audiocontrol (76)

AudioControl LC2i PRO 2-channel line output converter with AccuBASS™ High-level input line output converter More and more aftermarket amplifier installations depend on using the factory amp's powered outputs for its inputs. AudioControl's LC2i PRO line output converter takes amplified speaker-level signals and converts them into high-quality preamp signals that can then be fed to another processor, a full-range amplifier, or your subwoofer amp. Bass feature Some factory radios dial down the bass as you turn up the volume to protect the flimsy factory speakers. The problem is, they don't give it back when you upgrade to a nice set of aftermarket speakers. AudioControl packs the LC2i PRO with their AccuBASS™ circuitry that reverses the factory low-frequency roll-off, giving you the bass you need to enjoy your music to the fullest. Installation conveniences The included dash-mount wired remote control allows you to adjust the level of your sub channel on the go. Load selection switches make OEM integration easier, so the LC2i PRO will work with almost any factory sound system. Selectable turn-on modes include GTO™ Signal Sense (DC offset), audio sense, or remote 12 volt inputs. Product highlights: 2-channel active line output converter ACR-1 wired remote bass level control included 2 speaker-level inputs with 40-volt (400 watts RMS) power handling Main and Bass preamp-level outputs (up to 9.5 volts) Main and Bass output controls for level matching adjustable AccuBASS corrects for factory bass roll-off More Info: selectable turn-on options: GTO signal Sense (DC offset), audio sense, or remote 12 volt input 12-volt turn-on lead output recommended fuse rating: 1 amp dimensions: 6-15/16"W x 1"H x 3"D weight: 0.75 pound warranty: 5 years Two-Channel line output converter Two 4-pin captive-screw connectors (installed) ACR-1 Level control 16.5' Level-control cable (RJ-14) Quickstart guide (on cardboard label) ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

AudioControl LC2i PRO 2-channel line output converter+ Free Absolute Electrical Tape+ Phone Holderr High-level input line output converter More and more aftermarket amplifier installations depend on using the factory amp's powered outputs for its inputs. AudioControl's LC2i PRO line output converter takes amplified speaker-level signals and converts them into high-quality preamp signals that can then be fed to another processor, a full-range amplifier, or your subwoofer amp. Bass feature Some factory radios dial down the bass as you turn up the volume to protect the flimsy factory speakers. The problem is, they don't give it back when you upgrade to a nice set of aftermarket speakers. AudioControl packs the LC2i PRO with their AccuBASS™ circuitry that reverses the factory low-frequency roll-off, giving you the bass you need to enjoy your music to the fullest. Installation conveniences The included dash-mount wired remote control allows you to adjust the level of your sub channel on the go. Load selection switches make OEM integration easier, so the LC2i PRO will work with almost any factory sound system. Selectable turn-on modes include GTO™ Signal Sense (DC offset), audio sense, or remote 12 volt inputs. Product highlights: 2-channel active line output converter ACR-1 wired remote bass level control included 2 speaker-level inputs with 40-volt (400 watts RMS) power handling Main and Bass preamp-level outputs (up to 9.5 volts) Main and Bass output controls for level matching adjustable AccuBASS corrects for factory bass roll-off More Info: selectable turn-on options: GTO signal Sense (DC offset), audio sense, or remote 12 volt input 12-volt turn-on lead output recommended fuse rating: 1 amp dimensions: 6-15/16"W x 1"H x 3"D weight: 0.75 pound warranty: 5 years Two-Channel line output converter Two 4-pin captive-screw connectors (installed) ACR-1 Level control 16.5' Level-control cable (RJ-14) Quickstart guide (on cardboard label) Absolute BT1700 Vinyl Electrical Tape is good quality, multi-purpose vinyl insulating tape. It has great resistance to moisture and varying weather conditions. It is a polyvinyl chloride (PVC) tape that is flame-retardant and conformable. Details Resists abrasion, moisture, alkalis, solvents, and acids Flame-retardant and inhibits the corrosion of electrical conductors Made of durable PVC Compatible with rubber and synthetic splicing compounds Withstands a temperature range of 32 to 194 °F (0 to 90 °C) UL Listed, CSA and VDE Certified Specifications Adhesive Type Rubber Application Insulation Brand Absolute Elongation at Break 200 % Maximum Operating Temperature (Celsius) 90 Degree Celsius Maximum Operating Temperature (Fahrenheit) 194 Degree Fahrenheit Minimum Operating Temperature (Fahrenheit) 32 Degree Fahrenheit Overall Length (Imperial) 60 ft Overall Length (Metric) 18 m Overall Width (Imperial) 0.75 in Overall Width (Metric) 19 mm Product Color Black Shelf Life 5 Year Tape Grade General Use ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Audio Control LC6i 6 Channel Line Out Converter with Internal Summing for adding aftermarket amps to a factory system & ACR-1 Dash Remote AudioControl continues to simplify OEM integration with the new LC6i Six Channel Line Output Converter with internal summing. The LC6i is built on the same technology as its predecessor, the LC6. The LC6i converts speaker-level inputs from a factory radio or factory amplifier into high-quality pre-amp signals. The addition of internal summing capabilities and improved GTO™ signal-sense turn-on make the LC6i the perfect way to solve your OEM headaches. The LC6i allows for the addition of aftermarket processors and amplifiers while maintaining the use of the factory volume and steering wheel controls. Internal signal summing and AudioControl’s new GTO™ signal-sense turn-on make the LC6i a perfect OEM interface for a performance audio system. The LC6i follows in the steps of the rampantly successful LC8 Eight Channel Line Output Converter, offering all the same features for 6 channel systems at a reduced price. The LC6i accepts speaker level signals, both crossed-over, and full range, and converts them to high-quality pre-amp signals. Signals from factory radios with built-in crossovers can be overcome by summing them together, internally, to provide a full-range preamp signal. The LC6i provides the type of clean pre-amp signals installers are familiar with. Those who desire custom control over the sound can easily add one of AudioControl’s many crossovers or equalizers which offer unlimited system design flexibility, clearly different than traditional OEM interfaces. General Features: Six Input and Output Channels 6 Speaker Level Inputs - Can Accept 400-Watt Signals! Signal sensing inputs Internal Channel Summing AutoMode inputs Level matching controls 12-volt trigger output Line Output Converter: A device for converting a powered (or amplified) signal into a pre-amp line level (or non-powered) signal Input for optional subwoofer level control: AudioControl ACR-1 Color: Black Weight: 3.5 lbs Size: 8.00" W x 6.00" D x 1.20" H Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) LC6i Specifications: Maximum speaker-level input: 400 watts @ 4 ohms Maximum output level: 9.5Vrms Output gain: +/-12 dB Frequency response: 10Hz-22kHz Total harmonic distortion: 0.01% Input Impedance: 20K Ohms Power supply: High headroom PWM switching Power draw: 200mA Recommended fuse rating: 1 Amp Remote Trigger Output Current: 1 Amp What is in the LC6i package: 6-Channel line-output converter Instructions/Specs/Warranty (on packaging) Quality Control Certificate LC6i owner's manual AudioControl Remote ACR-1 Dash Mount Wired Remote Level Control for Select AudioControl Sound Processors General Features Wired Remote Level Control Mounts on the dash using built-in bracket Detachable mounting plate Works with select AudioControl sound processors Direct replacement remote for the Epicenter Includes 20' power cable Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) What is in the ACR-1 package: Remote dash mount control 20' RJ-14 cable. Mounting Instructions on packaging ACR-1 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Audio Control LC6i 6 Channel Line Out Converter with Internal Summing for add aftermarket amps to a factory system & ACR-1 Dash Remote AudioControl continues to simplify OEM integration with the new LC6i Six Channel Line Output Converter with internal summing. The LC6i is built on the same technology as its predecessor, the LC6. The LC6i converts speaker-level inputs from a factory radio or factory amplifier into high-quality pre-amp signals. The addition of internal summing capabilities and improved GTO™ signal-sense turn-on make the LC6i the perfect way to solve your OEM headaches. The LC6i allows for the addition of aftermarket processors and amplifiers while maintaining the use of the factory volume and steering wheel controls. Internal signal summing and AudioControl’s new GTO™ signal-sense turn-on make the LC6i a perfect OEM interface for a performance audio system. The LC6i follows in the steps of the rampantly successful LC8 Eight Channel Line Output Converter, offering all the same features for 6 channel systems at a reduced price. The LC6i accepts speaker level signals, both crossed-over, and full range, and converts them to high-quality pre-amp signals. Signals from factory radios with built-in crossovers can be overcome by summing them together, internally, to provide a full-range preamp signal. The LC6i provides the type of clean pre-amp signals installers are familiar with. Those who desire custom control over the sound can easily add one of AudioControl’s many crossovers or equalizers which offer unlimited system design flexibility, clearly different than traditional OEM interfaces. Add remote level control for your AudioControl processor or amplifier. This is the replacement remote for the Epicenter. Comes with a 20-foot cable and removable mounting enclosure (for custom dash installations).s. General Features: Six Input and Output Channels 6 Speaker Level Inputs - Can Accept 400-Watt Signals! Signal sensing inputs Internal Channel Summing AutoMode inputs Level matching controls 12-volt trigger output Line Output Converter: A device for converting a powered (or amplified) signal into a pre-amp line level (or non-powered) signal Input for optional subwoofer level control: AudioControl ACR-1 Color: Black Weight: 3.5 lbs Size: 8.00" W x 6.00" D x 1.20" H Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) LC6i Specifications: Maximum speaker-level input: 400 watts @ 4 ohms Maximum output level: 9.5Vrms Output gain: +/-12 dB Frequency response: 10Hz-22kHz Total harmonic distortion: 0.01% Input Impedance: 20K Ohms Power supply: High headroom PWM switching Power draw: 200mA Recommended fuse rating: 1 Amp Remote Trigger Output Current: 1 Amp What is in the LC6i box: 6-Channel line-output converter Instructions/Specs/Warranty (on packaging) Quality Control Certificate AudioControl LC6i owner's manual AudioControl Remote ACR-1 Dash Mount Wired Remote Level Control for Select AudioControl Sound Processors Add remote level control for your AudioControl processor or amplifier. This is the replacement remote for the Epicenter. Comes with a 20-foot cable and removable mounting enclosure (for custom dash installations).s. General Features Wired Remote Level Control Mounts on dash using built-in bracket Detachable mounting plate Works with select AudioControl sound processors Direct replacement remote for the Epicenter Includes 20' power cable Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) compatible with 6XS ACM-1.300 The Epicenter® Concert Series LC2i LC6i LC7i Overdrive Plus Matrix Plus LC-4.800 LC-6.1200 legacy products supported LC6 LC8 Original Epicenter® (bypass not supported) What is in the ACR-1 box: Remote dash mount control 20' RJ-14 cable. Mounting Instructions on packaging AudioControl ACR-1 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Audio Control LC7i 6 Channel Line Out Converter with bass restoration adds aftermarket subs and amps to a factory system & ACR-1 Dash Remote The AudioControl LC7i, six channel active line converter, allows all music lovers, who want a great in-car audio experience, to keep their factory-installed source unit and dramatically improve their system performance. The LC7i delivers amazing sound quality and fixes one of the biggest letdowns of today’s factory systems, weak BASS! Designed for maximum sound quality and enhanced audio performance, the LC7i incorporates AccuBASS™. This patented process automatically corrects for the bass roll-off that is common with many factory-installed audio systems and AudioControl’s unique and exclusive AccuBASS™ circuitry maintains and restores the Bass as the volume is turned up, improving the audio performance. The LC7i allows the flexibility of powering the audio signals downstream to single or multiple factory amps maximizing sound quality & achieving high output at a great price. In addition, the LC7i is designed to fit into a compact chassis allowing an easy & flexible factory system upgrade in today’s space constrained vehicles. The ACR-1 dash remote (sold separately) allows the user to control the level of the low-frequency output. Add remote level control for your AudioControl processor or amplifier. This is the replacement remote for the Epicenter. Comes with a 20-foot cable and removable mounting enclosure (for custom dash installations).s. General Features: Six Input and Output Channels 6 Speaker Level Inputs - Can Accept 400-Watt Signals! Signal sensing inputs GTO (Great Turn-On) Circuit Internal Channel Summing AutoMode inputs Level matching controls 12-volt trigger output Line Output Converter: A device for converting a powered (or amplified) signal into a pre-amp line level (or non-powered) signal Input for optional subwoofer level control: AudioControl ACR-1 Color: Black Weight: 3.0 lbs Size: 7.5" W x 4.72" D x 1.22" H Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) LC7i Specifications: Maximum speaker-level input: 400 watts @ 4 ohms Maximum output level: 8.5Vrms Output gain: ±15 dB Frequency response: 10Hz - 22,000 Hz Total harmonic distortion: 0.01% Input Impedance: 20 Kohms Output Impedance: 150 ohms Power supply: High headroom PWM switching Power draw: 350mA Recommended fuse rating: 2 Amp Remote Trigger Output Current: 1 Amp What is in the LC7i box: 6-Channel line-output converter Instructions/Specs/Warranty (on packaging) Quality Control Certificate AudioControl LC7i owner's manual AudioControl Remote ACR-1 Dash Mount Wired Remote Level Control for Select AudioControl Sound Processors Add remote level control for your AudioControl processor or amplifier. This is the replacement remote for the Epicenter. Comes with a 20-foot cable and removable mounting enclosure (for custom dash installations).s. General Features Wired Remote Level Control Mounts on the dash using built-in bracket Detachable mounting plate Works with select AudioControl sound processors Direct replacement remote for the Epicenter Includes 20' power cable Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) compatible with 6XS ACM-1.300 The Epicenter® Concert Series LC2i LC6i LC7i Overdrive Plus Matrix Plus LC-4.800 LC-6.1200 legacy products supported LC6 LC8 Original Epicenter® (bypass not supported) What is in the ACR-1 box: Remote dash mount control 20' RJ-14 cable. Mounting Instructions on packaging AudioControl ACR-1 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

AudioControl LC7i 6-channel line output converter with bass restoration adds aftermarket subs and amps to a factory system (Black) Want to add your own speakers, subs, and amps to a factory system? AudioControl's LC7i 6-channel line output converter (LOC) with bass restoration allows you to add aftermarket amps, speakers, and subs to your car's factory radio, so you can enjoy better and more powerful sound without losing climate controls, voice-activated functions, or other built-in factory features. The LC7i accepts speaker-level signals, so you can use it with just about any setup, even high-powered amplified systems. Summing The LC7i sums its input signals together, even if they've been crossed over for tweeters, mids, and subs by the factory system. That way, you can count on a strong, smooth, full-range signal for your processors and amps. The LC7i features six RCA preamp outputs that'll handle a traditional front/rear/sub setup. Why you have to restore the bass Many factory radios actually turn the bass down as you increase the volume to protect the cheap factory speakers, subsequently removing much of your music's power and punch. AudioControl developed a patent pending AccuBASS™ circuit that restores the bass the factory radio erased, giving you much fuller and more enjoyable sound. The AccuBASS is applied to the subwoofer output channel, so your sub amp can have the entire, restored signal to work with. Level-matching with an LED indicator AudioControl makes it easy: set your factory stereo to about 3/4 maximum volume, turn the output level control of the LC7i until the "Maximized" light begins to flicker, then adjust the gain controls on your amps and you're done. You've level-matched the output of your receiver to the amplifier's input, so you can count on getting maximum performance and minimum noise from your system. Convenience The optional dash-mounted ACR-1 wired remote allows you to adjust the volume of the bass while you're on the go. The speaker-level inputs sense incoming signals and turn on the LC7i, while a built-in 12-volt trigger turns on your amps as well. If your factory system only has channels for front and rear speakers, AutoMode™ will create the output you can use for your subs Product highlights: 6-channel line output converter plus bass restoration 6 speaker-level inputs (each can handle up to 400 watts RMS) internal channel summing AccuBASS™ bass restoration circuitry 6 preamp outputs (up to 8.5 volts RMS) level matching controls with Maximized Indicator LED Other Features: optional wired remote subwoofer level controller available (#161ACR1) AutoMode™ turns 4-channel input to 6-channel output GTO™ signal-sensing turn on 12-volt turn-on lead output recommended fuse rating: 2 amps 8-11/16"W x 1-3/8"H x 6-9/16"D warranty: 5 years 6-Channel line output converter (black) Owner's manual QC checklist ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

AudioControl LC7i 6-channel line output converter with bass restoration adds aftermarket subs and amps to a factory system (Black)+ Free Absolute Electrical Tape+ Phone Holder Want to add your own speakers, subs, and amps to a factory system? AudioControl's LC7i 6-channel line output converter (LOC) with bass restoration allows you to add aftermarket amps, speakers, and subs to your car's factory radio, so you can enjoy better and more powerful sound without losing climate controls, voice-activated functions, or other built-in factory features. The LC7i accepts speaker-level signals, so you can use it with just about any setup, even high-powered amplified systems. Summing The LC7i sums its input signals together, even if they've been crossed over for tweeters, mids, and subs by the factory system. That way, you can count on a strong, smooth, full-range signal for your processors and amps. The LC7i features six RCA preamp outputs that'll handle a traditional front/rear/sub setup. Why you have to restore the bass Many factory radios actually turn the bass down as you increase the volume to protect the cheap factory speakers, subsequently removing much of your music's power and punch. AudioControl developed a patent pending AccuBASS™ circuit that restores the bass the factory radio erased, giving you much fuller and more enjoyable sound. The AccuBASS is applied to the subwoofer output channel, so your sub amp can have the entire, restored signal to work with. Level-matching with an LED indicator AudioControl makes it easy: set your factory stereo to about 3/4 maximum volume, turn the output level control of the LC7i until the "Maximized" light begins to flicker, then adjust the gain controls on your amps and you're done. You've level-matched the output of your receiver to the amplifier's input, so you can count on getting maximum performance and minimum noise from your system. Convenience The optional dash-mounted ACR-1 wired remote allows you to adjust the volume of the bass while you're on the go. The speaker-level inputs sense incoming signals and turn on the LC7i, while a built-in 12-volt trigger turns on your amps as well. If your factory system only has channels for front and rear speakers, AutoMode™ will create the output you can use for your subs Product highlights: 6-channel line output converter plus bass restoration 6 speaker-level inputs (each can handle up to 400 watts RMS) internal channel summing AccuBASS™ bass restoration circuitry 6 preamp outputs (up to 8.5 volts RMS) level matching controls with Maximized Indicator LED Other Features: optional wired remote subwoofer level controller available (#161ACR1) AutoMode™ turns 4-channel input to 6-channel output GTO™ signal-sensing turn on 12-volt turn-on lead output recommended fuse rating: 2 amps 8-11/16"W x 1-3/8"H x 6-9/16"D warranty: 5 years 6-Channel line output converter (black) Owner's manual QC checklist Absolute BT1700 Vinyl Electrical Tape is good quality, multi-purpose vinyl insulating tape. It has great resistance to moisture and varying weather conditions. It is a polyvinyl chloride (PVC) tape that is flame-retardant and conformable. Details Resists abrasion, moisture, alkalis, solvents, and acids Flame-retardant and inhibits the corrosion of electrical conductors Made of durable PVC Compatible with rubber and synthetic splicing compounds Withstands a temperature range of 32 to 194 °F (0 to 90 °C) UL Listed, CSA and VDE Certified Specifications Adhesive Type Rubber Application Insulation Brand Absolute Elongation at Break 200 % Maximum Operating Temperature (Celsius) 90 Degree Celsius Maximum Operating Temperature (Fahrenheit) 194 Degree Fahrenheit Minimum Operating Temperature (Fahrenheit) 32 Degree Fahrenheit Overall Length (Imperial) 60 ft Overall Length (Metric) 18 m Overall Width (Imperial) 0.75 in Overall Width (Metric) 19 mm Product Color Black Shelf Life 5 Year Tape Grade General Use ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Audio Control LC7i 6 Channel Line Out Converter with bass restoration adds aftermarket subs and amps to a factory system The AudioControl LC7i, six channel active line converter, allows all music lovers, who want a great in-car audio experience, to keep their factory-installed source unit and dramatically improve their system performance. The LC7i delivers amazing sound quality and fixes one of the biggest letdowns of today’s factory systems, weak BASS! Designed for maximum sound quality and enhanced audio performance, the LC7i incorporates AccuBASS™. This patented process automatically corrects for the bass roll-off that is common with many factory-installed audio systems and AudioControl’s unique and exclusive AccuBASS™ circuitry maintains and restores the Bass as the volume is turned up, improving the audio performance. The LC7i allows the flexibility of powering the audio signals downstream to single or multiple factory amps maximizing sound quality & achieving high output at a great price. In addition, the LC7i is designed to fit into a compact chassis allowing an easy & flexible factory system upgrade in today’s space constrained vehicles. The ACR-1 dash remote (sold separately) allows the user to control the level of the low-frequency output. Add remote level control for your AudioControl processor or amplifier. This is the replacement remote for the Epicenter. Comes with a 20-foot cable and removable mounting enclosure (for custom dash installations).s. General Features: Six Input and Output Channels 6 Speaker Level Inputs - Can Accept 400-Watt Signals! Signal sensing inputs GTO (Great Turn-On) Circuit Internal Channel Summing AutoMode inputs Level matching controls 12-volt trigger output Line Output Converter: A device for converting a powered (or amplified) signal into a pre-amp line level (or non-powered) signal Input for optional subwoofer level control: AudioControl ACR-1 Color: Black Weight: 3.0 lbs Size: 7.5" W x 4.72" D x 1.22" H Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) LC6i Specifications: Maximum speaker-level input: 400 watts @ 4 ohms Maximum output level: 8.5Vrms Output gain: +/-12 dB Frequency response: 10Hz-22kHz Total harmonic distortion: 0.01% Input Impedance: 20K Ohms Output Impedance: 150 ohms Power supply: High headroom PWM switching Power draw: 350mA Recommended fuse rating: 2 Amp Remote Trigger Output Current: 1 Amp What is in the box: 6-Channel line-output converter Instructions/Specs/Warranty (on packaging) Quality Control Certificate AudioControl LC7i owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

AudioControl Remote ACR-1 Dash Mount Wired Remote Level Control for Select AudioControl Sound Processors Add remote level control for your AudioControl processor or amplifier. This is the replacement remote for the Epicenter. Comes with a 20-foot cable and removable mounting enclosure (for custom dash installations).s. General Features Wired Remote Level Control Mounts on the dash using built-in bracket Detachable mounting plate Works with select AudioControl sound processors Direct replacement remote for the Epicenter Includes 20' power cable Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) compatible with 6XS ACM-1.300 The Epicenter® Concert Series LC2i LC6i LC7i Overdrive Plus Matrix Plus LC-4.800 LC-6.1200 legacy products supported LC6 LC8 Original Epicenter® (bypass not supported) What is in the ACR-1 package: Remote dash mount control 20' RJ-14 cable. Mounting Instructions on packaging ACR-1 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

AudioControl The Epicenter Digital Bass Restoration Processor You like all the bumpin' bass you hear in hip hop, rap, and EDM? Well you can put that deep, biting bass into any kind of music — from classical, jazz, and rock to folk and Tejano — with an AudioControl Epicenter bass restoration processor. Most factory radios dial down bass response to protect flimsy speakers, so when you do add a subwoofer, there's no bass to play. The Epicenter will bring it back. AudioControl's legendary Epicenter bass processor maximizes the low-frequency power and punch of your bass system, whether it's a simple powered bass tube or a full-blown competition setup. Simply install this processor between your receiver and your amplifiers or crossovers, and you'll finally be able to hear all the good bass you've been missing. An included wired remote lets you control the amount of thump from the front seat. How does it do it? Sophisticated processing analyzes the incoming signal and synthesizes low-bass fundamental tones, increasing bass response tremendously. The Epicenter connects to any receiver with preamp outputs — its balanced inputs will reject noise from your car's electrical system. A subsonic filter removes extreme low frequencies from your signal so your amps and subs will play more efficiently, while a single band ParaBass equalizer lets you fine-tune the bass tone. Upgrade available AudioControl's Epicenter bass restoration processing is also available in The Epicenter Micro, which features a compact chassis, high-level inputs, and selectable load resistors for better OEM factory system integration. Product highlights: bass restoration processor increases bass response from your system 2-channel preamp inputs and outputs Para-Bass controls adjust center-frequency and width of bass EQ processing fixed subsonic filter (33 Hz, 12/dB octave) wired remote bass level controller frequency response: 10 to 100,000 Hz fuse rating: 1A 8-1/16"W x 1-1/4"H x 6-3/4"H warranty: 5 years Pre-amp Bass Restoration Processor (black) Remote dash mount control 20' RJ-14 cable Owner's manual QC checklist ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

AudioControl The Epicenter Digital Bass Restoration Processor + Free Absolute Electrical Tape+ Phone Holder You like all the bumpin' bass you hear in hip hop, rap, and EDM? Well you can put that deep, biting bass into any kind of music — from classical, jazz, and rock to folk and Tejano — with an AudioControl Epicenter bass restoration processor. Most factory radios dial down bass response to protect flimsy speakers, so when you do add a subwoofer, there's no bass to play. The Epicenter will bring it back. AudioControl's legendary Epicenter bass processor maximizes the low-frequency power and punch of your bass system, whether it's a simple powered bass tube or a full-blown competition setup. Simply install this processor between your receiver and your amplifiers or crossovers, and you'll finally be able to hear all the good bass you've been missing. An included wired remote lets you control the amount of thump from the front seat. How does it do it? Sophisticated processing analyzes the incoming signal and synthesizes low-bass fundamental tones, increasing bass response tremendously. The Epicenter connects to any receiver with preamp outputs — its balanced inputs will reject noise from your car's electrical system. A subsonic filter removes extreme low frequencies from your signal so your amps and subs will play more efficiently, while a single band ParaBass equalizer lets you fine-tune the bass tone. Upgrade available AudioControl's Epicenter bass restoration processing is also available in The Epicenter Micro, which features a compact chassis, high-level inputs, and selectable load resistors for better OEM factory system integration. Product highlights: bass restoration processor increases bass response from your system 2-channel preamp inputs and outputs Para-Bass controls adjust center-frequency and width of bass EQ processing fixed subsonic filter (33 Hz, 12/dB octave) wired remote bass level controller frequency response: 10 to 100,000 Hz fuse rating: 1A 8-1/16"W x 1-1/4"H x 6-3/4"H warranty: 5 years Pre-amp Bass Restoration Processor (black) Remote dash mount control 20' RJ-14 cable Owner's manual QC checklist Absolute BT1700 Vinyl Electrical Tape is good quality, multi-purpose vinyl insulating tape. It has great resistance to moisture and varying weather conditions. It is a polyvinyl chloride (PVC) tape that is flame-retardant and conformable. Details Resists abrasion, moisture, alkalis, solvents, and acids Flame-retardant and inhibits the corrosion of electrical conductors Made of durable PVC Compatible with rubber and synthetic splicing compounds Withstands a temperature range of 32 to 194 °F (0 to 90 °C) UL Listed, CSA and VDE Certified Specifications Adhesive Type Rubber Application Insulation Brand Absolute Elongation at Break 200 % Maximum Operating Temperature (Celsius) 90 Degree Celsius Maximum Operating Temperature (Fahrenheit) 194 Degree Fahrenheit Minimum Operating Temperature (Fahrenheit) 32 Degree Fahrenheit Overall Length (Imperial) 60 ft Overall Length (Metric) 18 m Overall Width (Imperial) 0.75 in Overall Width (Metric) 19 mm Product Color Black Shelf Life 5 Year Tape Grade General Use ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

AudioControl The Epicenter® Micro Bass restoration processor and line output converter Add bass to your aftermarket system's high-level sourceMost factory radios dial down deep, low-hitting bass notes to protect flimsy factory speakers. The Epicenter Micro from AudioControl takes amplified speaker-level signals, converts them into the high-quality preamp signals your sub amp needs, and then adds the bass that's missing. Even when listening to traditionally bass-weak classical, jazz, folk, or Tejano music, you'll finally be able to hear all the good bass you've been missing How does it do it? Sophisticated processing analyzes the incoming signal and synthesizes low-bass fundamental tones, increasing bass response tremendously. A single band ParaBASS® equalizer lets you fine-tune your subwoofer's tone. A selectable subsonic filter removes extreme low frequencies so your amps and subs will play more efficiently. The Epicenter Micro will also connect to any receiver with preamp outputs — its balanced inputs will reject noise from your car's electrical system for ultra-clean output. Installation conveniences The included ACR-4 dash-mount wired remote control allows you to adjust the level of your sub channel on the go. Load selection switches make OEM factory system integration easier, so The Epicenter Micro will work with almost any vehicle's sound system. Selectable turn-on modes include GTO™ Signal Sense (DC offset), audio sigal , or remote 12-volt input. Product highlights: active 2-channel line driver/output converter with bass restoration designed to work with aftermarket and factory systems provides up to 9.5 Vrms output (selectable level: 5, 7, 10V) preamp and speaker-level inputs speaker-level inputs handle up to 40V (400 watts RMS) speaker-level inputs feature switchable load resistance (20, 60, or 20,000 ohms) to prevent factory stereo shut-down Epicenter bass restoration increases bass response Para-Bass controls adjust center-frequency and width of bass EQ processing More info: ACR-4 wired remote included switchable Programmable Frequency Match (PFM) subsonic filter (20 Hz, 12/dB octave) selectable ground isolation helps eliminate noise auto turn-on via 12V remote, DC offset, or audio signal detect 12-volt turn-on lead output wiring, fuse, and hardware not included with device 18-gauge power and ground leads and a 1-amp fuse recommended dimensions: 5-1/8" W x 1" H x 3" D warranty: 5 years ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov