Rockford Fosgate Amplifiers (77)

Rockford Fosgate 600W Punch Series 4-Channel Stereo Class AB Car Power Amplifier The Punch P600X4 is a 4-channel amplifier producing 150 Watts into all four channels at 2-Ohm. The P600X4 is perfect for a 4-way full-range system or a 3-way system having a front stage with subwoofers on the rear channels. The Punch P600X4 multi-channel amplifier is versatile to power any audio system configuration. The stealth top-mounted control panel not only provides a sleek finished look to the amp but also protects the vital controls. Our custom heat sink design uses high aluminum mass where it is needed most to maximize heat transfer from the output MOSFETS to the surrounding air, keeping the circuitry cool even under high power and output demand. General Features: Punch Series 4-Channel Class AB Car Amplifier RMS Power Rating: 4 ohms: 75 watts x 4 channel 2 ohms: 150 watts x 4 channel Bridged, 4 ohms: 300 watts x 2 channel MOSFET power supply Remote bass level input (remote level control sold separately) LED power, thermal, and protect indicators Tuned Bass EQ (0-18 dB bass boost at 45 Hz or 0-14 dB bass boost at 12 kHz depending on crossover selection) On-board differential inputs eliminate noise picked up by the signal cable 4/3/2 or Mono channel operation Integrated Trans ana technology simplifies the signal path of the amplifier allowing the signal to travel through the amplifier at a lower voltage. The result is greater reliability and exceptional sound quality RCA Pass-thru outputs MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowers the operating temperature and potential for noise - similar to circuit boards designed by aerospace manufacturers Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low Nickel-plated RCA level inputs Nickel-plated captive C-clamp terminals Variable high-pass filter (50-250 Hz, Butterworth, 12 dB/octave) Variable low-pass filter (50-250 Hz, Butterworth, 12 dB/octave) CEA-2006 compliant amplifier Frequency response: 20-20000 Hz Dimensions: 13-5/16"L x 7-3/4"W x 2-3/8"H What is in the box: 4-Channel amplifier Four 1-1/2" Self-tapping screws 2.5mm Allen wrench Quick setup instructions Certificate of Performance Rockford Fosgate Punch P600X4 owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Prime R2-500X1 500W Prime Series Monoblock Subwoofer Class D Amplifier Primed for performance, the R2-500X1 amplifier is a 500 watt, class-D, capable of operating at 4Ω or 2Ω mono. This amplifier is extremely efficient because of its class D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allows you to tune the bass for the desired level for the music. General Features: Rockford Fosgate Prime R2-500X1 RMS Power Rating: 4 ohms: 300 watts x 1 chan. 2 ohms: 500 watts x 1 chan. Total power output: 500 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeat able Auto Turn-On Circuit Features C.L.E.A.N. Set-up Variable Input Gain adjustment level R.L.C. Remote Level Control Variable Infrasonic Filter Continuously Variable On Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Full Range Class D Rollback Protection Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers Input sensitivity: Low-Level: 150 mV - 4 V High-Level: 450 mV - 12 V Frequency Response: 20 Hz - 250 Hz Total Harmonic Distortion (THD): >1% Crossover Controls Low-Pass: 50 Hz - 250 Hz Sub Infrasonic: 15 Hz - 40 Hz Recommended Fuse Rating: 80A 4 gauge power and ground wiring is recommended for installation Dimensions: "1.9" x "6.8" x "8.5" Authorized Internet Dealer 1 Year Manufacturer's Warranty What is in the R2-500X1 package: Rockford Fosgate R2-500X1 owner's manual Mono subwoofer amplifier Wired Remote Level Control module 16' Remote cable (RJ-25 connector on both ends) One 7" Speaker input harnesses 3mm Allen Hex key Four 3/4" Screws Two 1/2" Screws 5 Flat washers 1 Nut Installation and Operation Instructions Certificate of Performance Rockford Fosgate contact information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca

Rockford Fosgate M2-500X1 Marine 500-Watt Mono Amplifier Designed to withstand the elements, the M2-500X1 Element Ready amplifier is a 500-watt, class-D model, capable of operating at 4Ω or 2Ω mono. This amplifier is extremely efficient because of its class D technology which reduces demand on the electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allow you to tune the bass for the desired level for the music. General Features: mono marine subwoofer amplifier 300 watts RMS x 1 at 4 ohms 500 watts RMS x 1 at 2 ohms CTA-2006 compliant Class-D amplifier design wired remote included variable low-pass filter (50-250 Hz, 12 dB/octave) variable subsonic filter (15-40 Hz, 12 dB/octave) variable bass boost (0-18 dB at 45 Hz) marine features: Element Ready™ chassis and conformal-coated PC boards UV stable powder-coated cast aluminum heatsink zinc nickel-plated marine-grade brass connection terminals C.L.E.A.N. gain setup system includes clip lights auto remote turn-on preamp and speaker-level inputs preamp outputs wiring, fuse, and hardware not included with amplifier 4-gauge power and ground leads and an 80-amp fuse recommended dimensions: 8-1/2"W x 1-15/16"H x 6-13/16"D warranty: 2 years The M2-500X1 Element Ready Marine mono amplifier with 500 Watts RMS is packed with all the power and performance you have come to expect from Rockford Fosgate (Dimensions: 1.9" x 6.8" x 8.5") Class D technology makes this amp extremely efficient by reducing demand on the vehicles electrical system (RMS Power: 300 Watts x 1 @ 4Ω OR 500 Watts x 1 @ 2Ω) Built for the marine environment, this Element Ready amp features UV resistant protection, conformal coated circuit board, stainless steel mounting hardware, and marine-grade terminal connections to ensure long-lasting outdoor use Featuring C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass Famous Rockford Fosgate build quality with a full 2-year warranty when purchased from an authorized Rockford Fosgate reseller What is in the box: Mono marine amplifier Remote Punch Level Control module 16.5' Remote Punch Level Control cable (RJ-25 connector on both ends) 7" Speaker input harness 3mm Hex key Four 3/4" Screws Two 1/2" Screws 5 Flat washers 1 Nut Installation and Operation Instructions (English/ French/ Spanish/ German/ Italian) Certificate of Performance Verification Rockford Fosgate contacts information Rockford Fosgate M2-500X1 owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate PM100X1K Punch Marine 100 Watt Full-Range Mono Amplifier (Pair) The Punch Marine PM100X1 is a pair of 100-Watt full range dynamic power mono amplifiers that don’t need a power wire, is extremely compact in size, but big on power! The PM100X1 uses our patent-pending BTL technology that utilizes the speaker output of the radio to not only provide the audio signal it needs, but also the power that runs the unit. With no more load to the radio than a standard 2 or 4-ohm speaker, this design allows the amp to be connected to a 20-Watt output radio and produce up to 100 Watts dynamically! The small footprint of the PM100X1K amplifier allows it to be installed virtually anywhere along the speaker signal pathway from behind the radio to the door itself. This design makes the amplifier ideal for OEM or aftermarket as they can be hidden in the dash or doors of the vehicle. It is also IP67 water intrusion rated so it is also built to withstand the elements in motorcycle, boat, and motorsport applications. General Features: two compact mono amplifiers 60 watts RMS x 1 at 4 ohms (100 watts RMS x 1 at 2 ohms) CEA-2006 compliant patent-pending BTL "Freeload" technology requires no separate positive power lead connects to speaker wiring and chassis ground selectable high-pass filter (60, 80, or 100 Hz at 12 dB/octave) input impedance switch for low-impedance-capable receivers rubber switch cover IPX6 water intrusion rated dimensions: 3"W x 1-5/16"H x 3-15/16"D warranty: 2 years Patented BTL powered "Freeload" Technology Uses Stored Energy from BTL Amplifier to Produce Dynamic Power of Over 100 Watts High Level Turn On Pig Tail Connectivity for Easy Installation Sold in pairs (left/right) Harvests both B+ and Audio Signal from Standard Head Unit Speaker Outputs Optional B+ Connection for Non-Standard Speaker Outputs Short Circuit & Over Voltage Protection Extruded Aluminum Heat Sink and Thermal Protection Discrete surface mount technology Small Stealth Package that Allows for Anywhere Installation Selectable 4 and 2 Ohm Play Current Limited to Protect Head Unit for Both 4 Ohm and 2 Ohm Configurations Muted turn-on. The PM100X1K is a pair (left/right) of 100-Watt dynamic power mono amplifiers using DC and AC voltages present on existing radio speaker outputs This compact amplifier (1.3” x 3.0” x 3.9) is small but big on power (RMS Power Output: 60 x 1 @ 4-Ohm or 100 x 1 @ 2-Ohm) The versatile design can be used on a factory system using 2-Ohm or 4-Ohm factory or aftermarket speakers. The PM100X1K is also IPX6 rated so it can withstand the elements in mobile, motorsport, and marine applications High Level Turn on with selectable 60, 80, and 100 Hz Selectable 12dB/Oct HP Butterworth Crossover, featuring pigtail connectivity in a small stealth package allows for easy anywhere installation Famous Rockford Fosgate build quality ensures it will handle everything you throw at it! Full 2-year parts and labor warranty when purchased from an authorized Rockford Fosgate reseller What is in the box: The PM100X1K package contains two separately boxed PM100x1 mono amplifiers. Each amplifier box includes: Mono amplifier with attached 7.75" pigtail 12" Input/Output/Ground harness (16 AWG wires) 12" Power wire (16 AWG) 2 Self-tapping screws (3/4" length) Certificate of Performance Verification Rockford Fosgate PM100X1 owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca

Rockford Fosgate Punch P500X1BD 500W RMS Punch Series Monoblock Class D Car Power Amplifier + Absolute KIT4 Amp Kit The Punch P500X1bd is a mono amplifier capable of 500 Watts into a 1-Ohm load. The Class-BD technology produces bass more efficiently over traditional amps, and its frequency response allows it to be optimized for subwoofers. General Features: Punch BD Series Monoblock Class BD Car Amplifier RMS Power Rating: 4 ohms: 150 watts x 1 chan. 2 ohms: 300 watts x 1 chan. 1 ohm: 500 watts x 1 chan. CEA-2006 compliant amplifier MOSFET power supply Muted turn-on. Cast aluminum heatsink. 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protect indicators. Nickel-plated captive C-clamp terminals. Ultra-efficient Class BD circuitry to maximize amplifier power efficiency. On-board differential inputs eliminate noise picked up by the signal cable. Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately) MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span. Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances. Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low. DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowers the operating temperature and potential for noise-like circuit boards designed by aerospace manufacturers. Input sensitivity: 150mV - 12V On-board Punch EQ with +18dB boost @ 45Hz. Variable low-pass filter: 50-250 Hz Selectable infrasonic filter: off / 28 Hz Frequency response: 20 - 250 Hz Total Harmonic Distortion: <1.0% Dimensions: 11"L x 7-3/4"W x 2-3/8"H 8 AWG to 18 AWG speaker wire output terminals Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the P500X1bd box: Mono subwoofer amplifier Four 1-1/2" Self-tapping screws 2.5mm Allen wrench Quick setup instructions Certificate of Performance P500X1bd owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Punch P500X1BD 500W RMS Punch Series Monoblock Class D Car Power Amplifier The Punch P500X1bd is a mono amplifier capable of 500 Watts into a 1-Ohm load. The Class-BD technology produces bass more efficiently over traditional amps, and its frequency response allows it to be optimized for subwoofers. General Features Punch BD Series Monoblock Class BD Car Amplifier RMS Power Rating: 4 ohms: 150 watts x 1 chan. 2 ohms: 300 watts x 1 chan. 1 ohm: 500 watts x 1 chan. CEA-2006 compliant amplifier MOSFET power supply Muted turn-on. Cast aluminum heatsink. 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protect indicators. Nickel-plated captive C-clamp terminals. Ultra-efficient Class BD circuitry to maximize amplifier power efficiency. On-board differential inputs eliminate noise picked up by the signal cable. Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately) MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span. Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances. Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low. DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowering the operating temperature and potential for noise-like circuit boards designed by aerospace manufacturers. Input sensitivity: 150mV - 12V On-board Punch EQ with +18dB boost @ 45Hz. Variable low-pass filter: 50-250 Hz Selectable infrasonic filter: off / 28 Hz Frequency response: 20 - 250 Hz Total Harmonic Distortion: <1.0% Dimensions: 11"L x 7-3/4"W x 2-3/8"H 8 AWG to 18 AWG speaker wire output terminals Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the P500X1bd box: Mono subwoofer amplifier Four 1-1/2" Self-tapping screws 2.5mm Allen wrench Quick setup instructions Certificate of Performance P500X1bd owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Punch P500X1BD 500W RMS Punch Series Monoblock Class D Car Power Amplifier The Punch P500X1bd is a mono amplifier capable of 500 Watts into a 1-Ohm load. The Class-BD technology produces bass more efficiently over traditional amps, and its frequency response allows it to be optimized for subwoofers. General Features Punch BD Series Monoblock Class BD Car Amplifier RMS Power Rating: 4 ohms: 150 watts x 1 chan. 2 ohms: 300 watts x 1 chan. 1 ohm: 500 watts x 1 chan. CEA-2006 compliant amplifier MOSFET power supply Muted turn-on. Cast aluminum heatsink. 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protect indicators. Nickel-plated captive C-clamp terminals. Ultra-efficient Class BD circuitry to maximize amplifier power efficiency. On-board differential inputs eliminate noise picked up by the signal cable. MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span. Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances. Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low. DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowers the operating temperature and potential for noise-like circuit boards designed by aerospace manufacturers. Input sensitivity: 150mV - 12V On-board Punch EQ with +18dB boost @ 45Hz. Variable low-pass filter: 50-250 Hz Selectable infrasonic filter: off / 28 Hz Frequency response: 20 - 250 Hz Total Harmonic Distortion: <1.0% Dimensions: 11"L x 7-3/4"W x 2-3/8"H 8 AWG to 18 AWG speaker wire output terminals Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the P500X1bd : Mono subwoofer amplifier Four 1-1/2" Self-tapping screws 2.5mm Allen wrench Quick setup instructions Certificate of Performance P500X1bd owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate T750X1bd 750W Power Series Ultra-Compact Class-BD Monoblock Amplifier The Power T750X1bd 750 Watt mono, the ultra-compact amplifier is built on Rockford Fosgate’s patented Class bd technology platform. This design creates a highly efficient design that reduces the electrical impact on the vehicle charging system using the efficient Class D technology while maintaining fidelity, combining it with Class B topology. Flexible vehicle integration is achieved via a configurable input harness with Molex-style connectivity that accepts both RCA and speaker level signals, while our differential input circuitry eliminates signal noise from entering the amplifier resulting in a clean audio signal. The amplifier also has integrated auto turn-on capabilities when using speaker-level input signals. It converts its remote input terminal to an output that can turn on additional amplifiers. This can eliminate the need to source a separate remote turn-on signal for the amplifier from the vehicle. Top-mounted controls allow easy access to the built-in low-pass crossover: patented Punch EQ boost circuit and our patented C.L.E.A.N. input/output clip detection circuits. The 3-stage thermal lock extrusion with dual fan forced induction keeps everything cool. In contrast, our real-time thermal/protection schemes safeguard the amplifier during overheating or short-circuit conditions. The unit is also compatible with our Punch PLC2 remote level controller and is ideal for installations requiring a compact amplifier that can produce high-output power. General Features: Rockford Fosgate T750X1bd Class-BD 1-Ohm Stable Monoblock Amplifier RMS Power Rating: 4 ohms: 500 watts x 1 chan. 2 ohms: 750 watts x 1 chan. 1 ohm: 750 watts x 1 chan. Total power output: 750 watts CEA-2006 Compliant Amplifier Perfect for hybrid, electric, small cars, trucks, motorcycles, and side-by-side UTVs Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) LED power (blue), protect (red), input clip (red), and output clip (blue/red) indicators C.L.E.A.N. input/output clip detection and indicator LEDs Top-mounted controls Built-in Punch EQ circuit Real-time thermal sensing with Rollback technology Remote-Out feature when using high-level inputs Rockford Fosgate proprietary low impedance Constant Power Mono channel operation Speaker-level (high-level) inputs with auto turn-on 3-way protection circuitry (thermal, overload, and speaker short protection) Dual extruded heat sinks Dual fan cooled Input sensitivity: 150mV to 12V Speaker wire gauge: 10 AWG Frequency Response: 20 - 230Hz Total Harmonic Distortion (THD): <1.0% Variable low-pass filter: 50 - 250 Hz, 12 dB/octave Variable Bass Boost: 0 to +18 dB bass boost at 45 Hz Recommended Fuse: 100A (not included) Dimensions: 4.3"W x 8.3"L x 1.6"H Authorized Internet Dealer 1-year Manufacturer's Warranty ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Prime R2-750X5 750W Prime Series 5-Channel Full Range Class D Amplifier Primed for performance, the R2-750X5 is a 750 watt rated, full-range class-D amplifier capable of operating at 4Ω or 2Ω stereo with a mono subwoofer channel that can be run at 4Ω or 2Ω. The front/rear stereo channels can also be run at a 4Ω bridged/mono load. This amplifier is extremely efficient because of its Class-D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. supply that generates more dynamic power as voltage increases, and an integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. Rockford Fosgate's R2 amplifiers are the building blocks for great audio systems, powerful enough to even DRIVE our Punch speakers and subwoofers. They have undergone an amazing upgrade by packing them with the latest features at an incredible value. Best of all, they are designed and engineered here in Tempe, Arizona. General Features: Rockford Fosgate Prime R2-750X2 Class-D Full-Range 5-Channel Amplifier RMS Power Rating: 4 ohms: 50 watts x 4 Channel RMS Power Rating: 2 ohms: 100 watts x 4 Channel Bridged RMS Power Rating 4 ohms: 200 watts x 2 Channel Sub Channel: 4 ohms: 200 x 1 Channel Sub Channel: 2 ohms: 350 x 1 Channel Total power output: 600 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeat able Auto Turn on Circuit Features C.L.E.A.N. Set-up 2/4/5 Channel Input Selection Switch L.C. Remote Level Control Variable Infrasonic Filter Front, Rear, and Sub Variable Input Gain adjustment level Continuously Variable on-Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Full Range Class D Rollback Protection Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers Frequency Response: 20 Hz - 20 kHz Total Harmonic Distortion (THD): >1% Crossover Controls: Variable high-pass filter: 50 - 250 Hz, 24 dB/octave Crossover Controls: Variable low-pass filter: 50 - 250 Hz, 24 dB/octave Sub Low-Pass: 50 Hz - 250 Hz Sub Infrasonic: 15 Hz - 40 Hz Fuse Rating: 120A 4-gauge power and ground wiring are recommended for installation. Dimensions: 1.9"x6.8"x11.2" Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the box: 5-Channel amplifier Wired Remote Level Control module 16' Remote cable (RJ-25 connector on both ends) Three 7" Speaker input harnesses 3mm Allen Hex key Four 3/4" Screws Two 1/2" Screws 5 Flat washers 1 Nut Installation and Operation Instructions (English/ French/ Spanish/ German/ Italian) Certificate of Performance Rockford Fosgate contacts information Rockford Fosgate R2-750X5 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Rockford Fosgate Punch P300X2 300W RMS Punch Series 2-Channel Stereo Class AB Car Power Amplifier The Punch P300X2 is a 2-channel stereo amplifier capable of producing 150 Watts into each channel at 2-Ohms. The P300X2 amplifier is great to drive a pair of coaxial speakers, component speakers, or a single subwoofer. The amplifier can also be run in stereo/mono mode simultaneously when using passive crossovers (not supplied) on all speakers. With proven PUNCH technology, the P300X2 delivers real Rockford Fosgate power from a small design and is flexible to accommodate any moderately sized system. General Features: Punch Series 2-Channel Class AB Car Amplifier RMS Power Rating: 4 ohms: 100 watts x 2 Channel 2 ohms: 150 watts x 2 Channel Bridged, 4 ohms: 300 watts x 1 chan. CEA-2006 compliant amplifier Features C.L.E.A.N. Set-up with input/output clip detection and indicator LEDs MOSFET power supply Muted turn on Cast aluminum heatsink 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protect indicators Nickel-plated captive C-clamp terminals Ultra-efficient Class BD circuitry to maximize amplifier power efficiency On-board differential inputs eliminate noise picked up by the signal cable Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately) MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowers the operating temperature and potential for noise - similar to circuit boards designed by aerospace manufacturers Input sensitivity: 150mV - 12V What is in the box: 2-Channel amplifier Four 1-1/2" Screws 5mm Allen wrench Quick setup instructions Certificate of Performance Rockford Fosgate Punch P300X2 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Rockford Fosgate Punch PBR300X2 300 Watts Punch Series Boosted Rail Compact 2-Channel Amplifier The Punch PBR300X2 is a 2-channel stereo amplifier capable of producing 150 Watts into each channel at 2-Ohms. The PBR300X2 amplifier is great to drive a pair of coaxial speakers, component speakers, or a single subwoofer. The amplifier can also be run in stereo/mono mode simultaneously when using passive crossovers (not supplied) on all speakers. With proven PUNCH technology, the PBR300X2 delivers real Rockford Fosgate power from a small design and is flexible to accommodate any moderately sized system. General Features: Punch Series BR Monoblock Car Amplifier RMS Power Rating @ 4 ohms: 100 watts x 2 channel RMS Power Rating @ 2 ohms: 150 watts x 2 channel 4 ohm Bridged: 300 watts x 1 chan. Features Rockford Fosgate Class-BR Topology CEA-2006 compliant amplifier Ultra-compact chassis MOSFET output stage Boosted Rail amp technology Convection cooling design Extruded aluminum heat sink Low-level RCA input connection High-level speaker input connection Detachable Compression Terminals 12dB / Octave Butterworth crossover Selectable crossover mode: LP/AP/HP LED power (blue) and protect (red) indicators Variable 4-6 volt hi-level DC offset voltage input turn-on control Features MEHSA3 (Maximum Efficiency Heat Sink Application - gen. 3) Perfect for smaller stealth installations Great for motorcycles and recreational vehicles Optional Remote Punch EQ provides 0dB to +18dB @ 45Hz 16 Gauge speaker wire output terminals 10-gauge OFC power and ground wiring are recommended for installation. 1-year Manufacturer's Warranty What is in the box: 2-Channel amplifier 6" Speaker output harness (Molex plug on one end and tinned bare wire on the other) 12" Input harness (Molex plug on one end and female stereo RCA jacks on the other) Quick setup instructions Certificate of Performance Rockford Fosgate Punch PBR300X2 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Rockford Fosgate PBR400X4D 400W Compact 4 Channel Punch Series Class D Amplifier 50 watts RMS x 4 designed for stereo front/rear systems that require little space. The BRT (Boosted Rail Technology) is an ultra-efficient design that generates 400 watts of power! The BRT also has a variable hi-level DC offset turn-on circuit for easy installation into any OEM system. Great for motorcycles and recreational vehicles. The Punch PBR400X4D is a 400 Watt full-range amp designed for compact systems. This efficient 4-channel amp packs a Punch in UTVs, motorcycles, and hybrid-electric vehicles without sucking a lot of juice from your electrical system. General Features: Rockford Fosgate PBR400X4D Class D 4-Channel Amplifier RMS Power Rating: 4 ohms 50 watts x 4 channel RMS Power Rating: 2 ohms 100 watts x 4 channel RMS Power Rating: 1 ohm 1200 watts x 1 channel RMS Power Rating: Bridged 4 ohms 200 watts x 2 channel Total power output: 400 watts CEA-2006 Compliant Amplifier Differential inputs with high-level auto turn-on feature C.L.E.A.N. input/output clip detection and indicator LEDs Selectable Fixed 12dB/Octave Butterworth Crossovers Discrete surface mount technology 4-channel operation Extruded aluminum heatsinks Compact design for stealth installation Frequency Response: 20 Hz to 20000 Hz Total Harmonic Distortion (THD): < 1.0% (100 Hz) Fuse Rating: 40A x 3 Dimensions: "4.25"W x "1.53"H x "6.75"D Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the PBR400X4D package: 4-Channel amplifier Two 15" high-level input harnesses Two 8" speaker-level output harnesses Setup disc (CD) Amplifier Quick Setup Certificate of Performance Verification sheet Class-BR Amplifier Installation Advisory sheet ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca

Rockford Fosgate R2-300X4 Prime Series 300 Watts 4-Channel Class D Amplifier  Primed for performance, the R2-300X4 is a 300-watt, full-range Class-D amplifier capable of operating at 4Ω or 2Ω stereo and 4Ω bridged/mono. This amplifier is extremely efficient because of its Class-D technology, which reduces the vehicle's electrical system demand. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. supply that generates more power as voltage increases. General Features: Rockford Fosgate Prime R2-300X4 Class-D Full-Range 4-Channel Amplifier 50 watts RMS x 4 at 4 ohms 75 watts RMS x 4 at 2 ohms 150 watts RMS x 2 bridged output at 4 ohms bridged mode Total power output: 3000 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeat able Auto Turn-On Circuit Features C.L.E.A.N. Set-up 2/4 Channel Input Selection Switch Front and Rear Variable Input Gain adjustment level Continuously Variable on-Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Full Range Class D Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers 1 Year Warranty Low level: 125mV-5V High level: 250mV-10V Frequency Response: 20 Hz - 20 kHz Hz Total Harmonic Distortion (THD): <1% Variable high-pass filter: 50 - 250 Hz, 24 dB/octave Variable low-pass filter: 50 - 250 Hz, 24 dB/octave Recommended Fuse Rating: 60A Dimensions: 1.9" x "6.8" x "10.1" Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the R2-300X4 package: R2-300X4 Owner's Manual 4-Channel amplifier Two 7" Speaker input harnesses 3mm Allen Hex key Four 3/4" Screws 4 Flat washers Installation and Operation Instructions Certificate of Performance Rockford Fosgate contact information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate R2-250X1 Prime Series mono subwoofer amplifier 250-Watt Monoblock Amplifier Rockford Fosgate's R2 amplifiers are the building blocks for great audio systems, powerful enough even to DRIVE our Punch speakers and subwoofers. They have undergone an amazing upgrade by packing them with the latest features at incredible value. Best of all, they are designed and engineered here in Tempe, Arizona. Primed for performance, the R2-250X1 is a 250-watt, class-D amplifier capable of operating at 4Ω or 2Ω mono. This amplifier is extremely efficient because of its class-D technology, which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. Perfect for subwoofers, a variable infrasonic filter, and remote level control allows you to tune the bass for the desired level of the music. General Features: Rockford Fosgate Prime R2-250X1 Class-D Full-Range Monoblock Amplifier 320 watts x 1 channel @ 4 Ohms RMS Power 600 watts x 2 channel @ 2 Ohms RMS Power Total power output: 250 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeat able Auto Turn-On Circuit Features C.L.E.A.N. Set-up Variable Input Gain adjustment level R.L.C. Remote Level Control Variable Infrasonic Filter Continuously Variable On Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Full-Range, Class D Rollback Protection Input Sensitivity: Low-Level: 150 mV - 4 V High-Level: 450 mV - 12 V Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers Frequency Response: 20 Hz - 250 Hz Total Harmonic Distortion (THD): >1% Crossover Controls: Low-Pass: 50 Hz - 250 Hz Sub Infrasonic: 15 Hz - 40 Hz Recommended Fuse Rating: 50A Dimensions: "1.9" x "6.8" x "8.1" Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the R2S-1X12 package: R2S-1X12 owner's manual Sealed enclosure loaded with one 12" woofer 2 Mounting brackets Four 3/4" Self-tapping screws Installation and operation instructions

2 Rockford Fosgate PBR400X4D 400W Compact 4 Channel Punch Series Class D Amplifier 50 watts RMS x 4 designed for stereo front/rear systems that require little space. The BRT (Boosted Rail Technology) is an ultra-efficient design that generates 400 watts of power! The BRT also has a variable hi-level DC offset turn-on circuit for easy installation into any OEM system. Great for motorcycles and recreational vehicles. The Punch PBR400X4D is a 400 Watt full-range amp designed for compact systems. This efficient 4-channel amp packs a Punch in UTVs, motorcycles, and hybrid-electric vehicles without sucking a lot of juice from your electrical system. General Features: Rockford Fosgate PBR400X4D Class D 4-Channel Amplifier RMS Power Rating: 4 ohms 50 watts x 4 channel RMS Power Rating: 2 ohms 100 watts x 4 channel RMS Power Rating: 1 ohm 1200 watts x 1 channel RMS Power Rating: Bridged 4 ohms 200 watts x 2 channel Total power output: 400 watts CEA-2006 Compliant Amplifier Differential inputs with high-level auto turn-on feature C.L.E.A.N. input/output clip detection and indicator LEDs Selectable Fixed 12dB/Octave Butterworth Crossovers Discrete surface mount technology 4-channel operation Extruded aluminum heatsinks Compact design for stealth installation Frequency Response: 20 Hz to 20000 Hz Total Harmonic Distortion (THD): < 1.0% (100 Hz) Fuse Rating: 40A x 3 Dimensions: "4.25"W x "1.53"H x "6.75"D Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the PBR400X4D package: 4-Channel amplifier Two 15" high-level input harnesses Two 8" speaker-level output harnesses Setup disc (CD) Amplifier Quick Setup Certificate of Performance Verification sheet Class-BR Amplifier Installation Advisory sheet ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca