Car EQs & Sound Processors (89)

Power Acoustik PWM-5V 5-Band Parametric Equalizer w/ Subwoofer Control Maybe you’ve got an older car audio system from which you want to get more. Perhaps you’ve got an all-new setup that you want to get the maximum potential. In either case, Power Acoustik’s NEW PWM-5V has (5) bands of equalization that’ll let you fine-tune your sound, along with independent master volume, subwoofer level, and fader controls’ll maintain your highs and lows in balance.The PWM-5V features RCA inputs so that you can connect them to your aftermarket system. The RCA outputs ensure that your amplifiers get a clean, powerful signal for maximum performance. You will also notice this particular Equalizer has a built-in Voltage-Level Indicator. General Features: Power Supply: 11-15 DC Max Output Voltage: 8.5V RMS Frequency Response: 10-50 kHz ± 1 dB Equalization Range: ± 12 dB Subwoofer Crossover Frequency: 43-60 Hz Input Impedance: 20K Ohms Output Impedance: 2K Ohms S/N Ratio: 80 dB Ref. 1V Input T.H.D.: 0.05% SIZE: 7″L x 4.25″W x 1.25″H ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Crunch Ground Pounder CREQ7B 7-Band Parametric Equalizer       Item Description Parametric Equalizer : 50Hz, 125Hz, 315Hz, 750Hz, 2.2KHz, 12KHz Boost/Cut Range : ± 18dB S/N Ratio: 90dB Frequency Response : 25Hz-50KHz Power Source: 10-14.4V Input Current : .05A Max Distortion : 0.01% THD at 1V Output Frequency Response : 10Hz-30KHz ±3dB Output Level : +16 dB Separation : >60dB Bass Adjust : ±10dB Mid Adjust : ±10dB Treble Adjust: ±10dB Sub Bass : 43Hz & 60z SD/USB : No     ⚠️Warning Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Crunch Ground Pounder CRXR 2-way/3-way active x-over with bass remote control.       Item Description This model operates as either a 2 or 3-way crossover with an 18dB/ Octave subwoofer crossover with remote gain control module. This unit will provide filtered signals to front and rear amplifiers, and Low Pass subwoofer output using a single pair of inpouts. Features:Bass boosted with Quasi-Parametric EqualizationDC/DC Regulated Switching power supplyFrequency MultiplierRear Input SwitchFront/Rear Inputs with Front/Rear/Sub OutputsAdjustable Output level controlStereo/Mono Subwoofer Control SwitchRemote Level Control via Under-Dash Module     ⚠️Warning Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Hifonics BXiPro3.0 Digital Bass Processor Epicenter 2CH Hi/Lo Converter w/ Noise Reduction The Hifonics BXiPRO3.0 Digital Bass Enhancement Processor integrates with an upgraded subwoofer system into any vehicle. Showcasing a compact design with a sleek finish, this all-in-one processor gives you 3x the power at half the size in space. With adjustable mounting solutions and multipoint installation options, including placing the processor behind dash-concealed locations, this processor will be as flexible as your installation demands. With rugged, reinforced connectors that feature Tiffany Style differential noise inputs, you’ll not only receive a processor that has superior connectivity where you need it the most, but you’ll also embrace selectable multilevel inputs and dual remote outputs (high-levels out and sub-levels out) that connect 2 different amplifiers. This processor also comes with a wired, adjustable, dash-mountable remote. General Features: BXiPro Bass Enhancer Processor with Dash Mount Remote Control Enhances and restores the bass level Screw-in power and speaker connectors to chassis for secure connections that prevent disconnection Dual-function bass remote Remote wire input, DC sense, and music sense turn on Input and output signal clip indicators Mono adjustable output level (can be controlled by bass remote) 48v high-level inputs Ability to use test tones to set input and output levels Fine-tuning adjustability using bass width and sweep Fixed 4v full range output Small profile Tiffany-style RCA connectors Low and high-level audio inputs (speaker-level inputs) Balanced differential inputs (for noise reduction) Authorized Internet Dealer 1-year Manufacturer's Warranty Functions & Operations: Adjustable bass enhancement preamp output Bass remote input Preamp full range output Adjustable bass level output Adjustable bass width and sweep adjustments Output level control with clip indicators Input level control with clip indicators Selectable input level range (RCA or speaker level) Selectable turn on the trigger (remote wire input, DC sense, and signal sense) Low-level inputs (RCA level) High-level input (speaker level) Power connector with two remote output trigger wires Dual concentric bass knob (A. bass level, B. output level) Product Specifications: Fuse value: 1A mini ATC Voltage range: 9.5V -15V Bass remote type: HF-U-02 Fixed voltage output full range: 4V Adjustable subwoofer output voltage: 0V -9V Maximally Flat Frequency Response Main: (-3dB) 10Hz to >50kHz Input Impedance Low-level inputs: 20k Ohms Input Impedance High-level inputs: 20k Ohms Maximum high-level Input Voltage on any input before clipping: >48V Maximum Output voltage at 1.0% THD+N (subwoofer output): 9.0V Signal to Noise Ratio (ref to 2Vrms out, unity gain): -84.0dBA EQ boost: Variable to +8.1dB Unit turn on options: 30mV High-Level Audio, 59mV RCA Audio, 2.2V DC Offset Current Draw: 0.32A Turn on Delay Time: 0.1 seconds Setup test tone track: 100 Hz & 1000Hz Dimensions: 109mm W x134mm D x 30.5mm H Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

AudioControl LC7i 6-channel line output converter with bass restoration adds aftermarket subs and amps to a factory system (Black)+ Free Absolute Electrical Tape+ Phone Holder Want to add your own speakers, subs, and amps to a factory system? AudioControl's LC7i 6-channel line output converter (LOC) with bass restoration allows you to add aftermarket amps, speakers, and subs to your car's factory radio, so you can enjoy better and more powerful sound without losing climate controls, voice-activated functions, or other built-in factory features. The LC7i accepts speaker-level signals, so you can use it with just about any setup, even high-powered amplified systems. Summing The LC7i sums its input signals together, even if they've been crossed over for tweeters, mids, and subs by the factory system. That way, you can count on a strong, smooth, full-range signal for your processors and amps. The LC7i features six RCA preamp outputs that'll handle a traditional front/rear/sub setup. Why you have to restore the bass Many factory radios actually turn the bass down as you increase the volume to protect the cheap factory speakers, subsequently removing much of your music's power and punch. AudioControl developed a patent pending AccuBASS™ circuit that restores the bass the factory radio erased, giving you much fuller and more enjoyable sound. The AccuBASS is applied to the subwoofer output channel, so your sub amp can have the entire, restored signal to work with. Level-matching with an LED indicator AudioControl makes it easy: set your factory stereo to about 3/4 maximum volume, turn the output level control of the LC7i until the "Maximized" light begins to flicker, then adjust the gain controls on your amps and you're done. You've level-matched the output of your receiver to the amplifier's input, so you can count on getting maximum performance and minimum noise from your system. Convenience The optional dash-mounted ACR-1 wired remote allows you to adjust the volume of the bass while you're on the go. The speaker-level inputs sense incoming signals and turn on the LC7i, while a built-in 12-volt trigger turns on your amps as well. If your factory system only has channels for front and rear speakers, AutoMode™ will create the output you can use for your subs Product highlights: 6-channel line output converter plus bass restoration 6 speaker-level inputs (each can handle up to 400 watts RMS) internal channel summing AccuBASS™ bass restoration circuitry 6 preamp outputs (up to 8.5 volts RMS) level matching controls with Maximized Indicator LED Other Features: optional wired remote subwoofer level controller available (#161ACR1) AutoMode™ turns 4-channel input to 6-channel output GTO™ signal-sensing turn on 12-volt turn-on lead output recommended fuse rating: 2 amps 8-11/16"W x 1-3/8"H x 6-9/16"D warranty: 5 years 6-Channel line output converter (black) Owner's manual QC checklist Absolute BT1700 Vinyl Electrical Tape is good quality, multi-purpose vinyl insulating tape. It has great resistance to moisture and varying weather conditions. It is a polyvinyl chloride (PVC) tape that is flame-retardant and conformable. Details Resists abrasion, moisture, alkalis, solvents, and acids Flame-retardant and inhibits the corrosion of electrical conductors Made of durable PVC Compatible with rubber and synthetic splicing compounds Withstands a temperature range of 32 to 194 °F (0 to 90 °C) UL Listed, CSA and VDE Certified Specifications Adhesive Type Rubber Application Insulation Brand Absolute Elongation at Break 200 % Maximum Operating Temperature (Celsius) 90 Degree Celsius Maximum Operating Temperature (Fahrenheit) 194 Degree Fahrenheit Minimum Operating Temperature (Fahrenheit) 32 Degree Fahrenheit Overall Length (Imperial) 60 ft Overall Length (Metric) 18 m Overall Width (Imperial) 0.75 in Overall Width (Metric) 19 mm Product Color Black Shelf Life 5 Year Tape Grade General Use ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

AudioControl LC7i 6-channel line output converter with bass restoration adds aftermarket subs and amps to a factory system (Black) Want to add your own speakers, subs, and amps to a factory system? AudioControl's LC7i 6-channel line output converter (LOC) with bass restoration allows you to add aftermarket amps, speakers, and subs to your car's factory radio, so you can enjoy better and more powerful sound without losing climate controls, voice-activated functions, or other built-in factory features. The LC7i accepts speaker-level signals, so you can use it with just about any setup, even high-powered amplified systems. Summing The LC7i sums its input signals together, even if they've been crossed over for tweeters, mids, and subs by the factory system. That way, you can count on a strong, smooth, full-range signal for your processors and amps. The LC7i features six RCA preamp outputs that'll handle a traditional front/rear/sub setup. Why you have to restore the bass Many factory radios actually turn the bass down as you increase the volume to protect the cheap factory speakers, subsequently removing much of your music's power and punch. AudioControl developed a patent pending AccuBASS™ circuit that restores the bass the factory radio erased, giving you much fuller and more enjoyable sound. The AccuBASS is applied to the subwoofer output channel, so your sub amp can have the entire, restored signal to work with. Level-matching with an LED indicator AudioControl makes it easy: set your factory stereo to about 3/4 maximum volume, turn the output level control of the LC7i until the "Maximized" light begins to flicker, then adjust the gain controls on your amps and you're done. You've level-matched the output of your receiver to the amplifier's input, so you can count on getting maximum performance and minimum noise from your system. Convenience The optional dash-mounted ACR-1 wired remote allows you to adjust the volume of the bass while you're on the go. The speaker-level inputs sense incoming signals and turn on the LC7i, while a built-in 12-volt trigger turns on your amps as well. If your factory system only has channels for front and rear speakers, AutoMode™ will create the output you can use for your subs Product highlights: 6-channel line output converter plus bass restoration 6 speaker-level inputs (each can handle up to 400 watts RMS) internal channel summing AccuBASS™ bass restoration circuitry 6 preamp outputs (up to 8.5 volts RMS) level matching controls with Maximized Indicator LED Other Features: optional wired remote subwoofer level controller available (#161ACR1) AutoMode™ turns 4-channel input to 6-channel output GTO™ signal-sensing turn on 12-volt turn-on lead output recommended fuse rating: 2 amps 8-11/16"W x 1-3/8"H x 6-9/16"D warranty: 5 years 6-Channel line output converter (black) Owner's manual QC checklist ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

AudioControl LC2i PRO 2-channel line output converter+ Free Absolute Electrical Tape+ Phone Holderr High-level input line output converter More and more aftermarket amplifier installations depend on using the factory amp's powered outputs for its inputs. AudioControl's LC2i PRO line output converter takes amplified speaker-level signals and converts them into high-quality preamp signals that can then be fed to another processor, a full-range amplifier, or your subwoofer amp. Bass feature Some factory radios dial down the bass as you turn up the volume to protect the flimsy factory speakers. The problem is, they don't give it back when you upgrade to a nice set of aftermarket speakers. AudioControl packs the LC2i PRO with their AccuBASS™ circuitry that reverses the factory low-frequency roll-off, giving you the bass you need to enjoy your music to the fullest. Installation conveniences The included dash-mount wired remote control allows you to adjust the level of your sub channel on the go. Load selection switches make OEM integration easier, so the LC2i PRO will work with almost any factory sound system. Selectable turn-on modes include GTO™ Signal Sense (DC offset), audio sense, or remote 12 volt inputs. Product highlights: 2-channel active line output converter ACR-1 wired remote bass level control included 2 speaker-level inputs with 40-volt (400 watts RMS) power handling Main and Bass preamp-level outputs (up to 9.5 volts) Main and Bass output controls for level matching adjustable AccuBASS corrects for factory bass roll-off More Info: selectable turn-on options: GTO signal Sense (DC offset), audio sense, or remote 12 volt input 12-volt turn-on lead output recommended fuse rating: 1 amp dimensions: 6-15/16"W x 1"H x 3"D weight: 0.75 pound warranty: 5 years Two-Channel line output converter Two 4-pin captive-screw connectors (installed) ACR-1 Level control 16.5' Level-control cable (RJ-14) Quickstart guide (on cardboard label) Absolute BT1700 Vinyl Electrical Tape is good quality, multi-purpose vinyl insulating tape. It has great resistance to moisture and varying weather conditions. It is a polyvinyl chloride (PVC) tape that is flame-retardant and conformable. Details Resists abrasion, moisture, alkalis, solvents, and acids Flame-retardant and inhibits the corrosion of electrical conductors Made of durable PVC Compatible with rubber and synthetic splicing compounds Withstands a temperature range of 32 to 194 °F (0 to 90 °C) UL Listed, CSA and VDE Certified Specifications Adhesive Type Rubber Application Insulation Brand Absolute Elongation at Break 200 % Maximum Operating Temperature (Celsius) 90 Degree Celsius Maximum Operating Temperature (Fahrenheit) 194 Degree Fahrenheit Minimum Operating Temperature (Fahrenheit) 32 Degree Fahrenheit Overall Length (Imperial) 60 ft Overall Length (Metric) 18 m Overall Width (Imperial) 0.75 in Overall Width (Metric) 19 mm Product Color Black Shelf Life 5 Year Tape Grade General Use ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

AudioControl The Epicenter Digital Bass Restoration Processor You like all the bumpin' bass you hear in hip hop, rap, and EDM? Well you can put that deep, biting bass into any kind of music — from classical, jazz, and rock to folk and Tejano — with an AudioControl Epicenter bass restoration processor. Most factory radios dial down bass response to protect flimsy speakers, so when you do add a subwoofer, there's no bass to play. The Epicenter will bring it back. AudioControl's legendary Epicenter bass processor maximizes the low-frequency power and punch of your bass system, whether it's a simple powered bass tube or a full-blown competition setup. Simply install this processor between your receiver and your amplifiers or crossovers, and you'll finally be able to hear all the good bass you've been missing. An included wired remote lets you control the amount of thump from the front seat. How does it do it? Sophisticated processing analyzes the incoming signal and synthesizes low-bass fundamental tones, increasing bass response tremendously. The Epicenter connects to any receiver with preamp outputs — its balanced inputs will reject noise from your car's electrical system. A subsonic filter removes extreme low frequencies from your signal so your amps and subs will play more efficiently, while a single band ParaBass equalizer lets you fine-tune the bass tone. Upgrade available AudioControl's Epicenter bass restoration processing is also available in The Epicenter Micro, which features a compact chassis, high-level inputs, and selectable load resistors for better OEM factory system integration. Product highlights: bass restoration processor increases bass response from your system 2-channel preamp inputs and outputs Para-Bass controls adjust center-frequency and width of bass EQ processing fixed subsonic filter (33 Hz, 12/dB octave) wired remote bass level controller frequency response: 10 to 100,000 Hz fuse rating: 1A 8-1/16"W x 1-1/4"H x 6-3/4"H warranty: 5 years Pre-amp Bass Restoration Processor (black) Remote dash mount control 20' RJ-14 cable Owner's manual QC checklist ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

AudioControl LC2i PRO 2-channel line output converter with AccuBASS™ High-level input line output converter More and more aftermarket amplifier installations depend on using the factory amp's powered outputs for its inputs. AudioControl's LC2i PRO line output converter takes amplified speaker-level signals and converts them into high-quality preamp signals that can then be fed to another processor, a full-range amplifier, or your subwoofer amp. Bass feature Some factory radios dial down the bass as you turn up the volume to protect the flimsy factory speakers. The problem is, they don't give it back when you upgrade to a nice set of aftermarket speakers. AudioControl packs the LC2i PRO with their AccuBASS™ circuitry that reverses the factory low-frequency roll-off, giving you the bass you need to enjoy your music to the fullest. Installation conveniences The included dash-mount wired remote control allows you to adjust the level of your sub channel on the go. Load selection switches make OEM integration easier, so the LC2i PRO will work with almost any factory sound system. Selectable turn-on modes include GTO™ Signal Sense (DC offset), audio sense, or remote 12 volt inputs. Product highlights: 2-channel active line output converter ACR-1 wired remote bass level control included 2 speaker-level inputs with 40-volt (400 watts RMS) power handling Main and Bass preamp-level outputs (up to 9.5 volts) Main and Bass output controls for level matching adjustable AccuBASS corrects for factory bass roll-off More Info: selectable turn-on options: GTO signal Sense (DC offset), audio sense, or remote 12 volt input 12-volt turn-on lead output recommended fuse rating: 1 amp dimensions: 6-15/16"W x 1"H x 3"D weight: 0.75 pound warranty: 5 years Two-Channel line output converter Two 4-pin captive-screw connectors (installed) ACR-1 Level control 16.5' Level-control cable (RJ-14) Quickstart guide (on cardboard label) ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

AudioControl The Epicenter® Micro Bass restoration processor and line output converter Add bass to your aftermarket system's high-level sourceMost factory radios dial down deep, low-hitting bass notes to protect flimsy factory speakers. The Epicenter Micro from AudioControl takes amplified speaker-level signals, converts them into the high-quality preamp signals your sub amp needs, and then adds the bass that's missing. Even when listening to traditionally bass-weak classical, jazz, folk, or Tejano music, you'll finally be able to hear all the good bass you've been missing How does it do it? Sophisticated processing analyzes the incoming signal and synthesizes low-bass fundamental tones, increasing bass response tremendously. A single band ParaBASS® equalizer lets you fine-tune your subwoofer's tone. A selectable subsonic filter removes extreme low frequencies so your amps and subs will play more efficiently. The Epicenter Micro will also connect to any receiver with preamp outputs — its balanced inputs will reject noise from your car's electrical system for ultra-clean output. Installation conveniences The included ACR-4 dash-mount wired remote control allows you to adjust the level of your sub channel on the go. Load selection switches make OEM factory system integration easier, so The Epicenter Micro will work with almost any vehicle's sound system. Selectable turn-on modes include GTO™ Signal Sense (DC offset), audio sigal , or remote 12-volt input. Product highlights: active 2-channel line driver/output converter with bass restoration designed to work with aftermarket and factory systems provides up to 9.5 Vrms output (selectable level: 5, 7, 10V) preamp and speaker-level inputs speaker-level inputs handle up to 40V (400 watts RMS) speaker-level inputs feature switchable load resistance (20, 60, or 20,000 ohms) to prevent factory stereo shut-down Epicenter bass restoration increases bass response Para-Bass controls adjust center-frequency and width of bass EQ processing More info: ACR-4 wired remote included switchable Programmable Frequency Match (PFM) subsonic filter (20 Hz, 12/dB octave) selectable ground isolation helps eliminate noise auto turn-on via 12V remote, DC offset, or audio signal detect 12-volt turn-on lead output wiring, fuse, and hardware not included with device 18-gauge power and ground leads and a 1-amp fuse recommended dimensions: 5-1/8" W x 1" H x 3" D warranty: 5 years ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov