All Car Amplifiers (436)

Alpine S2-A36F 600W Next Generation S-Series Hi Res Class-D 4-Channel Car Amplifier & Absolute KIT4 4 Gauge / 2000 Watt Complete Amplifier Hookup Installation Kit Bundle The next generation of Alpine S-Series amplifiers is designed to take your car audio experience to the next level without breaking the bank. With a sleek new redesign and upgraded features from their predecessors, these amplifiers offer exceptional performance and power on an affordable budget.The S-Series S2-A36F 4-channel amplifier delivers 60 Watts RMS @4 Ohms or 90 Watts RMS @2 Ohms of pristine high-fidelity signal to your car's front and rear speakers, adding sweet, clear sound to your vehicle.The amp brings your music to life by being Hi-Res Audio certified, with its precise details and emotional power revealed with a frequency response up to 40kHz. For a 3-channel 2-way system, you could also use the amp to drive a pair of front speakers with 60 Watts RMS each while powering a subwoofer with 180 Watts RMS from the bridged rear channels. A variable mid-bass boost on those rear channels allows you to dial in some extra kick and impact to your system's low-frequency sound. You can even add the optional wired remote RUX-KNOB2 to control the level of the rear channels from your front seat.High- and low-pass filters put you in command of the frequency spectrum that reaches your speakers and subs. The amp includes preamp- and speaker-level inputs so you can install it in almost any vehicle, even with a factory radio. When using the speaker-level inputs, the amp can sense the incoming signal and turn itself on, eliminating the need to run a separate turn-on wire to the receiver or fuse box. General Features: Hi-Res Audio Certified (Up to 40kHz) Power Rating: 14.4V, < 0.3% THD +N Power Output: 60W RMS x 4 @ 4Ω, 90W RMS x 4 @ 2Ω Bridged Power: 180W RMS x 2 @ 4Ω 4-Channel Amplifier Alpine’s Class D Amplifier Circuit Two-sided terminal layout Built-in Selectable/ Adjustable Crossovers Mid-Bass EQ Input for more power Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately) Dimensions: 8.7” W x 2.25” H x 8.25” D Weight: 4 lbs, 13 oz S/N Ratio: >83dB Frequency Response: 20Hz – 40kHz Damping Factor: >100 Owner’s Manual 4 Self-tapping screws Hexagon wrench What is in the S2-A36F package: S2-A36F owner's manual 4-Channel amplifier 2 End caps Four 3/4" screws Four 1/4" screws 2mm Allen key Owner's manual Alpine Verification Certificate Warranty information Power supply note Online product registration information Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-A36F 600W Next Generation S-Series Hi Res Class-D 4-Channel Car Amplifier & Absolute KIT8 8 Gauge / 1000 Watt Complete Amplifier Hookup Installation Kit Bundle The next generation of Alpine S-Series amplifiers is designed to take your car audio experience to the next level without breaking the bank. With a sleek new redesign and upgraded features from their predecessors, these amplifiers offer exceptional performance and power on an affordable budget.The S-Series S2-A36F 4-channel amplifier delivers 60 Watts RMS @4 Ohms or 90 Watts RMS @2 Ohms of pristine high-fidelity signal to your car's front and rear speakers, adding sweet, clear sound to your vehicle.The amp brings your music to life by being Hi-Res Audio certified, with its precise details and emotional power revealed with a frequency response up to 40kHz. For a 3-channel 2-way system, you could also use the amp to drive a pair of front speakers with 60 Watts RMS each while powering a subwoofer with 180 Watts RMS from the bridged rear channels. A variable mid-bass boost on those rear channels allows you to dial in some extra kick and impact to your system's low-frequency sound. You can even add the optional wired remote RUX-KNOB2 to control the level of the rear channels from your front seat.High- and low-pass filters put you in command of the frequency spectrum that reaches your speakers and subs. The amp includes preamp- and speaker-level inputs so you can install it in almost any vehicle, even with a factory radio. When using the speaker-level inputs, the amp can sense the incoming signal and turn itself on, eliminating the need to run a separate turn-on wire to the receiver or fuse box. General Features: Hi-Res Audio Certified (Up to 40kHz) Power Rating: 14.4V, < 0.3% THD +N Power Output: 60W RMS x 4 @ 4Ω, 90W RMS x 4 @ 2Ω Bridged Power: 180W RMS x 2 @ 4Ω 4-Channel Amplifier Alpine’s Class D Amplifier Circuit Two-sided terminal layout Built-in Selectable/ Adjustable Crossovers Mid-Bass EQ Input for more power Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately) Dimensions: 8.7” W x 2.25” H x 8.25” D Weight: 4 lbs, 13 oz S/N Ratio: >83dB Frequency Response: 20Hz – 40kHz Damping Factor: >100 Owner’s Manual 4 Self-tapping screws Hexagon wrench What is in the S2-A36F package: S2-A36F owner's manual 4-Channel amplifier 2 End caps Four 3/4" screws Four 1/4" screws 2mm Allen key Owner's manual Alpine Verification Certificate Warranty information Power supply note Online product registration information Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-A36F 600W Next Generation S-Series Hi Res Class-D 4-Channel Car Amplifier & Absolute KIT10 10 Gauge / 800 Watt Complete Amplifier Hookup Installation Kit Bundle The next generation of Alpine S-Series amplifiers is designed to take your car audio experience to the next level without breaking the bank. With a sleek new redesign and upgraded features from their predecessors, these amplifiers offer exceptional performance and power on an affordable budget.The S-Series S2-A36F 4-channel amplifier delivers 60 Watts RMS @4 Ohms or 90 Watts RMS @2 Ohms of pristine high-fidelity signal to your car's front and rear speakers, adding sweet, clear sound to your vehicle.The amp brings your music to life by being Hi-Res Audio certified, with its precise details and emotional power revealed with a frequency response up to 40kHz. For a 3-channel 2-way system, you could also use the amp to drive a pair of front speakers with 60 Watts RMS each while powering a subwoofer with 180 Watts RMS from the bridged rear channels. A variable mid-bass boost on those rear channels allows you to dial in some extra kick and impact to your system's low-frequency sound. You can even add the optional wired remote RUX-KNOB2 to control the level of the rear channels from your front seat.High- and low-pass filters put you in command of the frequency spectrum that reaches your speakers and subs. The amp includes preamp- and speaker-level inputs so you can install it in almost any vehicle, even with a factory radio. When using the speaker-level inputs, the amp can sense the incoming signal and turn itself on, eliminating the need to run a separate turn-on wire to the receiver or fuse box. General Features: Hi-Res Audio Certified (Up to 40kHz) Power Rating: 14.4V, < 0.3% THD +N Power Output: 60W RMS x 4 @ 4Ω, 90W RMS x 4 @ 2Ω Bridged Power: 180W RMS x 2 @ 4Ω 4-Channel Amplifier Alpine’s Class D Amplifier Circuit Two-sided terminal layout Built-in Selectable/ Adjustable Crossovers Mid-Bass EQ Input for more power Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately) Dimensions: 8.7” W x 2.25” H x 8.25” D Weight: 4 lbs, 13 oz S/N Ratio: >83dB Frequency Response: 20Hz – 40kHz Damping Factor: >100 Owner’s Manual 4 Self-tapping screws Hexagon wrench What is in the S2-A36F package: S2-A36F owner's manual 4-Channel amplifier 2 End caps Four 3/4" screws Four 1/4" screws 2mm Allen key Owner's manual Alpine Verification Certificate Warranty information Power supply note Online product registration information Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-S65C 6.5" Component Set & S2-S69 6x9" Coaxial Speaker & S2-A36F 4 Gauge Amplifier & Absolute TW500 Piezo Super Dome Tweeter &  Electrical Tape & Cell phone Mobile Bracket Bundle Alpine S2-A36F 600W Next Generation S-Series Hi Res Class-D 4-Channel Car Amplifier The next generation of Alpine S-Series amplifiers is designed to take your car audio experience to the next level without breaking the bank. With a sleek new redesign and upgraded features from their predecessors, these amplifiers offer exceptional performance and power on an affordable budget.The S-Series S2-A36F 4-channel amplifier delivers 60 Watts RMS @4 Ohms or 90 Watts RMS @2 Ohms of pristine high-fidelity signal to your car's front and rear speakers, adding sweet, clear sound to your vehicle. General Features: Hi-Res Audio Certified (Up to 40kHz) Power Rating: 14.4V, < 0.3% THD +N Power Output: 60W RMS x 4 @ 4Ω, 90W RMS x 4 @ 2Ω Bridged Power: 180W RMS x 2 @ 4Ω 4-Channel Amplifier Alpine’s Class D Amplifier Circuit Two-sided terminal layout Built-in Selectable/ Adjustable Crossovers Mid-Bass EQ Input for more power Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately) Dimensions: 8.7” W x 2.25” H x 8.25” D Weight: 4 lbs, 13 oz S/N Ratio: >83dB Frequency Response: 20Hz – 40kHz Damping Factor: >100 Owner’s Manual 4 Self-tapping screws Hexagon wrench Alpine S2-S65C 480W Peak (160W RMS) 6.5" S-Series 2-way Component Speaker System General Features: 6-1/2" 2-way Component System Car Speakers Peak Power Handling: 480 watts per set / 240 watts on each side RMS Power Handling: 160 watts per set / 80 watts on each side Polypropylene cone material Rubber speaker surround High Amplitude Multi-Roll surround technology HI-RES Certified 1" Silk Dome Tweeters Ferrite magnet motor structure Top-mount Depth: 2-5/16" Cutout Dimensions: 5-1/8" Impedance: 4 ohms Frequency Response: 55 - 40000 Hz Sensitivity: 88 dB Authorized Internet Dealer 1-year Manufacturer's Warranty Alpine S2-S69 260 Watts S-Series 6x9" 2-Way Hi-Res Car Audio Coaxial Speakers General Features: 6" x 9" 2-way Coaxial Car Speakers Peak Power Handling: 520 watts per pair / 260 watts each RMS Power Handling: 170 watts per pair / 85 watts each Polypropylene cone material Rubber speaker surround High Amplitude Multi-Roll surround technology HI-RES Certified 1" Silk Dome Tweeters Large Ferrite magnet structure Top-mount Depth: 3" Cutout Dimensions: 5-29/32 x 8-3/4  Impedance: 4 ohms Frequency Response: 65 - 40000 Hz Sensitivity: 88 dB Authorized Internet Dealer MFR #: S2-S69 1-year Manufacturer's Warranty Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-S65C 6.5" Component Set & S2-S69 6x9" Coaxial Speaker & S2-A36F 4 Gauge Amplifier Alpine S2-A36F 600W Next Generation S-Series Hi Res Class-D 4-Channel Car Amplifier The next generation of Alpine S-Series amplifiers is designed to take your car audio experience to the next level without breaking the bank. With a sleek new redesign and upgraded features from their predecessors, these amplifiers offer exceptional performance and power on an affordable budget.The S-Series S2-A36F 4-channel amplifier delivers 60 Watts RMS @4 Ohms or 90 Watts RMS @2 Ohms of pristine high-fidelity signal to your car's front and rear speakers, adding sweet, clear sound to your vehicle. General Features: Hi-Res Audio Certified (Up to 40kHz) Power Rating: 14.4V, < 0.3% THD +N Power Output: 60W RMS x 4 @ 4Ω, 90W RMS x 4 @ 2Ω Bridged Power: 180W RMS x 2 @ 4Ω 4-Channel Amplifier Alpine’s Class D Amplifier Circuit Two-sided terminal layout Built-in Selectable/ Adjustable Crossovers Mid-Bass EQ Input for more power Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately) Dimensions: 8.7” W x 2.25” H x 8.25” D Weight: 4 lbs, 13 oz S/N Ratio: >83dB Frequency Response: 20Hz – 40kHz Damping Factor: >100 Owner’s Manual 4 Self-tapping screws Hexagon wrench Alpine S2-S65C 480W Peak (160W RMS) 6.5" S-Series 2-way Component Speaker System General Features: 6-1/2" 2-way Component System Car Speakers Peak Power Handling: 480 watts per set / 240 watts on each side RMS Power Handling: 160 watts per set / 80 watts on each side Polypropylene cone material Rubber speaker surround High Amplitude Multi-Roll surround technology HI-RES Certified 1" Silk Dome Tweeters Ferrite magnet motor structure Top-mount Depth: 2-5/16" Cutout Dimensions: 5-1/8" Impedance: 4 ohms Frequency Response: 55 - 40000 Hz Sensitivity: 88 dB Authorized Internet Dealer 1-year Manufacturer's Warranty Alpine S2-S69 260 Watts S-Series 6x9" 2-Way Hi-Res Car Audio Coaxial Speakers General Features: 6" x 9" 2-way Coaxial Car Speakers Peak Power Handling: 520 watts per pair / 260 watts each RMS Power Handling: 170 watts per pair / 85 watts each Polypropylene cone material Rubber speaker surround High Amplitude Multi-Roll surround technology HI-RES Certified 1" Silk Dome Tweeters Large Ferrite magnet structure Top-mount Depth: 3" Cutout Dimensions: 5-29/32 x 8-3/4  Impedance: 4 ohms Frequency Response: 65 - 40000 Hz Sensitivity: 88 dB Authorized Internet Dealer MFR #: S2-S69 1-year Manufacturer's Warranty Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-S65C 6.5" Component Set & S2-S69 6x9" Coaxial Speaker & S2-A36F 4 Gauge Amplifier & Absolute KIT4 4 Gauge / 2000 Watt Complete Amplifier Hookup Installation Kit Bundle Alpine S2-A36F 600W Next Generation S-Series Hi Res Class-D 4-Channel Car Amplifier The next generation of Alpine S-Series amplifiers is designed to take your car audio experience to the next level without breaking the bank. With a sleek new redesign and upgraded features from their predecessors, these amplifiers offer exceptional performance and power on an affordable budget.The S-Series S2-A36F 4-channel amplifier delivers 60 Watts RMS @4 Ohms or 90 Watts RMS @2 Ohms of pristine high-fidelity signal to your car's front and rear speakers, adding sweet, clear sound to your vehicle. General Features: Hi-Res Audio Certified (Up to 40kHz) Power Rating: 14.4V, < 0.3% THD +N Power Output: 60W RMS x 4 @ 4Ω, 90W RMS x 4 @ 2Ω Bridged Power: 180W RMS x 2 @ 4Ω 4-Channel Amplifier Alpine’s Class D Amplifier Circuit Two-sided terminal layout Built-in Selectable/ Adjustable Crossovers Mid-Bass EQ Input for more power Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately) Dimensions: 8.7” W x 2.25” H x 8.25” D Weight: 4 lbs, 13 oz S/N Ratio: >83dB Frequency Response: 20Hz – 40kHz Damping Factor: >100 Owner’s Manual 4 Self-tapping screws Hexagon wrench Alpine S2-S65C 480W Peak (160W RMS) 6.5" S-Series 2-way Component Speaker System General Features: 6-1/2" 2-way Component System Car Speakers Peak Power Handling: 480 watts per set / 240 watts on each side RMS Power Handling: 160 watts per set / 80 watts on each side Polypropylene cone material Rubber speaker surround High Amplitude Multi-Roll surround technology HI-RES Certified 1" Silk Dome Tweeters Ferrite magnet motor structure Top-mount Depth: 2-5/16" Cutout Dimensions: 5-1/8" Impedance: 4 ohms Frequency Response: 55 - 40000 Hz Sensitivity: 88 dB Authorized Internet Dealer 1-year Manufacturer's Warranty Alpine S2-S69 260 Watts S-Series 6x9" 2-Way Hi-Res Car Audio Coaxial Speakers General Features: 6" x 9" 2-way Coaxial Car Speakers Peak Power Handling: 520 watts per pair / 260 watts each RMS Power Handling: 170 watts per pair / 85 watts each Polypropylene cone material Rubber speaker surround High Amplitude Multi-Roll surround technology HI-RES Certified 1" Silk Dome Tweeters Large Ferrite magnet structure Top-mount Depth: 3" Cutout Dimensions: 5-29/32 x 8-3/4  Impedance: 4 ohms Frequency Response: 65 - 40000 Hz Sensitivity: 88 dB Authorized Internet Dealer MFR #: S2-S69 1-year Manufacturer's Warranty Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-S65C 6.5" Component Set & S2-S69 6x9" Coaxial Speaker & S2-A36F 4 Gauge Amplifier & Absolute KIT8 8 Gauge / 1000 Watt Complete Amplifier Hookup Installation Kit Bundle Alpine S2-A36F 600W Next Generation S-Series Hi Res Class-D 4-Channel Car Amplifier The next generation of Alpine S-Series amplifiers is designed to take your car audio experience to the next level without breaking the bank. With a sleek new redesign and upgraded features from their predecessors, these amplifiers offer exceptional performance and power on an affordable budget.The S-Series S2-A36F 4-channel amplifier delivers 60 Watts RMS @4 Ohms or 90 Watts RMS @2 Ohms of pristine high-fidelity signal to your car's front and rear speakers, adding sweet, clear sound to your vehicle. General Features: Hi-Res Audio Certified (Up to 40kHz) Power Rating: 14.4V, < 0.3% THD +N Power Output: 60W RMS x 4 @ 4Ω, 90W RMS x 4 @ 2Ω Bridged Power: 180W RMS x 2 @ 4Ω 4-Channel Amplifier Alpine’s Class D Amplifier Circuit Two-sided terminal layout Built-in Selectable/ Adjustable Crossovers Mid-Bass EQ Input for more power Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately) Dimensions: 8.7” W x 2.25” H x 8.25” D Weight: 4 lbs, 13 oz S/N Ratio: >83dB Frequency Response: 20Hz – 40kHz Damping Factor: >100 Owner’s Manual 4 Self-tapping screws Hexagon wrench Alpine S2-S65C 480W Peak (160W RMS) 6.5" S-Series 2-way Component Speaker System General Features: 6-1/2" 2-way Component System Car Speakers Peak Power Handling: 480 watts per set / 240 watts on each side RMS Power Handling: 160 watts per set / 80 watts on each side Polypropylene cone material Rubber speaker surround High Amplitude Multi-Roll surround technology HI-RES Certified 1" Silk Dome Tweeters Ferrite magnet motor structure Top-mount Depth: 2-5/16" Cutout Dimensions: 5-1/8" Impedance: 4 ohms Frequency Response: 55 - 40000 Hz Sensitivity: 88 dB Authorized Internet Dealer 1-year Manufacturer's Warranty Alpine S2-S69 260 Watts S-Series 6x9" 2-Way Hi-Res Car Audio Coaxial Speakers General Features: 6" x 9" 2-way Coaxial Car Speakers Peak Power Handling: 520 watts per pair / 260 watts each RMS Power Handling: 170 watts per pair / 85 watts each Polypropylene cone material Rubber speaker surround High Amplitude Multi-Roll surround technology HI-RES Certified 1" Silk Dome Tweeters Large Ferrite magnet structure Top-mount Depth: 3" Cutout Dimensions: 5-29/32 x 8-3/4  Impedance: 4 ohms Frequency Response: 65 - 40000 Hz Sensitivity: 88 dB Authorized Internet Dealer MFR #: S2-S69 1-year Manufacturer's Warranty Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-S65C 6.5" Component Set & S2-S69 6x9" Coaxial Speaker & S2-A36F 4 Gauge Amplifier & Absolute KIT10 10 Gauge / 800 Watt Complete Amplifier Hookup Installation Kit Bundle Alpine S2-A36F 600W Next Generation S-Series Hi Res Class-D 4-Channel Car Amplifier The next generation of Alpine S-Series amplifiers is designed to take your car audio experience to the next level without breaking the bank. With a sleek new redesign and upgraded features from their predecessors, these amplifiers offer exceptional performance and power on an affordable budget.The S-Series S2-A36F 4-channel amplifier delivers 60 Watts RMS @4 Ohms or 90 Watts RMS @2 Ohms of pristine high-fidelity signal to your car's front and rear speakers, adding sweet, clear sound to your vehicle. General Features: Hi-Res Audio Certified (Up to 40kHz) Power Rating: 14.4V, < 0.3% THD +N Power Output: 60W RMS x 4 @ 4Ω, 90W RMS x 4 @ 2Ω Bridged Power: 180W RMS x 2 @ 4Ω 4-Channel Amplifier Alpine’s Class D Amplifier Circuit Two-sided terminal layout Built-in Selectable/ Adjustable Crossovers Mid-Bass EQ Input for more power Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately) Dimensions: 8.7” W x 2.25” H x 8.25” D Weight: 4 lbs, 13 oz S/N Ratio: >83dB Frequency Response: 20Hz – 40kHz Damping Factor: >100 Owner’s Manual 4 Self-tapping screws Hexagon wrench Alpine S2-S65C 480W Peak (160W RMS) 6.5" S-Series 2-way Component Speaker System General Features: 6-1/2" 2-way Component System Car Speakers Peak Power Handling: 480 watts per set / 240 watts on each side RMS Power Handling: 160 watts per set / 80 watts on each side Polypropylene cone material Rubber speaker surround High Amplitude Multi-Roll surround technology HI-RES Certified 1" Silk Dome Tweeters Ferrite magnet motor structure Top-mount Depth: 2-5/16" Cutout Dimensions: 5-1/8" Impedance: 4 ohms Frequency Response: 55 - 40000 Hz Sensitivity: 88 dB Authorized Internet Dealer 1-year Manufacturer's Warranty Alpine S2-S69 260 Watts S-Series 6x9" 2-Way Hi-Res Car Audio Coaxial Speakers General Features: 6" x 9" 2-way Coaxial Car Speakers Peak Power Handling: 520 watts per pair / 260 watts each RMS Power Handling: 170 watts per pair / 85 watts each Polypropylene cone material Rubber speaker surround High Amplitude Multi-Roll surround technology HI-RES Certified 1" Silk Dome Tweeters Large Ferrite magnet structure Top-mount Depth: 3" Cutout Dimensions: 5-29/32 x 8-3/4  Impedance: 4 ohms Frequency Response: 65 - 40000 Hz Sensitivity: 88 dB Authorized Internet Dealer MFR #: S2-S69 1-year Manufacturer's Warranty Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-A36F 600W Class-D 4-Channel Car Amplifier & 2 Pair Alpine S2-S65 6.5" 480 Watts S-Series Hi-Res Certified 2Way Coaxial Car Speakers & Absolute KIT10 10 Gauge / 800 Watt Complete Amplifier Hookup Installation Kit Bundle Alpine S2-A36F 600W Next Generation S-Series Hi Res Class-D 4-Channel Car Amplifier The next generation of Alpine S-Series amplifiers is designed to take your car audio experience to the next level without breaking the bank. With a sleek new redesign and upgraded features from their predecessors, these amplifiers offer exceptional performance and power on an affordable budget.The S-Series S2-A36F 4-channel amplifier delivers 60 Watts RMS @4 Ohms or 90 Watts RMS @2 Ohms of pristine high-fidelity signal to your car's front and rear speakers, adding sweet, clear sound to your vehicle.The amp brings your music to life by being Hi-Res Audio certified, with its precise details and emotional power revealed with a frequency response up to 40kHz. For a 3-channel 2-way system, you could also use the amp to drive a pair of front speakers with 60 Watts RMS each while powering a subwoofer with 180 Watts RMS from the bridged rear channels. A variable mid-bass boost on those rear channels allows you to dial in some extra kick and impact to your system's low-frequency sound. You can even add the optional wired remote RUX-KNOB2 to control the level of the rear channels from your front seat.High- and low-pass filters put you in command of the frequency spectrum that reaches your speakers and subs. The amp includes preamp- and speaker-level inputs so you can install it in almost any vehicle, even with a factory radio. When using the speaker-level inputs, the amp can sense the incoming signal and turn itself on, eliminating the need to run a separate turn-on wire to the receiver or fuse box. General Features: Hi-Res Audio Certified (Up to 40kHz) Power Rating: 14.4V, < 0.3% THD +N Power Output: 60W RMS x 4 @ 4Ω, 90W RMS x 4 @ 2Ω Bridged Power: 180W RMS x 2 @ 4Ω 4-Channel Amplifier Alpine’s Class D Amplifier Circuit Two-sided terminal layout Built-in Selectable/ Adjustable Crossovers Mid-Bass EQ Input for more power Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately) Dimensions: 8.7” W x 2.25” H x 8.25” D Weight: 4 lbs, 13 oz S/N Ratio: >83dB Frequency Response: 20Hz – 40kHz Damping Factor: >100 Owner’s Manual 4 Self-tapping screws Hexagon wrench Alpine S2-S65 6.5" 480 Watts S-Series Hi-Res Certified 2Way Coaxial Car Speakers  Newly redesigned and Hi-Res Audio Certified, the Next-Generation S-Series S2-S65 6.5” Coaxial Speakers offer a new standard in entry-level sound performance. Using “trickle-down” technology, inspired design, and performance cues from the Ultra-High-Resolution AlpineF#1Status system, the Next-Generation Alpine S-Series Speakers are now Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This new benchmark in sound quality elevates the Next-Gen S-Series Speakers, resulting in a more accurate and natural sound at an entry-level price point. Crafted with a unique combination of Poly Propylene, Glass Fiber, and Mica Cone materials, the S2-S65 is designed for lightweight construction, high output, and low distortion, giving you a clean and accurate audio experience. General Features: 6-1/2" 2-way Coaxial Car Speakers Peak Power Handling: 480 watts per pair / 240 watts each Power Handling RMS: 160 watts per pair / 80 watts each Polypropylene cone material Rubber speaker surround High Amplitude Multi-Roll surround technology HI-RES Certified Optional Grills KTE-S65G available 1" Silk Dome Tweeters Ferrite magnet motor structure Top-mount Depth: 2-5/16" Cutout Dimensions: 5-1/8" Impedance: 4 ohms Frequency Response: 55 - 40000 Hz Sensitivity: 88 dB Authorized Internet Dealer MFR #: S2-S65 1-year Manufacturer's Warranty Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-A36F 600W Class-D 4-Channel Car Amplifier & 2 Pair Alpine S2-S65 6.5" 480 Watts S-Series Hi-Res Certified 2Way Coaxial Car Speakers Alpine S2-A36F 600W Next Generation S-Series Hi Res Class-D 4-Channel Car Amplifier The next generation of Alpine S-Series amplifiers is designed to take your car audio experience to the next level without breaking the bank. With a sleek new redesign and upgraded features from their predecessors, these amplifiers offer exceptional performance and power on an affordable budget.The S-Series S2-A36F 4-channel amplifier delivers 60 Watts RMS @4 Ohms or 90 Watts RMS @2 Ohms of pristine high-fidelity signal to your car's front and rear speakers, adding sweet, clear sound to your vehicle.The amp brings your music to life by being Hi-Res Audio certified, with its precise details and emotional power revealed with a frequency response up to 40kHz. For a 3-channel 2-way system, you could also use the amp to drive a pair of front speakers with 60 Watts RMS each while powering a subwoofer with 180 Watts RMS from the bridged rear channels. A variable mid-bass boost on those rear channels allows you to dial in some extra kick and impact to your system's low-frequency sound. You can even add the optional wired remote RUX-KNOB2 to control the level of the rear channels from your front seat.High- and low-pass filters put you in command of the frequency spectrum that reaches your speakers and subs. The amp includes preamp- and speaker-level inputs so you can install it in almost any vehicle, even with a factory radio. When using the speaker-level inputs, the amp can sense the incoming signal and turn itself on, eliminating the need to run a separate turn-on wire to the receiver or fuse box. General Features: Hi-Res Audio Certified (Up to 40kHz) Power Rating: 14.4V, < 0.3% THD +N Power Output: 60W RMS x 4 @ 4Ω, 90W RMS x 4 @ 2Ω Bridged Power: 180W RMS x 2 @ 4Ω 4-Channel Amplifier Alpine’s Class D Amplifier Circuit Two-sided terminal layout Built-in Selectable/ Adjustable Crossovers Mid-Bass EQ Input for more power Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately) Dimensions: 8.7” W x 2.25” H x 8.25” D Weight: 4 lbs, 13 oz S/N Ratio: >83dB Frequency Response: 20Hz – 40kHz Damping Factor: >100 Owner’s Manual 4 Self-tapping screws Hexagon wrench Alpine S2-S65 6.5" 480 Watts S-Series Hi-Res Certified 2Way Coaxial Car Speakers  Newly redesigned and Hi-Res Audio Certified, the Next-Generation S-Series S2-S65 6.5” Coaxial Speakers offer a new standard in entry-level sound performance. Using “trickle-down” technology, inspired design, and performance cues from the Ultra-High-Resolution AlpineF#1Status system, the Next-Generation Alpine S-Series Speakers are now Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This new benchmark in sound quality elevates the Next-Gen S-Series Speakers resulting in a more accurate and natural sound at an entry-level price point. Crafted with a unique combination of Poly Propylene, Glass Fiber, and Mica Cone materials, the S2-S65 is designed for lightweight construction, high output, and low distortion, giving you a clean and accurate audio experience. General Features: 6-1/2" 2-way Coaxial Car Speakers Peak Power Handling: 480 watts per pair / 240 watts each Power Handling RMS: 160 watts per pair / 80 watts each Polypropylene cone material Rubber speaker surround High Amplitude Multi-Roll surround technology HI-RES Certified Optional Grills KTE-S65G available 1" Silk Dome Tweeters Ferrite magnet motor structure Top-mount Depth: 2-5/16" Cutout Dimensions: 5-1/8" Impedance: 4 ohms Frequency Response: 55 - 40000 Hz Sensitivity: 88 dB Authorized Internet Dealer MFR #: S2-S65 1-year Manufacturer's Warranty Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-A36F 600W Class-D 4-Channel Car Amplifier & Alpine S2-S65 6.5" 480 Watts S-Series Hi-Res Certified 2Way Coaxial Car Speakers & Absolute KIT10 10 Gauge / 800 Watt Complete Amplifier Hookup Installation Kit Bundle Alpine S2-A36F 600W Next Generation S-Series Hi Res Class-D 4-Channel Car Amplifier The next generation of Alpine S-Series amplifiers is designed to take your car audio experience to the next level without breaking the bank. With a sleek new redesign and upgraded features from their predecessors, these amplifiers offer exceptional performance and power on an affordable budget.The S-Series S2-A36F 4-channel amplifier delivers 60 Watts RMS @4 Ohms or 90 Watts RMS @2 Ohms of pristine high-fidelity signal to your car's front and rear speakers, adding sweet, clear sound to your vehicle.The amp brings your music to life by being Hi-Res Audio certified, with its precise details and emotional power revealed with a frequency response up to 40kHz. For a 3-channel 2-way system, you could also use the amp to drive a pair of front speakers with 60 Watts RMS each while powering a subwoofer with 180 Watts RMS from the bridged rear channels. A variable mid-bass boost on those rear channels allows you to dial in some extra kick and impact to your system's low-frequency sound. You can even add the optional wired remote RUX-KNOB2 to control the level of the rear channels from your front seat.High- and low-pass filters put you in command of the frequency spectrum that reaches your speakers and subs. The amp includes preamp- and speaker-level inputs so you can install it in almost any vehicle, even with a factory radio. When using the speaker-level inputs, the amp can sense the incoming signal and turn itself on, eliminating the need to run a separate turn-on wire to the receiver or fuse box. General Features: Hi-Res Audio Certified (Up to 40kHz) Power Rating: 14.4V, < 0.3% THD +N Power Output: 60W RMS x 4 @ 4Ω, 90W RMS x 4 @ 2Ω Bridged Power: 180W RMS x 2 @ 4Ω 4-Channel Amplifier Alpine’s Class D Amplifier Circuit Two-sided terminal layout Built-in Selectable/ Adjustable Crossovers Mid-Bass EQ Input for more power Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately) Dimensions: 8.7” W x 2.25” H x 8.25” D Weight: 4 lbs, 13 oz S/N Ratio: >83dB Frequency Response: 20Hz – 40kHz Damping Factor: >100 Owner’s Manual 4 Self-tapping screws Hexagon wrench Alpine S2-S65 6.5" 480 Watts S-Series Hi-Res Certified 2Way Coaxial Car Speakers  Newly redesigned and Hi-Res Audio Certified, the Next-Generation S-Series S2-S65 6.5” Coaxial Speakers offer a new standard in entry-level sound performance. Using “trickle-down” technology, inspired design, and performance cues from the Ultra-High-Resolution AlpineF#1Status system, the Next-Generation Alpine S-Series Speakers are now Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This new benchmark in sound quality elevates the Next-Gen S-Series Speakers resulting in a more accurate and natural sound at an entry-level price point. Crafted with a unique combination of Poly Propylene, Glass Fiber, and Mica Cone materials, the S2-S65 is designed for lightweight construction, high output, and low distortion, giving you a clean and accurate audio experience. General Features: 6-1/2" 2-way Coaxial Car Speakers Peak Power Handling: 480 watts per pair / 240 watts each Power Handling RMS: 160 watts per pair / 80 watts each Polypropylene cone material Rubber speaker surround High Amplitude Multi-Roll surround technology HI-RES Certified Optional Grills KTE-S65G available 1" Silk Dome Tweeters Ferrite magnet motor structure Top-mount Depth: 2-5/16" Cutout Dimensions: 5-1/8" Impedance: 4 ohms Frequency Response: 55 - 40000 Hz Sensitivity: 88 dB Authorized Internet Dealer MFR #: S2-S65 1-year Manufacturer's Warranty Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-A36F 600W Class-D 4-Channel Car Amplifier & Alpine S2-S65 6.5" 480 Watts S-Series Hi-Res Certified 2Way Coaxial Car Speakers Alpine S2-A36F 600W Next Generation S-Series Hi Res Class-D 4-Channel Car Amplifier The next generation of Alpine S-Series amplifiers is designed to take your car audio experience to the next level without breaking the bank. With a sleek new redesign and upgraded features from their predecessors, these amplifiers offer exceptional performance and power on an affordable budget.The S-Series S2-A36F 4-channel amplifier delivers 60 Watts RMS @4 Ohms or 90 Watts RMS @2 Ohms of pristine high-fidelity signal to your car's front and rear speakers, adding sweet, clear sound to your vehicle.The amp brings your music to life by being Hi-Res Audio certified, with its precise details and emotional power revealed with a frequency response up to 40kHz. For a 3-channel 2-way system, you could also use the amp to drive a pair of front speakers with 60 Watts RMS each while powering a subwoofer with 180 Watts RMS from the bridged rear channels. A variable mid-bass boost on those rear channels allows you to dial in some extra kick and impact to your system's low-frequency sound. You can even add the optional wired remote RUX-KNOB2 to control the level of the rear channels from your front seat.High- and low-pass filters put you in command of the frequency spectrum that reaches your speakers and subs. The amp includes preamp- and speaker-level inputs so you can install it in almost any vehicle, even with a factory radio. When using the speaker-level inputs, the amp can sense the incoming signal and turn itself on, eliminating the need to run a separate turn-on wire to the receiver or fuse box. General Features: Hi-Res Audio Certified (Up to 40kHz) Power Rating: 14.4V, < 0.3% THD +N Power Output: 60W RMS x 4 @ 4Ω, 90W RMS x 4 @ 2Ω Bridged Power: 180W RMS x 2 @ 4Ω 4-Channel Amplifier Alpine’s Class D Amplifier Circuit Two-sided terminal layout Built-in Selectable/ Adjustable Crossovers Mid-Bass EQ Input for more power Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately) Dimensions: 8.7” W x 2.25” H x 8.25” D Weight: 4 lbs, 13 oz S/N Ratio: >83dB Frequency Response: 20Hz – 40kHz Damping Factor: >100 Owner’s Manual 4 Self-tapping screws Hexagon wrench Alpine S2-S65 6.5" 480 Watts S-Series Hi-Res Certified 2Way Coaxial Car Speakers  Newly redesigned and Hi-Res Audio Certified, the Next-Generation S-Series S2-S65 6.5” Coaxial Speakers offer a new standard in entry-level sound performance. Using “trickle-down” technology, inspired design, and performance cues from the Ultra-High-Resolution AlpineF#1Status system, the Next-Generation Alpine S-Series Speakers are now Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This new benchmark in sound quality elevates the Next-Gen S-Series Speakers resulting in a more accurate and natural sound at an entry-level price point. Crafted with a unique combination of Poly Propylene, Glass Fiber, and Mica Cone materials, the S2-S65 is designed for lightweight construction, high output, and low distortion, giving you a clean and accurate audio experience. General Features: 6-1/2" 2-way Coaxial Car Speakers Peak Power Handling: 480 watts per pair / 240 watts each Power Handling RMS: 160 watts per pair / 80 watts each Polypropylene cone material Rubber speaker surround High Amplitude Multi-Roll surround technology HI-RES Certified Optional Grills KTE-S65G available 1" Silk Dome Tweeters Ferrite magnet motor structure Top-mount Depth: 2-5/16" Cutout Dimensions: 5-1/8" Impedance: 4 ohms Frequency Response: 55 - 40000 Hz Sensitivity: 88 dB Authorized Internet Dealer MFR #: S2-S65 1-year Manufacturer's Warranty Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.