Rockford Fosgate Amplifiers (77)

Rockford Fosgate Prime R1200-1D 1200W RMS Prime Series Class-D Monoblock 1-Ohm Stable Amplifier The PRIME R1200-1D is an ultra-efficient mono amplifier for cars and trucks that can produce 1,200 Watts into a 1-Ohm load without taxing the electrical system. The frequency response of the R1200-1D is optimized exclusively for use with subwoofers. The Prime R1200-1D subwoofer amplifier offers high efficiency through the implementation of its Class-D circuitry while delivering rich, full bass to any system. This car amplifier is optimized for subwoofers with the implementation of an infrasonic filter to keep those ultra-low (inaudible) bass notes from damaging your subwoofer system. Match with a 4-channel stereo amplifier for your mids/highs and you'll have a Rockford Fosgate system that any Car Audio Fanatic will envy. General Features: Rockford Fosgate Prime Series R1200-1D Class-D 1-Ohm Stable Monoblock Amplifier RMS Power Rating: 4 ohms: 400 watts x 1 channel RMS Power Rating: 2 ohms: 800 watts x 1 channel RMS Power Rating: 1 ohm: 1200 watts x 1 channel CEA-2006 Compliant Amplifier Pulse Width Modulated MOSFET power supply Wired remote bass level control included LED power (green) and protect (red) indicators Soft start turn-on Nickel-plated RCA level inputs Nickel-plated screw terminals Preamp RCA outputs to daisy chain multiple amps 3-way protection circuitry (thermal, overload, and speaker short protection) Heavy-duty aluminum alloy heat-sink for extreme heat dissipation Input sensitivity: 150mV - 4V Frequency Response: 20 - 250Hz Total Harmonic Distortion (THD): <1.0% Signal to Noise Ratio: 100dB Variable low-pass filter: 50 - 250 Hz, 12 dB/octave Subsonic (infrasonic) filter: 15 - 40 Hz , 12 dB/octave Variable Bass Boost: 0 to +18 dB bass boost at 45 Hz Fuse Rating: 150A x 1 (recommended, not included) 12 AWG speaker wire gauge outputs 4 gauge power and ground wiring is recommended for installation Weight: 7.825 lbs Dimensions: 11.06"W x 6.77"L x 1.97"H Also Found As Prime 1200 Watt, R12001D, R1200, R12001 Authorized Internet Dealer 1-year Manufacturer's Warranty ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca

Rockford Fosgate Prime R2-500X1 500W Prime Series Monoblock Subwoofer Class D Amplifier Primed for performance, the R2-500X1 amplifier is a 500 watt, class-D, capable of operating at 4Ω or 2Ω mono. This amplifier is extremely efficient because of its class D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allows you to tune the bass for the desired level for the music. General Features: Rockford Fosgate Prime R2-500X1 RMS Power Rating: 4 ohms: 300 watts x 1 chan. 2 ohms: 500 watts x 1 chan. Total power output: 500 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeat able Auto Turn-On Circuit Features C.L.E.A.N. Set-up Variable Input Gain adjustment level R.L.C. Remote Level Control Variable Infrasonic Filter Continuously Variable On Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Full Range Class D Rollback Protection Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers Input sensitivity: Low-Level: 150 mV - 4 V High-Level: 450 mV - 12 V Frequency Response: 20 Hz - 250 Hz Total Harmonic Distortion (THD): >1% Crossover Controls Low-Pass: 50 Hz - 250 Hz Sub Infrasonic: 15 Hz - 40 Hz Recommended Fuse Rating: 80A 4 gauge power and ground wiring is recommended for installation Dimensions: "1.9" x "6.8" x "8.5" Authorized Internet Dealer 1 Year Manufacturer's Warranty What is in the R2-500X1 package: Rockford Fosgate R2-500X1 owner's manual Mono subwoofer amplifier Wired Remote Level Control module 16' Remote cable (RJ-25 connector on both ends) One 7" Speaker input harnesses 3mm Allen Hex key Four 3/4" Screws Two 1/2" Screws 5 Flat washers 1 Nut Installation and Operation Instructions Certificate of Performance Rockford Fosgate contact information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca

Rockford Fosgate T750x1BD Power 500 Watts Watt Class-AD Mono Channel Amplifier + Absolute KIT4 4 Gauge Amplifier Installation Wiring Kit The Power T750X1bd is an ultra-compact, Class bd 750-watt mono amplifier. It features a high-level auto turn-on, the CLEAN circuit with input/output clip detection, top-mounted controls, and dual fan forced induction cooling. Additionally, it has our patented Punch EQ circuit built in and Differential inputs with auto turn-on capabilities. Perfect for hybrid, electric, small cars, trucks, motorcycles, and side-by-side UTVs. General Features: Rockford Fosgate T750X1bd Class-BD 1-Ohm Stable Monoblock Amplifier RMS Power Rating: 4 ohms: 500 watts x 1 chan. 2 ohms: 750 watts x 1 chan. 1 ohm: 750 watts x 1 chan. Total power output: 750 watts CEA-2006 Compliant Amplifier Perfect for hybrid, electric, small cars, trucks, motorcycles, and side-by-side UTVs Optional remote Punch Level Control (PLC2 ready (w/ input clip indicator) LED power (blue), protect (red), input clip (red), and output clip (blue/red) indicators L.E.A.N. input/output clip detection and indicator LEDs Top-mounted controls Built-in Punch EQ circuit Real-time thermal sensing with Rollback technology Remote-Out feature when using high-level inputs Rockford Fosgate proprietary low impedance Constant Power Mono channel operation Speaker-level (high-level) inputs with auto turn-on 3-way protection circuitry (thermal, overload, and speaker short protection) Dual extruded heat sinks Dual fan cooled Input sensitivity: 150mV to 12V Speaker wire gauge: 10 AWG Frequency Response: 20 - 230Hz Total Harmonic Distortion (THD): <1.0% Variable low-pass filter: 50 - 250 Hz, 12 dB/octave Variable Bass Boost: 0 to +18 dB bass boost at 45 Hz Recommended Fuse: 100A (not included) 2-Year Warranty Absolute KIT 4 Gauge Amp Kit 17 ft. of red 4 AWG high current power cable 3 ft. of black 4 AWG ground cable 15 ft. of RCA triple shielded interconnect audio cable with built-in remote wire 20 ft. of 12 AWG OFC Speaker cable 20 ft. of 16 AWG remote turn-on wire 6 ft. of split loom tubing 1 Gold-plated 80 AMP AGU fuse 1 4 AWG gold ring terminal 750W Power Series Ultra-Compact Class-BD Monoblock Amplifier 500 Watts RMS x 1 @ 4 ohms 750 Watts RMS x 1 @ 2 ohms 750 Watts RMS x 1 @ 1 ohm Complete 4 Gauge Amplifier Kit For Use in Any Car, Truck, RV, or Boat ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate T400X2ad Power Series 400 Watt Class-AD 2-Channel Amplifier Amp +Absolute KIT0 0 Gauge Amp Kit The Power T400X2ad is an ultra-compact, high-efficiency 400-watt stereo amplifier. Features multi-impedance Constant Power, input/output clip detection, top-mounted controls, and dual fan forced induction cooling. Perfect for hybrid, electric, small cars, trucks, motorcycles, and side-by-side UTVs. General Features: Rockford Fosgate proprietary Class AD technology 4/2 Ohm muti-impedance Constant Power Rated Power (RMS Continuous Power): 200 Watts x 2 @ 4-Ohm  Rated Power (RMS Continuous Power): 200 Watts x 2 @ 2-Ohm  Rated Power (RMS Continuous Power): 400 Watts x 1 @ 4-Ohm Bridged Differential inputs with high-level auto turn-on feature 8 AWG power/ground connectors w/ upgraded RCA connectors  Remote-out feature when using high-level inputs 4 Ohm bridged capable 2013 PLC2 remote ready C.L.E.A.N. input/output clip detection and indicator LEDs Top-mounted controls Dual fan-cooled Real-time thermal sensing Dual extruded heat sinks Discrete surface mount technology 2-Year Warranty ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca..

Rockford Fosgate T400X2ad Power Series 400 Watt Class-AD 2-Channel Amplifier Amp +Absolute KIT4 4 Gauge Amp Kit The Power T400X2ad is an ultra-compact, high-efficiency 400-watt stereo amplifier. Features multi-impedance Constant Power, input/output clip detection, top-mounted controls, and dual fan forced induction cooling. Perfect for hybrid, electric, small cars, trucks, motorcycles, and side-by-side UTVs. General Features: Rockford Fosgate proprietary Class AD technology 4/2 Ohm muti-impedance Constant Power Rated Power (RMS Continuous Power): 200 Watts x 2 @ 4-Ohm  Rated Power (RMS Continuous Power): 200 Watts x 2 @ 2-Ohm  Rated Power (RMS Continuous Power): 400 Watts x 1 @ 4-Ohm Bridged Differential inputs with high-level auto turn-on feature 8 AWG power/ground connectors w/ upgraded RCA connectors  Remote-out feature when using high-level inputs 4 Ohm bridged capable 2013 PLC2 remote ready C.L.E.A.N. input/output clip detection and indicator LEDs Top-mounted controls Dual fan-cooled Real-time thermal sensing Dual extruded heat sinks Discrete surface mount technology 2-Year Warranty ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate T400X2ad Power Series 400 Watt Class-AD 2-Channel Amplifier Amp +Absolute KIT8 8 Gauge Amp Kit The Power T400X2ad is an ultra-compact, high-efficiency 400-watt stereo amplifier. Features multi-impedance Constant Power, input/output clip detection, top-mounted controls, and dual fan forced induction cooling. Perfect for hybrid, electric, small cars, trucks, motorcycles, and side-by-side UTVs. General Features: Rockford Fosgate proprietary Class AD technology 4/2 Ohm muti-impedance Constant Power Rated Power (RMS Continuous Power): 200 Watts x 2 @ 4-Ohm  Rated Power (RMS Continuous Power): 200 Watts x 2 @ 2-Ohm  Rated Power (RMS Continuous Power): 400 Watts x 1 @ 4-Ohm Bridged Differential inputs with high-level auto turn-on feature 8 AWG power/ground connectors w/ upgraded RCA connectors  Remote-out feature when using high-level inputs 4 Ohm bridged capable 2013 PLC2 remote ready C.L.E.A.N. input/output clip detection and indicator LEDs Top-mounted controls Dual fan-cooled Real-time thermal sensing Dual extruded heat sinks Discrete surface mount technology 2-Year Warranty Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate T400X2ad Power Series 400 Watt Class-AD 2-Channel Amplifier Amp + Rockford Fosgate RFK8 Amp Kit The Power T400X2ad is an ultra-compact, high-efficiency 400-watt stereo amplifier. Features multi-impedance Constant Power, input/output clip detection, top-mounted controls, and dual fan forced induction cooling. Perfect for hybrid, electric, small cars, trucks, motorcycles, and side-by-side UTVs. General Features: Rockford Fosgate proprietary Class AD technology 4/2 Ohm muti-impedance Constant Power Rated Power (RMS Continuous Power): 200 Watts x 2 @ 4-Ohm  Rated Power (RMS Continuous Power): 200 Watts x 2 @ 2-Ohm  Rated Power (RMS Continuous Power): 400 Watts x 1 @ 4-Ohm Bridged Differential inputs with high-level auto turn-on feature 8 AWG power/ground connectors w/ upgraded RCA connectors  Remote-out feature when using high-level inputs 4 Ohm bridged capable 2013 PLC2 remote ready C.L.E.A.N. input/output clip detection and indicator LEDs Top-mounted controls Dual fan-cooled Real-time thermal sensing Dual extruded heat sinks Discrete surface mount technology 2-Year Warranty ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate T400X2ad Power Series 400 Watt Class-AD 2-Channel Amplifier Amp The Power T400X2ad is an ultra-compact, high-efficiency 400-watt stereo amplifier. Features multi-impedance Constant Power, input/output clip detection, top-mounted controls, and dual fan forced induction cooling. Perfect for hybrid, electric, small cars, trucks, motorcycles, and side-by-side UTVs. General Features: Rockford Fosgate proprietary Class AD technology 4/2 Ohm muti-impedance Constant Power Rated Power (RMS Continuous Power): 200 Watts x 2 @ 4-Ohm  Rated Power (RMS Continuous Power): 200 Watts x 2 @ 2-Ohm  Rated Power (RMS Continuous Power): 400 Watts x 1 @ 4-Ohm Bridged Differential inputs with high-level auto turn-on feature 8 AWG power/ground connectors w/ upgraded RCA connectors  Remote-out feature when using high-level inputs 4 Ohm bridged capable 2013 PLC2 remote ready C.L.E.A.N. input/output clip detection and indicator LEDs Top-mounted controls Dual fan-cooled Real-time thermal sensing Dual extruded heat sinks Discrete surface mount technology 2-Year Warranty ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate T400X2ad Power 400 Watt Class-AD 2-Channel Amplifier Rockford Fosgate's Power Series T400X2ad 2-channel amplifier can send each of your speakers up to 200 watts RMS, or you can use this tiny powerpack to run a sub with up to 400 watts. A dual-fan forced air cooling system keeps this sturdy little amp from overheating, so it can play hard for a long, long time. Class AD: accurate and powerful Rockford Fosgate uses their proprietary Class AD amplifier technology, combining the high fidelity of a Class A system with the high efficiency of their special Class D technology, to bring you this ultra-efficient, high-output amplifier. In other words, this compact amp produces more power with less current draw from your vehicle's charging system than most other amps on the road today. Rockford Fosgate's high-tech solutions yield more power Power Series amplifiers actively monitor speaker performance using Rockford Fosgate's Constant Power technology. A speaker's impedance naturally fluctuates as it performs, fighting against your amp's output. So, just like your cruise control increases the engine's RPM to maintain your car's speed uphill, Constant Power maintains this amp's output by increasing its internal voltage and current flow when the speaker's impedance rises. This results in up to a 25% increase in the amp's total power output. T400X2ab control panel with clip lights Easy to set for optimum performance Rockford Fosgate's C.L.E.A.N. technology (Calibrated Level Eliminates Audible Noise) setup system ensures your music will sound as clean and powerful as possible. It works like this: first download the SET UP from Rockford Fosgate, then play the tone, adjust the receiver volume until a red clip light on the amp goes out, then turn the amp gain up until a blue light comes on. It's that simple — your amplifier will be perfectly set to match your receiver's output. When your receiver reaches maximum clean volume, you'll get maximum clean power from your Power amp. At quiet listening levels, you'll hear less background noise and more of your music. Clip lights If that blue light turns solid red while you're playing music, the amp's telling you that your source is distorting and you should turn it down, or risk damage to your gear. The optional PLC2 remote level control also doubles as a clip indicator, so you can see from the front seat if your music's clipping. Product highlights: 2-channel car amplifier 200 watts RMS x 2 at 2 to 4 ohms 400 watts RMS x 1 bridged output at 4 ohms (4-ohm stable in bridged mode) CEA-2006 compliant Features: Class AD amplifier design Constant Power technology maintains full output power despite impedance changes C.L.E.A.N. gain setup system includes clip lights and link to Rockford Fosgate's setup tones differential input circuitry helps eliminate hum dual-fan forced induction cooling variable high- and low-pass filters (50-250 Hz, 12 dB/octave) variable Punch EQ (bass/treble boost: 0-18 dB at 45 Hz, 0-14 dB at 12,500 Hz) optional PLC2 Punch Level Control wired remote with clip light available More Info: preamp and speaker-level inputs signal-sensing turn-on with speaker-level inputs eliminates the need for a remote turn-on lead 8-gauge power and ground leads and a 60-amp fuse recommended — wiring and hardware not included with amplifier no onboard fuses — when installing multiple amps in a system, an additional 60-amp in-line fuse between the distribution block and the amplifier is recommended 7"W x 1-15/8"H x 4-1/4"D warranty: 2 years (extends to 3 years when purchased with a Rockford Fosgate RFK8, RFK8i, or RFK4D amp wiring kit) ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

 2 Rockford Fosgate PLC2 Punch Remote Level Control w/Input Clip Indicator LED Show One Size Wired remote Punch Level Control for select 2013 and newer Punch and Power amplifiers. Remote Level Control offers remote level control of the amplifier. Once the onboard gain control is set, the PLC2 can attenuate (and not increase) the level from that point. Cable and mounting hardware included. For use with select 2013 and newer PUNCH and POWER amplifiers General Features: Rockford Fosgate PLC2 Punch Remote Level Control (Pair) wired remote level control and clip light Enhances onboard gain control Compatible with 2013 and newer Punch amplifiers Dual function LED (power/clipping) 20 Feet Wiring 0 20 dB Includes remote knob, cable, mounting clip, mounting screws For use with compact 2013 and newer PUNCH amplifiers. Product Condition: Brand New works with the following 2013-up Rockford Fosgate Punch amplifiers: P300X1, P400X1, P500X1bd, and P1000X1bd mono amps P300X2, P400X2, P500X2, and P1000X2 2-channel amps P600X4 4-channel amp P1000X5 5-channel amp 18' remote cable and mounting hardware included dimensions: 1-7/16"W x 1-1/4"H x 1-5/8"D (2-5/8"D with knob and cable) What is in the PLC2 box: Rockford Fosgate Punch Level Control remote module 18' remote cable with RJ-45 connectors on each end Mounting bracket Two 1/2" Mounting screws LED with attached 8" harness (used when mounting knob without its housing) Additional front panel Flat washer Nut PLC2 owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate 600W Punch Series 4-Channel Stereo Class AB Car Power Amplifier The Punch P600X4 is a 4-channel amplifier producing 150 Watts into all four channels at 2-Ohm. The P600X4 is perfect for a 4-way full-range system or a 3-way system having a front stage with subwoofers on the rear channels. The Punch P600X4 multi-channel amplifier is versatile to power any audio system configuration. The stealth top-mounted control panel not only provides a sleek finished look to the amp but also protects the vital controls. Our custom heat sink design uses high aluminum mass where it is needed most to maximize heat transfer from the output MOSFETS to the surrounding air, keeping the circuitry cool even under high power and output demand. General Features: Punch Series 4-Channel Class AB Car Amplifier RMS Power Rating: 4 ohms: 75 watts x 4 channel 2 ohms: 150 watts x 4 channel Bridged, 4 ohms: 300 watts x 2 channel MOSFET power supply Remote bass level input (remote level control sold separately) LED power, thermal, and protect indicators Tuned Bass EQ (0-18 dB bass boost at 45 Hz or 0-14 dB bass boost at 12 kHz depending on crossover selection) On-board differential inputs eliminate noise picked up by the signal cable 4/3/2 or Mono channel operation Integrated Trans ana technology simplifies the signal path of the amplifier allowing the signal to travel through the amplifier at a lower voltage. The result is greater reliability and exceptional sound quality RCA Pass-thru outputs MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowers the operating temperature and potential for noise - similar to circuit boards designed by aerospace manufacturers Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low Nickel-plated RCA level inputs Nickel-plated captive C-clamp terminals Variable high-pass filter (50-250 Hz, Butterworth, 12 dB/octave) Variable low-pass filter (50-250 Hz, Butterworth, 12 dB/octave) CEA-2006 compliant amplifier Frequency response: 20-20000 Hz Dimensions: 13-5/16"L x 7-3/4"W x 2-3/8"H 4-Channel amplifier Four 1-1/2" Self-tapping screws 2.5mm Allen wrench Quick setup instructions Certificate of Performance Rockford Fosgate Punch P600X4 owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Punch P600X4 600W Punch Series 4-Ch Stereo Class AB Car AMP The Punch P600X4 is a 4-channel amplifier producing 150 Watts into all four channels at 2-Ohm. The P600X4 is perfect for a 4-way full-range system or a 3-way system having a front stage with subwoofers on the rear channels. The Punch P600X4 multi-channel amplifier is versatile to power any audio system configuration. The stealth top-mounted control panel not only provides a sleek finished look to the amp but also protects the vital controls. Our custom heat sink design uses high aluminum mass where it is needed most to maximize heat transfer from the output MOSFETS to the surrounding air, keeping the circuitry cool even under high power and output demand. General Features: Punch Series 4-Channel Class AB Car Amplifier RMS Power Rating: 4 ohms: 75 watts x 4 channel 2 ohms: 150 watts x 4 channel Bridged, 4 ohms: 300 watts x 2 channel MOSFET power supply Remote bass level input (remote level control sold separately) LED power, thermal, and protect indicators Tuned Bass EQ (0-18 dB bass boost at 45 Hz or 0-14 dB bass boost at 12 kHz depending on crossover selection) On-board differential inputs eliminate noise picked up by the signal cable 4/3/2 or Mono channel operation Integrated Trans ana technology simplifies the signal path of the amplifier allowing the signal to travel through the amplifier at a lower voltage. The result is greater reliability and exceptional sound quality RCA Pass-thru outputs MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowers the operating temperature and potential for noise - similar to circuit boards designed by aerospace manufacturers Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low Nickel-plated RCA level inputs Nickel-plated captive C-clamp terminals Variable high-pass filter (50-250 Hz, Butterworth, 12 dB/octave) Variable low-pass filter (50-250 Hz, Butterworth, 12 dB/octave) CEA-2006 compliant amplifier Frequency response: 20-20000 Hz Dimensions: 13-5/16"L x 7-3/4"W x 2-3/8" 4-Channel amplifier Four 1-1/2" Self-tapping screws 2.5mm Allen wrench Quick setup instructions Certificate of Performance Rockford Fosgate Punch P600X4 owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate 600W Punch Series 4-Channel Stereo Class AB Car Power Amplifier The Punch P600X4 is a 4-channel amplifier producing 150 Watts into all four channels at 2-Ohm. The P600X4 is perfect for a 4-way full-range system or a 3-way system having a front stage with subwoofers on the rear channels. The Punch P600X4 multi-channel amplifier is versatile to power any audio system configuration. The stealth top-mounted control panel not only provides a sleek finished look to the amp but also protects the vital controls. Our custom heat sink design uses high aluminum mass where it is needed most to maximize heat transfer from the output MOSFETS to the surrounding air, keeping the circuitry cool even under high power and output demand. General Features: Punch Series 4-Channel Class AB Car Amplifier RMS Power Rating: 4 ohms: 75 watts x 4 channel 2 ohms: 150 watts x 4 channel Bridged, 4 ohms: 300 watts x 2 channel MOSFET power supply Remote bass level input (remote level control sold separately) LED power, thermal, and protect indicators Tuned Bass EQ (0-18 dB bass boost at 45 Hz or 0-14 dB bass boost at 12 kHz depending on crossover selection) On-board differential inputs eliminate noise picked up by the signal cable 4/3/2 or Mono channel operation Integrated Trans ana technology simplifies the signal path of the amplifier allowing the signal to travel through the amplifier at a lower voltage. The result is greater reliability and exceptional sound quality RCA Pass-thru outputs MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowers the operating temperature and potential for noise - similar to circuit boards designed by aerospace manufacturers Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low Nickel-plated RCA level inputs Nickel-plated captive C-clamp terminals Variable high-pass filter (50-250 Hz, Butterworth, 12 dB/octave) Variable low-pass filter (50-250 Hz, Butterworth, 12 dB/octave) CEA-2006 compliant amplifier Frequency response: 20-20000 Hz Dimensions: 13-5/16"L x 7-3/4"W x 2-3/8"H What is in the box: 4-Channel amplifier Four 1-1/2" Self-tapping screws 2.5mm Allen wrench Quick setup instructions Certificate of Performance Rockford Fosgate Punch P600X4 owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.ca.gov