Rockford Fosgate 5 Channel or more Amplifiers (7)

Rockford Fosgate Prime R2-750X5 750W Prime Series 5-Channel Full Range Class D Amplifier Primed for performance, the R2-750X5 is a 750 watt rated, full-range class-D amplifier capable of operating at 4Ω or 2Ω stereo with a mono subwoofer channel that can be run at 4Ω or 2Ω. The front/rear stereo channels can also be run at a 4Ω bridged/mono load. This amplifier is extremely efficient because of its Class-D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. supply that generates more dynamic power as voltage increases, and an integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. Rockford Fosgate's R2 amplifiers are the building blocks for great audio systems, powerful enough to even DRIVE our Punch speakers and subwoofers. They have undergone an amazing upgrade by packing them with the latest features at an incredible value. Best of all, they are designed and engineered here in Tempe, Arizona. General Features: Rockford Fosgate Prime R2-750X2 Class-D Full-Range 5-Channel Amplifier RMS Power Rating: 4 ohms: 50 watts x 4 Channel RMS Power Rating: 2 ohms: 100 watts x 4 Channel Bridged RMS Power Rating 4 ohms: 200 watts x 2 Channel Sub Channel: 4 ohms: 200 x 1 Channel Sub Channel: 2 ohms: 350 x 1 Channel Total power output: 600 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeat able Auto Turn on Circuit Features C.L.E.A.N. Set-up 2/4/5 Channel Input Selection Switch L.C. Remote Level Control Variable Infrasonic Filter Front, Rear, and Sub Variable Input Gain adjustment level Continuously Variable on-Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Full Range Class D Rollback Protection Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers Frequency Response: 20 Hz - 20 kHz Total Harmonic Distortion (THD): >1% Crossover Controls: Variable high-pass filter: 50 - 250 Hz, 24 dB/octave Crossover Controls: Variable low-pass filter: 50 - 250 Hz, 24 dB/octave Sub Low-Pass: 50 Hz - 250 Hz Sub Infrasonic: 15 Hz - 40 Hz Fuse Rating: 120A 4-gauge power and ground wiring are recommended for installation. Dimensions: 1.9"x6.8"x11.2" Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the box: 5-Channel amplifier Wired Remote Level Control module 16' Remote cable (RJ-25 connector on both ends) Three 7" Speaker input harnesses 3mm Allen Hex key Four 3/4" Screws Two 1/2" Screws 5 Flat washers 1 Nut Installation and Operation Instructions (English/ French/ Spanish/ German/ Italian) Certificate of Performance Rockford Fosgate contacts information Rockford Fosgate R2-750X5 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Rockford Fosgate Punch P1000X5 5-channel car amplifier — 75 watts RMS x 4 at 4 ohms + 500 watts RMS x 1 at 1 ohm The Punch P1000X5 is an ultra-efficient 5-channel amplifier capable of running your entire system without excessive drain on your charging system. The P1000X5 is perfect for running a front/rear system and a dedicated subwoofer. The P1000X5 1,000 Watt full-range 5-channel is the one-and-only amplifier you will need to run your entire system. Run dash speakers off the front channels, run back speakers off the rear channels, and run subwoofer(s) off the 5th channel! Known worldwide for brute power, this amplifier offers a higher level of efficiency along with tri-stage protection that covers thermal, over-current, and short circuits. General Features: 5-channel car amplifier 75 watts RMS x 4 + 150 watts RMS x 1 at 4 ohms 125 watts RMS x 4 + 300 watts RMS x 1 at 2 ohms 250 watts RMS x 2 bridged at 4 ohms + 500 watts RMS at 1 ohm CEA-2006 compliant variable high- and low-pass filters (50-250 Hz, 12 dB/octave) variable PEQ2 bass/treble boost (0-18 dB at 45 Hz and 0-14 dB at 12.5K Hz) switchable subsonic filter (28 Hz, 12 dB/octave) on subwoofer channel L.E.A.N. gain setup system includes test tone CD test tones are also available as MP3 download from Amazon on Demand, Rhapsody, Google Play, and Spotify, labeled "3sixty.3 setup disc" (Punch amps and the 3sixty.3 use the same test tone tracks for setup) Class-BD amplifier design frequency response: 20-20K Hz Dynamic Thermal Management and MEHSA MOSFET cooling systems MOSFET power and output stages preamp and speaker-level inputs (speaker-level inputs require a speaker wire to RCA adapter) signal-sensing turn-on with speaker-level inputs eliminate the need for remote turn-on lead optional PLC2 wired remote level control with clip light available 4-gauge power and ground leads and a 150-amp fuse recommended — wiring and hardware not included with amplifier no onboard fuses — when installing multiple amps in a system, an additional 150-amp in-line fuse between the distribution block and the amplifier is recommended. 15-1/8"W x 2-7/16"H x 8-13/16"D What is in the box: 5-Channel amplifier Four 1-1/2" Self-tapping screws 5mm Allen wrench Quick setup instructions Certificate of Performance Setup/Manual disc Rockford Fosgate Punch P1000X5 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Rockford Fosgate Punch P1000X5 5-channel car amplifier — 75 watts RMS x 4 at 4 ohms + 500 watts RMS x 1 at 1 ohm The Punch P1000X5 is an ultra-efficient 5-channel amplifier capable of running your entire system without excessive drain on your charging system. The P1000X5 is perfect for running a front/rear system and a dedicated subwoofer. The P1000X5 1,000 Watt full-range 5-channel is the one-and-only amplifier you will need to run your entire system. Run dash speakers off the front channels, run back speakers off the rear channels, and run subwoofer(s) off the 5th channel! Known worldwide for brute power, this amplifier offers a higher level of efficiency along with tri-stage protection that covers thermal, over-current, and short circuits. General Features: 5-channel car amplifier 75 watts RMS x 4 + 150 watts RMS x 1 at 4 ohms 125 watts RMS x 4 + 300 watts RMS x 1 at 2 ohms 250 watts RMS x 2 bridged at 4 ohms + 500 watts RMS at 1 ohm CEA-2006 compliant variable high- and low-pass filters (50-250 Hz, 12 dB/octave) variable PEQ2 bass/treble boost (0-18 dB at 45 Hz and 0-14 dB at 12.5K Hz) switchable subsonic filter (28 Hz, 12 dB/octave) on subwoofer channel L.E.A.N. gain setup system includes test tone CD test tones are also available as MP3 download from Amazon on Demand, Rhapsody, Google Play, and Spotify, labeled "3sixty.3 setup disc" (Punch amps and the 3sixty.3 use the same test tone tracks for setup) Class-BD amplifier design frequency response: 20-20K Hz Dynamic Thermal Management and MEHSA MOSFET cooling systems MOSFET power and output stages preamp and speaker-level inputs (speaker-level inputs require a speaker wire to RCA adapter) signal-sensing turn-on with speaker-level inputs eliminate the need for remote turn-on lead optional PLC2 wired remote level control with clip light available 4-gauge power and ground leads and a 150-amp fuse recommended — wiring and hardware not included with amplifier no onboard fuses — when installing multiple amps in a system, an additional 150-amp in-line fuse between the distribution block and the amplifier is recommended. 15-1/8"W x 2-7/16"H x 8-13/16"D What is in the box: 5-Channel amplifier Four 1-1/2" Self-tapping screws 5mm Allen wrench Quick setup instructions Certificate of Performance Setup/Manual disc Rockford Fosgate Punch P1000X5 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Rockford Fosgate Punch P1000X5 5-channel car amplifier — 75 watts RMS x 4 at 4 ohms + 500 watts RMS x 1 at 1 ohm The Punch P1000X5 is an ultra-efficient 5-channel amplifier capable of running your entire system without excessive drain on your charging system. The P1000X5 is perfect for running a front/rear system and a dedicated subwoofer. The P1000X5 1,000 Watt full-range 5-channel is the one-and-only amplifier you will need to run your entire system. Run dash speakers off the front channels, run back speakers off the rear channels, and run subwoofer(s) off the 5th channel! Known worldwide for brute power, this amplifier offers a higher level of efficiency along with tri-stage protection that covers thermal, over-current, and short circuits. General Features: 5-channel car amplifier 75 watts RMS x 4 + 150 watts RMS x 1 at 4 ohms 125 watts RMS x 4 + 300 watts RMS x 1 at 2 ohms 250 watts RMS x 2 bridged at 4 ohms + 500 watts RMS at 1 ohm CEA-2006 compliant variable high- and low-pass filters (50-250 Hz, 12 dB/octave) variable PEQ2 bass/treble boost (0-18 dB at 45 Hz and 0-14 dB at 12.5K Hz) switchable subsonic filter (28 Hz, 12 dB/octave) on subwoofer channel L.E.A.N. gain setup system includes test tone CD test tones are also available as MP3 download from Amazon on Demand, Rhapsody, Google Play, and Spotify, labeled "3sixty.3 setup disc" (Punch amps and the 3sixty.3 use the same test tone tracks for setup) Class-BD amplifier design frequency response: 20-20K Hz Dynamic Thermal Management and MEHSA MOSFET cooling systems MOSFET power and output stages preamp and speaker-level inputs (speaker-level inputs require a speaker wire to RCA adapter) signal-sensing turn-on with speaker-level inputs eliminate the need for remote turn-on lead optional PLC2 wired remote level control with clip light available 4-gauge power and ground leads and a 150-amp fuse recommended — wiring and hardware not included with amplifier no onboard fuses — when installing multiple amps in a system, an additional 150-amp in-line fuse between the distribution block and the amplifier is recommended. 15-1/8"W x 2-7/16"H x 8-13/16"D What is in the box: 5-Channel amplifier Four 1-1/2" Self-tapping screws 5mm Allen wrench Quick setup instructions Certificate of Performance Setup/Manual disc Rockford Fosgate Punch P1000X5 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Rockford Fosgate Power T1000x5ad Compact 5-channel car amplifier 100 watts RMS x 4 at 2 to 4 ohms + 600 watts RMS x 1 at 1 to 2 ohms Super-compact, bursting with powerRockford Fosgate's Power Series T1000X5ad 5-channel amplifier can send 100 watts RMS each to four separate speakers while delivering up to 600 watts RMS to a subwoofer. Or you could use this tiny powerpack to run a couple of high-performance components with 200 watts each along with 600 watts RMS for the sub. A dual-fan forced air cooling system keeps this sturdy little amp from overheating, so it can play hard for a long time. Class AD: accurate and powerfulRockford Fosgate uses their proprietary Class AD amplifier technology, combining the high fidelity of a Class A system with the high efficiency of their special Class D technology, to bring you this ultra-efficient, high-output amplifier. In other words, this compact amp produces more power with less current draw from your vehicle's charging system than most other amps on the road today.Rockford Fosgate's high-tech solutions yield more powerThis Power Series amplifier actively monitors speaker and subwoofer performance, using Rockford Fosgate's Constant Power technology. A speaker's impedance naturally fluctuates as it performs, fighting against your amp's output. So, just like your cruise control increases the engine's RPM to maintain your car's speed uphill, Constant Power maintains this amp's output by increasing its internal voltage and current flow when the speaker's impedance rises. This results in up to a 25% increase in the amp's total power output. Easy to set for optimum performanceRockford Fosgate's C.L.E.A.N. technology (Calibrated Level Eliminates Audible Noise) setup system ensures your music will sound as clean and powerful as possible. It works like this: first download the setup tones from Rockford Fosgate, then play the tone, adjust the receiver volume until a red clip light on the amp goes out, then turn the amp gain up until a blue light comes on. It's that simple — your amplifier will be perfectly set to match your receiver's output. When your receiver reaches maximum clean volume, you'll get maximum clean power from your Power amp. At quiet listening levels, you'll hear less background noise and more of your music. Clip lights monitor distortionIf that blue light turns solid red while you're playing music, the amp's telling you that your source is distorting and you should turn it down, or risk damage to your gear. The optional PLC2 remote level control also doubles as a clip indicator, so you can see from the front seat if your music's clipping and restore pristine sound. Product highlights: 5-channel car amplifier 100 watts RMS x 4 + 400 watts RMS x 1 at 4 ohms 100 watts RMS x 4 + 600 watts RMS x 1 at 2 ohms 200 watts RMS x 2 bridged at 4 ohms + 600 watts RMS at 1 ohm CEA-2006 compliant Features: Class-AD amp technology on front and rear channels; Class BD on sub channel with Constant Power topology C.L.E.A.N. gain setup system includes clip lights and link to Rockford Fosgate's setup tones differential input circuitry helps eliminate hum dual-fan forced induction cooling variable high- and low-pass filters (50-250 Hz, 12 dB/octave) on front and rear channels variable low-pass filter (50-250 Hz, 12 dB/octave) on subwoofer channel switchable subsonic filter (28 Hz, 12 dB/octave) on subwoofer channel variable Punch EQ bass/treble boost (0-18 dB at 45 Hz and 0-14 dB at 12.5K Hz) on all channels optional PLC2 wired remote level control with clip light available More Info: preamp and speaker-level inputs signal-sensing turn-on with speaker-level inputs eliminate need for remote turn-on lead 8-gauge power and ground leads and a 100-amp fuse recommended — wiring and hardware not included with amplifier no onboard fuses — when installing multiple amps in a system, an additional 100-amp in-line fuse between the distribution block and the amplifier is recommended 12-1/2"W x 1-11/16"H x 4-5/16"D warranty: 2 years (extends to 3 years when purchased with an appropriate Rockford Fosgate amp wiring kit ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca

Rockford Fosgate Punch P1000X5 5-channel car amplifier 75 watts RMS x 4 at 4 ohms + 500 watts RMS x 1 at 1 ohm Big power for your whole systemRockford Fosgate's Punch P1000X5 amplifier can power your entire system, delivering 75 watts RMS to each of your front and rear speakers, along with up to 500 watts RMS to a subwoofer. The sub channel's low-pass and subsonic filters come in handy for getting the right sound from your sub/enclosure combo, and you can use the amp's high-pass filters to remove the bass from your full-range speakers so they'll play more efficiently. The Punch EQ2 includes bass and treble boosts, in case you want to liven up the mix. Not worried about rear speakers? You can also switch this amp into 3-channel mode to drive a couple of high-performance components with 250 watts RMS each while still powering a sub with up to 500 watts. Easy to set for optimum performanceOnce again, Rockford Fosgate steps away from the crowd with their C.L.E.A.N. technology (Calibrated Level Eliminates Audible Noise) — a setup system that ensures your music will sound as clean and powerful as possible. It works like this: first download the setup tones from Rockford Fosgate, then play the tone, adjust the receiver volume until a red clip light on the amp goes out, then turn the amp gain up until a blue light comes on. It's that simple — your amplifier will be perfectly set to match your receiver's output. When your receiver reaches maximum clean volume, you'll get maximum clean power from your Power amp. At quiet listening levels, you'll hear less background noise and more of your music. Keeps an eye on things while playingIf that blue light turns solid red while you're playing music, the amp's telling you that your source is distorting and you should turn it down, or risk damage to your gear. The optional PLC2 remote level control also doubles as a clip indicator, so you can see from the front seat if your music's clipping. The amp's built-in computer keeps tabs on the output current, ensuring that plunging speaker impedances (they change during play) or even a short circuit won't hurt anything. Eliminating heat raises efficiency and lowers distortionRockford Fosgate's Dynamic Thermal Management system uses forced air to dissipate heat evenly across the amp and out through the high-mass heatsink, efficiently drawing heat away from vital internal parts. Their proprietary MEHSA cooling process maximizes the heat transfer from the MOSFET devices to the heatsink, allowing the heat to escape more readily, so the transistors stay cooler and work better. Product highlights: 5-channel car amplifier 75 watts RMS x 4 + 150 watts RMS x 1 at 4 ohms 125 watts RMS x 4 + 300 watts RMS x 1 at 2 ohms 250 watts RMS x 2 bridged at 4 ohms + 500 watts RMS at 1 ohm CEA-2006 compliant Features: variable high- and low-pass filters (50-250 Hz, 12 dB/octave) variable PEQ2 bass/treble boost (0-18 dB at 45 Hz and 0-14 dB at 12.5K Hz) switchable subsonic filter (28 Hz, 12 dB/octave) on subwoofer channel C.L.E.A.N. gain setup system includes clip lights and link to Rockford Fosgate's setup tones Class-BD amplifier design frequency response: 20-20K Hz Dynamic Thermal Management and MEHSA MOSFET cooling systems MOSFET power and output stages preamp and speaker-level inputs (speaker-level inputs require a speaker wire to RCA adapter) signal-sensing turn-on with speaker-level inputs eliminate need for remote turn-on lead More Info: optional PLC2 wired remote level control with clip light available 4-gauge power and ground leads and an 150-amp fuse recommended — wiring and hardware not included with amplifier no onboard fuses — when installing multiple amps in a system, an additional 150-amp in-line fuse between the distribution block and the amplifier is recommended 15-1/8"W x 2-7/16"H x 8-13/16"D warranty: 1 year ⚠️Warning: Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Rockford Fosgate Punch P300X1 Mono amplifier 300 watts RMS x 1 at 2 ohms Big power for your sub or speaker systemRockford Fosgate's Punch P300X1 mono amplifier produces up to 300 watts RMS, giving you plenty of clean power for your rhythm track. With frequency response from 20 to 20,000 Hz, this full-range amp can also power a center channel or component speaker. You can use the low-pass filter to tune the sizzle away from your sub, or the high-pass filter to keep the lows out of a component speaker. The Punch EQ2 gives you a variable bass and treble boost, in case you want to add a little of that boom and sizzle back into the mix. Easy to set for optimum performanceOnce again, Rockford Fosgate steps away from the crowd with their C.L.E.A.N. technology (Calibrated Level Eliminates Audible Noise) — a setup system that ensures your music will sound as clean and powerful as possible. It works like this: first download the setup tones from Rockford Fosgate, then play the tone, adjust the receiver volume until a red clip light on the amp goes out, then turn the amp gain up until a blue light comes on. It's that simple — your amplifier will be perfectly set to match your receiver's output. When your receiver reaches maximum clean volume, you'll get maximum clean power from your Power amp. At quiet listening levels, you'll hear less background noise and more of your music. Keeps an eye on things while playingIf that blue light turns solid red while you're playing music, the amp's telling you that your source is distorting and you should turn it down, or risk damage to your gear. The optional PLC2 remote level control also doubles as a clip indicator, so you can see from the front seat if your music's clipping. The amp's built-in computer keeps tabs on the output current, ensuring that plunging speaker impedances (they change during play) or even a short circuit won't hurt anything. Maintaining coolness raises efficiency and lowers distortionRockford Fosgate's Dynamic Thermal Management system uses forced air to dissipate heat evenly across the amp and out through the high-mass heatsink, efficiently drawing heat away from vital internal parts. Their proprietary MEHSA cooling process maximizes the heat transfer from the MOSFET devices to the heatsink, allowing the heat to escape more readily, so the transistors stay cooler and work better. Product highlights: full-range mono amplifier frequency response: 20-20,000 Hz 200 watts RMS x 1 at 4 ohms (300 watts RMS x 1 at 2 ohms) CEA-2006 compliant Features: variable high- and low-pass filter filter (50-250 Hz, 12 dB/octave) variable PEQ2 bass/treble boost (0-18 dB at 45 Hz and 0-14 dB at 12.5K Hz) C.L.E.A.N. gain setup system includes clip lights and link to Rockford Fosgate's setup tones Class-AB amplifier design Dynamic Thermal Management and MEHSA MOSFET cooling systems MOSFET power and output stages preamp inputs and outputs speaker-level inputs (speaker wire to RCA adapter required) signal-sensing turn-on with speaker-level inputs eliminate need for remote turn-on lead More Info: optional PLC2 wired remote level control with clip light available 8-gauge power and ground leads and an 50-amp fuse recommended — wiring and hardware not included with amplifier no onboard fuses — when installing multiple amps in a system, an additional 50-amp in-line fuse between the distribution block and the amplifier is recommended 9-15/16"W x 2-7/16"H x 7-13/16"D warranty: 1 year ⚠️Warning: Cancer and Reproductive Harm-www.P65Warnings.ca.gov