All Products (8993)

Alpine R2-W12D4 2250W Max (750W RMS) 12" R-Series Dual 4-Ohm Car Subwoofer + KTE-12G.3 Grille The new 2022 R-Series subwoofers are here - drawing from decades of Subwoofer engineering experience. They deliver deep, clean, accurate bass and feature Alpine’s HAMR Surround for maximum cone excursion, delivering tons of bass output. The new ceramic dust cap is lightweight and rigid, keeping distortion at an absolute minimum. The enlarged motor structure ensures better woofer control for a strong, clean bass response. General Features: 12" Dual 4 ohm Type-R Subwoofer Peak Power Handling: 2250watts RMS Power Handling: 750 watts Recommended power range: 300 - 750W RMS CTA-2031 compliant power ratings Parabolic pulp/kevlar cone H.A.M.R. surround Polypropylene, mica, and talc dust cap Reinforced cone neck and spider joint Cast aluminum frame with integral shorting sleeve 8AWG push terminals with VC configuration jumpers 2.6" High excursion overhung voice coil 127 oz. Strontium ferrite segmented magnet Top-mount depth: 6-3/8" Cutout diameter: 10-7/8" Frequency Response: 24 - 200Hz Sensitivity: 84.3dB Resonance Frequency (Fs): 27Hz Authorized Dealer 1-year Manufacturer's Warranty What's in the R2-W12D4 package: R2-W12D2 owner's manual One 12" Dual 4-ohm voice coil subwoofer Two 3" jumper cables R-Series Subwoofer Application Guide Online product registration information Warranty Information https://www.youtube.com/watch?v=ihjWBSOYVxE&t=179s ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

2 Alpine R2-W10D4 10" R-Series next generation 4 Ohm 2250 Max, 750W RMS DVC Car Audio Subwoofer + KTE-10G.3 Grills The new 2022 R-Series subwoofers are here - drawing from decades of Subwoofer engineering experience. They deliver deep, clean, accurate bass and feature Alpine’s HAMR Surround for maximum cone excursion, delivering tons of bass output. The new ceramic dust cap is lightweight and rigid, keeping distortion at an absolute minimum. The enlarged motor structure ensures better woofer control for a strong, clean bass response. General Features: 10" Dual 4 ohms Type-R Series Series Subwoofer RMS Power Handling: 750 watts Peak Power Handling: 2250 watts Kevlar Reinforced Pulp Paper Cone High-Amplitude Multi-Roll (H.A.M.R) Surround Push-Type Speaker Terminals (Up To 8AWG Wire Size) Oversized Dust Cap 2.6" High-Temperature Voice coil 20 mm Xmax 123 oz. Double Stacked Ferrite magnet motor structure Frequency Response: 26 - 200 Hz Resonance Frequency (Fs): 32 Hz Sensitivity: 82.8 dB Sealed box volume: .4 cubic feet - .85 cubic feet Ported box volume: .75 cubic feet - 1.3 cubic feet Top-mount depth: 6" Cutout diameter: 9.6" CTA-2031 Compliant: Yes Authorized Internet Dealer Alpine KTE-10G Optional Protective subwoofer grille 1-year Manufacturer's Warranty What is in the R2-W10D4 package: R2-W10D4 owner's manual One 10" Dual 4-ohm voice coil subwoofer Plastic trim ring Two 4.5" jumper wires Application guide Online product registration information Warranty Information  Important Notice  ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine S-W10D2 1800W Max (600W RMS) 10" S-Series Dual 2 Ohm Car Subwoofer with Absolute VGS10 Ported Subwoofer Box Alpine introduces the all-new S-Series Subwoofers; their unique design substantially improves bass output and provides installation versatility. Each S-Series subwoofer uses a custom-stamped steel frame and is available in twelve, ten, and eight-inch. These high-strength frames were designed to withstand the rigors of the improved S-Series motor. They have frame leg vents, a vented back plate to help cool the subwoofer voice coil and motor parts, and a shallow design to help fit in smaller spaces. The S-Series Subwoofers incorporate two strontium ferrite magnets stacked together, providing increased motor strength and excursion, ultimately delivering an accurate bass to your music. The convenient push-type insert terminals with a dual voice coil jumper system will significantly reduce installation time. Just strip the speaker insulation at the wire end, then insert the bare wire into the hole of the spring-loaded push terminal. At the same time, the concealed mount gasket system creates a clean, finished appearance for any vehicle. General Features: 10" 2 ohm S-Series (Type-S) Subwoofer RMS Power Handling: 600 watts Peak Power Handling: 1800 watts  Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 4-11/16" Cutout diameter: 8-13/16 Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 33 Hz Authorized Dealer 1-year Manufacturer's Warranty What is in the S-W10D2 package: S-W10D2 owner's manual One 10" Dual 2-ohm voice coil subwoofer 1 Rubber concealing ring Two 3" jumper cables (each has a single banana connector on each end) Subwoofer Application Guide Online product registration information Warranty Information ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine S-W10D2 1800W Max (600W RMS) 10" S-Series Dual 2 Ohm Car Subwoofer with Absolute SS10 Sealed Subwoofer Box Alpine introduces the all-new S-Series Subwoofers; their unique design substantially improves bass output and provides installation versatility. Each S-Series subwoofer uses a custom-stamped steel frame and is available in twelve, ten, and eight-inch. These high-strength frames were designed to withstand the rigors of the improved S-Series motor. They have frame leg vents, a vented back plate to help cool the subwoofer voice coil and motor parts, and a shallow design to help fit in smaller spaces. The S-Series Subwoofers incorporate two strontium ferrite magnets stacked together, providing increased motor strength and excursion, ultimately delivering an accurate bass to your music. The convenient push-type insert terminals with a dual voice coil jumper system will significantly reduce installation time. Just strip the speaker insulation at the wire end, then insert the bare wire into the hole of the spring-loaded push terminal. At the same time, the concealed mount gasket system creates a clean, finished appearance for any vehicle. General Features: 10" 2 ohm S-Series (Type-S) Subwoofer RMS Power Handling: 600 watts Peak Power Handling: 1800 watts  Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 4-11/16" Cutout diameter: 8-13/16 Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 33 Hz Authorized Dealer 1-year Manufacturer's Warranty What is in the S-W10D2 package: S-W10D2 owner's manual One 10" Dual 2-ohm voice coil subwoofer 1 Rubber concealing ring Two 3" jumper cables (each has a single banana connector on each end) Subwoofer Application Guide Online product registration information Warranty Information ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

2 Alpine S-W10D2 1800W Max (600W RMS) 10" S-Series Dual 2 Ohm Car Subwoofer  with Absolute TW500 Tweeter & BT1700 Electrical Tape & Mobile Holder   Alpine introduces the all-new S-Series Subwoofers; their unique design substantially improves bass output and provides installation versatility. Each S-Series subwoofer uses a custom-stamped steel frame and is available in twelve, ten, and eight-inch. These high-strength frames were designed to withstand the rigors of the improved S-Series motor. They have frame leg vents, a vented back plate to help cool the subwoofer voice coil and motor parts, and a shallow design to help fit in smaller spaces. The S-Series Subwoofers incorporate two strontium ferrite magnets stacked together, providing increased motor strength and excursion, ultimately delivering an accurate bass to your music. The convenient push-type insert terminals with a dual voice coil jumper system will significantly reduce installation time. Just strip the speaker insulation at the wire end, then insert the bare wire into the hole of the spring-loaded push terminal. At the same time, the concealed mount gasket system creates a clean, finished appearance for any vehicle. General Features: 10" 2 ohm S-Series (Type-S) Subwoofer RMS Power Handling: 600 watts Peak Power Handling: 1800 watts  Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 4-11/16" Cutout diameter: 8-13/16 Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 33 Hz Authorized Dealer 1-year Manufacturer's Warranty What is in the S-W10D2 package: S-W10D2 owner's manual One 10" Dual 2-ohm voice coil subwoofer 1 Rubber concealing ring Two 3" jumper cables (each has a single banana connector on each end) Subwoofer Application Guide Online product registration information Warranty Information ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine KTA-200M Mono Power Pack Class-D Amp with Alpine S-W10D2 10" Subwoofer This bundle includes an Alpine KTA-200M Mono 400-Watt Power Pack Amplifier, an Alpine S-W10D2 S-Series 10" Dual 2-Ohm Subwoofer. Alpine KTA-200M Compact 200 watts RMS Class D Monoblock Power Pack Amplifier General Features: Power Stack capable with the Alpine iLX-W650 compact mono subwoofer amplifier Alpine’s Class D Amplifier Circuit with DPP Dynamic Peak Power (DPP) technology adds a burst of power when needed CTA-2006 compliant 100W x 1 RMS @ 4Ω, Power Outputs 200W x 1 RMS @ 2Ω, Power Outputs 400W x 1 DPP @ 4Ω, Power Outputs Signal to Noise Ratio 85dB (ref. 1W into 4Ω) ≤0.1% THD+N (ref. 10W into 2Ω) Single-side 22-pin connector selectable low-pass filter (60, 80, 120 Hz at 12 dB/octave) preamp and speaker-level inputs RCA inputs (selectable, Low range=0.2-4V) Sound controls; Crossovers-Off/60Hz/80Hz/120Hz Linkwitz Riley LP Filter @ -24dB/Oct. (selectable); Input gain setting (variable) wiring, hardware, and fuse not included with the amplifier Power Stack bracket included for mounting amp behind Alpine iLX-W650 digital multimedia receiver Authorized Dealer 1-year Warranty Alpine S-W10D2 S-Series 10" Subwoofer with Dual 2-Ohm Voice Coils. General Features: 10" 2 ohm S-Series (Type-S) Subwoofer RMS Power Handling: 600 watts Peak Power Handling: 1800 watts  Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 4-11/16" Cutout diameter: 8-13/16 Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 33 Hz Authorized Dealer 1-year Manufacturer's Warranty Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Mackie Thump 118S 1400W 18" Powered PA Subwoofer + Cover & MR DJ Pole and 6 Feet XLR Cable The Mackie Thump118S subwoofer delivers 1400W of raw wall-shaking power to your system. It has selectable voicing modes and a variable crossover to simplify optimization. The flagship subwoofer of the Thump Series, the 1400W Thump118S delivers maximum performance for modern DJs, bands, and clubs. An all-new design features selectable voicing modes that make it easy to tailor the bass to your needs and style. Welcome to the world of Thump, where rumble rules and the music doesn't stop till you say so. Before you get the party started, equip your system with a subwoofer that can keep up. Thump118S brings 1400W of raw wall-shaking power to your system with selectable voicing modes and a variable crossover to simplify optimization. Stereo inputs plus High-Pass and Full-Range outputs offer plenty of configuration flexibility, and integrated top-corner handles are our most ergonomic design yet. So grab one (or two, or three)  General Features: 1400W Ultra-Efficient Class-D Amplifier Voicing Modes Optimize Thump118S to Your Needs Variable Crossover and Level Stereo XLR Inputs and Stereo High-Pass + Full-Range Outputs Frequency Response: 30Hz - 200Hz Max SPL: 132 dB Frequency response: 30Hz - 200Hz Max SPL: 132 dB Variable level control (-6dBU to +6dBU) Front LED On/Off Weight: 65.5 lb / 29.71 kg Dimensions: 21.3 x 20.9 x 23.9 in / 541 x 531 x 607 mm (HxWxD) Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Mackie Thump 118S 1400W 18" Powered PA Subwoofer + 2 MR DJ 6 Feet XLR Cables The Mackie Thump118S subwoofer delivers 1400W of raw wall-shaking power to your system. It has selectable voicing modes and a variable crossover to simplify optimization. The flagship subwoofer of the Thump Series, the 1400W Thump118S delivers maximum performance for modern DJs, bands, and clubs. An all-new design features selectable voicing modes that make it easy to tailor the bass to your needs and style. Welcome to the world of Thump, where rumble rules and the music doesn't stop till you say so. Before you get the party started, equip your system with a subwoofer that can keep up. Thump118S brings 1400W of raw wall-shaking power to your system with selectable voicing modes and a variable crossover to simplify optimization. Stereo inputs plus High-Pass and Full-Range outputs offer plenty of configuration flexibility, and integrated top-corner handles are our most ergonomic design yet. So grab one (or two, or three)  General Features: 1400W Ultra-Efficient Class-D Amplifier Voicing Modes Optimize Thump118S to Your Needs Variable Crossover and Level Stereo XLR Inputs and Stereo High-Pass + Full-Range Outputs Frequency Response: 30Hz - 200Hz Max SPL: 132 dB Frequency response: 30Hz - 200Hz Max SPL: 132 dB Variable level control (-6dBU to +6dBU) Front LED On/Off Weight: 65.5 lb / 29.71 kg Dimensions: 21.3 x 20.9 x 23.9 in / 541 x 531 x 607 mm (HxWxD) Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Mackie Thump215XT 1400W 15" Powered PA Loudspeaker System with DSP and Bluetooth Enhance your next set with Thump215XT, the next evolution of our full-featured Thump Series powered loudspeakers. Packed with more time-saving features than ever, tons of power, and an all-new cabinet, Thump215XT is the ultimate loudspeaker for DJs, bands, and clubs that need pro sound without the insane price tag. General Features: 1400W ultra-efficient Class-D amplifier. Built-Like-A-Tank to conquer every gig while lightweight for easy loading. Frequency response: 40 Hz - 20kHz. 15" high-performance woofer. 1" compression driver. 4 Application-specific voicing modes. Outdoor mode optimizes voicing for open-air venues. Bluetooth connectivity for streaming, speaker linking, and control. Flexible I/O. Built-in Feedback Eliminator reduces squeals and out-of-control rumble. Music Ducking mode automatically reduces the level of Ch.2 when Ch.1 receives the signal. Front LED On/Off switch. Universal Power Supply (100-240VAC.) Standard pole mount. M10 fly points for permanent installation. The monitor wedge provides an optimal angle for use as a floor monitor. Powered: Yes Channels:2-channel mixer LF Driver Size:15" high-performance woofer HF Driver Size:1" compression driver Total Power:1400W Inputs:2 x XLR-1/4" combo, 1 x 1/8" TRS Outputs:1 x 1/4" Bluetooth: Yes Wireless: Bluetooth Frequency Response:40Hz-20kHz Maximum Peak SPL:129dB SPL Software: Thump Connect 2 App Mounting Options: Pole Mount, Floor Wedge, M10 fly points Power Source: Standard IEC AC cable Height:27.4" Width:17.3" Depth:14" Weight:32.6 lbs. Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Mackie Thump GO 200-watt 8" 2-way Battery-powered portable loudspeaker +MR DJ stand Built to make your life a whole lot easier, Thump GO offers a lightning-fast setup and simple-yet-powerful sound processing, plus flexible inputs, Bluetooth® streaming, and wireless control via the Thump Connect 2 app. Most importantly, Thump GO will amplify the real you with clear, punchy, and accurate sound wherever you call your stage. Take the performance of the renowned Thump Series anywhere with Thump GO. BATTERY POWERFUL Pair a Bluetooth® enabled device with your Thump Go speaker, and you'll be dancing in no time. Thump Go brings the signature Thump punch and clarity in an ultra-portable design with a removable battery pack so you can sound your best anywhere for up to 12 hours on a Single Charge. BUILT-IN 2-CHANNEL MIXER Mic, guitar, keyboard, you made it. Just plug in, and you are good to go. Pull up the Thump Connect 2 app and get your sound dialed in just right, or even stream some backing tracks from your phone General Features: 2-Mackie Thump Go 8" Portable Battery-Powered Loudspeaker Ultra-efficient 200W Class-D amplifier 8” Custom high-output woofer 1" Compression driver Removable lithium-ion battery (included) Tri-color battery life indicator Up to 12 hours of battery life Bluetooth® connectivity for music streaming Wireless control via the Thump Connect 2 app Link to a second Thump GO via Bluetooth for music playback and control 2-channel digital mixer with XLR mix output Feedback Eliminator prevents nasty squeals and unwanted rumbles Four application-specific speaker modes Music Ducking mode automatically lowers Ch.2 level when Ch.1 receives a signal Indoor / Outdoor voicing modes Precision digital crossover and driver alignment Smart input and thermal limiters Durable, lightweight molded enclosure 45-degree monitor angle Built-in pole mount Rugged powder-coated steel grille Weight: 17.6 lb / 8 kg Dimensions (HxWxD): 18 x 9.1 x 11.2 in / 457 x 230 x 285 ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Mackie Thump GO 200-watt 8" 2-way Battery-powered portable loudspeaker +MR DJ stand and 2 MR DJ 6' 1/4' to 1/4' cable Built to make your life a whole lot easier, Thump GO offers a lightning-fast setup and simple-yet-powerful sound processing, plus flexible inputs, Bluetooth® streaming, and wireless control via the Thump Connect 2 app. Most importantly, Thump GO will amplify the real you with clear, punchy, and accurate sound wherever you call your stage. Take the performance of the renowned Thump Series anywhere with Thump GO. BATTERY POWERFUL Pair a Bluetooth® enabled device with your Thump Go speaker, and you'll be dancing in no time. Thump Go brings the signature Thump punch and clarity in an ultra-portable design with a removable battery pack so you can sound your best anywhere for up to 12 hours on a Single Charge. BUILT-IN 2-CHANNEL MIXER Mic, guitar, keyboard, you made it. Just plug in, and you are good to go. Pull up the Thump Connect 2 app and get your sound dialed in just right, or even stream some backing tracks from your phone General Features: 2-Mackie Thump Go 8" Portable Battery-Powered Loudspeaker Ultra-efficient 200W Class-D amplifier 8” Custom high-output woofer 1" Compression driver Removable lithium-ion battery (included) Tri-color battery life indicator Up to 12 hours of battery life Bluetooth® connectivity for music streaming Wireless control via the Thump Connect 2 app Link to a second Thump GO via Bluetooth for music playback and control 2-channel digital mixer with XLR mix output Feedback Eliminator prevents nasty squeals and unwanted rumbles Four application-specific speaker modes Music Ducking mode automatically lowers Ch.2 level when Ch.1 receives a signal Indoor / Outdoor voicing modes Precision digital crossover and driver alignment Smart input and thermal limiters Durable, lightweight molded enclosure 45-degree monitor angle Built-in pole mount Rugged powder-coated steel grille Weight: 17.6 lb / 8 kg Dimensions (HxWxD): 18 x 9.1 x 11.2 in / 457 x 230 x 285 ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.