Electronics (567)

Alpine R-S69.2 600W Peak, 200W RMS R-Series 6x9 Inch Coaxial 2-Way Speakers + METRA 72-8104   R-Series speakers give you power and control. With an innovative material that delivers more output, the speakers produce a dependable performance for a loud and fun experience. If you play your music loud and want others to know, the R-Series speakers are the match for you. You’ll enjoy a center sound stage with speakers that play loud and clear without distortion. The R-Series speakers are tuned with an emphasis on the high- and low-end frequencies, so they deliver power while naturally producing bright, active sound. They are the perfect power and performance match for the R-Series subwoofers and amplifiers. The woofers have a large, 35-millimeter (mm) voice coil which allows for more coil windings to fit in the gap. This results in greater heat dissipation and increased power handling, for superior control and output. General Features: Alpine R-S69.2 R-Series 6x9 Inch Coaxial 2-Way Speakers Power Handling: RMS: 100 Watts Peak: 300 Watts Impedance: 4 Ohm Carbon-fiber reinforced polymer (CFRP) woofer Carbon-fiber reinforced polymer dome tweeter Frequency response: 60 Hz - 40 kHz Sensitivity: 90 dB Top-mount depth: 2-7/8" Grilles included Authorized Dealer 1-year Manufacturer's Warranty What's in the box: Two 2-way Speakers 2 Bottom mount brackets 2 Grilles 2 Grille badges Eight 1-1/8" Screws Eight M4x60mm Machine screws (with split lock washers attached) 8 Split lock washers 8 Flat washers Eight M4 Hex nuts 8 Speed clips Warranty information Important Notice Online product registration information Template and specs on the box Alpine R-S69.2 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Metra 99-9107B Compatible Fits for select 2002-09 Audi A4 and 2004-08 S4 models single or double-dash radios. Fits select 2002-09 Audi A4 and 2004-08 S4 models single- or double-dash radios This mounting kit allows you to install a single-sized (2" tall) or double-sized (4" tall) aftermarket stereo in your vehicle's dash opening.  General Features: Allows for installation of an aftermarket Single-Din or Double-Din car stereo Compatible with select 2002-2009 vehicles from Audi Two sets of our 86-9001 radio removal tool are required to remove the factory radio from the dash Made from the highest quality ABS plastic for an original factory-like fit and finish Includes brackets and hardware parts needed with detailed installation instructions Painted scratch-resistant matte black Authorized Internet Dealer 1-year Manufacturer's Warranty What's in the Package: Radio housing Double-DIN trim-ring Single-DIN trim-ring Pocket 2 Single-DIN brackets 2 Double-DIN brackets Installation Instructions Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

 Alpine S-S57 5x7" Front+Rear Speaker Replacement Kit For 1999-2002 Lincoln Navigator2 Pair ALPINE S-S57 230 Watt 5x7" or 6x8" Coaxial 2-Way Car Audio Speakers. 2 METRA 72-5600 Ford Speaker Wire Harness Connector  Alpine S-S57 460W Max (150W RMS) 6x8/5x7" Type S Series 2-Way Coaxial Car Speakers IT FITS IN MOST COMMON APPLICATIONS To meet the needs of the most common applications in speaker replacement today, we've introduced a 5x7-inch component set to offer newer domestic trucks and cars the ability to upgrade the sound quality of their vehicle. With its innovative technology, this component set makes it a simple solution to getting Alpine sound in many of these vehicles on the road today. INCREASED DRIVING POWER AND CONTROL The S-Series speakers have a large voice coil. The 6.5-inch and 6x9-inch models have a 35-mm voice coil, and this large voice coil size increases their driving power and control of the motor. The S-Series speakers are the first in the industry to use CFRP (Carbon Fiber Reinforced Plastic), a very lightweight yet rigid material. The edges are naturally weaker than the center on a standard, off-the-shelf oval cone due to the elongated shape. Since the CFRP material is directional, it can be manipulated during the molding process to strengthen the areas of the cone that are generally weak. The result is rigidity throughout the cone that delivers accurate and efficient performance. The ability to manipulate the CFRP material during molding is currently exclusive to Alpine and the S-Series speakers. Alpine has three patent-pending procedures in support of this innovative manufacturing process. General Features: 5"x7" S-Type Series TYPE Car Speakers/Component System Peak Power Handling: 460 watts per pair / 230 watts each RMS Power Handling: 150 watts per pair / 75 watts each Carbon fiber reinforced plastic cone Patented HAMR surround 1.1" Silk dome tweeter CTA-2031 compliant speakers 30MM Voice Coil Top-mount Depth: 2-11/32" Cutout Dimensions: 4-15/16" x 7-3/16" 4 ohms impedance Frequency Response: 73 - 22000 Hz Sensitivity: 88dB Authorized Dealer 1-year Manufacturer's Warranty What's in the S-S57 package: S-S57 owner's manual Two 2-way speakers 2 Adapter rings Two 12" Lengths of speaker wire Eight 1-1/4" Screws Eight M4x6mm Machine screws 8 Speed clips Warranty information Online product registration information Important Notice sheet Template and specs on the box  Metra 72-5600 Speaker Connector Harness for Select Ford GM Chevy Lincoln-Mercury Mazda Replacement Harness: Avoid cutting up your factory speaker connectors when installing aftermarket speakers! Our speaker harness adapters are designed to plug directly into the existing factory speaker connector eliminating the guesswork of matching up the correct polarity and they will not affect your factory vehicle warranty. Each package includes 2 harnesses that are needed to install 1 pair of speakers. Compatible WithChevrolet Camaro 2010-2015 Colorado (w/ 7" MyLink radio, RPO code: IOB) 2017 Colorado 2015-2017 Silverado 1500/2500/3500 (w/ 7" MyLink radio, RPO code: IOB) 2016-2017 Silverado 1500 2014-2017 Silverado 2500HD, 3500HD 2015-2017 Suburban 2015-2017 Tahoe 2015-2017 Ford Crown Victoria 1998-2011 Edge 2007-2010 Escape 2008-2012 Escape (w/ out sub) 2004-2007 Escape (seven-speaker system w sub) 2004-2007 Escape Hybrid 2004-2007 Escape 2001-2003 Excursion 2000-2005 Expedition 2007-2014 Expedition Non-NAV 2004-2006 Expedition with factory NAV 2004-2006 Expedition (late production) with factory NAV 2003 Expedition (late production) 2003 Expedition (early production) 2003 Expedition 1999-2002 Expedition (fleet) 2015 Expedition (SSV) 2015 Explorer 2005-2010 Explorer (Audiophile system w sub) 2004-2005 Explorer 2002-2003 Explorer Sport Trac 2001-2010 F-150 2004-2008 F-250/350/450/550 2017 F-250/350/450/550 (with 8.4-inch screen) 2013-2016 F-250/350/450/550 (without 8.4-inch screen) (with CD) 2013-2016 F-250/350/450/550 XL (without CD) 2013-2016 F-250/350/450/550 1999-2012 F-250 1998 F-650/750 (AM/FM/CD) 2016-2017 F-650/750 (AM/FM) 2016-2017 F-650/750 2000-2015 Focus (without MyFordTouch) 2012-2014 Focus 2000-2007 Focus (with Blaupunkt radio) 2003-2004 Freestar 2004-2007 Fusion 2006-2009 Mustang 2010-2014 Mustang (late 2008 build date) 2008-2009 Mustang (early 2008 build date) 2008 Mustang 2005-2007 Ranger 1998-2011 Taurus (without electronic controls) 2000-2007 Taurus (with electronic controls) 2000-2007 Thunderbird 2002-2005 Transit Connect 2010-2011 GMC Canyon (w/ 7" MyLink radio, RPO code: IOB) 2017 Canyon 2015-2017 Sierra 1500/2500/3500 (w/ 7" MyLink radio, RPO code: IOB) 2016-2017 Sierra 1500 2014-2017 Sierra 2500HD, 3500HD 2015-2017 Yukon / Yukon XL 2015-2016 Yukon Denali / Yukon XL Denali 2015-2016 Lincoln Aviator (with NAV) 2003-2005 Aviator (without NAV) 2003-2005 Mark LT 2005-2008 MKX (with NAV) 2007-2010 MKX (without NAV) 2007-2010 MKZ (with NAV) 2007-2009 MKZ (without NAV) 2007-2009 Navigator (with NAV) 2007-2014 Navigator (without NAV) 2003-2014 Navigator (with NAV) (w/ THX audio) 2003-2006 Navigator (with NAV) (w/o THX audio) 2003-2006 Navigator (early production) 2003 Navigator 1999-2002 Town Car (with NAV) 2003-2011 Town Car (without NAV) 2003-2011 Zephyr (with NAV) 2006 Zephyr (without NAV) 2006 Mazda B-Series Pickup 1998-2009 Mazda3 2004-2009 Tribute 2008-2011 Tribute 2001-2006 Mercury Grand Marquis 1998-2010 Marauder 2003-2004 Mariner 2005-2011 Monterey 2004-2007 Mountaineer 2006-2010 Mountaineer(Audiophile system w sub) 2004-2005 Mountaineer(system w/ out factory sub) 2004-2005 Mountaineer 2002-2003 Sable 2008-2009 Sable (no electronic controls) 2000-2006 Sable (electronic controls) 2000-2007 ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

2 Pair Alpine S-S69 520W Max (170W RMS) 6" x 9" Type S Series 2-Way Coaxial Car Speakers + Metra 72-6512 Speaker Harness Connector for Chrysler Vehicles 90-07 Alpine S-S69 520W Max (170W RMS) 6" x 9" Type S Series 2-Way Coaxial Car Speakers FITS IN MOST COMMON APPLICATIONS To meet the needs of the most common applications in speaker replacement today, we've introduced a 6x9-inch component set to offer newer domestic trucks and cars the ability to upgrade the sound quality of their vehicle. With its innovative technology, this component set makes it a simple solution to getting Alpine sound in many of these vehicles on the road today. INCREASED DRIVING POWER AND CONTROL The S-Series speakers have a large voice coil. The 6.5-inch and 6x9-inch models have a 35-mm voice coil, and this large voice coil size increases their driving power and control of the motor. The S-Series speakers are the first in the industry to use CFRP (Carbon Fiber Reinforced Plastic), a very lightweight yet rigid material. The edges are naturally weaker than the center on a standard, off-the-shelf oval cone due to the elongated shape. Since the CFRP material is directional, it can be manipulated during the molding process to strengthen the areas of the cone that are generally weak. The result is rigidity throughout the cone that delivers accurate and efficient performance. The ability to manipulate the CFRP material during molding is currently exclusive to Alpine and the S-Series speakers. Alpine has three patent-pending procedures in support of this innovative manufacturing process. General Features: 6" x 9" Type S Series 2-Way Coaxial Car Speakers Power Handling: Peak: 520 watts per pair / 260 watts each Power Handling: RMS: 170 watts per pair / 85 watts each Recommended Power Range: 10 - 85 watts RMS per channel Carbon Fiber Reinforced Plastic (CFRP) Cone High Amplitude Multi-Roll (HAMR) Surround 1" Silk Dome Tweeter Rubber magnet boot cover CEA-2031 compliant speakers 35mm Voice Coil Top-mount Depth: 2-15/16" Cutout Dimensions: 5-29/32" x 8-3/4" 4 ohms Impedance Frequency Response: 65 - 22000 Hz Sensitivity: 90dB Compatible with the Alpine KTE-S69G Grille Authorized Dealer 1-year Manufacturer's Warranty What is in the S-S69 package: S-S69 owner's manual Two 2-way speakers 2 Bottom mount brackets Two 12" Lengths of speaker wire Eight 1-3/16" Screws Eight M4x60mm Machine screws  Eight M4 Nuts 8 Speed clips 16 Flat washers 8 Split lock washers 8 Spacers Warranty information Online product registration information Important Notice sheet Template and specs on the box (2) Pair of Metra 72-6512 Speaker Wire Adapters for Select Chrysler Vehicles Speaker Harness Connectors Adapters Designed For 1991-Up Chrysler Dodge Jeep Eagle Plymouth, Quick, and Easy Installation, Plug-In The Original Radio Receiver, No Cutting Into Original Wiring Required, High-Quality ABS Plastic Molded Connector For The Perfect Fit, Length: 7" Long. Compatibility List: Chrysler: 1999-2003 300M 1995-2000 Cirrus 1992-1999 Lebaron 1995-2002 LHS 1991-1996 New Yorker 1996-2003 Sebring Coupe 1995-2001 Sebring Sedan 1991-2002 Town & Country 2001-2003 Voyager Dodge: 1991-2003 Caravan 1994-1999 Dakota 1993 Daytona 1998-1999 Durango 1998-2007 Ram Pick Eagle: 1993-1997 Vision Jeep: 1997-2001 Cherokee 1997-2003 Wrangler Plymouth: 1996-2000 Breeze 1995-2001 Neon 1984-2000 Voyager ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-S69 520W Max (170W RMS) 6" x 9" Type S Series 2-Way Coaxial Car Speakers With METRA 72-8104 Speaker Wire Harness Connector Compatible Fit for Toyota FITS IN MOST COMMON APPLICATIONS To meet the needs of the most common applications in speaker replacement today, we've introduced a new 6x9-inch component set to offer newer domestic trucks and cars the ability to upgrade their vehicle's sound quality. This component set, with its innovative technology, makes it a simple solution to getting Alpine sound in many of these vehicles on the road today. INCREASED DRIVING POWER AND CONTROL The S-Series speakers have a large voice coil. The 6.5-inch and 6x9-inch models have a 35-mm voice coil, and this large voice coil size increases their driving power and control of the motor. The S-Series speakers are the first in the industry to use CFRP (Carbon Fiber Reinforced Plastic), a very lightweight yet rigid material. The edges are naturally weaker than the center on a standard, off-the-shelf oval cone due to the elongated shape. Since the CFRP material is directional, it can be manipulated during the molding process to strengthen the generally weak cone areas. The result is rigidity throughout the cone that delivers accurate and efficient performance. The ability to manipulate the CFRP material during molding is currently exclusive to Alpine and the S-Series speakers. Alpine has three patent-pending procedures in support of this innovative manufacturing process. General Features: 6" x 9" Type S Series 2-Way Coaxial Car Speakers Power Handling: Peak: 520 watts per pair / 260 watts each RMS: 170 watts per pair / 85 watts each Recommended Power Range: 10 - 85 watts RMS per channel Carbon Fiber Reinforced Plastic (CFRP) Cone High Amplitude Multi-Roll (HAMR) Surround 1" Silk Dome Tweeter Rubber magnet boot cover CEA-2031 compliant speakers 35mm Voice Coil Top-mount Depth: 2-15/16" Cutout Dimensions: 5-29/32" x 8-3/4" 4 ohms Impedance Frequency Response: 65 - 22000 Hz Sensitivity: 90dB Compatible with the Alpine KTE-S69G Grille Authorized Dealer 1-year Manufacturer's Warranty What is in the S2-S69 package: Two 2-way speakers 2 Bottom mount brackets Two 12" Lengths of speaker wire Eight 1-3/16" Screws Eight M4x60mm Machine screws Eight M4 Nuts 8 Speed clips 16 Flat washers 8 Split lock washers Warranty information Online product registration information Template and specs on the box S-S69 owner's manual Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

2 Pair Alpine S-S69 520W Max (170W RMS) 6" x 9" Type S Series 2-Way Coaxial Car Speakers + Metra 72-6512 Speaker Harness Connector for Chrysler Vehicles 90-07 Alpine S-S69 520W Max (170W RMS) 6" x 9" Type S Series 2-Way Coaxial Car Speakers FITS IN MOST COMMON APPLICATIONS To meet the needs of the most common applications in speaker replacement today, we've introduced a 6x9-inch component set to offer newer domestic trucks and cars the ability to upgrade the sound quality of their vehicle. With its innovative technology, this component set makes it a simple solution to getting Alpine sound in many of these vehicles on the road today. INCREASED DRIVING POWER AND CONTROL The S-Series speakers have a large voice coil. The 6.5-inch and 6x9-inch models have a 35-mm voice coil, and this large voice coil size increases their driving power and control of the motor. The S-Series speakers are the first in the industry to use CFRP (Carbon Fiber Reinforced Plastic), a very lightweight yet rigid material. The edges are naturally weaker than the center on a standard, off-the-shelf oval cone due to the elongated shape. Since the CFRP material is directional, it can be manipulated during the molding process to strengthen the areas of the cone that are generally weak. The result is rigidity throughout the cone that delivers accurate and efficient performance. The ability to manipulate the CFRP material during molding is currently exclusive to Alpine and the S-Series speakers. Alpine has three patent-pending procedures in support of this innovative manufacturing process. General Features: 6" x 9" Type S Series 2-Way Coaxial Car Speakers Power Handling: Peak: 520 watts per pair / 260 watts each Power Handling: RMS: 170 watts per pair / 85 watts each Recommended Power Range: 10 - 85 watts RMS per channel Carbon Fiber Reinforced Plastic (CFRP) Cone High Amplitude Multi-Roll (HAMR) Surround 1" Silk Dome Tweeter Rubber magnet boot cover CEA-2031 compliant speakers 35mm Voice Coil Top-mount Depth: 2-15/16" Cutout Dimensions: 5-29/32" x 8-3/4" 4 ohms Impedance Frequency Response: 65 - 22000 Hz Sensitivity: 90dB Compatible with the Alpine KTE-S69G Grille Authorized Dealer 1-year Manufacturer's Warranty What is in the S-S69 package: S-S69 owner's manual Two 2-way speakers 2 Bottom mount brackets Two 12" Lengths of speaker wire Eight 1-3/16" Screws Eight M4x60mm Machine screws  Eight M4 Nuts 8 Speed clips 16 Flat washers 8 Split lock washers 8 Spacers Warranty information Online product registration information Important Notice sheet Template and specs on the box (2) Pair of Metra 72-6512 Speaker Wire Adapters for Select Chrysler Vehicles Speaker Harness Connectors Adapters Designed For 1991-Up Chrysler Dodge Jeep Eagle Plymouth, Quick, and Easy Installation, Plug-In The Original Radio Receiver, No Cutting Into Original Wiring Required, High-Quality ABS Plastic Molded Connector For The Perfect Fit, Length: 7" Long. Compatibility List: Chrysler: 1999-2003 300M 1995-2000 Cirrus 1992-1999 Lebaron 1995-2002 LHS 1991-1996 New Yorker 1996-2003 Sebring Coupe 1995-2001 Sebring Sedan 1991-2002 Town & Country 2001-2003 Voyager Dodge: 1991-2003 Caravan 1994-1999 Dakota 1993 Daytona 1998-1999 Durango 1998-2007 Ram Pick Eagle: 1993-1997 Vision Jeep: 1997-2001 Cherokee 1997-2003 Wrangler Plymouth: 1996-2000 Breeze 1995-2001 Neon 1984-2000 Voyager ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

2 Alpine W10S4 10" Bass Subwoofer 750W Max (250W RMS) 10" BassLine Series Single 4 ohm Car Subwoofer Legendary Alpine quality at an affordable priceCar audio enthusiasts know that Alpine is the leader in technology and innovation. Their reputation for developing the most reliable products is legendary. The BassLine product line is their quest to give customers a quality product that won't break the bank.The surround and wattage match made in heaven.The 250 watts of continuous power that the W10S4 handles complements the poly-foam surround that Alpine went with. It provides the best sound quality money can buy at this price point.General Features: 10" Single 4-ohm BassLine (Bass) Series Subwoofer Power Handling: Peak: 750 watts RMS: 250 watts Recommended power range: 50W - 250W RMS Polypropylene-Mica cone High-excursion poly-foam surround Progressive Wavelet Ribs (P.W.R.) cone design An optional Alpine KTE-10PG subwoofer grill is available and is a wonderful complement to the trim ring with the Alpine logo High-strength custom steel frame 8AWG push terminals 2" voice coil 52oz. magnet Top-mount depth: 5-1/16" Cutout diameter: 9" Frequency Response: 24 - 200Hz Sensitivity: 86.6dB Resonance Frequency (Fs): 32 Authorized Dealer 1-year Manufacturer's Warranty What's in the  W10S4 package: W10S4 owner's manual One 10" Subwoofer per box Adhesive-backed foam gasket Application Guide Online product registration information Warranty Information Important Notice! ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

2 Alpine S-SB10V 10" Vented Loaded Halo Enclosure with Alpine KTA-30MW Weather-resistant Amplifier + Alpine KTX-H10 Alpine S-SB10V 10" Vented Loaded Halo Enclosure with Alpine KTA-30MW Weather-resistant Amplifier - This bundle includes an Alpine S-SB10V Pre-Loaded S-Series 10-inch Subwoofer Enclosure, an Alpine KTA-30MW Mono Tough Power Pack Amplifier 200 RMS x 1 at 4-Ohms / 300 RMS x 1 at 2-Ohms, a pry kit, and an Alpine cozy.Alpine S-SB10V Pre-Loaded S-Series 10-inch Subwoofer EnclosureAlpine Electronics of America, Inc. introduced a new sound system lineup for the Halo category that includes a 10-inch enclosure and remote bass knob. The enclosures are pre-loaded with S-Series and R-Series subwoofers.This sound system was designed to complement the Halo display in both power and performance for a premium sound experience. With the new modular design, customers can enjoy a single box design but have a flexible upgrade path. A single box can be used, or two enclosures can be linked together with an optional kit to create a dual sub enclosure.Enclosure Stacking FeaturesUnique to Alpine, the subwoofer 10-inch is available in a single or “linked” format with an optional mounting bracket. This innovative design allows the sound consumer the option to easily add more bass to their system.Optimized PerformanceThe ported enclosure design delivers a higher total sound output for deep, powerful bass, reliable sound reproduction, and overall great sound quality. The 10-inch enclosure is tuned to 36 Hz is tuned to 35 Hz for optimized performance with Alpine’s S-and-R-Series subwoofers.General Features: S-SB10V Pre-Loaded S-Series 10-inch Subwoofer Enclosure Includes S-W10D4 wired in parallel 600W RMS power handling 2Ω Impedance Ported enclosure design Frequency response: 28-200 Hz Vented enclosure tuning frequency: 36 Hz Dimensions 16-inch W x 12.6825-inch H x 14.5-inch D What is in the S-SB10V box: Ported enclosure loaded with one S-W10D4 subwoofer driver Rubber flange protector (installed on the subwoofer) Alpine KTA-30MW Car Amplifier Mono 300-Watt RMS Weather Resistant Tough Power Pack Amplifier A TOUGH MINI AMP THAT PACKS A PUNCH Get big amp performance in a compact, resilient package. With Alpine’s exclusive technology, Dynamic Peak Power (D.P.P.), the KTA-30MW Weather Resistant Tough Power Pack is sure to deliver powerful bass output for subwoofers used in those open cab vehicles and toys. This small and efficient amplifier can be installed with an aftermarket or factory head unit while adding up to 600 watts of D.P.P. power. Its weather resistance makes the KTA-30MW a good choice for use in exposed installations like side-by-sides, boats, open-top vehicles, and motorcycle saddlebags. A SOUND SYSTEM BOOST WITHOUT THE BIG SPACE COMMITMENT The KTA-30MW is perfect for when you want to add subwoofer power but don’t have space for a large amplifier. It is compatible with an aftermarket or factory head unit and provides up to 600 DPP watts to the subwoofer of your choice. HALF THE SIZE OF OUR SMALLEST TRADITIONAL AMPLIFIERS The KTA-30MW measures just 9-3/16” (W) x 1-5/8” (H) x 3-3/4” (D), so its small footprint lets it fit where most amplifiers won’t, like under the dash or in the glove compartment, installed under the dash of a side-by-side, placed in the saddlebag of a motorcycle, or used in other places where space is an issue. General Features: Alpine KTA-30MW Class D Monoblock Weather Resistant Power Pack Amplifier 300 Watts RMS X 1 @ 4 Ohms Power Handling 600 Watts RMS X 1 @ 2 Ohms Power Handling CTA-2006 compliant Frequency Response: 20-400 Hz Total Harmonic Distortion (THD): <1% Signal to Noise Ratio: 83dB Variable Low Pass filter 50-400Hz @ -24dB/Oct. Variable Bass Boost (0-12 dB at 50 Hz) Fuse Rating: 25A Weather-resistant (IP66 rating) Dynamic Peak Power (D.P.P.) technology intelligently adjusts the gain to automatically adapt to musical needs Dimensions: 7” W x 3.5” H x 1.25” D Authorized Dealer 1-year Manufacturer's Warranty What is in the KTA-30MW box: Mono amplifier 14" Power/signal harness (26-pin connector on one end and bare wires + RCAs on other ends) 4 Self-tapping screws (Length 3/4") Connection sheet Limited Warranty sheet KTA-30MW owner's manual Alpine KTX-H10 Linking Kit Heavy-duty steel front and rear linking brackets for connecting two Alpine Halo Linking Kit for Dual 10" Alpine Halo Preloaded Subwoofer Enclosures with ProLink, Heavy-duty steel front and rear linking brackets for connecting two Alpine Halo 10" subwoofer enclosures Add more bass to your sound system with the Linking Kit for Dual 10" Alpine Halo Preloaded Subwoofer Enclosures, featuring Alpine's new ProLink™ technology. General Features: Aluminum rear link plate 10-inch Front ABS / Steel reinforced the port link Center link stabilizing dowels Alpine logo plate All hardware included Authorized Internet Dealer What is in the KTX-H10 box: Front port-link Two 9" front port braces 23.25" Rear link-plate Four 25mm hex-socket screws Eight 14mm hex-socket screws Four 20mm threaded alignment posts 3mm Allen-key Installation instructions Safety warnings KTX-H10 Linking Kit owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

2 Alpine R2-W12D2 2250W Max (750W RMS) 12" R-Series Dual 2-Ohm Car Subwoofer The new 2022 R-Series subwoofers are here - drawing from decades of Subwoofer engineering experience. They deliver deep, clean, accurate bass and feature Alpine’s HAMR Surround for maximum cone excursion, delivering tons of bass output. The new ceramic dust cap is lightweight and rigid, keeping distortion at an absolute minimum. The enlarged motor structure ensures better woofer control for a strong, clean bass response. General Features: 12" Dual 2 ohm Type-R Subwoofer Peak Power Handling: 2250watts RMS Power Handling: 750 watts Recommended power range: 300 - 750W RMS CTA-2031 compliant power ratings Parabolic pulp/kevlar cone H.A.M.R. surround Polypropylene, mica, and talc dust cap Reinforced cone neck and spider joint Cast aluminum frame with integral shorting sleeve 8AWG push terminals with VC configuration jumpers 2.6" High excursion overhung voice coil 127 oz. Strontium ferrite segmented magnet Top-mount depth: 6-3/8" Cutout diameter: 10-7/8" Frequency Response: 24 - 200Hz Sensitivity: 84.3dB Resonance Frequency (Fs): 27Hz Authorized Dealer 1-year Manufacturer's Warranty What's in the R2-W12D2 package: R2-W12D2 owner's manual One 12" Dual 2-ohm voice coil subwoofer Two 3" jumper cables R-Series Subwoofer Application Guide Online product registration information Warranty Information https://www.youtube.com/watch?v=ihjWBSOYVxE&t=179s ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

2 Pair Pioneer TS-G6930F 6"x9" 800 Watts 3-Way Coaxial Car Speakers and Absolute SW16G50 50' 16 Gauge Speaker Wire TS-G6930F x 2SW16G50 Pioneer TS-G6930F 800W Max (90W RMS) 6" x 9" G-Series 3-Way Coaxial Car Speakers Our TS-G6930F speakers are excellent choices to replace a bad set of factory 6 x 9" speakers. Their two-way design handles 400 watts max. power (45 watts nominal) and features Pioneer’s extremely strong and lightweight Injected Molded Polypropylene™ (IMPP) Composite Cone Woofer for improved sensitivity and reduced distortion. You don't get just basic, run-of-the-mill features either. The conex damper delivers higher power handling and deeper bass, and the 2" Cone midrange and 3/8" Dome tweeter reproduces highs with great performance and musicality. These speakers are designed with a shallow mounting depth for easy install into a wide variety of vehicles. Speaker grilles are not included. General Features: Pioneer TS-G6930F 6" x 9" G-Series 3-Way Car Speakers Power Handling: Peak: 800 watts per pair / 400 watts each RMS: 90 watts per pair / 45 watts each Injection-molded polypropylene cone Rubber-coated cloth surround 2" Cone Tweeter 3/8" Dome Supertweeter Ferrite magnet motor structure Top-mount Depth: 2-3/4" Cutout Dimensions: 6" x 8-3/4"" 4 ohms impedance Frequency Response: 32 - 32,000 Hz Sensitivity: 90dB ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

2 Pair Alpine S2-S65 6.5" 480 Watt Car Audio Speakers+BBX-F1200 4 Channel Amplifier + Absolute KIT4 4G Amp Kit Alpine S2-S65 120W 6.5" 2-Way Type-E Coaxial Car Speakers w/ Silk Tweeters Hearing is BelievingStep up your factory speakers to an affordable upgrade with the all-new Alpine Type-E speakers for the performance-packed sound quality you expect from Alpine.Quality over QuantityJust because you want better sound in your car doesn’t mean you have to break your budget. The Type-E speakers are the perfect, affordable option if you need replacement speakers or want to start building a sound system.Soft Dome Tweeter TechnologyTo output quality sound, the Type-E speakers are developed using soft dome tweeters rather than traditional cone-type tweeters, which can be harsh. This results in a more enjoyable listening experience in the car when playing back music or other entertainment over your sound system.General Features: 6-1/2" S Series 2-way Coaxial Car Speakers Peak Power Handling: 480 watts per pair / 240 watts each RMS Power Handling: 160 watts per pair / 80 watts each Hi-Res Audio-certified Polypropylene, Glass Fiber, and Mica cone material High-Amplitude Multi-Roll (HAMR) speaker surround 1" Cloth Dome tweeters voice coil Ferrite magnet motor structure Top-mount Depth: 2-5/16" Cutout Dimensions: 5-1/8" Impedance: 4 ohms Frequency Response: 70 - 40,000 Hz Sensitivity: 88 dB Speaker grilles are optional and sold separately Authorized Internet Dealer 1-year Manufacturer's Warranty What's in the box: Alpine S2-S65 owner's manual Two 2-way speakers 2 Adapter rings Two 12" Lengths of speaker wire Eight 1-1/8" Screws Eight M4x6.5mm Machine screws with split lock washers attached Eight M4 Nuts 6 Flat washers Warranty information Online product registration information Alpine BBX-F1200 600W Max (280W RMS) 2-ohm Stable 4 Channel Class-A/B Amplifier This new BBX amplifier gives you Alpine power performance at a fantastic price. And they’re designed to fit easily in virtually any system. High Power, Great Value This amp delivers high output power and exceptional performance for their class. A great way to expand your sound system on a limited budget. High Pass and Low Pass Filters These two filters let you set the frequency points for the high, mid, and bass ranges to match your speakers and ensure optimum efficiency. Performance With Bass EQ, you can maximize the performance of your system and get even more powerful bass. General Features: Alpine BBX-F1200 Class-A/B 2-ohm Stable 4-Channel Amplifier RMS Power Rating: 4 ohms: 50 watts x 4 channel 2 ohms: 70 watts x 4 channel 1 ohm: ------------N/A------------ Bridged, 4 ohms: 130 watts x 2 channel Total power output: 600 watts Pulse Width Modulated MOSFET power supply LED power (green) and protect (red) indicators Soft start turn-on 4/3/2 or channel operation 3-way protection circuitry (thermal, overload, and speaker short protection) Dual speaker terminals simplify the hookup of multiple speakers Heavy-duty aluminum alloy heat-sink Input sensitivity: .2V - 8V Frequency Response: 5 - 50000 Hz Total Harmonic Distortion (THD): <1% Signal to Noise Ratio: 95dB Variable high-pass filter: 50 - 500 Hz Variable low-pass filter: 50 - 500 Hz Variable Bass Boost: 0 to +12 dB bass boost Fuse Rating: 40A x 1 Dimensions: 9.4"W x 12.9"L x 2"H Authorized Dealer 1-year Manufacturer's Warranty. Absolute KIT4 Complete PRO Marine 4 Gauge 2000 Watts Amplifier Complete Installation Amp Kit Power Wiring with Red Accent Color Scheme Installing a car amplifier is already enough of a job without worrying about where to find the correct wire and installation accessories. You might not know that some companies are playing gimmicks, and you could get ripped off! Today, I recommend KIT4 for all DIY and installers. This wiring kit has an easy-to-install AGU fuse holder and some perfect wiring. The positive and negative power wires are made with copper-coated aluminum (CCA) wiring to keep costs down but remain highly flexible and installer-friendly. The speaker wire kicks ass, and I was not expecting such a high-quality roll of speaker wire to be included. It feels great, works great, and is much better than the typical 18 AWG wire most kits would consist of. General Features: Complete 4 Gauge Amplifier Kit Designed specifically for car audio systems up to 1000 watts Premium power and ground wire provide optimal power transfer Includes 2-channel RCA interconnect cables for the audio signal connection from the receiver to the amplifier Terminals are gold-plated for excellent signal transfer For use in any car, truck, RV, or boat Authorized Internet Dealer 1-year Manufacturer's warranty Package Includes: 17 ft. of red 4 AWG high current power cable Three ft. of black 4 AWG ground cable 15 ft. of RCA triple shielded interconnect audio cable with built-in remote wire 20 ft. of 12 AWG OFC Speaker cable 20 ft. of 16 AWG remote turn-on wire Six ft. of split loom tubing 1 Gold-plated 80 AMP AGU fuse 1 4 AWG gold ring terminal 1 4 AWG water-resistant inline fuse holder 2 Ring terminals 2 Spade terminals (4 gauge) 5 Spade terminals (14-16 gauge) 3 Self-tapping screws 1 Rubber grommet 20 Black cable ties 2 Butt connectors (18-22 gauge) 1 Butt connector (4 gauge) Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

2 Pair Alpine S2-S65 6.5" 480 Watt Car Audio Speakers+BBX-F1200 4 Channel Amplifier + Absolute KIT4 4G Amp Kit Alpine S2-S65 120W 6.5" 2-Way Type-E Coaxial Car Speakers w/ Silk Tweeters Hearing is BelievingStep up your factory speakers to an affordable upgrade with the all-new Alpine Type-E speakers for the performance-packed sound quality you expect from Alpine.Quality over QuantityJust because you want better sound in your car doesn’t mean you have to break your budget. The Type-E speakers are the perfect, affordable option if you need replacement speakers or want to start building a sound system.Soft Dome Tweeter TechnologyTo output quality sound, the Type-E speakers are developed using soft dome tweeters rather than traditional cone-type tweeters, which can be harsh. This results in a more enjoyable listening experience in the car when playing back music or other entertainment over your sound system.General Features: 6-1/2" S Series 2-way Coaxial Car Speakers Peak Power Handling: 480 watts per pair / 240 watts each RMS Power Handling: 160 watts per pair / 80 watts each Hi-Res Audio-certified Polypropylene, Glass Fiber, and Mica cone material High-Amplitude Multi-Roll (HAMR) speaker surround 1" Cloth Dome tweeters voice coil Ferrite magnet motor structure Top-mount Depth: 2-5/16" Cutout Dimensions: 5-1/8" Impedance: 4 ohms Frequency Response: 70 - 40,000 Hz Sensitivity: 88 dB Speaker grilles are optional and sold separately Authorized Internet Dealer 1-year Manufacturer's Warranty What's in the box: Alpine S2-S65 owner's manual Two 2-way speakers 2 Adapter rings Two 12" Lengths of speaker wire Eight 1-1/8" Screws Eight M4x6.5mm Machine screws with split lock washers attached Eight M4 Nuts 6 Flat washers Warranty information Online product registration information Alpine BBX-F1200 600W Max (280W RMS) 2-ohm Stable 4 Channel Class-A/B Amplifier This new BBX amplifier gives you Alpine power performance at a fantastic price. And they’re designed to fit easily in virtually any system. High Power, Great Value This amp delivers high output power and exceptional performance for their class. A great way to expand your sound system on a limited budget. High Pass and Low Pass Filters These two filters let you set the frequency points for the high, mid, and bass ranges to match your speakers and ensure optimum efficiency. Performance With Bass EQ, you can maximize the performance of your system and get even more powerful bass. General Features: Alpine BBX-F1200 Class-A/B 2-ohm Stable 4-Channel Amplifier RMS Power Rating: 4 ohms: 50 watts x 4 channel 2 ohms: 70 watts x 4 channel 1 ohm: ------------N/A------------ Bridged, 4 ohms: 130 watts x 2 channel Total power output: 600 watts Pulse Width Modulated MOSFET power supply LED power (green) and protect (red) indicators Soft start turn-on 4/3/2 or channel operation 3-way protection circuitry (thermal, overload, and speaker short protection) Dual speaker terminals simplify the hookup of multiple speakers Heavy-duty aluminum alloy heat-sink Input sensitivity: .2V - 8V Frequency Response: 5 - 50000 Hz Total Harmonic Distortion (THD): <1% Signal to Noise Ratio: 95dB Variable high-pass filter: 50 - 500 Hz Variable low-pass filter: 50 - 500 Hz Variable Bass Boost: 0 to +12 dB bass boost Fuse Rating: 40A x 1 Dimensions: 9.4"W x 12.9"L x 2"H Authorized Dealer 1-year Manufacturer's Warranty. Absolute KIT4 Complete PRO Marine 4 Gauge 2000 Watts Amplifier Complete Installation Amp Kit Power Wiring with Red Accent Color Scheme Installing a car amplifier is already enough of a job without worrying about where to find the correct wire and installation accessories. You might not know that some companies are playing gimmicks, and you could get ripped off! Today, I recommend KIT4 for all DIY and installers. This wiring kit has an easy-to-install AGU fuse holder and some perfect wiring. The positive and negative power wires are made with copper-coated aluminum (CCA) wiring to keep costs down but remain highly flexible and installer-friendly. The speaker wire kicks ass, and I was not expecting such a high-quality roll of speaker wire to be included. It feels great, works great, and is much better than the typical 18 AWG wire most kits would consist of. General Features: Complete 4 Gauge Amplifier Kit Designed specifically for car audio systems up to 1000 watts Premium power and ground wire provide optimal power transfer Includes 2-channel RCA interconnect cables for the audio signal connection from the receiver to the amplifier Terminals are gold-plated for excellent signal transfer For use in any car, truck, RV, or boat Authorized Internet Dealer 1-year Manufacturer's warranty Package Includes: 17 ft. of red 4 AWG high current power cable Three ft. of black 4 AWG ground cable 15 ft. of RCA triple shielded interconnect audio cable with built-in remote wire 20 ft. of 12 AWG OFC Speaker cable 20 ft. of 16 AWG remote turn-on wire Six ft. of split loom tubing 1 Gold-plated 80 AMP AGU fuse 1 4 AWG gold ring terminal 1 4 AWG water-resistant inline fuse holder 2 Ring terminals 2 Spade terminals (4 gauge) 5 Spade terminals (14-16 gauge) 3 Self-tapping screws 1 Rubber grommet 20 Black cable ties 2 Butt connectors (18-22 gauge) 1 Butt connector (4 gauge) Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.