Rockford Fosgate Monoblock Amplifiers (39)

Rockford Fosgate Prime R2-500X1 500W Prime Series Monoblock Subwoofer Class D Amplifier Primed for performance, the R2-500X1 amplifier is a 500 watt, class-D, capable of operating at 4Ω or 2Ω mono. This amplifier is extremely efficient because of its class D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allows you to tune the bass for the desired level for the music. General Features: Rockford Fosgate Prime R2-500X1 RMS Power Rating: 4 ohms: 300 watts x 1 chan. 2 ohms: 500 watts x 1 chan. Total power output: 500 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeat able Auto Turn-On Circuit Features C.L.E.A.N. Set-up Variable Input Gain adjustment level R.L.C. Remote Level Control Variable Infrasonic Filter Continuously Variable On Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Full Range Class D Rollback Protection Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers Input sensitivity: Low-Level: 150 mV - 4 V High-Level: 450 mV - 12 V Frequency Response: 20 Hz - 250 Hz Total Harmonic Distortion (THD): >1% Crossover Controls Low-Pass: 50 Hz - 250 Hz Sub Infrasonic: 15 Hz - 40 Hz Recommended Fuse Rating: 80A 4 gauge power and ground wiring is recommended for installation Dimensions: "1.9" x "6.8" x "8.5" Authorized Internet Dealer 1 Year Manufacturer's Warranty What is in the R2-500X1 package: Rockford Fosgate R2-500X1 owner's manual Mono subwoofer amplifier Wired Remote Level Control module 16' Remote cable (RJ-25 connector on both ends) One 7" Speaker input harnesses 3mm Allen Hex key Four 3/4" Screws Two 1/2" Screws 5 Flat washers 1 Nut Installation and Operation Instructions Certificate of Performance Rockford Fosgate contact information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca

Rockford Fosgate T1500-1bdcp Power Series mono sub amplifier 1,500 watts RMS x 1 at 2 ohms + Rockford Fosgate Power T1D412 12" Dual 4-ohm Voice Coil Component subwoofers Powerful bass performanceRockford Fosgate enjoys a well-deserved reputation for building high-quality mobile audio products. Their Power Series amps sit at the top of the car audio food chain, with proven durability and proprietary technologies that deliver stronger, more reliable performance than most other amps on the planet today. Rockford Fosgate's high-tech solutions yield more powerPower Series amplifiers actively monitor their speakers' performance using Rockford Fosgate's Constant Power technology. A speaker's impedance naturally fluctuates as it performs. So, just like your cruise control increases the engine's RPM to maintain your car's speed uphill, Constant Power maintains this amp's output by increasing its internal voltage and current when the speaker's impedance rises. This results in up to a 25% increase in the amp's total power output, especially in the crucial range below 50 Hz where a sub amp really has to shine.Rugged construction, massive bass Rockford Fosgate builds each Power Series mono amplifier with heavy-duty, state-of-the-art components. The award-winning Dynamic Thermal Management design manages the temperature of the internal components, distributing heat evenly for higher efficiency and lower distortion. The unique heat sink allows the heat to escape more readily so the high-power output transistors stay cooler and last longer. The T1500-1bdCP mono sub amp uses an efficient Class bd design to deliver up to 1,500 watts to your subwoofer system from a remarkably compact chassis. This amp can even drive a 1-ohm load, so you can get massive bass out of a wide variety of system designs. The variable 24/dB per octave crossover creates a more natural-sounding transition from your speakers to your subs. And the 2-year warranty tells you that Rockford Fosgate stands behind this bass behemoth. Product highlights: mono subwoofer amplifier 1,000 watts RMS x 1 at 4 ohms (1,500 watts RMS x 1 at 2 ohms) 1,500 watts RMS x 1 at 1 ohm CEA-2006 compliant Dynamic Thermal Management cooling system variable low-pass filter (35-250 Hz, 24 dB/octave) selectable subsonic filter (28Hz, 24 dB/octave) variable bass boost (0-18 dB at 45 Hz) optional wired remote bass boost Class-BD amplifier design MOSFET power and output stages preamp-level inputs and outputs 4-gauge power and ground leads and a 200-amp fuse recommended — wiring and hardware not included with amplifier no onboard fuses — when installing multiple amps in a system, an additional 200-amp in-line fuse between the distribution block and the amplifier is recommended 14-15/16"W x 2-1/4"H x 8-15/16"D warranty: 2 years ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate T1500-1bdcp Power Series mono sub amplifier 1,500 watts RMS x 1 at 2 ohms + RFK4 Wire Install Kit Powerful bass performanceRockford Fosgate enjoys a well-deserved reputation for building high-quality mobile audio products. Their Power Series amps sit at the top of the car audio food chain, with proven durability and proprietary technologies that deliver stronger, more reliable performance than most other amps on the planet today. Rockford Fosgate's high-tech solutions yield more powerPower Series amplifiers actively monitor their speakers' performance using Rockford Fosgate's Constant Power technology. A speaker's impedance naturally fluctuates as it performs. So, just like your cruise control increases the engine's RPM to maintain your car's speed uphill, Constant Power maintains this amp's output by increasing its internal voltage and current when the speaker's impedance rises. This results in up to a 25% increase in the amp's total power output, especially in the crucial range below 50 Hz where a sub amp really has to shine.Rugged construction, massive bass Rockford Fosgate builds each Power Series mono amplifier with heavy-duty, state-of-the-art components. The award-winning Dynamic Thermal Management design manages the temperature of the internal components, distributing heat evenly for higher efficiency and lower distortion. The unique heat sink allows the heat to escape more readily so the high-power output transistors stay cooler and last longer. The T1500-1bdCP mono sub amp uses an efficient Class bd design to deliver up to 1,500 watts to your subwoofer system from a remarkably compact chassis. This amp can even drive a 1-ohm load, so you can get massive bass out of a wide variety of system designs. The variable 24/dB per octave crossover creates a more natural-sounding transition from your speakers to your subs. And the 2-year warranty tells you that Rockford Fosgate stands behind this bass behemoth. Product highlights: mono subwoofer amplifier 1,000 watts RMS x 1 at 4 ohms (1,500 watts RMS x 1 at 2 ohms) 1,500 watts RMS x 1 at 1 ohm CEA-2006 compliant Dynamic Thermal Management cooling system variable low-pass filter (35-250 Hz, 24 dB/octave) selectable subsonic filter (28Hz, 24 dB/octave) variable bass boost (0-18 dB at 45 Hz) optional wired remote bass boost Class-BD amplifier design MOSFET power and output stages preamp-level inputs and outputs 4-gauge power and ground leads and a 200-amp fuse recommended — wiring and hardware not included with amplifier no onboard fuses — when installing multiple amps in a system, an additional 200-amp in-line fuse between the distribution block and the amplifier is recommended 14-15/16"W x 2-1/4"H x 8-15/16"D warranty: 2 years ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate T750x1BD Power 500 Watts Watt Class-AD Mono Channel Amplifier + Absolute KIT4 4 Gauge Amplifier Installation Wiring Kit The Power T750X1bd is an ultra-compact, Class bd 750-watt mono amplifier. It features a high-level auto turn-on, the CLEAN circuit with input/output clip detection, top-mounted controls, and dual fan forced induction cooling. Additionally, it has our patented Punch EQ circuit built in and Differential inputs with auto turn-on capabilities. Perfect for hybrid, electric, small cars, trucks, motorcycles, and side-by-side UTVs. General Features: Rockford Fosgate T750X1bd Class-BD 1-Ohm Stable Monoblock Amplifier RMS Power Rating: 4 ohms: 500 watts x 1 chan. 2 ohms: 750 watts x 1 chan. 1 ohm: 750 watts x 1 chan. Total power output: 750 watts CEA-2006 Compliant Amplifier Perfect for hybrid, electric, small cars, trucks, motorcycles, and side-by-side UTVs Optional remote Punch Level Control (PLC2 ready (w/ input clip indicator) LED power (blue), protect (red), input clip (red), and output clip (blue/red) indicators L.E.A.N. input/output clip detection and indicator LEDs Top-mounted controls Built-in Punch EQ circuit Real-time thermal sensing with Rollback technology Remote-Out feature when using high-level inputs Rockford Fosgate proprietary low impedance Constant Power Mono channel operation Speaker-level (high-level) inputs with auto turn-on 3-way protection circuitry (thermal, overload, and speaker short protection) Dual extruded heat sinks Dual fan cooled Input sensitivity: 150mV to 12V Speaker wire gauge: 10 AWG Frequency Response: 20 - 230Hz Total Harmonic Distortion (THD): <1.0% Variable low-pass filter: 50 - 250 Hz, 12 dB/octave Variable Bass Boost: 0 to +18 dB bass boost at 45 Hz Recommended Fuse: 100A (not included) 2-Year Warranty Absolute KIT 4 Gauge Amp Kit 17 ft. of red 4 AWG high current power cable 3 ft. of black 4 AWG ground cable 15 ft. of RCA triple shielded interconnect audio cable with built-in remote wire 20 ft. of 12 AWG OFC Speaker cable 20 ft. of 16 AWG remote turn-on wire 6 ft. of split loom tubing 1 Gold-plated 80 AMP AGU fuse 1 4 AWG gold ring terminal 750W Power Series Ultra-Compact Class-BD Monoblock Amplifier 500 Watts RMS x 1 @ 4 ohms 750 Watts RMS x 1 @ 2 ohms 750 Watts RMS x 1 @ 1 ohm Complete 4 Gauge Amplifier Kit For Use in Any Car, Truck, RV, or Boat ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate T750x1BD Power 500 Watts Watt Class-AD Mono Channel Amplifier + Absolute KIT4 4 Gauge Amplifier Installation Wiring Kit The Power T750X1bd is an ultra-compact, Class bd 750-watt mono amplifier. It features a high-level auto turn-on, the CLEAN circuit with input/output clip detection, top-mounted controls, and dual fan forced induction cooling. Additionally, it has our patented Punch EQ circuit built in and Differential inputs with auto turn-on capabilities. Perfect for hybrid, electric, small cars, trucks, motorcycles, and side-by-side UTVs. General Features: Rockford Fosgate T750X1bd Class-BD 1-Ohm Stable Monoblock Amplifier RMS Power Rating: 4 ohms: 500 watts x 1 chan. 2 ohms: 750 watts x 1 chan. 1 ohm: 750 watts x 1 chan. Total power output: 750 watts CEA-2006 Compliant Amplifier Perfect for hybrid, electric, small cars, trucks, motorcycles, and side-by-side UTVs Optional remote Punch Level Control (PLC2 ready (w/ input clip indicator) LED power (blue), protect (red), input clip (red), and output clip (blue/red) indicators L.E.A.N. input/output clip detection and indicator LEDs Top-mounted controls Built-in Punch EQ circuit Real-time thermal sensing with Rollback technology Remote-Out feature when using high-level inputs Rockford Fosgate proprietary low impedance Constant Power Mono channel operation Speaker-level (high-level) inputs with auto turn-on 3-way protection circuitry (thermal, overload, and speaker short protection) Dual extruded heat sinks Dual fan cooled Input sensitivity: 150mV to 12V Speaker wire gauge: 10 AWG Frequency Response: 20 - 230Hz Total Harmonic Distortion (THD): <1.0% Variable low-pass filter: 50 - 250 Hz, 12 dB/octave Variable Bass Boost: 0 to +18 dB bass boost at 45 Hz Recommended Fuse: 100A (not included) 2-Year Warranty Absolute KIT 4 Gauge Amp Kit 17 ft. of red 4 AWG high current power cable 3 ft. of black 4 AWG ground cable 15 ft. of RCA triple shielded interconnect audio cable with built-in remote wire 20 ft. of 12 AWG OFC Speaker cable 20 ft. of 16 AWG remote turn-on wire 6 ft. of split loom tubing 1 Gold-plated 80 AMP AGU fuse 1 4 AWG gold ring terminal 750W Power Series Ultra-Compact Class-BD Monoblock Amplifier 500 Watts RMS x 1 @ 4 ohms 750 Watts RMS x 1 @ 2 ohms 750 Watts RMS x 1 @ 1 ohm Complete 4 Gauge Amplifier Kit For Use in Any Car, Truck, RV, or Boat ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Prime R2-500X1 500W Prime Series Monoblock Subwoofer Class D Amplifier Primed for performance, the R2-500X1 amplifier is a 500 watt, class-D, capable of operating at 4Ω or 2Ω mono. This amplifier is extremely efficient because of its class D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allows you to tune the bass for the desired level for the music. General Features: Rockford Fosgate Prime R2-500X1 RMS Power Rating: 4 ohms: 300 watts x 1 chan. 2 ohms: 500 watts x 1 chan. Total power output: 500 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeat able Auto Turn-On Circuit Features C.L.E.A.N. Set-up Variable Input Gain adjustment level R.L.C. Remote Level Control Variable Infrasonic Filter Continuously Variable On Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Full Range Class D Rollback Protection Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers Input sensitivity: Low-Level: 150 mV - 4 V High-Level: 450 mV - 12 V Frequency Response: 20 Hz - 250 Hz Total Harmonic Distortion (THD): >1% Crossover Controls Low-Pass: 50 Hz - 250 Hz Sub Infrasonic: 15 Hz - 40 Hz Recommended Fuse Rating: 80A 4 gauge power and ground wiring is recommended for installation Dimensions: "1.9" x "6.8" x "8.5" Authorized Internet Dealer 1 Year Manufacturer's Warranty What is in the R2-500X1 package: Rockford Fosgate R2-500X1 owner's manual Mono subwoofer amplifier Wired Remote Level Control module 16' Remote cable (RJ-25 connector on both ends) One 7" Speaker input harnesses 3mm Allen Hex key Four 3/4" Screws Two 1/2" Screws 5 Flat washers 1 Nut Installation and Operation Instructions Certificate of Performance Rockford Fosgate contact information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca

Rockford Fosgate M2-500X1 Marine 500-Watt Mono Amplifier Designed to withstand the elements, the M2-500X1 Element Ready amplifier is a 500-watt, class-D model, capable of operating at 4Ω or 2Ω mono. This amplifier is extremely efficient because of its class D technology which reduces demand on the electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allow you to tune the bass for the desired level for the music. General Features: mono marine subwoofer amplifier 300 watts RMS x 1 at 4 ohms 500 watts RMS x 1 at 2 ohms CTA-2006 compliant Class-D amplifier design wired remote included variable low-pass filter (50-250 Hz, 12 dB/octave) variable subsonic filter (15-40 Hz, 12 dB/octave) variable bass boost (0-18 dB at 45 Hz) marine features: Element Ready™ chassis and conformal-coated PC boards UV stable powder-coated cast aluminum heatsink zinc nickel-plated marine-grade brass connection terminals C.L.E.A.N. gain setup system includes clip lights auto remote turn-on preamp and speaker-level inputs preamp outputs wiring, fuse, and hardware not included with amplifier 4-gauge power and ground leads and an 80-amp fuse recommended dimensions: 8-1/2"W x 1-15/16"H x 6-13/16"D warranty: 2 years The M2-500X1 Element Ready Marine mono amplifier with 500 Watts RMS is packed with all the power and performance you have come to expect from Rockford Fosgate (Dimensions: 1.9" x 6.8" x 8.5") Class D technology makes this amp extremely efficient by reducing demand on the vehicles electrical system (RMS Power: 300 Watts x 1 @ 4Ω OR 500 Watts x 1 @ 2Ω) Built for the marine environment, this Element Ready amp features UV resistant protection, conformal coated circuit board, stainless steel mounting hardware, and marine-grade terminal connections to ensure long-lasting outdoor use Featuring C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass Famous Rockford Fosgate build quality with a full 2-year warranty when purchased from an authorized Rockford Fosgate reseller What is in the box: Mono marine amplifier Remote Punch Level Control module 16.5' Remote Punch Level Control cable (RJ-25 connector on both ends) 7" Speaker input harness 3mm Hex key Four 3/4" Screws Two 1/2" Screws 5 Flat washers 1 Nut Installation and Operation Instructions (English/ French/ Spanish/ German/ Italian) Certificate of Performance Verification Rockford Fosgate contacts information Rockford Fosgate M2-500X1 owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate PM100X1K Punch Marine 100 Watt Full-Range Mono Amplifier (Pair) The Punch Marine PM100X1 is a pair of 100-Watt full range dynamic power mono amplifiers that don’t need a power wire, is extremely compact in size, but big on power! The PM100X1 uses our patent-pending BTL technology that utilizes the speaker output of the radio to not only provide the audio signal it needs, but also the power that runs the unit. With no more load to the radio than a standard 2 or 4-ohm speaker, this design allows the amp to be connected to a 20-Watt output radio and produce up to 100 Watts dynamically! The small footprint of the PM100X1K amplifier allows it to be installed virtually anywhere along the speaker signal pathway from behind the radio to the door itself. This design makes the amplifier ideal for OEM or aftermarket as they can be hidden in the dash or doors of the vehicle. It is also IP67 water intrusion rated so it is also built to withstand the elements in motorcycle, boat, and motorsport applications. General Features: two compact mono amplifiers 60 watts RMS x 1 at 4 ohms (100 watts RMS x 1 at 2 ohms) CEA-2006 compliant patent-pending BTL "Freeload" technology requires no separate positive power lead connects to speaker wiring and chassis ground selectable high-pass filter (60, 80, or 100 Hz at 12 dB/octave) input impedance switch for low-impedance-capable receivers rubber switch cover IPX6 water intrusion rated dimensions: 3"W x 1-5/16"H x 3-15/16"D warranty: 2 years Patented BTL powered "Freeload" Technology Uses Stored Energy from BTL Amplifier to Produce Dynamic Power of Over 100 Watts High Level Turn On Pig Tail Connectivity for Easy Installation Sold in pairs (left/right) Harvests both B+ and Audio Signal from Standard Head Unit Speaker Outputs Optional B+ Connection for Non-Standard Speaker Outputs Short Circuit & Over Voltage Protection Extruded Aluminum Heat Sink and Thermal Protection Discrete surface mount technology Small Stealth Package that Allows for Anywhere Installation Selectable 4 and 2 Ohm Play Current Limited to Protect Head Unit for Both 4 Ohm and 2 Ohm Configurations Muted turn-on. The PM100X1K is a pair (left/right) of 100-Watt dynamic power mono amplifiers using DC and AC voltages present on existing radio speaker outputs This compact amplifier (1.3” x 3.0” x 3.9) is small but big on power (RMS Power Output: 60 x 1 @ 4-Ohm or 100 x 1 @ 2-Ohm) The versatile design can be used on a factory system using 2-Ohm or 4-Ohm factory or aftermarket speakers. The PM100X1K is also IPX6 rated so it can withstand the elements in mobile, motorsport, and marine applications High Level Turn on with selectable 60, 80, and 100 Hz Selectable 12dB/Oct HP Butterworth Crossover, featuring pigtail connectivity in a small stealth package allows for easy anywhere installation Famous Rockford Fosgate build quality ensures it will handle everything you throw at it! Full 2-year parts and labor warranty when purchased from an authorized Rockford Fosgate reseller What is in the box: The PM100X1K package contains two separately boxed PM100x1 mono amplifiers. Each amplifier box includes: Mono amplifier with attached 7.75" pigtail 12" Input/Output/Ground harness (16 AWG wires) 12" Power wire (16 AWG) 2 Self-tapping screws (3/4" length) Certificate of Performance Verification Rockford Fosgate PM100X1 owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca

Rockford Fosgate Punch P500X1BD 500W RMS Punch Series Monoblock Class D Car Power Amplifier + Absolute KIT4 Amp Kit The Punch P500X1bd is a mono amplifier capable of 500 Watts into a 1-Ohm load. The Class-BD technology produces bass more efficiently over traditional amps, and its frequency response allows it to be optimized for subwoofers. General Features: Punch BD Series Monoblock Class BD Car Amplifier RMS Power Rating: 4 ohms: 150 watts x 1 chan. 2 ohms: 300 watts x 1 chan. 1 ohm: 500 watts x 1 chan. CEA-2006 compliant amplifier MOSFET power supply Muted turn-on. Cast aluminum heatsink. 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protect indicators. Nickel-plated captive C-clamp terminals. Ultra-efficient Class BD circuitry to maximize amplifier power efficiency. On-board differential inputs eliminate noise picked up by the signal cable. Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately) MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span. Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances. Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low. DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowers the operating temperature and potential for noise-like circuit boards designed by aerospace manufacturers. Input sensitivity: 150mV - 12V On-board Punch EQ with +18dB boost @ 45Hz. Variable low-pass filter: 50-250 Hz Selectable infrasonic filter: off / 28 Hz Frequency response: 20 - 250 Hz Total Harmonic Distortion: <1.0% Dimensions: 11"L x 7-3/4"W x 2-3/8"H 8 AWG to 18 AWG speaker wire output terminals Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the P500X1bd box: Mono subwoofer amplifier Four 1-1/2" Self-tapping screws 2.5mm Allen wrench Quick setup instructions Certificate of Performance P500X1bd owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Punch P500X1BD 500W RMS Punch Series Monoblock Class D Car Power Amplifier The Punch P500X1bd is a mono amplifier capable of 500 Watts into a 1-Ohm load. The Class-BD technology produces bass more efficiently over traditional amps, and its frequency response allows it to be optimized for subwoofers. General Features Punch BD Series Monoblock Class BD Car Amplifier RMS Power Rating: 4 ohms: 150 watts x 1 chan. 2 ohms: 300 watts x 1 chan. 1 ohm: 500 watts x 1 chan. CEA-2006 compliant amplifier MOSFET power supply Muted turn-on. Cast aluminum heatsink. 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protect indicators. Nickel-plated captive C-clamp terminals. Ultra-efficient Class BD circuitry to maximize amplifier power efficiency. On-board differential inputs eliminate noise picked up by the signal cable. Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately) MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span. Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances. Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low. DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowering the operating temperature and potential for noise-like circuit boards designed by aerospace manufacturers. Input sensitivity: 150mV - 12V On-board Punch EQ with +18dB boost @ 45Hz. Variable low-pass filter: 50-250 Hz Selectable infrasonic filter: off / 28 Hz Frequency response: 20 - 250 Hz Total Harmonic Distortion: <1.0% Dimensions: 11"L x 7-3/4"W x 2-3/8"H 8 AWG to 18 AWG speaker wire output terminals Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the P500X1bd box: Mono subwoofer amplifier Four 1-1/2" Self-tapping screws 2.5mm Allen wrench Quick setup instructions Certificate of Performance P500X1bd owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Punch P500X1BD 500W RMS Punch Series Monoblock Class D Car Power Amplifier The Punch P500X1bd is a mono amplifier capable of 500 Watts into a 1-Ohm load. The Class-BD technology produces bass more efficiently over traditional amps, and its frequency response allows it to be optimized for subwoofers. General Features Punch BD Series Monoblock Class BD Car Amplifier RMS Power Rating: 4 ohms: 150 watts x 1 chan. 2 ohms: 300 watts x 1 chan. 1 ohm: 500 watts x 1 chan. CEA-2006 compliant amplifier MOSFET power supply Muted turn-on. Cast aluminum heatsink. 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protect indicators. Nickel-plated captive C-clamp terminals. Ultra-efficient Class BD circuitry to maximize amplifier power efficiency. On-board differential inputs eliminate noise picked up by the signal cable. MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span. Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances. Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low. DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowers the operating temperature and potential for noise-like circuit boards designed by aerospace manufacturers. Input sensitivity: 150mV - 12V On-board Punch EQ with +18dB boost @ 45Hz. Variable low-pass filter: 50-250 Hz Selectable infrasonic filter: off / 28 Hz Frequency response: 20 - 250 Hz Total Harmonic Distortion: <1.0% Dimensions: 11"L x 7-3/4"W x 2-3/8"H 8 AWG to 18 AWG speaker wire output terminals Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the P500X1bd : Mono subwoofer amplifier Four 1-1/2" Self-tapping screws 2.5mm Allen wrench Quick setup instructions Certificate of Performance P500X1bd owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate T750X1bd 750W Power Series Ultra-Compact Class-BD Monoblock Amplifier The Power T750X1bd 750 Watt mono, the ultra-compact amplifier is built on Rockford Fosgate’s patented Class bd technology platform. This design creates a highly efficient design that reduces the electrical impact on the vehicle charging system using the efficient Class D technology while maintaining fidelity, combining it with Class B topology. Flexible vehicle integration is achieved via a configurable input harness with Molex-style connectivity that accepts both RCA and speaker level signals, while our differential input circuitry eliminates signal noise from entering the amplifier resulting in a clean audio signal. The amplifier also has integrated auto turn-on capabilities when using speaker-level input signals. It converts its remote input terminal to an output that can turn on additional amplifiers. This can eliminate the need to source a separate remote turn-on signal for the amplifier from the vehicle. Top-mounted controls allow easy access to the built-in low-pass crossover: patented Punch EQ boost circuit and our patented C.L.E.A.N. input/output clip detection circuits. The 3-stage thermal lock extrusion with dual fan forced induction keeps everything cool. In contrast, our real-time thermal/protection schemes safeguard the amplifier during overheating or short-circuit conditions. The unit is also compatible with our Punch PLC2 remote level controller and is ideal for installations requiring a compact amplifier that can produce high-output power. General Features: Rockford Fosgate T750X1bd Class-BD 1-Ohm Stable Monoblock Amplifier RMS Power Rating: 4 ohms: 500 watts x 1 chan. 2 ohms: 750 watts x 1 chan. 1 ohm: 750 watts x 1 chan. Total power output: 750 watts CEA-2006 Compliant Amplifier Perfect for hybrid, electric, small cars, trucks, motorcycles, and side-by-side UTVs Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) LED power (blue), protect (red), input clip (red), and output clip (blue/red) indicators C.L.E.A.N. input/output clip detection and indicator LEDs Top-mounted controls Built-in Punch EQ circuit Real-time thermal sensing with Rollback technology Remote-Out feature when using high-level inputs Rockford Fosgate proprietary low impedance Constant Power Mono channel operation Speaker-level (high-level) inputs with auto turn-on 3-way protection circuitry (thermal, overload, and speaker short protection) Dual extruded heat sinks Dual fan cooled Input sensitivity: 150mV to 12V Speaker wire gauge: 10 AWG Frequency Response: 20 - 230Hz Total Harmonic Distortion (THD): <1.0% Variable low-pass filter: 50 - 250 Hz, 12 dB/octave Variable Bass Boost: 0 to +18 dB bass boost at 45 Hz Recommended Fuse: 100A (not included) Dimensions: 4.3"W x 8.3"L x 1.6"H Authorized Internet Dealer 1-year Manufacturer's Warranty ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Punch P1000X1bd Mono subwoofer amplifier 1,000 watts RMS x 1 at 1 ohm The Punch P1000X1bd mono amplifier pumps out 1,000 Watts into a 1-Ohm load. The Class-BD technology produces bass more efficiently over traditional amps, and its frequency response is optimized for subwoofers. With its super-efficient Class-BD circuit topology, the P1000X1bd assures maximum BOOM for your buck! Due to its dedicated low-frequency response, this amplifier is optimized for mid-bass speakers or subwoofers only. No need to worry because its 1-ohm capability will easily drive a pair of 4-ohm DVC subwoofers or quad-configuration of 2-ohm DVC subwoofers. General Features: Punch BD Series Monoblock Class BD Car Amplifier RMS Power Rating: 4 ohms: 300 watts x 1 channel 2 ohms: 500 watts x 1 channel 1 ohm: 1000 watts x 1 channel CEA-2006 compliant amplifier Features C.L.E.A.N. Set-up with the 10-step set-up procedure w/ input/output clip detection and indicator LEDs MOSFET power supply Muted turn on Cast aluminum heatsink 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protection indicators Nickel-plated captive C-clamp terminals Ultra-efficient Class BD circuitry to maximize amplifier power efficiency On-board differential inputs eliminate noise picked up by the signal cable Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately) MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowering the operating temperature and potential for noise - similar to circuit boards designed by aerospace manufacturers Input sensitivity: 150mV - 12V On-board Punch EQ with +18dB boost @ 45Hz. Variable low-pass filter: 50-250 Hz Selectable infrasonic filter: off / 28 Hz Frequency response: 20 - 250 Hz Total Harmonic Distortion: <1.0% Dimensions: 13-5/16"L x 7-3/4"W x 2-3/8"H 8 AWG to 18 AWG speaker wire output terminals 4 gauge power and ground wiring is recommended for installation. Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the P1000X1bd package: P1000X1bd owner's manual Mono subwoofer amplifier Four 1-1/2" Self-tapping screws 5mm Allen wrench Quick setup instructions ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Prime R2-750X1 750W Prime Series Monoblock Subwoofer Class D Amplifier Primed for performance, the R2-750X1 amplifier is a 750-watt, Class-D, capable of operating at 4Ω, 2Ω, or 1Ω mono. This amplifier is extremely efficient because of its Class-D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allow you to tune the bass for the desired level of the music. Rockford Fosgate's R2 amplifiers are the building blocks for great audio systems, powerful enough to even DRIVE our Punch speakers and subwoofers. They have undergone an amazing upgrade by packing them with the latest features at an incredible value. Best of all, they are designed and engineered here in Tempe, Arizona. General Features: Rockford Fosgate Prime R2-750X1 RMS Power Rating: 4 ohms: 250 watts x 1 channel RMS Power Rating: 2 ohms: 500 watts x 1 channel RMS Power Rating: 1 ohm: 750 watts x 1 channel Total power output: 500 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeatable Auto Turn on Circuit Features C.L.E.A.N. Set-up Variable Input Gain adjustment level R.L.C. Remote Level Control Variable Infrasonic Filter Continuously Variable On-Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Full Range Class D Rollback Protection Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers Input sensitivity: Low-Level: 150 mV - 4 V Input sensitivity: High-Level: 450 mV - 12 V Frequency Response: 20 Hz - 250 Hz Total Harmonic Distortion (THD): >1% Crossover Controls: Low-Pass: 50 Hz - 250 Hz Crossover Controls: Sub Infrasonic: 15 Hz - 40 Hz Recommended Fuse Rating: 120A 4-gauge power and ground wiring are recommended for installation. Dimensions: "1.9" x "6.8" x "10.1" Authorized Internet Dealer 1-Year Manufacturer's Warranty What is in the R2-750X1 package: Mono subwoofer amplifier Wired Remote Level Control module 16' Remote cable (RJ-25 connector on both ends) One 7" Speaker input harness 3mm Allen Hex key Four 3/4" Screws Two 1/2" Screws 5 Flat washers 1 Nut Installation and Operation Instructions Certificate of Performance Rockford Fosgate contact information Rockford Fosgate R2-500X1 owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.