Alpine (1173)

2 Pair Alpine S-Series S2-S40 4" 140 Watts 2-Way Hi-Res Car Audio Coaxial Speakers Newly redesigned and Hi-Res Audio Certified, the Next-Generation S-Series S2-S40 4” Coaxial Speakers offer a new standard in entry-level sound performance. We packed supreme capability into these speakers using highly effective materials and proprietary design elements. The lightweight woofer cone, crafted from a combination of polypropylene, glass fiber, and mica materials, serves up the essential high output / low distortion sound required for High-Res Audio performance. Alpine S-Series speakers feature increased magnet sizes for more power handling and the best mid-bass performance in their category. General Features: 4" 2-way Coaxial Car Speakers Peak Power Handling: 280 watts per pair / 140 watts each RMS Peak Power: 90 watts per pair / 45 watts each Polypropylene cone material Rubber speaker surround High Amplitude Multi-Roll (HAMR) surround HI-RES Certified 3/4" Silk Dome Tweeters Ferrite magnet motor structure Top-mount Depth: 1-3/4" Cutout Dimensions: 3-11/16" Impedance: 4 ohms Frequency Response: 90 - 40000 Hz Sensitivity: 86 dB Authorized Internet Dealer 1-year Manufacturer's Warranty Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

2 Alpine S-W10D2 1800W Max (600W RMS) 10" S-Series Dual 2 Ohm Car Subwoofer  with Absolute TW500 Tweeter & Absolute BT1700 Electrical Tape & Mobile Magnet Holder Alpine introduces the all-new S-Series Subwoofers. Their unique design substantially improves bass output and provides installation versatility. Each S-Series subwoofer uses a custom-stamped steel frame and is available in twelve, ten, and eight-inch sizes. These high-strength frames were designed to withstand the rigors of the improved S-Series motor. They have frame leg vents, a vented back plate to help cool the subwoofer voice coil and motor parts, and a shallow design to help fit in smaller spaces. The S-Series Subwoofers incorporates two strontium ferrite magnets stacked together, providing increased motor strength and excursion and ultimately delivering accurate bass to your music. The convenient push-type insert terminals with a dual voice coil jumper system will significantly reduce installation time. Just strip the speaker insulation at the wire end, then insert the bare wire into the hole of the spring-loaded push terminal. At the same time, the concealed mount gasket system creates a clean, finished appearance for any vehicle. General Features: 10" 2 ohm S-Series (Type-S) Subwoofer RMS Power Handling: 600 watts Peak Power Handling: 1800 watts  Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 4-11/16" Cutout diameter: 8-13/16 Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 33 Hz Authorized Dealer 1-year Manufacturer's Warranty What is in the S-W10D2 package: S-W10D2 owner's manual One 10" Dual 2-ohm voice coil subwoofer 1 Rubber concealing ring Two 3" jumper cables (each has a single banana connector on each end) Subwoofer Application Guide Online product registration information Warranty Information Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

2 Alpine S-W10D2 1800W Max (600W RMS) 10" S-Series Dual 2 Ohm Car Subwoofer   Alpine introduces the all-new S-Series Subwoofers; their unique design substantially improves bass output and provides installation versatility. Each S-Series subwoofer uses a custom-stamped steel frame and is available in twelve, ten, and eight-inch. These high-strength frames were designed to withstand the rigors of the improved S-Series motor. They have frame leg vents, a vented back plate to help cool the subwoofer voice coil and motor parts, and a shallow design to help fit in smaller spaces. The S-Series Subwoofers incorporate two strontium ferrite magnets stacked together, providing increased motor strength and excursion, ultimately delivering an accurate bass to your music. The convenient push-type insert terminals with a dual voice coil jumper system will significantly reduce installation time. Just strip the speaker insulation at the wire end, then insert the bare wire into the hole of the spring-loaded push terminal. At the same time, the concealed mount gasket system creates a clean, finished appearance for any vehicle. General Features: 10" 2 ohm S-Series (Type-S) Subwoofer RMS Power Handling: 600 watts Peak Power Handling: 1800 watts  Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 4-11/16" Cutout diameter: 8-13/16 Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 33 Hz Authorized Dealer 1-year Manufacturer's Warranty What is in the S-W10D2 package: S-W10D2 owner's manual One 10" Dual 2-ohm voice coil subwoofer 1 Rubber concealing ring Two 3" jumper cables (each has a single banana connector on each end) Subwoofer Application Guide Online product registration information Warranty Information ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

2 Alpine S-W10D2 1800W Max (600W RMS) 10" S-Series Dual 2 Ohm Car Subwoofer Alpine introduces the all-new S-Series Subwoofers; their unique design substantially improves bass output and provides installation versatility. Each S-Series subwoofer uses a custom-stamped steel frame and is available in twelve, ten, and eight-inch. These high-strength frames were designed to withstand the rigors of the improved S-Series motor. They have frame leg vents, a vented back plate to help cool the subwoofer voice coil and motor parts, and a shallow design to help fit in smaller spaces. The S-Series Subwoofers incorporates two strontium ferrite magnets stacked together, providing increased motor strength and excursion, ultimately delivering an accurate bass to your music. The convenient push-type insert terminals with a dual voice coil jumper system will significantly reduce installation time. Just strip the speaker insulation at the wire end, then insert the bare wire into the hole of the spring-loaded push terminal. At the same time, the concealed mount gasket system creates a clean, finished appearance for any vehicle. General Features: 10" 2 ohm S-Series (Type-S) Subwoofer RMS Power Handling: 600 watts Peak Power Handling: 1800 watts  Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 4-11/16" Cutout diameter: 8-13/16 Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 33 Hz Authorized Dealer 1-year Manufacturer's Warranty What is in the S-W10D2 package: S-W10D2 owner's manual One 10" Dual 2-ohm voice coil subwoofer 1 Rubber concealing ring Two 3" jumper cables (each has a single banana connector on each end) Subwoofer Application Guide Online product registration information Warranty Information ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

2 Alpine S-W10D4 1800W Max (600W RMS) 10" S-Series Dual 4 Ohm Car Subwoofer Alpine introduces the all-new S-Series Subwoofers; their unique design substantially improves bass output and provides installation versatility. Each S-Series subwoofer uses a custom-stamped steel frame and is available in twelve, ten, and eight-inch. These high-strength frames were designed to withstand the rigors of the improved S-Series motor. They have frame leg vents, a vented back plate to help cool the subwoofer voice coil and motor parts, and a shallow design to help fit in smaller spaces. The S-Series Subwoofers incorporate two strontium ferrite magnets stacked together, providing increased motor strength and excursion, ultimately delivering an accurate bass to your music. The convenient push-type insert terminals with a dual voice coil jumper system will significantly reduce installation time. Just strip the speaker insulation at the wire end, then insert the bare wire into the hole of the spring-loaded push terminal. At the same time, the concealed mount gasket system creates a clean, finished appearance for any vehicle. General Features: 10" 4 ohm S-Series (Type-S) Subwoofer RMS Power Handling: 600 watts Peak Power Handling: 1800 watts  Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 4-11/16" Cutout diameter: 8-13/16 Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 33 Hz Authorized Dealer 1-year Manufacturer's Warranty What's in the S-W10D4 package: S-W10D4 owner's manual One 10" Dual 4-ohm voice coil subwoofer Two 3" jumper cables Subwoofer Application Guide Online product registration information Warranty information ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

2 Alpine S-W10D4 1800W Max (600W RMS) 10" S-Series Dual 4 Ohm Car Subwoofer with Absolute TW500 Tweeter & BT1700 Electrical Tape & Mobile Holder VERSATILE APPLICATIONS Along with the new 8” woofer, the 10” and 12” S-Series subwoofers have been re-designed from the ground up. The mounting depth of the 10” and 12” subwoofers are almost 1” more shallow than previous models at just over 4.5” for the 10” models and just over 5” for the 12” models, allowing them to fit into a wide variety of installation applications. General Features: 10" 4 ohm S-Series (Type-S) Subwoofer Power Handling: Peak: 1800 watts RMS: 600 watts Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 4-11/16" Cutout diameter: 8-13/16 Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 33 Hz Authorized Dealer 1-year Manufacturer's Warranty What's in the S-W10D4 package: One 10" Dual 4-ohm voice coil subwoofer Two 3" jumper cables (each has a single banana connector on each end) Subwoofer Application Guide Online product registration information Warranty information S-W10D4 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

  2 Alpine S-W12D2 1800W Max (600W RMS) 12" Type-S Series Dual 2 ohm Car Subwoofer VERSATILE APPLICATIONS Along with the new 8” woofer, the 10” and 12” S-Series subwoofers have been re-designed from the ground up. The mounting depth of the 10” and 12” subwoofers are almost 1” more shallow than previous models at just over 4.5” for the 10” models and just over 5” for the 12” models, allowing them to fit into a wide variety of installation applications. General Features: 12" 2 Ohm Type-S Series Subwoofer Power Handling: Peak: 1800 watts RMS: 600 watts Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 5-1/16" Cutout diameter: 10-9" Frequency Response: 26- 200Hz Sensitivity: 86.2dB Resonance Frequency (Fs): 31 Hz Authorized Dealer 1-year Manufacturer's Warranty What's in the box: Two 12" Dual 2-ohm voice coil subwoofer 1 Rubber concealing ring (installed) Two 3" jumper cables (each has a single banana connector on each end) Subwoofer Application Guide (English/ French) Online product registration information (English/ French/ Spanish) Warranty information (English/ French) Important Notice! (English/ French) Alpine S-W12D2 owners manual

2 Alpine S-W12D4 1800W Max (600W RMS) 12" Type-S Series Dual 4 Ohm Car Subwoofer VERSATILE APPLICATIONS Along with the new 8” woofer, the 10” and 12” S-Series subwoofers have been re-designed from the ground up. The mounting depth of the 10” and 12” subwoofers are almost 1” more shallow than previous models at just over 4.5” for the 10” models and just over 5” for the 12” models, allowing them to fit into a wide variety of installation applications. General Features: 12" 4 Ohm Type-S Series Subwoofer Power Handling: Peak: 1800 watts RMS: 600 watts Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 5-1/16" Cutout diameter: 10-9" Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 31 Hz Authorized Dealer 1-year Manufacturer's Warranty What is in the S-W12D4 package: Alpine S-W12D4 owners manual One 12" Dual 4-ohm voice coil subwoofer Two 3" jumper cables Subwoofer Application Guide Online product registration information Warranty Information ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

2 Alpine S-W8D2 900W Max (300W RMS) 8" S-Series Dual 2 Ohm Car Subwoofers ADD BASS TO PRACTICALLY ANY VEHICLE Don’t think you have room for a subwoofer? Think again. The new S-W8D2 and S-W8D2 8” S-Series subwoofers have a shallow mounting depth of just 3-3/4” and can be used in a sealed box enclosure as small as .15 cubic feet. It is perfect for under seats, behind rear bench seats in trucks, or even in some door applications. General Features: 8" 2 Ohm S-Series Subwoofer Power Handling: Peak: 900 watts RMS: 300 watts Recommended power range: 150 - 300 RMS Kevlar Reinforced Pulp Cone HAMR Santoprene Rubber Surround High Strength Steel Frame Basket Concealed Mount Gasket High Strength Steel Frame Basket 10 AWG Push Terminals High Excursion Underhung Voice Coil Configuration High-Grade Strontium Ferrite Magnet Top-mount depth: 3-3/4" Cutout diameter: 6-7/8" Frequency Response: 34 - 200 Hz Sensitivity: 83dB Resonance Frequency (Fs): 48 Hz Authorized Dealer 1-year Manufacturer's Warranty What's in the box: Two 8" Dual 2-ohm voice coil subwoofer 1 Rubber concealing ring (installed) Two 3" jumper cables (each has a single banana connector on each end) Subwoofer Application Guide (English/ French) Online product registration information (English/ French/ Spanish) Warranty information (English/ French) Important Notice! (English/ French) Alpine S-W8D2 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

2 Alpine S2-S65 6.5" 480 Watt Car Audio Speakers+BBX-T600 2 Channel Amplifier + Absolute KIT4 4G Amp Kit Alpine BBX-T600 600W Max BBX Series 2-ohm Stable 2 Channel Class A/B Amplifier This new BBX amplifier gives you Alpine power performance at an amazing price. And they are designed to fit easily in virtually any system. This amp delivers high output power and exceptional performance for their class. A great way to expand your sound system on a limited budget. These two filters let you set the frequency points for the high, mid, and bass ranges to match your speakers and ensure optimum efficiency. With Bass EQ, you can maximize the performance of your system and get even more powerful bass. General Features: Alpine BBX-T600 Class-A/B 2-ohm Stable 2-Channel Amplifier 50 Watts @ 4 Ohm x 2 Channel 70 Watts @ 2 Ohm x 2 Channel 130 Watts @ 4 Ohm x 1 Channel Bridged Total power output: 600 watts Pulse Width Modulated MOSFET power supply LED power (green) and protect (red) indicators Soft start turn-on Two or Mono channel operation One pair of preamp outputs to connect multiple amplifiers 3-way protection circuitry (thermal, overload, and speaker short protection) Dual speaker terminals simplify the hookup of multiple speakers Heavy-duty aluminum alloy heat-sink Input sensitivity: .2V - 8V Frequency Response: 5 - 50000 Hz Total Harmonic Distortion (THD): <1% Signal Noise Ratio: 95dB Variable high-pass filter: 80 - 1200 Hz Variable low-pass filter: 50 - 500 Hz Variable Bass Boost: 0 to +12 dB bass boost Fuse Rating: 20A x 1 Dimensions: 9.84"W x 9.44"L x 2"H Authorized Internet Dealer 1-year Manufacturer's Warranty Weight: 5.00lbs What's in the BBX-T600 package: BBX-T600 owner's manual Two Channel amplifier Owner's manual (English/ French/ Spanish) Alpine Verification Certificate Warranty information Power supply note Online product registration information Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

2 Pair Alpine S2-S65 6.5" 480 Watts S-Series Hi-Res Certified 2Way Coaxial Car Speakers & Absolute KIT10 10 Gauge / 800 Watt Complete Amplifier Hookup Installation Kit Bundle 2 Alpine S2-S65 6.5" 480 Watts S-Series Hi-Res Certified 2 Way Coaxial Car Speakers Newly redesigned and Hi-Res Audio Certified, the Next-Generation S-Series S2-S65 6.5” Coaxial Speakers offer a new standard in entry-level sound performance. Using “trickle-down” technology, inspired design, and performance cues from the Ultra-High-Resolution AlpineF#1Status system, the Next-Generation Alpine S-Series Speakers are now Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This new benchmark in sound quality elevates the Next-Gen S-Series Speakers, resulting in a more accurate and natural sound at an entry-level price point. Crafted with a unique combination of polyphylene, Glass Fiber, and Mica Cone materials, the S2-S65 is designed for lightweight construction, high output, and low distortion, giving you a clean and accurate audio experience. General Features: 6-1/2" 2-way Coaxial Car Speakers Peak Power Handling: 480 watts per pair / 240 watts each Power Handling RMS: 160 watts per pair / 80 watts each Polypropylene cone material Rubber speaker surround High Amplitude Multi-Roll surround technology HI-RES Certified Optional Grills KTE-S65G available 1" Silk Dome Tweeters Ferrite magnet motor structure Top-mount Depth: 2-5/16" Cutout Dimensions: 5-1/8" Impedance: 4 ohms Frequency Response: 55 - 40000 Hz Sensitivity: 88 dB Authorized Internet Dealer Weight: ‎6.4 pounds Dimensions, ‎16.5 x 8.5 x 5 inches MFR #: S2-S65 1-year Manufacturer's Warranty What's in the S2-S65 package: Alpine S2-S65 owner's manual Two 2-way speakers 2 Adapter rings Two 12" Lengths of speaker wire  Eight 1-1/8" Screws Eight M4x6.5mm  Eight M4 Nuts 6 Flat washers 8 Speed clips Warranty information Online product registration information Important Notice sheet Declaration of conformity Template and specs on box Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

2 Alpine S2-S65 6.5" 480 Watts S-Series Hi-Res Certified 2 Way Coaxial Car Speakers Newly redesigned and Hi-Res Audio Certified, the Next-Generation S-Series S2-S65 6.5” Coaxial Speakers offer a new standard in entry-level sound performance. Using “trickle-down” technology, inspired design, and performance cues from the Ultra-High-Resolution AlpineF#1Status system, the Next-Generation Alpine S-Series Speakers are now Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This new benchmark in sound quality elevates the Next-Gen S-Series Speakers, resulting in a more accurate and natural sound at an entry-level price point. Crafted with a unique combination of polyphylene, Glass Fiber, and Mica Cone materials, the S2-S65 is designed for lightweight construction, high output, and low distortion, giving you a clean and accurate audio experience. General Features: 6-1/2" 2-way Coaxial Car Speakers Peak Power Handling: 480 watts per pair / 240 watts each Power Handling RMS: 160 watts per pair / 80 watts each Polypropylene cone material Rubber speaker surround High Amplitude Multi-Roll surround technology HI-RES Certified Optional Grills KTE-S65G available 1" Silk Dome Tweeters Ferrite magnet motor structure Top-mount Depth: 2-5/16" Cutout Dimensions: 5-1/8" Impedance: 4 ohms Frequency Response: 55 - 40000 Hz Sensitivity: 88 dB Authorized Internet Dealer Weight: ‎6.4 pounds Dimensions, ‎16.5 x 8.5 x 5 inches MFR #: S2-S65 1-year Manufacturer's Warranty What's in the S2-S65 package: Alpine S2-S65 owner's manual Two 2-way speakers 2 Adapter rings Two 12" Lengths of speaker wire  Eight 1-1/8" Screws Eight M4x6.5mm  Eight M4 Nuts 6 Flat washers 8 Speed clips Warranty information Online product registration information Important Notice sheet Declaration of conformity Template and specs on box Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.