Class-D Amplifiers (339)

Diamond Audio DES500.1D DES 1-Channel Full Range Class D Amplifier Diamond Elite DES series amplifiers have been our workhorse since their introduction last year when it was engineered and designed from the ground up. Smaller than the previous generation and constructed with the same footprint dimensions for all models, these amplifiers have been engineered to sound even more dynamic and to deliver optimal rated power at all impedance levels! An ll Diamond Elite DES series amplifiers feature various switched speaker level turn-on options (VOX/DC Offset/REM), utilize the latest digital chipset technology, and provide installation flexibility and all the controls necessary to fine-tune and improve the sound quality of any car audio system. General Features Latest High-Efficiency Full-Range Digital Topology Surface Mount Component Technology with 4-Layer PCB Common Compact Size with Single-Sided Connections and Top Mount Controls Handles HI and LO level input up to 12V Switched Speaker Level Turn On Options (VOX/DC Offset/REM) Remote Bass Level Control Included Fully Variable 35Hz - 350Hz 12dB per Octave Crossovers 0 -180 Degrees of Phase adjustment Bass Boost EQ Up To 12dB ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

 Diamond Audio DES400.4D 4-Channel Full Range Class D Amplifier General Features Diamond Elite Series Class D 2 ohm Stable 4-Channel Amplifier 4 Ohms RMS Power Rating: 140 watts x 4 channel 2 Ohms RMS Power Rating: 170 watts x 4 channel Bridged Power Rating: 400 watts x 2 channel @ 4 ohm Total power output: 800 watts LED Power/Protect Light Surface mount component technology with 4-layer PCB Compact size with single-sided connections Speaker-level (high-level) inputs via direct connection of speaker wire to the low-level inputs Switched speaker level turn on options (Vox/DC Offset/Rem) Input sensitivity Frequency Response: 10 - 35000 Hz Total Harmonic Distortion (THD): 0.07% Signal to Noise Ratio: -77.4 dB Variable low-pass filter: 35 - 350 Hz Fuse Rating: 60A 8 AWG gauge amplifier wiring kit is recommended for installation Dimensions: 9.3" L x 5.27" W x 1.75" H Authorized Internet Dealer 1-year Manufacturer's Warranty Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Diamond Audio DES400.2D 2-Channel Full Range Class D Diamond Elite DES series amplifiers have been our workhorses since their introduction last year, when they were engineered and designed from the ground up. Smaller than the previous generation and constructed with the exact footprint dimensions for all models, these amplifiers have been engineered to sound even more dynamic and to deliver optimal rated power at all impedance levels! All Diamond Elite DES series amplifiers feature various switched speaker-level turn-on options (VOX/DC Offset/REM), utilize the latest digital chipset technology, and provide installation flexibility along with all the controls necessary to fine-tune and improve the sound quality of any car audio system. General Features: 120 W x 4 @ 4Ω 185 W x 4 @ 2Ω 370 W x 2 @ 4Ω bridged S/N: ≤ 95 dBA / THD: .06% Dimensions: (Remote Included): 8.75" x 7.67" x 2" (222 x 195 x 51.5 mm) Anodized Extruded Aluminum Heat Sink Provides Superior Thermal Performance 4-Layer PCB Board with Balanced Differential Inputs Full Range Class D IR Chipset "SNAP" Capacitors used throughout the Circuit Audiophile Grade High Tolerance Components Spring Steel FET Clips Provide a Cleaner Board Design Illuminated Logo / Fully Concealed Mounting Output Clip Indicators for Precise Set-Up Fine-Tuned Fully Variable Crossovers and Phase Control Top Mounted Controls for Convenient Amplifier Adjustment Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

  Diamond Audio HX600.4 HEX Series 4-Channel Class-D Car Audio Amplifier This amplifier is manufactured by Diamond Audio to operate at a total power of 600 Watts Max and is crafted with the best components on the market. It has a high-density aluminum alloy heat sink with a backlit logo bringing you style and longevity in a compact system. A BTR port allows you to control it via Bluetooth and integrated soft clip light for quick system set-up. General Features: An anodized extruded aluminum heat sink provides superior thermal stability. Four-layer, glass epoxy circuit board for enhanced performance and reliability Audiophile-grade high-tolerance components are used throughout Full Range Class D amplifier technology Bridgeable for high power operation (CH1+CH2+CH3+CH4) Balanced differential inputs for superior noise rejection Input selector switch (2 channel / 4 channel) Output clip indicators for precise system set-up Fully variable, 24dB per octave, electronic crossovers Adjustable Bass EQ (45Hz: 0dB to +12dB) Full range, line level outputs provided to send a signal to another amplifier Top-mounted controls for convenient adjustment Illuminated logo / fully concealed mounting Specifications: RMS Power Rating RMS Power (4Ω): 160 W X 4 RMS Power (2Ω): 250 W X 4 Bridged(mono 4Ω): 500 W X 2 Bridged(mono 2Ω): N/A Bridged(stereo 4Ω): 500 W X 2 Type Topology: Full Range Class D Power Supply Power Supply: Full PWM Power Supply Threshold: 10.0VDC-170VDC Idle Current: (0.7A) Distortion THD 4(1KH@4Ω) : 0.06% S/N Ratio(A weighted@1W): -80dBA S/N Ratio(A weighted@FP): .95dBA Input Sensitivity Low Input Level: 200mV-5.0V High Input Level: N/A Input Impedance Low Input Level: 20 KΩ High Input Level: N/A Output Stage Output Impedance: 0.011 Ω Damping Factor(50Hz@4Ω): >250 Bandwidth(-3dB): 10Hz-35KHz Crossover(-12dB/Oct) Variable High-Pass: 40Hz-400Hz Variable Low-Pass: 40Hz-400Hz Variable Sub-Sonic: N/A Fuse Ratings ATC: 25A X 2 Dimensions Length x Width x Height(Inches): 11.9" x 7.67" x 2" Length x Width x Height(mm): 302 x 195 x 51.5 ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

 Diamond Audio HX480.4 4-Channel 480W RMS Full Range Class D AmplifierAudiophile-grade high tolerance components - 4-layer PCB board with balanced differential inputs - full-range digital class-d Ir chip sets - fine-tuned variable - crossover and phase control- top mounted controls for convenient amplifier adjustment turn to hex series amplifiers for superior sound quality and unparalleled power for the ultimate audiophile system set up. Composed of high-tolerance grade components and tuning adjustments to fit your listening desires, hex series amplifiers are the choice for those who expect the best! General Features: 120 W x 4 @ 4Ω 185 W x 4 @ 2Ω 370 W x 2 @ 4Ω bridged S/N: ≤ 95 dBA / THD: .06% Dimensions: (Remote Included): 8.75" x 7.67" x 2" (222 x 195 x 51.5 mm) Anodized Extruded Aluminum Heat Sink Provides Superior Thermal Performance 4-Layer PCB Board with Balanced Differential Inputs Full Range Class D IR Chipset "SNAP" Capacitors used Throughout the Circuit Audiophile Grade High Tolerance Components Spring Steel FET Clips Provide a Cleaner Board Design Illuminated Logo / Fully Concealed Mounting Output Clip Indicators for Precise Set-Up Fine Tuned Fully Variable Crossovers and Phase Control Top Mounted Controls for Convenient Amplifier Adjustment ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Diamond Audio HX1200.1D HEX Series Monoblock Class-D Car Audio Amplifier + Absolute KIT0 0 Gauge Amplifier It is introducing the all-new range of Diamond Audio HEX series amplifiers, made for ultimate sound quality and performance. It features a four-layer glass epoxy circuit board, top-mounted controls, and a brushed copper look exterior, making it great for a show car. General Features: Anodized Extruded Aluminum Heat Sink provides superior thermal performance 4-Layer PCB Board with balanced differential inputs Full Range Class D IR Chipset "Snap" capacitors are used throughout the circuit Audiophile Grade High Tolerance Components Spring Steel FET Clips provide a cleaner board design Illuminated logo / fully concealed mounting Output clip indicators for precise setup Fine-tuned fully variable crossovers and phase control Top-mounted controls for convenient amplifier adjustment Monoblock Class-D Amplifier RMS Power Rating: 4 Ohm: 540 watts x 1 Channel RMS Power Rating: 2 Ohm: 870 watts x 1 Channel RMS Power Rating: 1 Ohm: 1200 watts x 1 Channel Frequency Response: 10Hz - 300Hz Variable Low-Pass Filter (12dB/Octave): 30Hz - 300Hz Variable Sub-Sonic Filter (12dB/Octave): 10Hz - 55Hz Top Mounted Controls Anodized Extruded Aluminum Heat Sink 4-Layer PCB Board Balanced Differential Inputs Illuminated Logo Dimensions: 14.2" (362mm) x 7.67" (195mm) x 2" (51.5mm) 1-Year Warranty What is Included? One (1) Diamond Audio HX1200.1D HEX Series Monoblock Class-D Car Audio Amplifier ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Diamond Audio HX800.1D HEX Mono 800W RMS Class D Subwoofer Amplifier. Audiophile-grade high tolerance components - 4-layer PCB board with balanced differential inputs - full-range digital class-d Ir chip sets - fine-tuned variable - crossover and phase control- top mounted controls for convenient amplifier adjustment turn to hex series amplifiers for superior sound quality and unparalleled power for the ultimate audiophile system set up. Composed of high-tolerance grade components and tuning adjustments to fit your listening desires, hex series amplifiers are the choice for those who expect the best! General Features RMS Power Rating: 340 W x 1 @ 4Ω RMS Power Rating: 560 W x 1 @ 2Ω RMS Power Rating: 800 W x 1 @ 1Ω S/N: ≤ 95 dBA / THD: .06% Dimensions: (Remote Included): 9.92" x 7.67" x 2" (252 x 195 x 51.5 mm) Anodized Extruded Aluminum Heat Sink Provides Superior Thermal Performance 4-Layer PCB Board with Balanced Differential Inputs Full Range Class D IR Chipset "SNAP" Capacitors used Throughout the Circuit Audiophile Grade High Tolerance Components Spring Steel FET Clips Provide a Cleaner Board Design Illuminated Logo / Fully Concealed Mounting Output Clip Indicators for Precise Set-Up Fine Tuned Fully Variable Crossovers and Phase Control Top Mounted Controls for Convenient Amplifier Adjustment ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

 Diamond Audio HX400.2 2-Channel 400W RMS Full Range Class D Amplifier Audiophile-grade high tolerance components - 4-layer PCB board with balanced differential inputs - full-range digital class-d Ir chip sets - fine-tuned variable - crossover and phase control- top mounted controls for convenient amplifier adjustment turn to hex series amplifiers for superior sound quality and unparalleled power for the ultimate audiophile system set up. Composed of high-tolerance grade components and tuning adjustments to fit your listening desires, hex series amplifiers are the choice for those who expect the best! General Features: Amplifier 2 Channel RMS Power(2Ω) 350 W X 2 RMS Power (4Ω) 200 W X 2 RMS Bridge (mono 2Ω) N/A RMS Bridge (mono 4Ω) 700 W X 1 RMS Bridge (stereo 4Ω) N/A Topology Full-Range Class D Power Supply Full PWM Power Supply (Threshold) 10.0VDC – 17.0VDC Idle Current (0.7A) Distortion - THD (1KHz@4Ω) 0.06% Distortion - S/N Ratio (A weight @ 1W) -80dBA Distortion - S/N Ratio (A weight @ FP) -95dBA Input Sensitivity Low 200mV – 5.0V Input Sensitivity High N/A Input Impedance - Low Input Level 20 KΩ Input Impedance - High Input Level N/A Output Impedance 0.011Ω Damping Factor (50Hz@4Ω) >250 Bandwidth (-3dB) 10Hz-35kHz Crossover (-12 dB/ Oct) Variable High-Pass 40Hz - 400Hz Crossover (-12 dB/ Oct) Variable Low-Pass 40Hz - 400Hz Crossover (-12 dB/ Oct) Variable Sub-Sonic N/A FUSE Ratings - ATC 25A X 2 Dimension - Length x Width x Height - Inches(mm) 8.75″ x7.67″ x 2″ (222 x 195 x 51.5 mm) ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate R2-300X4 Prime Series 300 Watts 4-Channel Class D Amplifier Primed for performance, the R2-300X4 is a 300-watt, full-range Class-D amplifier capable of operating at 4Ω or 2Ω stereo and 4Ω bridged/mono. This amplifier is extremely efficient because of its Class-D technology, which reduces the vehicle's electrical system demand. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. supply that generates more power as voltage increases. General Features: Rockford Fosgate Prime R2-300X4 Class-D Full-Range 4-Channel Amplifier 50 watts RMS x 4 at 4 ohms 75 watts RMS x 4 at 2 ohms 150 watts RMS x 2 bridged output at 4 ohms bridged mode Total power output: 3000 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeat able Auto Turn-On Circuit Features C.L.E.A.N. Set-up 2/4 Channel Input Selection Switch Front and Rear Variable Input Gain adjustment level Continuously Variable on-Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Full Range Class D Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers 1 Year Warranty Low level: 125mV-5V High level: 250mV-10V Frequency Response: 20 Hz - 20 kHz Hz Total Harmonic Distortion (THD): <1% Variable high-pass filter: 50 - 250 Hz, 24 dB/octave Variable low-pass filter: 50 - 250 Hz, 24 dB/octave Recommended Fuse Rating: 60A Dimensions: 1.9" x "6.8" x "10.1" Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the R2-300X4 package: R2-300X4 Owner's Manual 4-Channel amplifier Two 7" Speaker input harnesses 3mm Allen Hex key Four 3/4" Screws 4 Flat washers Installation and Operation Instructions Certificate of Performance Rockford Fosgate contact information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.