Rockford Fosgate All Amplifiers (73)

Rockford Fosgate Prime R1200-1D 1200W RMS Prime Series Class-D Monoblock 1-Ohm Stable Amplifier The PRIME R1200-1D is an ultra-efficient mono amplifier for cars and trucks that can produce 1,200 Watts into a 1-Ohm load without taxing the electrical system. The frequency response of the R1200-1D is optimized exclusively for use with subwoofers. The Prime R1200-1D subwoofer amplifier offers high efficiency through the implementation of its Class-D circuitry while delivering rich, full bass to any system. This car amplifier is optimized for subwoofers with the implementation of an infrasonic filter to keep those ultra-low (inaudible) bass notes from damaging your subwoofer system. Match with a 4-channel stereo amplifier for your mids/highs and you'll have a Rockford Fosgate system that any Car Audio Fanatic will envy. General Features: Rockford Fosgate Prime Series R1200-1D Class-D 1-Ohm Stable Monoblock Amplifier RMS Power Rating: 4 ohms: 400 watts x 1 channel RMS Power Rating: 2 ohms: 800 watts x 1 channel RMS Power Rating: 1 ohm: 1200 watts x 1 channel CEA-2006 Compliant Amplifier Pulse Width Modulated MOSFET power supply Wired remote bass level control included LED power (green) and protect (red) indicators Soft start turn-on Nickel-plated RCA level inputs Nickel-plated screw terminals Preamp RCA outputs to daisy chain multiple amps 3-way protection circuitry (thermal, overload, and speaker short protection) Heavy-duty aluminum alloy heat-sink for extreme heat dissipation Input sensitivity: 150mV - 4V Frequency Response: 20 - 250Hz Total Harmonic Distortion (THD): <1.0% Signal to Noise Ratio: 100dB Variable low-pass filter: 50 - 250 Hz, 12 dB/octave Subsonic (infrasonic) filter: 15 - 40 Hz , 12 dB/octave Variable Bass Boost: 0 to +18 dB bass boost at 45 Hz Fuse Rating: 150A x 1 (recommended, not included) 12 AWG speaker wire gauge outputs 4 gauge power and ground wiring is recommended for installation Weight: 7.825 lbs Dimensions: 11.06"W x 6.77"L x 1.97"H Also Found As Prime 1200 Watt, R12001D, R1200, R12001 Authorized Internet Dealer 1-year Manufacturer's Warranty ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca

Rockford Fosgate R2-300X4 Prime Series 300 Watts 4-Channel Class D Amplifier Primed for performance, the R2-300X4 is a 300-watt, full-range Class-D amplifier capable of operating at 4Ω or 2Ω stereo and 4Ω bridged/mono. This amplifier is extremely efficient because of its Class-D technology, which reduces the vehicle's electrical system demand. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. supply that generates more power as voltage increases. General Features: Rockford Fosgate Prime R2-300X4 Class-D Full-Range 4-Channel Amplifier 50 watts RMS x 4 at 4 ohms 75 watts RMS x 4 at 2 ohms 150 watts RMS x 2 bridged output at 4 ohms bridged mode Total power output: 3000 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeat able Auto Turn-On Circuit Features C.L.E.A.N. Set-up 2/4 Channel Input Selection Switch Front and Rear Variable Input Gain adjustment level Continuously Variable on-Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Full Range Class D Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers 1 Year Warranty Low level: 125mV-5V High level: 250mV-10V Frequency Response: 20 Hz - 20 kHz Hz Total Harmonic Distortion (THD): <1% Variable high-pass filter: 50 - 250 Hz, 24 dB/octave Variable low-pass filter: 50 - 250 Hz, 24 dB/octave Recommended Fuse Rating: 60A Dimensions: 1.9" x "6.8" x "10.1" Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the R2-300X4 package: R2-300X4 Owner's Manual 4-Channel amplifier Two 7" Speaker input harnesses 3mm Allen Hex key Four 3/4" Screws 4 Flat washers Installation and Operation Instructions Certificate of Performance Rockford Fosgate contact information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate 600W Punch Series 4-Channel Stereo Class AB Car Power Amplifier The Punch P600X4 is a 4-channel amplifier producing 150 Watts into all four channels at 2-Ohm. The P600X4 is perfect for a 4-way full-range system or a 3-way system having a front stage with subwoofers on the rear channels. The Punch P600X4 multi-channel amplifier is versatile to power any audio system configuration. The stealth top-mounted control panel not only provides a sleek finished look to the amp but also protects the vital controls. Our custom heat sink design uses high aluminum mass where it is needed most to maximize heat transfer from the output MOSFETS to the surrounding air, keeping the circuitry cool even under high power and output demand. General Features: Punch Series 4-Channel Class AB Car Amplifier RMS Power Rating: 4 ohms: 75 watts x 4 channel 2 ohms: 150 watts x 4 channel Bridged, 4 ohms: 300 watts x 2 channel MOSFET power supply Remote bass level input (remote level control sold separately) LED power, thermal, and protect indicators Tuned Bass EQ (0-18 dB bass boost at 45 Hz or 0-14 dB bass boost at 12 kHz depending on crossover selection) On-board differential inputs eliminate noise picked up by the signal cable 4/3/2 or Mono channel operation Integrated Trans ana technology simplifies the signal path of the amplifier allowing the signal to travel through the amplifier at a lower voltage. The result is greater reliability and exceptional sound quality RCA Pass-thru outputs MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowers the operating temperature and potential for noise - similar to circuit boards designed by aerospace manufacturers Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low Nickel-plated RCA level inputs Nickel-plated captive C-clamp terminals Variable high-pass filter (50-250 Hz, Butterworth, 12 dB/octave) Variable low-pass filter (50-250 Hz, Butterworth, 12 dB/octave) CEA-2006 compliant amplifier Frequency response: 20-20000 Hz Dimensions: 13-5/16"L x 7-3/4"W x 2-3/8"H 4-Channel amplifier Four 1-1/2" Self-tapping screws 2.5mm Allen wrench Quick setup instructions Certificate of Performance Rockford Fosgate Punch P600X4 owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Punch P600X4 600W Punch Series 4-Ch Stereo Class AB Car AMP The Punch P600X4 is a 4-channel amplifier producing 150 Watts into all four channels at 2-Ohm. The P600X4 is perfect for a 4-way full-range system or a 3-way system having a front stage with subwoofers on the rear channels. The Punch P600X4 multi-channel amplifier is versatile to power any audio system configuration. The stealth top-mounted control panel not only provides a sleek finished look to the amp but also protects the vital controls. Our custom heat sink design uses high aluminum mass where it is needed most to maximize heat transfer from the output MOSFETS to the surrounding air, keeping the circuitry cool even under high power and output demand. General Features: Punch Series 4-Channel Class AB Car Amplifier RMS Power Rating: 4 ohms: 75 watts x 4 channel 2 ohms: 150 watts x 4 channel Bridged, 4 ohms: 300 watts x 2 channel MOSFET power supply Remote bass level input (remote level control sold separately) LED power, thermal, and protect indicators Tuned Bass EQ (0-18 dB bass boost at 45 Hz or 0-14 dB bass boost at 12 kHz depending on crossover selection) On-board differential inputs eliminate noise picked up by the signal cable 4/3/2 or Mono channel operation Integrated Trans ana technology simplifies the signal path of the amplifier allowing the signal to travel through the amplifier at a lower voltage. The result is greater reliability and exceptional sound quality RCA Pass-thru outputs MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowers the operating temperature and potential for noise - similar to circuit boards designed by aerospace manufacturers Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low Nickel-plated RCA level inputs Nickel-plated captive C-clamp terminals Variable high-pass filter (50-250 Hz, Butterworth, 12 dB/octave) Variable low-pass filter (50-250 Hz, Butterworth, 12 dB/octave) CEA-2006 compliant amplifier Frequency response: 20-20000 Hz Dimensions: 13-5/16"L x 7-3/4"W x 2-3/8" 4-Channel amplifier Four 1-1/2" Self-tapping screws 2.5mm Allen wrench Quick setup instructions Certificate of Performance Rockford Fosgate Punch P600X4 owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate 600W Punch Series 4-Channel Stereo Class AB Car Power Amplifier The Punch P600X4 is a 4-channel amplifier producing 150 Watts into all four channels at 2-Ohm. The P600X4 is perfect for a 4-way full-range system or a 3-way system having a front stage with subwoofers on the rear channels. The Punch P600X4 multi-channel amplifier is versatile to power any audio system configuration. The stealth top-mounted control panel not only provides a sleek finished look to the amp but also protects the vital controls. Our custom heat sink design uses high aluminum mass where it is needed most to maximize heat transfer from the output MOSFETS to the surrounding air, keeping the circuitry cool even under high power and output demand. General Features: Punch Series 4-Channel Class AB Car Amplifier RMS Power Rating: 4 ohms: 75 watts x 4 channel 2 ohms: 150 watts x 4 channel Bridged, 4 ohms: 300 watts x 2 channel MOSFET power supply Remote bass level input (remote level control sold separately) LED power, thermal, and protect indicators Tuned Bass EQ (0-18 dB bass boost at 45 Hz or 0-14 dB bass boost at 12 kHz depending on crossover selection) On-board differential inputs eliminate noise picked up by the signal cable 4/3/2 or Mono channel operation Integrated Trans ana technology simplifies the signal path of the amplifier allowing the signal to travel through the amplifier at a lower voltage. The result is greater reliability and exceptional sound quality RCA Pass-thru outputs MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowers the operating temperature and potential for noise - similar to circuit boards designed by aerospace manufacturers Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low Nickel-plated RCA level inputs Nickel-plated captive C-clamp terminals Variable high-pass filter (50-250 Hz, Butterworth, 12 dB/octave) Variable low-pass filter (50-250 Hz, Butterworth, 12 dB/octave) CEA-2006 compliant amplifier Frequency response: 20-20000 Hz Dimensions: 13-5/16"L x 7-3/4"W x 2-3/8"H What is in the box: 4-Channel amplifier Four 1-1/2" Self-tapping screws 2.5mm Allen wrench Quick setup instructions Certificate of Performance Rockford Fosgate Punch P600X4 owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.ca.gov

Rockford Fosgate 600W Punch Series 4-Channel Stereo Class AB Car Power Amplifier The Punch P600X4 is a 4-channel amplifier producing 150 Watts into all four channels at 2-Ohm. The P600X4 is perfect for a 4-way full-range system or a 3-way system having a front stage with subwoofers on the rear channels. The Punch P600X4 multi-channel amplifier is versatile to power any audio system configuration. The stealth top-mounted control panel not only provides a sleek finished look to the amp but also protects the vital controls. Our custom heat sink design uses high aluminum mass where it is needed most to maximize heat transfer from the output MOSFETS to the surrounding air, keeping the circuitry cool even under high power and output demand. General Features: Punch Series 4-Channel Class AB Car Amplifier RMS Power Rating: 4 ohms: 75 watts x 4 channel 2 ohms: 150 watts x 4 channel Bridged, 4 ohms: 300 watts x 2 channel MOSFET power supply Remote bass level input (remote level control sold separately) LED power, thermal, and protect indicators Tuned Bass EQ (0-18 dB bass boost at 45 Hz or 0-14 dB bass boost at 12 kHz depending on crossover selection) On-board differential inputs eliminate noise picked up by the signal cable 4/3/2 or Mono channel operation Integrated Trans ana technology simplifies the signal path of the amplifier allowing the signal to travel through the amplifier at a lower voltage. The result is greater reliability and exceptional sound quality RCA Pass-thru outputs MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowers the operating temperature and potential for noise - similar to circuit boards designed by aerospace manufacturers Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low Nickel-plated RCA level inputs Nickel-plated captive C-clamp terminals Variable high-pass filter (50-250 Hz, Butterworth, 12 dB/octave) Variable low-pass filter (50-250 Hz, Butterworth, 12 dB/octave) CEA-2006 compliant amplifier Frequency response: 20-20000 Hz Dimensions: 13-5/16"L x 7-3/4"W x 2-3/8"H What is in the box: 4-Channel amplifier Four 1-1/2" Self-tapping screws 2.5mm Allen wrench Quick setup instructions Certificate of Performance Rockford Fosgate Punch P600X4 owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate T750x1BD Power 500 Watts Watt Class-AD Mono Channel Amplifier + Absolute KIT4 4 Gauge Amplifier Installation Wiring Kit The Power T750X1bd is an ultra-compact, Class bd 750 Watt mono amplifier. It features a high-level auto turn-on, the CLEAN circuit with input/output clip detection, top-mounted controls, and dual fan forced induction cooling. Additionally, it has our patented Punch EQ circuit built in and Differential inputs with auto turn-on capabilities. Perfect for hybrid, electric, small cars, trucks, motorcycles, and side-by-side UTVs. General Features: Rockford Fosgate T750X1bd Class-BD 1-Ohm Stable Monoblock Amplifier RMS Power Rating: 4 ohms: 500 watts x 1 chan. 2 ohms: 750 watts x 1 chan. 1 ohm: 750 watts x 1 chan. Total power output: 750 watts CEA-2006 Compliant Amplifier Perfect for hybrid, electric, small cars, trucks, motorcycles, and side-by-side UTVs Optional remote Punch Level Control (PLC2 ready (w/ input clip indicator) LED power (blue), protect (red), input clip (red), and output clip (blue/red) indicators L.E.A.N. input/output clip detection and indicator LEDs Top-mounted controls Built-in Punch EQ circuit Real-time thermal sensing with Rollback technology Remote-Out feature when using high-level inputs Rockford Fosgate proprietary low impedance Constant Power Mono channel operation Speaker-level (high-level) inputs with auto turn-on 3-way protection circuitry (thermal, overload, and speaker short protection) Dual extruded heat sinks Dual fan cooled Input sensitivity: 150mV to 12V Speaker wire gauge: 10 AWG Frequency Response: 20 - 230Hz Total Harmonic Distortion (THD): <1.0% Variable low-pass filter: 50 - 250 Hz, 12 dB/octave Variable Bass Boost: 0 to +18 dB bass boost at 45 Hz Recommended Fuse: 100A (not included) 2-Year Warranty Absolute KIT 4 Gauge Amp Kit 17 ft. of red 4 AWG high current power cable 3 ft. of black 4 AWG ground cable 15 ft. of RCA triple shielded interconnect audio cable with built-in remote wire 20 ft. of 12 AWG OFC Speaker cable 20 ft. of 16 AWG remote turn-on wire 6 ft. of split loom tubing 1 Gold plated 80 AMP AGU fuse 1 4 AWG gold ring terminal 750W Power Series Ultra-Compact Class-BD Monoblock Amplifier 500 Watts RMS x 1 @ 4 ohms 750 Watts RMS x 1 @ 2 ohms 750 Watts RMS x 1 @ 1 ohm Complete 4 Gauge Amplifier Kit For Use in Any Car, Truck, RV, or Boat ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Rockford Fosgate Prime R2-500X1 500W Prime Series Monoblock Subwoofer Class D Amplifier Primed for performance, the R2-500X1 amplifier is a 500 watt, class-D, capable of operating at 4Ω or 2Ω mono. This amplifier is extremely efficient because of its class D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allows you to tune the bass for the desired level for the music. General Features: Rockford Fosgate Prime R2-500X1 RMS Power Rating: 4 ohms: 300 watts x 1 chan. 2 ohms: 500 watts x 1 chan. Total power output: 500 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeat able Auto Turn-On Circuit Features C.L.E.A.N. Set-up Variable Input Gain adjustment level R.L.C. Remote Level Control Variable Infrasonic Filter Continuously Variable On Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Full Range Class D Rollback Protection Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers Input sensitivity: Low-Level: 150 mV - 4 V High-Level: 450 mV - 12 V Frequency Response: 20 Hz - 250 Hz Total Harmonic Distortion (THD): >1% Crossover Controls Low-Pass: 50 Hz - 250 Hz Sub Infrasonic: 15 Hz - 40 Hz Recommended Fuse Rating: 80A 4 gauge power and ground wiring is recommended for installation Dimensions: "1.9" x "6.8" x "8.5" Authorized Internet Dealer 1 Year Manufacturer's Warranty What is in the box: Rockford Fosgate R2-500X1 owner's manual Mono subwoofer amplifier Wired Remote Level Control module 16' Remote cable (RJ-25 connector on both ends) One 7" Speaker input harnesses 3mm Allen Hex key Four 3/4" Screws Two 1/2" Screws 5 Flat washers 1 Nut Installation and Operation Instructions Certificate of Performance Rockford Fosgate contact information ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate M2-500X1 Marine 500-Watt Mono Amplifier Designed to withstand the elements, the M2-500X1 Element Ready amplifier is a 500-watt, class-D model, capable of operating at 4Ω or 2Ω mono. This amplifier is extremely efficient because of its class D technology which reduces demand on the electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allow you to tune the bass for the desired level for the music. General Features: mono marine subwoofer amplifier 300 watts RMS x 1 at 4 ohms 500 watts RMS x 1 at 2 ohms CTA-2006 compliant Class-D amplifier design wired remote included variable low-pass filter (50-250 Hz, 12 dB/octave) variable subsonic filter (15-40 Hz, 12 dB/octave) variable bass boost (0-18 dB at 45 Hz) marine features: Element Ready™ chassis and conformal-coated PC boards UV stable powder-coated cast aluminum heatsink zinc nickel-plated marine-grade brass connection terminals C.L.E.A.N. gain setup system includes clip lights auto remote turn-on preamp and speaker-level inputs preamp outputs wiring, fuse, and hardware not included with amplifier 4-gauge power and ground leads and an 80-amp fuse recommended dimensions: 8-1/2"W x 1-15/16"H x 6-13/16"D warranty: 2 years The M2-500X1 Element Ready Marine mono amplifier with 500 Watts RMS is packed with all the power and performance you have come to expect from Rockford Fosgate (Dimensions: 1.9" x 6.8" x 8.5") Class D technology makes this amp extremely efficient by reducing demand on the vehicles electrical system (RMS Power: 300 Watts x 1 @ 4Ω OR 500 Watts x 1 @ 2Ω) Built for the marine environment, this Element Ready amp features UV resistant protection, conformal coated circuit board, stainless steel mounting hardware, and marine-grade terminal connections to ensure long-lasting outdoor use Featuring C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass Famous Rockford Fosgate build quality with a full 2-year warranty when purchased from an authorized Rockford Fosgate reseller What is in the box: Mono marine amplifier Remote Punch Level Control module 16.5' Remote Punch Level Control cable (RJ-25 connector on both ends) 7" Speaker input harness 3mm Hex key Four 3/4" Screws Two 1/2" Screws 5 Flat washers 1 Nut Installation and Operation Instructions (English/ French/ Spanish/ German/ Italian) Certificate of Performance Verification Rockford Fosgate contacts information Rockford Fosgate M2-500X1 owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate PM100X1K Punch Marine 100 Watt Full-Range Mono Amplifier (Pair) The Punch Marine PM100X1 is a pair of 100-Watt full range dynamic power mono amplifiers that don’t need a power wire, is extremely compact in size, but big on power! The PM100X1 uses our patent-pending BTL technology that utilizes the speaker output of the radio to not only provide the audio signal it needs, but also the power that runs the unit. With no more load to the radio than a standard 2 or 4-ohm speaker, this design allows the amp to be connected to a 20-Watt output radio and produce up to 100 Watts dynamically! The small footprint of the PM100X1K amplifier allows it to be installed virtually anywhere along the speaker signal pathway from behind the radio to the door itself. This design makes the amplifier ideal for OEM or aftermarket as they can be hidden in the dash or doors of the vehicle. It is also IP67 water intrusion rated so it is also built to withstand the elements in motorcycle, boat, and motorsport applications. General Features: two compact mono amplifiers 60 watts RMS x 1 at 4 ohms (100 watts RMS x 1 at 2 ohms) CEA-2006 compliant patent-pending BTL "Freeload" technology requires no separate positive power lead connects to speaker wiring and chassis ground selectable high-pass filter (60, 80, or 100 Hz at 12 dB/octave) input impedance switch for low-impedance-capable receivers rubber switch cover IPX6 water intrusion rated dimensions: 3"W x 1-5/16"H x 3-15/16"D warranty: 2 years Patented BTL powered "Freeload" Technology Uses Stored Energy from BTL Amplifier to Produce Dynamic Power of Over 100 Watts High Level Turn On Pig Tail Connectivity for Easy Installation Sold in pairs (left/right) Harvests both B+ and Audio Signal from Standard Head Unit Speaker Outputs Optional B+ Connection for Non-Standard Speaker Outputs Short Circuit & Over Voltage Protection Extruded Aluminum Heat Sink and Thermal Protection Discrete surface mount technology Small Stealth Package that Allows for Anywhere Installation Selectable 4 and 2 Ohm Play Current Limited to Protect Head Unit for Both 4 Ohm and 2 Ohm Configurations Muted turn-on. The PM100X1K is a pair (left/right) of 100-Watt dynamic power mono amplifiers using DC and AC voltages present on existing radio speaker outputs This compact amplifier (1.3” x 3.0” x 3.9) is small but big on power (RMS Power Output: 60 x 1 @ 4-Ohm or 100 x 1 @ 2-Ohm) The versatile design can be used on a factory system using 2-Ohm or 4-Ohm factory or aftermarket speakers. The PM100X1K is also IPX6 rated so it can withstand the elements in mobile, motorsport, and marine applications High Level Turn on with selectable 60, 80, and 100 Hz Selectable 12dB/Oct HP Butterworth Crossover, featuring pigtail connectivity in a small stealth package allows for easy anywhere installation Famous Rockford Fosgate build quality ensures it will handle everything you throw at it! Full 2-year parts and labor warranty when purchased from an authorized Rockford Fosgate reseller What is in the box: The PM100X1K package contains two separately boxed PM100x1 mono amplifiers. Each amplifier box includes: Mono amplifier with attached 7.75" pigtail 12" Input/Output/Ground harness (16 AWG wires) 12" Power wire (16 AWG) 2 Self-tapping screws (3/4" length) Certificate of Performance Verification Rockford Fosgate PM100X1 owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca

 Rockford Fosgate Punch P500X1BD 500W RMS Punch Series Monoblock Class D Car Power Amplifier & 2 X P2D4-12 800W Max 12" Punch P2 Dual 4-Ohm Subwoofer The Punch P500X1bd is a mono amplifier capable of 500 Watts into a 1-Ohm load. The Class-BD technology produces bass more efficiently over traditional amps, and its frequency response allows it to be optimized for subwoofers. General Features: Punch BD Series Monoblock Class BD Car Amplifier RMS Power Rating: 4 ohms: 150 watts x 1 channel  RMS Power Rating: 2 ohms: 300 watts x 1 channel RMS Power Rating: 1 ohm: 500 watts x 1 channel CEA-2006 compliant amplifier MOSFET power supply Muted turn-on. Cast aluminum heatsink. 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protection indicators. Nickel-plated captive C-clamp terminals. Ultra-efficient Class BD circuitry to maximize amplifier power efficiency. On-board differential inputs eliminate noise picked up by the signal cable. Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately) MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span. Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances. Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low. DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowering the operating temperature and potential for noise-like circuit boards designed by aerospace manufacturers. Input sensitivity: 150mV - 12V On-board Punch EQ with +18dB boost @ 45Hz. Variable low-pass filter: 50-250 Hz Selectable infrasonic filter: off / 28 Hz Frequency response: 20 - 250 Hz Total Harmonic Distortion: <1.0% Dimensions: 11"L x 7-3/4"W x 2-3/8"H 8 AWG to 18 AWG speaker wire output terminals Authorized Internet Dealer 1-year Manufacturer's Warranty 2 Rockford Fosgate P2D4-12 12" 1600W Car Audio Subwoofer Rockford Fosgate has always been known as "The PUNCH," and the P2 12" subwoofer continues with the tradition. Kevlar fiber-reinforced paper cones deliver bass impact you can feel along with VAST technology to increase surface cone area up to 25%. The P2 subwoofers perform best in standard sealed and vented enclosures. Includes diamond cut cast aluminum trim ring. Optional grille insert available. General Features: 12" Dual 4 ohm Punch Stage 2 Subwoofer Power Handling: RMS: 400 watts Power Handling: Peak: 800 watts Recommended power range: 300 - 500 watts RMS Klippel Verified Flex-fit Mounting pattern Proprietary spider venting/cooling technique StampCast basket with integrated spider venting Sturdy 16 gauge compound bend frame geometry High modulus Kevlar re-inforced paper-pulp cone Semi-flexible, PVC removable protective motor cover Multi-point high-temp/high-strength neck joint bonding technique Tall-profile VAST; Santoprene surround for larger surface area Dual tear & fatigue resistant poly-cotton spider with woven tinsel leads Fatigue-resistant and reduced strain "stitched on" flexible lead wire design Proprietary all metal, radially oriented compression input terminal assembly Optimized motor magnetics with extended pole and bumped vented backplate High temp 2.25" voice coil w/ spun-laced Nomex insulating reinforcement collar Die-Cast aluminum soft-touch painted trim ring allows for optional integrated grill Mounting Depth: 6.40" Cutout Diameter: 11.22" Magnet Weight: 72.80 oz Frequency Response: 27.2 - 250 Hz Xmax: 13.3mm Sensitivity: 86 dB @ 1 watt / 1 meter Weight: 16 Ibs 1-year Manufacturer's Warranty Authorized Internet Dealer What is in the P2D4-12 package: P2D4-12 owner's manual Two 12" Dual 4-ohm voice coil subwoofer Trim ring Eight 1-1/8" Allen head screws 4mm Allen head bit Installation/Operation manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Punch P500X1BD 500W RMS Punch Series Monoblock Class D Car Power Amplifier + Absolute KIT4 Amp Kit The Punch P500X1bd is a mono amplifier capable of 500 Watts into a 1-Ohm load. The Class-BD technology produces bass more efficiently over traditional amps, and its frequency response allows it to be optimized for subwoofers. General Features: Punch BD Series Monoblock Class BD Car Amplifier RMS Power Rating: 4 ohms: 150 watts x 1 chan. 2 ohms: 300 watts x 1 chan. 1 ohm: 500 watts x 1 chan. CEA-2006 compliant amplifier MOSFET power supply Muted turn-on. Cast aluminum heatsink. 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protect indicators. Nickel-plated captive C-clamp terminals. Ultra-efficient Class BD circuitry to maximize amplifier power efficiency. On-board differential inputs eliminate noise picked up by the signal cable. Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately) MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span. Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances. Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low. DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowers the operating temperature and potential for noise-like circuit boards designed by aerospace manufacturers. Input sensitivity: 150mV - 12V On-board Punch EQ with +18dB boost @ 45Hz. Variable low-pass filter: 50-250 Hz Selectable infrasonic filter: off / 28 Hz Frequency response: 20 - 250 Hz Total Harmonic Distortion: <1.0% Dimensions: 11"L x 7-3/4"W x 2-3/8"H 8 AWG to 18 AWG speaker wire output terminals Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the P500X1bd box: Mono subwoofer amplifier Four 1-1/2" Self-tapping screws 2.5mm Allen wrench Quick setup instructions Certificate of Performance P500X1bd owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Punch P500X1BD 500W RMS Punch Series Monoblock Class D Car Power Amplifier The Punch P500X1bd is a mono amplifier capable of 500 Watts into a 1-Ohm load. The Class-BD technology produces bass more efficiently over traditional amps, and its frequency response allows it to be optimized for subwoofers. General Features Punch BD Series Monoblock Class BD Car Amplifier RMS Power Rating: 4 ohms: 150 watts x 1 chan. 2 ohms: 300 watts x 1 chan. 1 ohm: 500 watts x 1 chan. CEA-2006 compliant amplifier MOSFET power supply Muted turn-on. Cast aluminum heatsink. 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protect indicators. Nickel-plated captive C-clamp terminals. Ultra-efficient Class BD circuitry to maximize amplifier power efficiency. On-board differential inputs eliminate noise picked up by the signal cable. Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately) MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span. Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances. Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low. DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowering the operating temperature and potential for noise-like circuit boards designed by aerospace manufacturers. Input sensitivity: 150mV - 12V On-board Punch EQ with +18dB boost @ 45Hz. Variable low-pass filter: 50-250 Hz Selectable infrasonic filter: off / 28 Hz Frequency response: 20 - 250 Hz Total Harmonic Distortion: <1.0% Dimensions: 11"L x 7-3/4"W x 2-3/8"H 8 AWG to 18 AWG speaker wire output terminals Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the P500X1bd box: Mono subwoofer amplifier Four 1-1/2" Self-tapping screws 2.5mm Allen wrench Quick setup instructions Certificate of Performance P500X1bd owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Punch P500X1BD 500W RMS Punch Series Monoblock Class D Car Power Amplifier The Punch P500X1bd is a mono amplifier capable of 500 Watts into a 1-Ohm load. The Class-BD technology produces bass more efficiently over traditional amps, and its frequency response allows it to be optimized for subwoofers. General Features Punch BD Series Monoblock Class BD Car Amplifier RMS Power Rating: 4 ohms: 150 watts x 1 chan. 2 ohms: 300 watts x 1 chan. 1 ohm: 500 watts x 1 chan. CEA-2006 compliant amplifier MOSFET power supply Muted turn-on. Cast aluminum heatsink. 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protect indicators. Nickel-plated captive C-clamp terminals. Ultra-efficient Class BD circuitry to maximize amplifier power efficiency. On-board differential inputs eliminate noise picked up by the signal cable. MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span. Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances. Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low. DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowers the operating temperature and potential for noise-like circuit boards designed by aerospace manufacturers. Input sensitivity: 150mV - 12V On-board Punch EQ with +18dB boost @ 45Hz. Variable low-pass filter: 50-250 Hz Selectable infrasonic filter: off / 28 Hz Frequency response: 20 - 250 Hz Total Harmonic Distortion: <1.0% Dimensions: 11"L x 7-3/4"W x 2-3/8"H 8 AWG to 18 AWG speaker wire output terminals Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the P500X1bd : Mono subwoofer amplifier Four 1-1/2" Self-tapping screws 2.5mm Allen wrench Quick setup instructions Certificate of Performance P500X1bd owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate T750X1bd 750W Power Series Ultra-Compact Class-BD Monoblock Amplifier The Power T750X1bd 750 Watt mono, the ultra-compact amplifier is built on Rockford Fosgate’s patented Class bd technology platform. This design creates a highly efficient design that reduces the electrical impact on the vehicle charging system by using the efficient Class D technology while maintaining fidelity combining it with Class b topology. Flexible vehicle integration is achieved via a configurable input harness with Molex style connectivity that accepts both RCA and speaker level signals while our differential input circuitry eliminates signal noise from entering the amplifier resulting in a clean audio signal. When using speaker-level input signals, the amplifier also has integrated auto turn-on capabilities and converts its remote input terminal to an output that can be used to turn on additional amplifiers. This can eliminate the need of sourcing a separate remote turn-on signal for the amplifier from the vehicle. Top-mounted controls allow easy access to the built-in low pass crossover, patented Punch EQ boost circuit and our patented C.L.E.A.N. input/output clip detection circuits. The 3-stage thermal lock extrusion with dual fan forced induction keeps everything cool while our real-time thermal/protection schemes safeguard the amplifier in the event of overheating or short circuit conditions. The unit is also compatible with our Punch PLC2 remote level controller and is ideal for those installations where you need a compact amplifier that can produce high output power. General Features: Rockford Fosgate T750X1bd Class-BD 1-Ohm Stable Monoblock Amplifier RMS Power Rating: 4 ohms: 500 watts x 1 chan. 2 ohms: 750 watts x 1 chan. 1 ohm: 750 watts x 1 chan. Total power output: 750 watts CEA-2006 Compliant Amplifier Perfect for hybrid, electric, small cars, trucks, motorcycles, and side-by-side UTVs Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) LED power (blue), protect (red), input clip (red), and output clip (blue/red) indicators C.L.E.A.N. input/output clip detection and indicator LEDs Top-mounted controls Built-in Punch EQ circuit Real-time thermal sensing with Rollback technology Remote-Out feature when using high-level inputs Rockford Fosgate proprietary low impedance Constant Power Mono channel operation Speaker-level (high-level) inputs with auto turn-on 3-way protection circuitry (thermal, overload, and speaker short protection) Dual extruded heat sinks Dual fan cooled Input sensitivity: 150mV to 12V Speaker wire gauge: 10 AWG Frequency Response: 20 - 230Hz Total Harmonic Distortion (THD): <1.0% Variable low-pass filter: 50 - 250 Hz, 12 dB/octave Variable Bass Boost: 0 to +18 dB bass boost at 45 Hz Recommended Fuse: 100A (not included) Dimensions: 4.3"W x 8.3"L x 1.6"H Authorized Internet Dealer 1-year Manufacturer's Warranty ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov