Guitar Amplifiers (86)

Traynor DHX12 DarkHorse Series 1 x 12-inch Guitar Extension Cabinet - 25 Watts The DHX12 features a 16-Ohm Celestion G12M Greenback and an innovative tone gate that permits conversion from closed-back solid bottom end to classic open-back combo performance. Even if you dont have a DarkHorse, the DHX12 is likely to make your combo sound better used as an extension cab, and weighing in at a less than 35 pounds, its even easy to carry around. General Features: Designed as the ideal tone partner for the Dark Horse Head Solid plywood cabinet construction Single 12-inch Celestion™ G12M Greenback speaker Operates at 16-ohms Innovative conversion between open and closed back operation Made in Canada Specifications: Cabinet Program Power (Watts) 25 Cabinet Impedance (Ohms) 16 Speaker Configuration – LF 12-inch Celestion Greenback G12M Frequency Response (Hz +/-3dB) 75 – 5000 Hz Inputs 1 Other Features Sensitivity: 98dB @1Watt/1m Dimensions (DWH, inches) 10 x 20 x 18 Dimensions (DWH, cm) 24.4 x 50.8 x 45.7 Weight (lbs / kg) 33.5 / 15.2 **Specifications subject to change without notice Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Traynor DH15H 15 Watt All-tube Guitar Head The DarkHorse 15H all-tube guitar head is destined to be an instant classic. Fifteen watts of all-tube tone in a sub-compact head and cabinet combination specifically designed with the travelling musician in mind. Simple Gain, Bass, Treble and Master controls allow easy access to the perfect amp sound on stage or in the studio. A Tonestack switch allows for either Brit or USA voicings or the Pure mode which bypasses the tone stack entirely, delivering a mid and overall gain boost allowing for the most direct signal path possible between your fingers and the speaker. Selectable output power switches between two separate output stages a higher headroom 15-watt pentode stage or a 2-watt triode stage for increased drive. A combination of 8 and 16-ohm outputs allows the DarkHorse to drive virtually any cabinet configuration. General Features: Delivers Full 15 Watts in higher power (6V6) Mode Selectable Low Power 2-watt (12AU7) Mode Simple Gain, Bass, Treble & Master Volume control set Brit / USA / Pure switch for the tone stack (delivering a Mid Boost and Overall Gain Boost when in Pure mode) Uses hand selected 12AX7 (x2), 6V6 (x2), and 12AU7 (x1) tubes Versatile speaker outputs allow the DH15H to drive 1 x 16-ohm, 1 x 8-ohm or 2 x 16-ohm cabinet configurations Gig bag is included Optional DHX12 (1 x 12-inch) and DHX212 (2 x 12-inch) Extension Cabinets available Made in Canada Specifications: Power @ min. impedance (Watts) 6V6 mode: 12 watts12AU7 mode: 0.8 watts Burst Power 6V6 mode: 15 watts12AU7 mode: 2 watts Preamp Tubes 2 x 12AX7 Power Tubes 2 x 6V6 / 1 x UA7 Inputs 1 Channel 1 – Inputs 1/4-inch phono Channel 1 – Controls Gain, Bass, Treble, Master Channel 1 – Switches Brit / Pure / USA Speaker Outputs Selectable: 1 x 16-ohm / 1 x 8-ohm / 2 x 16-ohm Dimensions (DWH, inches) 6 x 12.75 x 6 Dimensions (DWH, cm) 15.25 x 32.5 x 15.25 Weight (lbs / kg) 11 / 5 **Specifications subject to change without notice Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Traynor YGL2 30-watt All-Tube Guitar Combo Traynor recreates the classic cathode bias amp tone in the 30-watt YGL2 all-tube two-channel combo. Classic ToneTraynor YGL2 uses a 12-inch Celestion Vintage 30 speaker and hand-selected EL84 tubes configured in a proven Class-A amplifier design to deliver a truly classic amp tone. Ideal for stage or studio, the YGL2 is built to meet the need of the discerning guitarist in search of a classic, yet versatile guitar amp. Maximum VersatilityThe Traynor YGL2 offers clean and overdrive channels with separate level controls, master volume and a simple bass / mid / treble tone stack. A Mode switch relocates the tone stack relative to the gain stage, giving the YGL2 either a crisp American style tube amp tone for clarity and definition (USA mode) or a grittier, more spongy British flavor associated with the great UK amps of the 60s and 70s ( Brit mode). Additional Tone ShapingThe Vintage / Modern switch on the Traynor YGL2 offers additional tone shaping that offers the player a choice between a truly classic vintage tube drive or a more aggressive scooped guitar tone for the guitarist seeking a more modern guitar sound. Unmatched ReliabilityThe Traynor YGL2 combo is made in Canada using solid plywood cabinet construction, heavy gauge steel chassis, high quality pots and jacks. General Features: 30-watt All-Tube Guitar Combo 12-inch Celestion Vintage 30 Speaker Class-A Cathode Bias Amplifier Design Uses 3 x 12AX7 and 4 x EL84 Tubes Clean Volume, Overdrive Gain, Overdrive Volume and Master Volume Controls Shared Bass, Middle, Treble and Reverb controls Master USA/Brit and Vintage/Modern Mode Switches Series Effects Loop Footswitch for Channel Select and Reverb Defeat External Speaker Jack Made in Canada Specifications: Cabinet Impedance (Ohms) 8 Power @ min. impedance (Watts) 30 Speaker Configuration - LF 12-inch Preamp Tube 3 x 12AX7 Power Amp Tube 4 x EL84 Inputs 2, footswitchable Channel 1 – Inputs 1/4-inch Channel 1 – Controls Clean Volume Channel 1 – Switches USA/Brit, Bright Channel 2 – Controls Overdrive Gain, Overdrive Volume Main Tone Controls Bass, Mid, Treble Line Out (type / configuration) 1/4 inch TRS / Rear Effects Loop / Location Yes / Rear Effects Footswitch / Function Yes / Channel Select / Reverb Internal Reverb / Effects Accutronics Spring Reverb LED Indicators Power/Standby, Ch.1, Ch.2 Dimensions (DWH, inches) 10 x 22.5 x 20 Dimensions (DWH, cm) 25 x 57 x 51 Weight (lbs / kg) 45 / 20 **Specifications subject to change without notice Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Hughes & Kettner HKFS2RD TubeMeister 2-channel Footswitch The Hughes & Kettner TubeMeister 2-channel footswitch unlocks the full potential of your guitar amplifier. This rugged footswitch boasts vivid per-channel LED indicators for at-a-glance confirmation of what’s going on. The guitarists here at Sweetwater can’t imagine plugging into an H&K TubeMeister 18 head or combo without this footswitch — you can’t take full advantage of its wide-ranging tone without it! General Features: A perfect match for the TubeMeister 18 head or combo Per-channel LED indicators provide at-a-glance confirmation of what’s going on 15-foot cable Rugged build quality Tech Specs: Type: Hughes & Kettner Amp Footswitch Compatibility: Hughes & Kettner TubeMeister Number of Footswitch Buttons: 2 Cable Included: Yes, 15 ft. TRS Cable Manufacturer Part Number: HKFS2RD Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Hughes & Kettner HKFS1 Footswitch for Electric Guitar Amplifiers The Hughes & Kettner FS-1 is a footswitch designed for use with compatible guitar amplifiers. It's a latching footswitch, meaning it will actuate the connected effect upon activation, and leave it engaged until you press the footswitch again. This footswitch utilizes a 1/4" connection, and sports an LED that's phantom powered by your corresponding amplifier. General Features: For Use with Guitar Amplifiers Latching Footswitch 1/4" Connection Phantom-Powered LED Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Hughes & Kettner ERA2/WD ERA 2 400-watt Acoustic Combo Amp - Wood The Hughes & Kettner era 2, like its predecessor the era 1, is a bold, beautifully designed combo acoustic amplifier that brings 400 watts of natural-sounding tone, excellent dynamic response, and impressive headroom to whatever acoustic instrument you use. The increase in wattage on the era 2 means more robust low end coming from two 8" speakers and a single 1" dome tweeter. This speaker setup makes the era 2 ideal for percussive playing styles, as well as double basses and acoustic basses. It also pairs beautifully with external music devices and drum machines. The era 2 is also a full-range PA system with two fully loaded channels — 1 and 2 — that can be tailored to voice and instrument for stellar live performance. In addition, Channel 3 can be used for external devices like smartphones and MP3 players, while Channel 4 can be used for line-level devices, such as mixers and drum machines. Acoustic instrumentalists here at Sweetwater have fallen in love with the era 2 for its diverse array of effects and stellar amplified tone. General Features: Built with top-shelf components, including detailed preamps, premium AD/DA, and a custom-made power amp Delivers natural-sounding tone, excellent dynamic response, and impressive headroom at 400 watts 2 independent FX engines with 16 great-sounding algorithms Preshape and Mode buttons conform to your voice or instrument, optimizing it for maximum impact Doubles as a full-range PA system that lends magical presence to vocals and backing tracks 1/8" auxiliary input that's ideal for patching in your tablet, smartphone, or media player FX loop for integrating your favorite external effects Tech Specs: Type: Acoustic Combo Amp Number of Channels: 4 Output Power: 400W Speakers: 2 x 8" Custom woofers, 1 x 1" Dome tweeter Stereo: Yes Inputs: 2 x XLR-1/4" combo, 1 x 1/8" (aux) Phantom Power: Yes Outputs: 1 x XLR (DI), 1 x 1/4" (line), 1 x S/PDIF (TOSLINK), 1 x 1/4" (tuner) Effects Loop: Yes EQ: 3-band EQ (channel 1, 2) Reverb: Room, Hall, Church Effects: Delay, Chorus, Flanger Feedback Control: Yes, Notch Filter Control Footswitch I/O: 1 x 1/4" (amp mute, internal fx mute) Footswitch Included: No Power Source: Standard IEC AC cable Height: 18.7" Width: 13.77" Depth: 11.41" Weight: 31.1 lbs. Manufacturer Part Number: ERA2/WD Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Hughes & Kettner ERA2/BK ERA 2 400-watt Acoustic Combo Amp - Black The Hughes & Kettner era 2, like its predecessor the era 1, is a bold, beautifully designed combo acoustic amplifier that brings 400 watts of natural-sounding tone, excellent dynamic response, and impressive headroom to whatever acoustic instrument you use. The increase in wattage on the era 2 means more robust low end coming from two 8" speakers and a single 1" dome tweeter. This speaker setup makes the era 2 ideal for percussive playing styles, as well as double basses and acoustic basses. It also pairs beautifully with external music devices and drum machines. The era 2 is also a full-range PA system with two fully loaded channels — 1 and 2 — that can be tailored to voice and instrument for stellar live performance. In addition, Channel 3 can be used for external devices like smartphones and MP3 players, while Channel 4 can be used for line-level devices, such as mixers and drum machines. Acoustic instrumentalists here at Sweetwater have fallen in love with the era 2 for its diverse array of effects and stellar amplified tone. General Features: Built with top-shelf components, including detailed preamps, premium AD/DA, and a custom-made power amp Delivers natural-sounding tone, excellent dynamic response, and impressive headroom at 400 watts 2 independent FX engines with 16 great-sounding algorithms Preshape and Mode buttons conform to your voice or instrument, optimizing it for maximum impact Doubles as a full-range PA system that lends magical presence to vocals and backing tracks 1/8" auxiliary input that's ideal for patching in your tablet, smartphone, or media player FX loop for integrating your favorite external effects Tech Specs: Type: Acoustic Combo Amp Number of Channels: 4 Output Power: 400W Speakers: 2 x 8" Custom woofers, 1 x 1" Dome tweeter Stereo: Yes Inputs: 2 x XLR-1/4" combo, 1 x 1/8" (aux) Phantom Power: Yes Outputs: 1 x XLR (DI), 1 x 1/4" (line), 1 x S/PDIF (TOSLINK), 1 x 1/4" (tuner) Headphones: 1 x 1/4" Effects Loop: Yes EQ: 3-band EQ (channel 1, 2) Reverb: Yes Effects: Delay, Chorus, Flanger Feedback Control: Yes, Notch Filter Control Footswitch I/O: 1 x 1/4" (amp mute, internal fx mute) Footswitch Included: No Height: 18.7" Width: 13.77" Depth: 11.41" Weight: 31.9 lbs. Manufacturer Part Number: ERA2/BK Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Hughes & Kettner ERA1/WD ERA 1 250-watt Acoustic Combo Amp - Wood The Hughes & Kettner era 1 uses top-shelf components — detailed preamps, premium AD/DA, and a custom-made power amp — to deliver natural-sounding tone, excellent dynamic response, and impressive headroom. This acoustic combo is more than a simple guitar amplifier, it's also a full-range PA system that lends magical presence to vocals and backing tracks. Channels 1 and 2 are fully loaded — use the Preshape and Mode buttons to tailor each channel to your voice or instrument, then add extra polish with 16 internal effects. You also get two more channels for break music, external effects, and more. The era 1 is also lightweight and easy to transport, making it a gig-worthy investment. General Features: Built with top-shelf components, including detailed preamps, premium AD/DA, and a custom-made power amp Delivers natural-sounding tone, excellent dynamic response, and impressive headroom Two independent FX engines with 16 great-sounding algorithms Preshape and Mode buttons conform to your voice or instrument, optimizing it for maximum impact Doubles as a full-range PA system that lends magical presence to vocals and backing tracks 1/8" auxiliary input that's ideal for patching in your tablet, smartphone, or media player FX loop for integrating your favorite external effects Compact and as light as a conventional 60-watt combo for easy transport Tech Specs: Type: Acoustic Combo Amp Number of Channels: 4 Output Power: 250W Speakers: 1 x 8" woofer, 1 x 1" dome tweeter Inputs: 2 x XLR-1/4" combo, 1 x 1/8" (aux) Phantom Power: Yes Outputs: 1 x XLR (DI out), 1 x 1/4" (line out), 1 x 1/4" (headphones), 1 x 1/4" (tuner), 1 x Toslink (S/PDIF), 1 x 1/4" (tuner) EQ: 3-band EQ Reverb: Room, Hall, Church Effects: Delay, Chorus, Flanger Footswitch I/O: 1 x 1/4" (FS-2 sold separately) Construction Material: Stained Wood cabinet Power Source: Standard IEC AC cable Height: 11.2" Width: 13.8" Depth: 11.4" Weight: 21.7 lbs. Manufacturer Part Number: ERA1/WD Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Hughes & Kettner ERA1/BK ERA 1 250-watt Acoustic Combo Amp - Black The Hughes & Kettner era 1 uses top-shelf components — detailed preamps, premium AD/DA, and a custom-made power amp — to deliver natural-sounding tone, excellent dynamic response, and impressive headroom. This acoustic combo is more than a simple guitar amplifier, it's also a full-range PA system that lends magical presence to vocals and backing tracks. Channels 1 and 2 are fully loaded — use the Preshape and Mode buttons to tailor each channel to your voice or instrument, then add extra polish with 16 internal effects. You also get two more channels for break music, external effects, and more. The era 1 is also lightweight and easy to transport, making it a gig-worthy investment. General Features: Built with top-shelf components, including detailed preamps, premium AD/DA, and a custom-made power amp Delivers natural-sounding tone, excellent dynamic response, and impressive headroom Two independent FX engines with 16 great-sounding algorithms Preshape and Mode buttons conform to your voice or instrument, optimizing it for maximum impact Doubles as a full-range PA system that lends magical presence to vocals and backing tracks 1/8" auxiliary input that's ideal for patching in your tablet, smartphone, or media player FX loop for integrating your favorite external effects Compact and as light as a conventional 60-watt combo for easy transport Tech Specs: Type: Acoustic Combo Amp Number of Channels: 4 Output Power: 250W Speakers: 1 x 8" woofer, 1 x 1" dome tweeter Inputs: 2 x XLR-1/4" combo, 1 x 1/8" (aux) Phantom Power: Yes Outputs: 1 x XLR (DI out), 1 x 1/4" (line out), 1 x 1/4" (headphones), 1 x 1/4" (tuner), 1 x Toslink (S/PDIF), 1 x 1/4" (tuner) EQ: 3-band EQ Reverb: Room, Hall, Church Effects: Delay, Chorus, Flanger Footswitch I/O: 1 x 1/4" (FS-2 sold separately) Construction Material: Black Tolex Power Source: Standard IEC AC cable Height: 11.2" Width: 13.8" Depth: 11.4" Weight: 23.7 lbs. Manufacturer Part Number: ERA1/BK Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Hughes & Kettner STOMPMAN StompMan Guitar 50-watt Amplifier Pedal If you're anything like the Sweetwater guitarists who buck the backbreaking heads and cabs in favor of convenience without tonal compromise, the Hughes & Kettner StompMan guitar amplifier pedal is fully prepared to serve as the centerpiece of your rig. Though sized to fit easily on most pedalboards, the StompMan's tone is nothing short of massive, with up to 50 watts on tap to serve you well in both studio and stage situations. Familiar amp controls like Gain, Presence, Resonance, and Tone fine-tune your sound to perfection, with a Sagging control front and center to adjust compression and overtone levels to taste. When it's time to bust out that searing solo, a built-in boost in the form of a Solo footswitch adds up to 6dB of gain in an instant. For all-tube tone at your feet, consider Hughes & Kettner's StompMan Guitar Amplifier Pedal for your next live performances! General Features: Single-channel guitar amp in a pedalboard-friendly format 50 watts at 4 ohms, 25 watts at 8 ohms, and 12.5 watts at 16 ohms Fully analog Spirit Tone Generator circuit delivers tube-like tone at your feet Classic amp controls like Gain, Presence, Resonance, and Tone tweak your sound to perfection Sagging knob adjusts power amp compression to retain your ideal tone at all volumes Footswitchable Solo function engages up to 6dB boost; Solo Vol. knob around back adjusts level Footswitchable FX Loop function makes it easy to incorporate other pedals; toggle around back swaps between Bypass and FX Loop modes Tech Specs: Type:    Solid StateNumber of Channels:    SingleTotal Power:    50W @ 4 ohms, 25W @ 8 ohms, 12.5W @ 16 ohmsEQ:    Tone control, Presence, ResonanceInputs:    1 x 1/4" (instrument), 1 x 1/4" (return)Outputs:    1 x 1/4" (4-16 ohms), 1 x 1/4" (send/line out)Effects Loop:    YesPower Source:    24V DC 2.5A power supply (included)Height:    2.04"Width:    5.19"Depth:    6.02"Weight:    1.43 lbs.Manufacturer Part Number:    STOMPMAN Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Hughes & Kettner AMPMAN/CLASSIC AmpMan Classic 50-watt Guitar Amplifier Pedal The Hughes & Kettner AmpMan Classic redefines the pedalboard-only guitar rig. Thanks to H&K's analog Spirit Tone Generator, this 50-watt, floorboard-style amplifier offers epic tube-like tone at any volume with zero digitizing of your signal. You get two independent channels that cover the spectrum of vintage-inspired clean and classic crunch sounds, with independent Gain, Tone, Presence, Resonance, Sagging, and Volume controls for each. This feature-laden amplifier pedal includes footswitchable boost and solo functions, plus an effects loop and noise gate. You also get a built-in Red Box cabinet emulator, a stereo headphones output, and an auxiliary input. Best of all, everything is accessible via the AmpMan Classic's onboard knobs and switches — no menu diving required. Whether you're recording direct, plugging into a cab, or going live into a PA system, you can expect top-notch tone and performance from the H&K AmpMan Classic pedal guitar amplifier. Note: This device is intended to drive a speaker cabinet and should not be placed in front of an amplifier or pedals. General Features: 50W, 2-channel floorboard-style guitar amplifier Spirit Tone Generator offers tube-like tone at any volume with zero digitizing of your signal Channel 1 unleashes vintage-inspired cleans, plus sizzling blues textures Channel 2 produces '70s- and '80s-era rock crunch Per-channel sound-shaping controls: Gain, Tone, Presence, Resonance, Sagging, and Volume Sagging control fine-tunes power amp saturation and compression independent of volume Footswitchable Boost adds extra hair to your signal when the situation calls for it Footswitchable Solo function gives you a 0 to +6dB boost over your Master knob's setting Footswitchable serial effects loop makes integrating your stompboxes and processors a breeze Black Spirit 200-derived IDB gate provides a whisper-quiet noise floor between notes Red Box AE+ cabinet emulator achieves miked-cab sounds without a mic or a cab Separately adjustable headphones output and auxiliary input Everything is accessible via onboard knobs and switches — no menu diving required Tech Specs: Type: Solid State Number of Channels: 2 Output Power: 50W @ 4 ohms EQ: Tone, Presence, Resonance Amp Modeling: Red Box AE+ Cabinet Emulator Number of Models: 8 x Cabinet Emulations Inputs: 1 x 1/4", 1 x 1/8" (aux) Outputs: 1 x XLR (cab emulation DI), 1 x 1/4" (4-16 ohms) Headphones: 1 x 1/8" Effects Loop: Yes Footswitch I/O: Built-in (channel, boost, loop, solo) Features: IDB Noise Gate Power Source: 24V DC power supply Height: 2.04" Width: 9.84" Depth: 6.02" Weight: 2.53 lbs. Manufacturer Part Number: AMPMAN/CLASSIC Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Hughes & Kettner TRIAMP3H TriAmp Mark 3 150-watt Dual 3-channel Programmable Tube Head Get all the true tube tones you want and all the stage-rumbling wattage you need! The Hughes & Kettner Triamp MKIII head comes equipped with a trio of independent power amp sections that can be used independently or combined. The best part? You can use a wide range of different tube types to conjure authentic American and British amp tones (and create your own custom sounds, too). Each of the Triamp MKIII's three preamp sections has a pair of channels, and you can route them independently to the power sections. The result? You're plugged into 42 different amp possibilities - all from one amp head. You also get a DI output with Ambience Emulation, full MIDI control, an included MIDI footboard, intuitive controls, an onboard noise gate, and much more. General Features: 150-watt all-tube amp 6 channels - 1A: 50s Californian clean; 1B: 60s British clean; 2A: 70s British lead; 2B: 80s brown sound; 3A: 90s Californian high-gain; 3B: modern high-gain and beyond Threedom Power Amp Technology: 3 pairs of freely assignable power tubes Tech Specs: Type: Tube Number of Channels: 6 Output Power: 150W Preamp Tubes: 1 x 7025/E83CC, 1 x 12AX7A-C, 7 x ECC83 Power Tubes: 2 x EL34, 4 x 6L6 EQ: 3-band Inputs: 1 x 1/4" (Instrument), 1 x 1/4" (Power Amp) Outputs: 1 x 1/4" (Preamp), 1 x XLR (DI) Effects Loop: Yes MIDI I/O: In/Out/Thru Footswitch I/O: 1 x 7-pin DIN (presets, stomp box mode, channel, boost) Footswitch Included: Yes, 7-button footswitch Construction Material: Black Textured Vinyl Power Source: Standard IEC AC cable Height: 15.47" Width: 29.13" Depth: 10" Weight: 48.5 lbs. Manufacturer Part Number: TRIAMP3H Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.