Well you can put that deep, biting bass into any kind of music — from classical, jazz, and rock to folk and Tejano — with an AudioControl Epicenter bass restoration processor. Most factory radios dial down bass response to protect flimsy speakers, so when you do add a subwoofer, there's no bass to play. The Epicenter will bring it back. AudioControl's legendary Epicenter bass processor maximizes the low-frequency power and punch of your bass system, whether it's a simple powered bass tube or a full-blown competition setup. Simply install this processor between your receiver and your amplifiers or crossovers, and you'll finally be able to hear all the good bass you've been missing. An included wired remote lets you control the amount of thump from the front seat. How does it do it? Sophisticated processing analyzes the incoming signal and synthesizes low-bass fundamental tones, increasing bass response tremendously. The Epicenter connects to any receiver with preamp outputs — its balanced inputs will reject noise from your car's electrical system. A subsonic filter removes extreme low frequencies from your signal so your amps and subs will play more efficiently, while a single band ParaBass equalizer lets you fine-tune the bass tone. Upgrade available AudioControl's Epicenter bass restoration processing is also available in The Epicenter Micro, which features a compact chassis, high-level inputs, and selectable load resistors for better OEM factory system integration. Product highlights: bass restoration processor increases bass response from your system 2-channel preamp inputs and outputs Para-Bass controls adjust center-frequency and width of bass EQ processing fixed subsonic filter (33 Hz, 12/dB octave) wired remote bass level controller frequency response: 10 to 100,000 Hz fuse rating: 1A 8-1/16"W x 1-1/4"H x 6-3/4"H warranty: 5 years Pre-amp Bass Restoration Processor (black) Remote dash mount control 20' RJ-14 cable Owner's manual QC checklist ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

AudioControl The Epicenter® Micro Bass restoration processor and line output converter Add bass to your aftermarket system's high-level sourceMost factory radios dial down deep, low-hitting bass notes to protect flimsy factory speakers. The Epicenter Micro from AudioControl takes amplified speaker-level signals, converts them into the high-quality preamp signals your sub amp needs, and then adds the bass that's missing. Even when listening to traditionally bass-weak classical, jazz, folk, or Tejano music, you'll finally be able to hear all the good bass you've been missing. How does it do it? Sophisticated processing analyzes the incoming signal and synthesizes low-bass fundamental tones, increasing bass response tremendously. A single band ParaBASS® equalizer lets you fine-tune your subwoofer's tone. A selectable subsonic filter removes extremely low frequencies so your amps and subs will play more efficiently. The Epicenter Micro will also connect to any receiver with preamp outputs — its balanced inputs will reject noise from your car's electrical system for ultra-clean output. Installation conveniences The included ACR-4 dash-mount wired remote control allows you to adjust the level of your sub channel on the go. Load selection switches make OEM factory system integration easier, so the Epicenter Micro will work with almost any vehicle's sound system. Selectable turn-on modes include GTO™ Signal Sense (DC offset), audio signal, or remote 12-volt input. Product highlights: active 2-channel line driver/output converter with bass restoration designed to work with aftermarket and factory systems provides up to 9.5 Vrms output (selectable level: 5, 7, 10V) preamp and speaker-level inputs speaker-level inputs handle up to 40V (400 watts RMS) speaker-level inputs feature switchable load resistance (20, 60, or 20,000 ohms) to prevent factory stereo shut-down Epicenter bass restoration increases bass response Para-Bass controls adjust center frequency and width of bass EQ processing More info: ACR-4 wired remote included switchable Programmable Frequency Match (PFM) subsonic filter (20 Hz, 12/dB octave) Selectable ground isolation helps eliminate noise auto turn-on via 12V remote, DC offset, or audio signal detect 12-volt turn-on lead output wiring, fuse, and hardware not included with the device 18-gauge power and ground leads and a 1-amp fuse are recommended dimensions: 5-1/8" W x 1" H x 3" D warranty: 5 years Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

AudioControl The Epicenter® Micro Bass restoration processor Free Absolute Electrical Tape Phone Holder Add bass to your aftermarket system's high-level sourceMost factory radios dial down deep, low-hitting bass notes to protect flimsy factory speakers. The Epicenter Micro from AudioControl takes amplified speaker-level signals, converts them into the high-quality preamp signals your sub amp needs, and then adds the missing bass. Even when listening to traditionally bass-weak classical, jazz, folk, or Tejano music, you'll finally be able to hear all the good bass you've been missing. How does it do it? Sophisticated processing analyzes the incoming signal and synthesizes low-bass fundamental tones, increasing bass response tremendously. A single band ParaBASS® equalizer lets you fine-tune your subwoofer's tone. A selectable subsonic filter removes extremely low frequencies so your amps and subs will play more efficiently. The Epicenter Micro will also connect to any receiver with preamp outputs — its balanced inputs will reject noise from your car's electrical system for ultra-clean output. Installation conveniences The included ACR-4 dash-mount wired remote control allows you to adjust the level of your sub channel on the go. Load selection switches make OEM factory system integration easier, so the Epicenter Micro will work with almost any vehicle's sound system. Selectable turn-on modes include GTO™ Signal Sense (DC offset), audio signal, or remote 12-volt input. Product highlights: active 2-channel line driver/output converter with bass restoration designed to work with aftermarket and factory systems provides up to 9.5 Vrms output (selectable level: 5, 7, 10V) preamp and speaker-level inputs speaker-level inputs handle up to 40V (400 watts RMS) speaker-level inputs feature switchable load resistance (20, 60, or 20,000 ohms) to prevent factory stereo shut-down Epicenter bass restoration increases bass response Para-Bass controls adjust center frequency and width of bass EQ processing More info: ACR-4 wired remote included switchable Programmable Frequency Match (PFM) subsonic filter (20 Hz, 12/dB octave) Selectable ground isolation helps eliminate noise auto turn-on via 12V remote, DC offset, or audio signal detect 12-volt turn-on lead output wiring, fuse, and hardware not included with the device 18-gauge power and ground leads and a 1-amp fuse are recommended dimensions: 5-1/8" W x 1" H x 3" D warranty: 5 years Absolute BT1700 Vinyl Electrical Tape is a good-quality, multi-purpose vinyl insulating tape. It has great resistance to moisture and varying weather conditions. It is a polyvinyl chloride (PVC) tape that is flame-retardant and conformable. Details Resists abrasion, moisture, alkalis, solvents, and acids Flame-retardant and inhibits the corrosion of electrical conductors Made of durable PVC Compatible with rubber and synthetic splicing compounds Withstands a temperature range of 32 to 194°F (0 to 90 °C) UL Listed, CSA and VDE Certified Specifications Adhesive Type Rubber Application Insulation Brand Absolute Elongation at Break 200 % Maximum Operating Temperature (Celsius) 90 degrees Celsius Maximum Operating Temperature (Fahrenheit) 194 degrees Fahrenheit Minimum Operating Temperature (Fahrenheit) 32 degrees Fahrenheit Overall Length (Imperial) 60 ft Overall Length (Metric) 18 m Overall Width (Imperial) 0.75 in Overall Width (Metric) 19 mm Product Color Black Shelf Life 5 Year Tape Grade General Use Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

AudioControl The Epicenter Digital Bass Restoration Processor + Free Absolute Electrical Tape Phone Holder You like all the bumpin' bass you hear in hip hop, rap, and EDM? Well, you can put that deep, biting bass into any music — from classical, jazz, and rock to folk and Tejano — with an AudioControl Epicenter bass restoration processor. Most factory radios dial down bass response to protect flimsy speakers, so when you do add a subwoofer, there's no bass to play. The Epicenter will bring it back. AudioControl's legendary Epicenter bass processor maximizes the low-frequency power and punch of your bass system, whether it's a simple powered bass tube or a full-blown competition setup. Simply install this processor between your receiver and your amplifiers or crossovers, and you'll finally be able to hear all the good bass you've been missing. An included wired remote lets you control the amount of thump from the front seat. How does it do it? Sophisticated processing analyzes the incoming signal and synthesizes low-bass fundamental tones, increasing bass response tremendously. The Epicenter connects to any receiver with preamp outputs — its balanced inputs will reject noise from your car's electrical system. A subsonic filter removes extremely low frequencies from your signal so your amps and subs will play more efficiently, while a single-band ParaBass equalizer lets you fine-tune the bass tone. Upgrade available AudioControl's Epicenter bass restoration processing is also available in The Epicenter Micro, which features a compact chassis, high-level inputs, and selectable load resistors for better OEM factory system integration. Product highlights: bass restoration processor Increase bass response from your system 2-channel preamp inputs and outputs Para-Bass controls adjust the center frequency and width of bass EQ processing fixed subsonic filter (33 Hz, 12/dB octave) Wired remote bass level controller frequency response: 10 to 100,000 Hz fuse rating: 1A 8-1/16"W x 1-1/4"H x 6-3/4"H warranty: 5 years Pre-amp Bass Restoration Processor (black) Remote dash mount control 20' RJ-14 cable Owner's manual QC checklist Absolute BT1700 Vinyl Electrical Tape is a good-quality, multi-purpose vinyl insulating tape. It has excellent resistance to moisture and varying weather conditions. It is a polyvinyl chloride (PVC) tape that is flame-retardant and conformable. Details Resists abrasion, moisture, alkalis, solvents, and acids Flame-retardant and inhibits the corrosion of electrical conductors Made of durable PVC Compatible with rubber and synthetic splicing compounds Withstands a temperature range of 32 to 194°F (0 to 90 °C) UL Listed, CSA and VDE Certified Specifications Adhesive Type Rubber Application Insulation Brand Absolute Elongation at Break 200 % Maximum Operating Temperature (Celsius) 90 degrees Celsius Maximum Operating Temperature (Fahrenheit) 194 degrees Fahrenheit Minimum Operating Temperature (Fahrenheit) 32 degrees Fahrenheit Overall Length (Imperial) 60 ft Overall Length (Metric) 18 m Overall Width (Imperial) 0.75 in Overall Width (Metric) 19 mm Product Color Black Shelf Life 5 Year Tape Grade General Use Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Cerwin Vega EQ770 7-Band Graphic Equalizer with Auxiliary Input+ Free Absolute Electrical Tape+ Phone Holder New EQ for you Maybe you've got an older car stereo system that you want to get more from. Or maybe you've got an all-new setup that you want to get the most out of. In either case,Cerwin Vega EQ770 boasts 7 bands of equalization that'll allow you to fine-tune your sound, along with independent master volume, subwoofer level, and fader controls that'll keep your highs and lows in balance. Ability for adjustability The EQ770 features RCA inputs and high-level speaker inputs, so you can connect it to just about any system. It also features two AUX inputs — RCA jacks in the back and a 1/8" AUX input on the front panel — which you can select with the AUX switch on the front panel. The RCA AUX inputs offer variable gain so you can adjust for audio sources of varying levels, while a selectable low-pass filter at 60 or 90 Hz tames the wilder extremes of bass. The 8-volt outputs ensure that your amplifiers will get a clean, powerful signal for maximum performance. Product highlights: General Features: 7-Band Graphic Equalizer with Auxiliary Input Red illumination Master and subwoofer volume control 3 Sets of up to 7V preamp outputs (front, rear, and subwoofer) Subwoofer frequency and level control Nickel-plated RCA level inputs Nickel-plated screw terminals Built-in fader control Authorized Internet Dealer 1-year Manufacturer's Warranty Product Specifications: Number of Bands: 7 Signal-to-noise ratio: 90dB Frequency response: 10 - 50000Hz Channel separation: 70dB Owner's Manua/Installation Manual Warranty Sheet Absolute BT1700 Vinyl Electrical Tape is good quality, multi-purpose vinyl insulating tape. It has great resistance to moisture and varying weather conditions. It is a polyvinyl chloride (PVC) tape that is flame-retardant and conformable. Details Resists abrasion, moisture, alkalis, solvents, and acids Flame-retardant and inhibits the corrosion of electrical conductors Made of durable PVC Compatible with rubber and synthetic splicing compounds Withstands a temperature range of 32 to 194 °F (0 to 90 °C) UL Listed, CSA and VDE Certified Specifications Adhesive Type Rubber Application Insulation Brand Absolute Elongation at Break 200 % Maximum Operating Temperature (Celsius) 90 Degree Celsius Maximum Operating Temperature (Fahrenheit) 194 Degree Fahrenheit Minimum Operating Temperature (Fahrenheit) 32 Degree Fahrenheit Overall Length (Imperial) 60 ft Overall Length (Metric) 18 m Overall Width (Imperial) 0.75 in Overall Width (Metric) 19 mm Product Color Black Shelf Life 5 Year Tape Grade General Use ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov