Alpine (870)

2 Alpine SWT-10S2 10" 1000W Peak/350W RMS Shallow Slim Truck Car Subwoofer Bundle with AudioControl The Epicenter Black Digital Car Bass Processor with Remote Audio Control Alpine SWT-10S2 1000W Peak 10" SWT Series Single 2-ohm Shallow Mount Subwoofer Right size, Right sound. Here's a big bass breakthrough for truck lovers. Alpine engineered their SWT-10S2 10" subwoofer to go behind your seat and sound especially good in the limited space of a truck cab. This deep-sounding, high-performance sub works well in shallow enclosures that'll fit behind or under the seat in your truck. A "high amplitude" surround allows more cone travel than a regular sub, so the SWT-10S2 can push more air and play louder. Airflow-insured subs get hot as they play, and the heat usually gets vented away via a port in the back of the sub's pole piece. Alpine recessed the pole port and added cooling air vents on the sides of the frame, allowing you to use an enclosure with an inside clearance of as little as 4-3/16" without blocking critical airflow. An SWT-10S4 will work well in a ported or sealed box to get your favorite bass tone, boomy or tight. The power takes for top performance, and you'll want to pick an amplifier that delivers between 300 and 500 watts RMS at 4 ohms. This single voice coil, the 4-ohm sub, will draw the maximum output power from a subwoofer amplifier when used along with a second SWT-10S2 in a system. If you plan on running a pair, look for an amp that delivers between 600 and 1000 watts RMS at 2 ohms. General Features: 10" SWT Series Single 2-ohm Shallow Mount Truck Subwoofer Peak Power Handling: 1,000 watts RMS Power Handling: 350 watts Recommended Power Range: 100W - 350W Poly-Mica Dust Cap & Pulp-Kevlar Polyurethane Foam Surround H.A.M.R. Surround Technology Spiral Cut Aluminum Former 65mm Voice Coil with High-Temp 4-Layer SVC Winding 8AWG Push Terminals Top-mount depth: 4-3/16" Mounting Diameter: 8-15/16'' Frequency Response: 30 - 200 Hz Sensitivity: 84.8 dB Authorized Dealer 1-year Manufacturer's Warranty What's in the SWT-10S2 package: SWT-10S2 owner's manual 10" Thin-mount subwoofer Online product registration information Warranty information Audio Control THE EPICENTER 2-Channel Concert Series Digital Bass Restoration Processor with Bass Remote Your MP3 player thinks your car stereo is a pair of headphones, so it removes the bass! The Epicenter restores the earth-shaking power and heart-pounding bass your subwoofers crave. Give your subwoofers the juice to go lower and hit harder.  The Epicenter uses a bass circuit to drive your subwoofers lower, grabbing the attention of every eye on the boulevard. General Features: Active Epicenter Series 2 channel digital bass restoration and line output converter Designed to integrate with after-market or factory OEM systems Digital bass restoration restores bass roll-off in factory systems Speaker level inputs Bass/Gain level remote: Yes Signal-Sensing turn-on: Yes Preamp outputs: 1 pair Bass Maximizer circuitry Multiple turn-on options PFM Subsonic Filter bypass option Selectable impedance load: 20, 60, 20k ohms Frequency response: 10 - 100,000 Hz Subsonic filter: 20 Hz, 12/dB octave Signal-to-noise ratio: >130 dB Total harmonic distortion (THD): 0.003% Fuse Rating: 1A x 1  Dimensions: 8-1/16"W x 1-1/4"H x 6-3/4"H Weight: 1.70lbs Authorized Internet Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) What is in the THE EPICENTER package: The Epicenter owner's manual Pre-amp Bass Restoration Processor black Remote dash mount control Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine S-SB10V 10" 600W S-W10D4 Subwoofer Ported Sub Enclosure Box Alpine Amp Package Includes: (1) Alpine S-SB10V Loaded 10" 600w S-W10D4 Subwoofer Ported Sub Enclosure Box (1) Alpine S-A60M 600-Watt RMS Mono Car Audio Amplifier Subwoofer Amp Class-D (1) Absolute KIT4 4 Gauge Complete Car Amp Wiring Installation Wire Kit with RCA's Alpine S-SB10V Loaded 10" 600w S-W10D4 Subwoofer Ported Sub Enclosure Box Alpine Electronics of America, Inc. introduced a new sound system lineup for the Halo category that includes a 10-inch enclosure and remote bass knob. The enclosures are pre-loaded with S-Series and R-Series subwoofers. This sound system was designed to complement the Halo display in both power and performance for a premium sound experience. With the new modular design, customers can enjoy a single box design but have a flexible upgrade path. A single box can be used, or two enclosures can be linked together with an optional kit to create a dual sub enclosure. Enclosure Stacking Features Unique to Alpine, the subwoofer 10-inch is available in a single or “linked” format with an optional mounting bracket. This innovative design allows the sound consumer the option to easily add more bass to their system. Optimized Performance The ported enclosure design delivers a higher total sound output for deep, powerful bass, reliable sound reproduction, and overall great sound quality. The 10-inch enclosure is tuned to 36 Hz is tuned to 35 Hz for optimized performance with Alpine’s S-and-R-Series subwoofers. General Features: S-SB10V Pre-Loaded S-Series 10-inch Subwoofer Enclosure Includes S-W10D4 wired in parallel 600W RMS power handling 2Ω Impedance Ported enclosure design Frequency response: 28-200 Hz Vented enclosure tuning frequency: 36 Hz Dimensions 16-inch W x 12.6825-inch H x 14.5-inch D Alpine S-A60M 600-Watt RMS Mono Car Audio Amplifier Subwoofer Amp Class-D S-Series amplifiers are your sound system’s workhorse. With unmatched reliability and budget-friendly prices, these amplifiers are the better choice in performance value. THE BETTER CHOICE IN PERFORMANCE VALUE Perfect for beginners and enthusiasts alike, the S-Series amplifiers have the technology to improve your music experience yet are still friendly on your wallet. Used in conjunction with our advanced S-Series speakers and subwoofers, they create a complete sound system that takes your in-vehicle music experience to the next level. SMALL BUT MIGHTY The S-Series amplifiers are designed to fit anywhere. Measuring at 8”, these amplifiers can be mounted under seats or behind panels. Though they sport a compact footprint on the outside, they produce impressive power on the inside. At 600 watts RMS, the S-A60M is a powerful partner to drive the versatile S-Series subwoofers. RELIABLE PERFORMANCE The S-Series amplifiers contain technology that was previously only available in our premium line up of amplifiers, the R- and X-Series models. The S-Series models are based on Alpine’s intelligent amplifier platform that ensures superior sound reproduction and precision imaging. With an improved heat sink, and protection circuit design that eliminates thermal shut-down, your music will keep playing no matter where your drive takes you. General Features: Alpine’s Class D Amplifier Circuit CTA-2006-B Power Rating: 330W RMS x 1 (4ohm, 14.4V ≤ 1% THD+N); 600W RMS x 1 (2ohm, 14.4V ≤ 1% THD+N) S/N ratio: >85dB (ref: 1W into 4 ohm), >105dB (ref: rated power into 4 ohm) THD+N ≤ 0.03% (ref 1W info 4 ohm) Frequency Response: 10Hz-400Hz (+/-3 dB) Damping Factor: > 1000 Remote bass knob compatible (requires RUX-KNOB.2, sold separately) Absolute KIT4 4 Gauge Complete Car Amp Wiring Installation Wire Kit with RCA's General Features: Complete 4 Gauge Amplifier Kit Designed specifically for car audio systems up to 1000 watts Premium power and ground wire provides optimal power transfer Includes 2-channel RCA interconnect cables for the audio signal connection from the receiver to the amplifier Terminals are gold-plated for excellent signal transfer For use in any car, truck, RV, or boat Authorized Internet Dealer 1-year Manufacturer's warranty Package Includes: 17 ft. of red 4 AWG high current power cable 3 ft. of black 4 AWG ground cable 15 ft. of RCA triple shielded interconnect audio cable with built in remote wire 20 ft. of 12 AWG OFC Speaker cable 20 ft. of 16 AWG remote turn-on wire 6 ft. of split loom tubing 1 Gold plated 80 AMP AGU fuse 1 4 AWG gold ring terminal 1 4 AWG water resistant inline fuse holder 2 Ring terminals 2 Spade terminals (4 gauge) 5 Spade terminals (14-16 gauge) 3 Self tapping screws 1 Rubber grommet 20 Black cable ties 2 Butt connectors (18-22 gauge) 1 Butt connector (4 gauge) ⚠️Warning: Cancer and Reproductive Harm-www.P65Warnings.ca.gov    

Alpine S-S69 520W Max (170W RMS) 6" x 9" Type S Series 2-Way Coaxial Car Speakers with METRA 72-5600 Speaker Wire Harness & METRA 82-3004 6x9" Speaker Adapter FITS IN MOST COMMON APPLICATIONS To meet the needs of the most common applications in speaker replacement today, we've introduced a new 6x9-inch component set to offer newer domestic trucks and cars the ability to upgrade the sound quality in their vehicle. This component set with its innovative technology makes it a simple solution to getting Alpine sound in many of these vehicles on the road today INCREASED DRIVING POWER AND CONTROL The S-Series speakers have a large voice coil. The 6.5-inch and 6x9-inch models have a 35-mm voice coil, and this large voice coil size increases their driving power and control of the motor. The S-Series speakers are the first in the industry to use a material called CFRP (Carbon Fiber Reinforced Plastic), a very lightweight yet rigid material. On a standard, off-the-shelf oval cone, the edges are naturally weaker than the center due to the elongated shape. Since the CFRP material is directional, it can be manipulated during the molding process to strengthen the areas of the cone that are generally weak. The result is rigidity throughout the cone that delivers accurate and efficient performance. The ability to manipulate the CFRP material during the molding process is currently exclusive to Alpine and the S-Series speakers. Alpine has three patent-pending procedures in support of this innovative manufacturing process. General Features: 6" x 9" Type S Series 2-Way Coaxial Car Speakers Power Handling: Peak: 520 watts per pair / 260 watts each RMS: 170 watts per pair / 85 watts each Recommended Power Range: 10 - 85 watts RMS per channel Carbon Fiber Reinforced Plastic (CFRP) Cone High Amplitude Multi-Roll (HAMR) Surround 1" Silk Dome Tweeter Rubber magnet boot cover CEA-2031 compliant speakers 35mm Voice Coil Top-mount Depth: 2-15/16" Cutout Dimensions: 5-29/32" x 8-3/4" 4 ohms Impedance Frequency Response: 65 - 22000 Hz Sensitivity: 90dB Compatible with the Alpine KTE-S69G Grille Authorized Dealer 1-year Manufacturer's Warranty What is in the S-S69 package: Two 2-way speakers 2 Bottom mount brackets Two 12" Lengths of speaker wire Eight 1-3/16" Screws Eight M4x60mm Machine screws Eight M4 Nuts 8 Speed clips 16 Flat washers 8 Split lock washers Warranty information Online product registration information Template and specs on the box S-S69 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine R-S65C.2 100W RMS 6.5" R-Series Component 2-Way Speakers TURN IT UP If you play your music loud and want others to know, the R-Series speakers are the match for you. You’ll enjoy a center sound stage with speakers that play loud and clear without distortion. The R-Series speakers are tuned with an emphasis on the high- and low-end frequencies, so they deliver power while naturally producing bright, active sound. They are the perfect power and performance match for the R-Series subwoofers and amplifiers. General Features: 6.5-inch R-Series Component 2-way Car Speakers component speaker system includes two woofers, 2 tweeters, and 2 external crossovers Power Handling: Peak: 300 watts RMS: 100 watts 4 Ohms impedance Frequency response: 65Hz-40kHz Carbon Fiber Reinforced Polymer (CFRP) exclusive cone technology CFRP increases the speakers’ mid-bass performance and dynamic range CFRP is used as a tweeter diaphragm, enabling the system to perform up into the 45kHz range, making the speakers compliant with High-Resolution Audio playback Patented High-Amplitude Multi-Roll (HAMR) surround, for control and accuracy Ideal for tight installations and use matching speaker grills that are shallower as well (sold separately) Uses an in-line, passive design with a reduced footprint, which also contributes to easier installation Authorized Dealer 1-year Manufacturer's Warranty What's in the box: 2 Woofers Two 6-1/2" Adapter rings (includes GM/Chrysler) Two 6x8 Adapter rings 2 Woofer grilles 2 Grille badges 2 Tweeters (each has an attached 30" length of wire) 2 Tweeter grilles (installed) 2 Swivel flush mount housings (with tweeters installed) Two crossovers (each has attached input and output wires) 2 Flush mount retention rings 2 Stealth brackets 2 Foam self-adhesive pads 2 Foam self-adhesive rings Eight 1-1/8" Screws Eight 1/2" Screws 8 Speed-clips Eight M4x12mm Machine screws Four 5" Zip ties 2 Pieces of two-sided tape Warranty information Online product registration note Important Notice sheet Template and specs on the box Alpine R-S65C.2 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine R2-S65 6.5" Front Factory Speaker Replacement Kit Compatible Fit For 1999-2004 Chrysler 300M Package Includes: (1)Pair ALPINE R-S65.2 300 Watt 6.5" Car Audio Coaxial 2-Way Speakers (1)Metra 72-6512 Speaker Harness Connector for Chrysler Vehicles 90-07+Cherokee (1)Metra 82-6600 Chrysler 95-10 5.25" & 6.5" Speaker Mounting Bracket Plate+Cherokee Compatible with the following vehicles: Chrysler: 1999-2003 300M, 1995-2000 Cirrus, 1992-1999 Lebaron, 1995-2002 LHS, 1991-1996 New Yorker, 1996-2003 Sebring Coupe, 1995-2001 Sebring Sedan, 1991-2002 Town & Country, 2001-2003 Voyager. Dodge: 1991-2003 Caravan, 1994-1999 Dakota, 1993 Daytona, 1998-1999 Durango, 1998-2007 Ram Pick. Eagle: 1993-1997 Vision, 1997-2001 Cherokee, 1997-2003 Wrangler. Plymouth: 1996-2000 Breeze, 1995-2001 Neon, 1984-2000 Voyager   Alpine R2-S65 (R2S65) 300W MAX 100W RMS R-Series 6-1/2" 2-way Car Speakers TURN IT UP WITHOUT TURNING DOWN SOUND QUALITY If you play your music loud and want others to know, the R-Series speakers are the match for you. You will enjoy a center sound stage with speakers that play loud and clear without distortion. The R-Series speakers are tuned with an emphasis on the high- and low-end frequencies, so they deliver power while naturally producing bright, active sound. They are the perfect power and performance match for the R-Series subwoofers and amplifiers. General Features: 6.5" R-Series 2-way Coaxial Car Speakers carbon-fiber-reinforced polymer (CFRP) woofer Peak Power Handling: 600 watts per pair / 300 watts each RMS Power Handling: 200 watts per pair / 100 watts each Glass Fiber cone material Rubber HAMR Surround Composite Basket Hi-Res Audio Certified 1" Magnesium Hard Dome Tweeters CEA-2031 compliant: Yes Ferrite magnet motor structure Top-mount Depth: 2.48" Cutout Dimensions: 5.31" Impedance: 4 ohms Freque Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine R-S69.2 600W Peak, 200W RMS R-Series 6x9 Inch Coaxial 2-Way Speakers Bundle with METRA 72-7800 Speaker Connector Harness For 1986-2011 Honda Civic (2 items) R-Series speakers give you power and control. With an innovative material that delivers more output, the speakers produce a dependable performance for a loud and fun experience. If you play your music loud and want others to know, the R-Series speakers are the match for you. You’ll enjoy a center sound stage with speakers that play loud and clear without distortion. The R-Series speakers are tuned with an emphasis on the high- and low-end frequencies, so they deliver power while naturally producing bright, active sound. They are the perfect power and performance match for the R-Series subwoofers and amplifiers. The woofers have a large, 35-millimeter (mm) voice coil which allows for more coil windings to fit in the gap. This results in greater heat dissipation and increased power handling, for superior control and output. General Features: Alpine R-S69.2 R-Series 6x9 Inch Coaxial 2-Way Speakers Power Handling: RMS: 100 Watts Peak: 300 Watts Impedance: 4 Ohm Carbon-fiber reinforced polymer (CFRP) woofer Carbon-fiber reinforced polymer dome tweeter Frequency response: 60 Hz - 40 kHz Sensitivity: 90 dB Top-mount depth: 2-7/8" Grilles included Authorized Dealer 1-year Manufacturer's Warranty What's in the box: Two 2-way Speakers 2 Bottom mount brackets 2 Grilles 2 Grille badges Eight 1-1/8" Screws Eight M4x60mm Machine screws (with split lock washers attached) 8 Split lock washers 8 Flat washers Eight M4 Hex nuts 8 Speed clips Warranty information Important Notice Online product registration information Template and specs on the box Alpine R-S69.2 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov  

2 Alpine R-S69.2 600W Peak, 200W RMS R-Series 6x9 Inch Coaxial 2-Way Speakers + Metra 72-6512   R-Series speakers give you power and control. With an innovative material that delivers more output, the speakers produce a dependable performance for a loud and fun experience. If you play your music loud and want others to know, the R-Series speakers are the match for you. You’ll enjoy a center sound stage with speakers that play loud and clear without distortion. The R-Series speakers are tuned with an emphasis on the high- and low-end frequencies, so they deliver power while naturally producing bright, active sound. They are the perfect power and performance match for the R-Series subwoofers and amplifiers. The woofers have a large, 35-millimeter (mm) voice coil which allows for more coil windings to fit in the gap. This results in greater heat dissipation and increased power handling, for superior control and output. General Features: Alpine R-S69.2 R-Series 6x9 Inch Coaxial 2-Way Speakers Power Handling: RMS: 100 Watts Peak: 300 Watts Impedance: 4 Ohm Carbon-fiber reinforced polymer (CFRP) woofer Carbon-fiber reinforced polymer dome tweeter Frequency response: 60 Hz - 40 kHz Sensitivity: 90 dB Top-mount depth: 2-7/8" Grilles included Authorized Dealer 1-year Manufacturer's Warranty What's in the box: Two 2-way Speakers 2 Bottom mount brackets 2 Grilles 2 Grille badges Eight 1-1/8" Screws Eight M4x60mm Machine screws (with split lock washers attached) 8 Split lock washers 8 Flat washers Eight M4 Hex nuts 8 Speed clips Warranty information Important Notice Online product registration information Template and specs on the box Alpine R-S69.2 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

2 Pair Alpine S-S69C 520W Max (170W RMS) 6" x 9" Type-S Series 2-Way Component Car Speakers Alpine's S-Series Speakers have been redesigned with voice coil size and cone material upgrades to provide premium sound quality. The new benchmark for entry OEM upgrades! UNIVERSAL APPLICATIONSTo meet the needs of the most common applications in speaker replacement today, we’ve introduced a new 6x9-inch component speaker set to offer newer domestic trucks and cars the ability to upgrade the sound quality of their vehicle. With its innovative technology, this component set is a simple solution to getting Alpine sound in many of these vehicles today. EFFICIENT PERFORMANCE The S-Series speakers are the first in the industry to use CFRP (Carbon Fiber Reinforced Plastic), a very lightweight yet rigid material. The edges are naturally weaker than the center on a standard, off-the-shelf oval cone due to the elongated shape. Since the CFRP material is directional, it can be manipulated during molding to strengthen the normally weak cone areas. The result is rigidity throughout the cone that delivers accurate and efficient performance. The ability to manipulate the CFRP material during molding is currently exclusive to Alpine and the S-Series speakers. Alpine has three patent-pending procedures in support of this innovative manufacturing process. General Features: 6" x 9" Type-S Series 2-Way Component System Power Handling: Peak: 520 watts per set / 260 watts on each side RMS: 175 watts per set / 85 watts on each side Carbon-reinforced polypropylene cone Rubber surround 1" Silk dome tweeter CEA-2031 compliant speakers Top-mount Depth: 2-15/16" 4 ohms impedance Frequency Response: 65 - 22000 Hz Sensitivity: 90dB 1-year Warranty What is in the S-S69C package: S-S69C owner's manual 2 Woofers 2 Tweeters 2 Flush mount housings 2 Tweeter grilles Two 37" Tweeter wires with in-line crossovers  2 Flush mount retention rings 2 Stealth brackets Eight 1-3/16" Screws Eight M4x60mm Machine screws Eight M4 Nuts 8 Speed clips 8 Split lock washers 8 Spacers Warranty information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

2 Alpine S2-S65C 480W Peak (160W RMS) 6.5" Component Type  S-Series  2-way Component Speaker set with 1" Silk TweetersEFFICIENT PERFORMANCEThe S-Series speakers are the first in the industry to use CFRP (Carbon Fiber Reinforced Plastic), a very lightweight yet rigid material. The edges are naturally weaker than the center on a standard, off-the-shelf oval cone due to the elongated shape. Since the CFRP material is directional, it can be manipulated during the molding process to strengthen the typically weak cone areas. The result is rigidity throughout the cone that delivers accurate and efficient performance. The ability to manipulate the CFRP material during molding is exclusive to Alpine and the S-Series speakers. Alpine has three patent-pending procedures in support of this innovative manufacturing process.HAMR SURROUNDAlpine’s patented H.A.M.R. (High Amplitude Multi-Roll) surround is now found on the S-Series speakers. This proven technology increases excursion while maintaining accuracy and linearity. The multi-roll design allows for an even unfolding of the surround, which creates incredible linearity and colorization rejection.General Features: 6-1/2" 2-way Component System Car Speakers Peak Power Handling: 480 watts per set / 240 watts on each side RMS Power Handling: 160 watts per set / 80 watts on each side Polypropylene cone material Rubber speaker surround High Amplitude Multi-Roll surround technology HI-RES Certified 1" Silk Dome Tweeters Ferrite magnet motor structure Top-mount Depth: 2-5/16" Cutout Dimensions: 5-1/8" Impedance: 4 ohms Frequency Response: 55 - 40000 Hz Sensitivity: 88 dB Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the S2-S65C package: S2-S65C owner's manual 2 Woofers 2 Woofer mount adapter brackets 2 Tweeters 2 Flush mount housings 2 Tweeter grilles Two 37" Tweeter wires with in-line crossovers 2 Flush mount retention rings 2 Stealth brackets Eight 1-3/16" Screws Eight M4x6mm Machine screws 8 Speed clips Warranty information Online product registration information Important Notice sheet Template and specs on the box Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

2 Pairs Alpine S2-S69 520W Max (170W RMS) 6" x 9" Type S Series 2-Way Coaxial Car Speakers & Metra 72-8104 Speaker Wire Harness Connector Compatible Fit for Toyota FITS IN MOST COMMON APPLICATIONS To meet the needs of the most common applications in speaker replacement today, we've introduced a new 6x9-inch component set to offer newer domestic trucks and cars the ability to upgrade their vehicle's sound quality. This component, with its innovative technology, makes it a simple solution to getting Alpine sound in many of these vehicles on the road today. INCREASED DRIVING POWER AND CONTROL The S-Series speakers have a large voice coil. The 6.5-inch and 6x9-inch models have a 35-mm voice coil, and this large voice coil size increases their driving power and control of the motor. The S-Series speakers are the first in the industry to use CFRP (Carbon Fiber Reinforced Plastic), a very lightweight yet rigid material. The edges are naturally weaker than the center on a standard, off-the-shelf oval cone due to the elongated shape. Since the CFRP material is directional, it can be manipulated during the molding process to strengthen the generally weak cone areas. The result is rigidity throughout the cone that delivers accurate and efficient performance. The ability to manipulate the CFRP material during molding is currently exclusive to Alpine and the S-Series speakers. Alpine has three patent-pending procedures in support of this innovative manufacturing process. General Features: 6" x 9" Type S Series 2-Way Coaxial Car Speakers Power Handling: Peak: 520 watts per pair / 260 watts each RMS: 170 watts per pair / 85 watts each Recommended Power Range: 10 - 85 watts RMS per channel Carbon Fiber Reinforced Plastic (CFRP) Cone High Amplitude Multi-Roll (HAMR) Surround 1" Silk Dome Tweeter Rubber magnet boot cover CEA-2031 compliant speakers 35mm Voice Coil Top-mount Depth: 2-15/16" Cutout Dimensions: 5-29/32" x 8-3/4" 4 ohms Impedance Frequency Response: 65 - 22000 Hz Sensitivity: 90dB Compatible with the Alpine KTE-S69G Grille Authorized Dealer 1-year Manufacturer's Warranty What is in the S2-S69 package: Two 2-way speakers 2 Bottom mount brackets Two 12" Lengths of speaker wire Eight 1-3/16" Screws Eight M4x60mm Machine screws Eight M4 Nuts 8 Speed clips 16 Flat washers 8 Split lock washers Warranty information Online product registration information Template and specs on the box S-S69 owner's manual Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

2 Alpine X-S69C 6" x 9" Component System 720W Max, 240W RMS 6" x 9" X-Type 2-Way Component Car Speakers EXPERIENCE DETAIL YOU’VE NEVER HEARD BEFORE The new X-Series speakers combine proven technologies, superior materials, and innovative design to reproduce sound so accurately that you’ll feel right in front of the performance. HI-RESOLUTION AUDIO Hi-Res Audio is the next level of digital audio for music fans alike and requires an incredibly wide dynamic range to reproduce music with amazing realism and depth. The X-Series speakers are Hi-Rez compatible and, when paired with other X-Series components, provide an incredible Hi-Rez Audio experience. CARBON GRAPHITE TWEETER The tweeter’s diaphragm is built from a sheet of carbon graphite which enables it to reproduce frequency ranges in the upper 55kHz range, usually achieved using a harsher, hard dome tweeter like Aluminum or Titanium. Carbon graphite allows us to hit those High-rez audio-compatible frequencies while maintaining the softer, more damped sound qualities of a soft dome. NEW CONE MATERIAL The X-Series speaker cone is made from a tightly interwoven Nano-fiber material. The small diameter fibers create a damped, rigid cone structure while staying lightweight. Because of this light rigidity, the X-Series speaker can produce highly accurate sound while maintaining a soft tonality. The cone’s resistance to flex ensures it is very little to no discoloration of sound and phase shifts. The result is a highly accurate speaker that is well-staged in front of you. General Features: 6" x 9" X-Type 2-Way Component System Power Handling: Max: 720 W per set/ 360 W per side RMS: 240 W per set/ 120 W per side Recommended power range: 10 - 120W RMS Hi-Res Audio compatible Nano-fiber woofer cone H.A.M.R. surround 1" carbon graphite tweeter Tweeters swivel within flush mounts Adjustable tweeter attenuation: 0dB, +3dB, -3dB Adjustable tweeter phase: Normal or reverse A-Pole type neodymium magnet Top-mount depth: 3-1/16" Cutout Dimensions: 5-7/8" x 8-7/8" 4 ohms impedance Frequency Response: 45 - 50,000 Hz Sensitivity: 89 dB Authorized Dealer 1-year Manufacturer's Warranty What is in the X-S69C package 2 Woofers 2 Woofer grilles+ 2 Grille badges 2 Tweeters (each has a 26" length of wire attached) 2 Tweeter grilles (installed) 2 Surface mount housings (with tweeters installed) 2 Bottom mount brackets Two tweeter crossovers (each has attached 32" input and 14" output wires) 2 Rectangular adhesives backed pads (crossover) 2 Circular adhesive-backed discs (tweeter) Eight M4x60mm Machine screws (with washers attached) 8 Flat washers & 8 Split lock washers Eight 1-1/8" Screws & Eight 5/8" Screws 8 Speed-clips & 4 Speed nuts Four 5" Zip ties Warranty information Important Notice Online product registration information Templates and specs on the box X-S69C owner’s Manual ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine S-S69 6x9" Front + Rear Speaker Replacement Kit For 2001-2006 Dodge Stratus + Metra 72-6512 Speaker Harness Alpine S-S69 520W Max (170W RMS) 6" x 9" Type S Series 2-Way Coaxial Car Speakers FITS IN MOST COMMON APPLICATIONS To meet the needs of the most common applications in speaker replacement today, we've introduced a new 6x9-inch component set to offer newer domestic trucks and cars the ability to upgrade the sound quality in their vehicle. This component set with its innovative technology makes it a simple solution to getting Alpine sound in many of these vehicles on the road today INCREASED DRIVING POWER AND CONTROL The S-Series speakers have a large voice coil. The 6.5-inch and 6x9-inch models have a 35-mm voice coil, and this large voice coil size increases their driving power and control of the motor. The S-Series speakers are the first in the industry to use a material called CFRP (Carbon Fiber Reinforced Plastic), a very lightweight yet rigid material. On a standard, off-the-shelf oval cone, the edges are naturally weaker than the center due to the elongated shape. Since the CFRP material is directional, it can be manipulated during the molding process to strengthen the areas of the cone that are generally weak. The result is rigidity throughout the cone that delivers accurate and efficient performance. The ability to manipulate the CFRP material during the molding process is currently exclusive to Alpine and the S-Series speakers. Alpine has three patent-pending procedures in support of this innovative manufacturing process. General Features: 6" x 9" Type S Series 2-Way Coaxial Car Speakers Power Handling: Peak: 520 watts per pair / 260 watts each RMS: 170 watts per pair / 85 watts each Recommended Power Range: 10 - 85 watts RMS per channel Carbon Fiber Reinforced Plastic (CFRP) Cone High Amplitude Multi-Roll (HAMR) Surround 1" Silk Dome Tweeter Rubber magnet boot cover CEA-2031 compliant speakers 35mm Voice Coil Top-mount Depth: 2-15/16" Cutout Dimensions: 5-29/32" x 8-3/4" 4 ohms Impedance Frequency Response: 65 - 22000 Hz Sensitivity: 90dB Compatible with the Alpine KTE-S69G Grille Authorized Dealer 1-year Manufacturer's Warranty What is in the box: Two 2-way speakers 2 Bottom mount brackets Two 12" Lengths of speaker wire (each has quick slides on one end and bare wire on the other) Eight 1-3/16" Screws Eight M4x60mm Machine screws (each screw has a lock washer attached) Eight M4 Nuts 8 Speed clips 16 Flat washers 8 Split lock washers 8 Spacers Warranty information Online product registration information Important Notice sheet Template and specs on the box Alpine S-S69 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov