All Car Amplifiers (436)

Rockford Fosgate Punch P500X1BD 500W RMS Punch Series Monoblock Class D Car Power Amplifier The Punch P500X1bd is a mono amplifier capable of 500 Watts into a 1-Ohm load. The Class-BD technology produces bass more efficiently over traditional amps, and its frequency response allows it to be optimized for subwoofers. General Features Punch BD Series Monoblock Class BD Car Amplifier RMS Power Rating: 4 ohms: 150 watts x 1 chan. 2 ohms: 300 watts x 1 chan. 1 ohm: 500 watts x 1 chan. CEA-2006 compliant amplifier MOSFET power supply Muted turn-on. Cast aluminum heatsink. 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protect indicators. Nickel-plated captive C-clamp terminals. Ultra-efficient Class BD circuitry to maximize amplifier power efficiency. On-board differential inputs eliminate noise picked up by the signal cable. Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately) MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span. Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances. Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low. DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowers the operating temperature and potential for noise-like circuit boards designed by aerospace manufacturers. Input sensitivity: 150mV - 12V On-board Punch EQ with +18dB boost @ 45Hz. Variable low-pass filter: 50-250 Hz Selectable infrasonic filter: off / 28 Hz Frequency response: 20 - 250 Hz Total Harmonic Distortion: <1.0% Dimensions: 11"L x 7-3/4"W x 2-3/8"H 8 AWG to 18 AWG speaker wire output terminals Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the P500X1bd box: Mono subwoofer amplifier Four 1-1/2" Self-tapping screws 2.5mm Allen wrench Quick setup instructions Certificate of Performance P500X1bd owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca

Alpine X-A70F 700 W RMS X-Series Class-D 4-Channel 2 ohm Stable AmplifierAlpine introduces the all-new X-Series of high-grade speakers and amplifiers. These products have been engineered and tuned to create a perfect match for extraordinarily dynamic, realistic sound reproduction, and a spatial sound impression.The all-new X-Series amplifiers set a new standard for sound quality performance and power output in a very compact design. Available in mono, four-channel, and five-channel configuration, these amps are a perfect match for the all-new X-Series speakers and subwoofers.General Features: Alpine X-Series X-A70F Class-D Full Range 2 ohm Stable 4-Channel Amplifier RMS Power Rating: 4 ohms: 120 watts x 4 Channel 2 ohms: 175 watts x 4 Channel 1 ohm: ------------N/A----------- Bridged, 4 Ohms: 350 Watts X 2 Channel Total power output: 700 watts CEA-2006 Compliant Amplifier Hi-Res Audio compatible Wired remote level control, Alpine RUX-KNOB.2, available Included plastic covers available to offer a brushed aluminum finish around the edges LED power (green) and protect (red) indicators Soft start turn-on 4/3/2 channel operation Speaker-level (high-level) inputs Preamp Outputs 3-way protection circuitry (thermal, overload, and speaker short protection) Dual speaker terminals simplify the hookup of multiple speakers Heavy-duty aluminum alloy heat-sink Input sensitivity High level: .4 - 10V Low level: .1 - 4V Frequency Response: 10 - 60,000 Total Harmonic Distortion (THD): .07% Signal to Noise Ratio: >106dB Variable low-pass filter: 50 - 400Hz, -24dB/octave Variable subsonic filter: 50 - 40Hz, -24dB/octave Variable Bass Boost: 0 to +12 dB bass boost at 50 Hz Fuse Rating: 35A x 3 4 gauge power and ground wiring are recommended for installation. Contact us for information regarding a discount on select amplifier kits from our website when purchased together with this amplifier. Dimensions: 11-3/4"W x 7-5/8"L x 2"H Authorized Dealer 1-year Manufacturer's Warranty What is in the X-A70M package: 4-Channel amplifier Two 35A ATO fuses (installed) Terminal Cover Left Terminal Cover Right Terminal Cover Front Battery connector plug 2 Speaker connector plugs Logo Plate (self-adhesive) 4 Self-tapping screws (Length 3/4") 2mm Allen wrench 4mm Allen wrench Owner's Manual Alpine Verification Certificate Limited Warranty To Customers sheet X-A70M owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine KTP-445A Power Pack Head Unit Amplifier and Backup Camera Bundle. 4-Channel Compact Amp Increases Alpine Head Unit Power up to 150 Percent - 90 Watts x 4 Channels, fits iLX-W650 and Others Bundle Package: Alpine KTP-445A Power Pack Amp Absolute Waterproof Angle Backup Camera Alpine KTP-445A Plug and Play Head Unit Power Pack for Use w/ 2005-Up Alpine Head Units with a Black Power Harness The KTP-445A Power Pack amplifies power output on select 2005 and newer Alpine head units, resulting in up to a 150 percent power increase over the original power from the head unit's built-in amplifier. The compact size lets the KTP-445A fit where most amplifiers won’t. The KTP-445A comes equipped with direct plug-in connectors for select 2005 and newer Alpine head units and it fits behind the dash of most vehicles. It's small and compact at only 7-7/16” x 1-1/2” x 2-1/2”. Its size and flexible wires make the Power Pack an easy choice to save space. To ensure that Alpine sound quality is heard, we’ve created a platform that offers an unbelievably low noise floor, taking extra care to ensure a clean signal path, with no extraneous interference. The result: The Power Pack boasts a 1-watt signal-to-noise ratio of 82dB or better. General Features: Alpine Power Pack 4-Channel Class D for Select In-Dash Receivers Plug-and-play design for compatible Alpine head units (2005 - Up, Black 16 Pin) RMS Power Rating: 4 ohms: 45 watts x 4 Channel Total RMS power output: 180 watts CEA-2006 compliant amplifier Increases the output of an Alpine head unit without having to install a full-size amplifier and amp install kit The fast and easy solution to higher power aftermarket sound High-efficiency digital circuit design Gain optimized for Alpine head units Plugs directly into the wiring harness of the Alpine receiver Fast and simple installation 4-channel operation for four speakers Is not compatible with factory amplifiers Frequency response: 20-20,000 Hz Signal to Noise Ratio: 84 dBA Fuse Rating: 15A x 1 Includes both Amp-to-receiver and Amp-to-vehicle Harnesses Dimensions: 7-13/16D x 2-9/16"W x 1-1/2"H Authorized Dealer 1-year Manufacturer's Warranty What is in the KTP-445A package: Head Unit Power Pack (15A fuse installed) 39" Amp-to-receiver harness (male 16-pin connector on each end) 31" Amp-to-vehicle harness (male 16-pin connector on one end and a female 16-pin connector on the other end) 2 Brackets 4 Screws 4 Wire-ties Installation Diagram Online Product Registration Limited Warranty Information KTP-445A Power Pack owner's manual Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine KTP-445A Power Pack Head Unit Amplifier and Backup Camera Bundle. 4-Channel Compact Amp Increases Alpine Head Unit Power up to 150 Percent - 90 Watts x 4 Channels, fits iLX-W650 and Others Bundle Package: Alpine KTP-445A Power Pack Amp Absolute Waterproof Angle Backup Camera Alpine KTP-445A Plug and Play Head Unit Power Pack for Use w/ 2005-Up Alpine Head Units with a Black Power Harness The KTP-445A Power Pack amplifies power output on select 2005 and newer Alpine head units, resulting in up to a 150 percent power increase over the original power from the head unit's built-in amplifier. The compact size lets the KTP-445A fit where most amplifiers won’t. The KTP-445A comes equipped with direct plug-in connectors for select 2005 and newer Alpine head units and it fits behind the dash of most vehicles. It's small and compact at only 7-7/16” x 1-1/2” x 2-1/2”. Its size and flexible wires make the Power Pack an easy choice to save space. To ensure that Alpine sound quality is heard, we’ve created a platform that offers an unbelievably low noise floor, taking extra care to ensure a clean signal path, with no extraneous interference. The result: The Power Pack boasts a 1-watt signal-to-noise ratio of 82dB or better. General Features: Alpine Power Pack 4-Channel Class D for Select In-Dash Receivers Plug-and-play design for compatible Alpine head units (2005 - Up, Black 16 Pin) RMS Power Rating: 4 ohms: 45 watts x 4 Channel Total RMS power output: 180 watts CEA-2006 compliant amplifier Increases the output of an Alpine head unit without having to install a full-size amplifier and amp install kit The fast and easy solution to higher power aftermarket sound High-efficiency digital circuit design Gain optimized for Alpine head units Plugs directly into the wiring harness of the Alpine receiver Fast and simple installation 4 channel operation for four speakers Is not compatible with factory amplifiers Frequency response: 20-20,000 Hz Signal to Noise Ratio: 84 dBA Fuse Rating: 15A x 1 Includes both Amp-to-receiver and Amp-to-vehicle Harnesses Dimensions: 7-13/16D x 2-9/16"W x 1-1/2"H Authorized Dealer 1-year Manufacturer's Warranty What is in the KTP-445A package: Head Unit Power Pack (15A fuse installed) 39" Amp-to-receiver harness (male 16-pin connector on each end) 31" Amp-to-vehicle harness (male 16-pin connector on one end and a female 16-pin connector on the other end) 2 Brackets 4 Screws 4 Wire-ties Installation Diagram Online Product Registration Limited Warranty Information KTP-445A Power Pack owner's manual Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine KTP-445A Plug and Play Head Unit Power Pack for Use w/ 2005-Up Alpine Head Units with a Black Power Harness The KTP-445A Power Pack amplifies power output on select 2005 and newer Alpine head units, resulting in up to a 150 percent power increase over the original power from the head unit's built-in amplifier. Compact size lets the KTP-445A fit where most amplifiers won’t. The KTP-445A comes equipped with direct plug-in connectors for select 2005 and newer Alpine head units and it fits behind the dash of most vehicles. It's small and compact at only 7-7/16” x 1-1/2” x 2-1/2”. Its size and flexible wires make the Power Pack an easy choice to save space. In order to ensure that Alpine sound quality is heard, we’ve created a platform that offers an unbelievably low noise floor, taking extra care to ensure a clean signal path, with no extraneous interference. The end result: The Power Pack boasts a 1 Watt Signal-to-Noise Ratio of 82dB or better. General Features: Alpine Power Pack 4-Channel Class D for Select In-Dash Receivers Plug-and-play design for compatible Alpine head units (2005 - Up, Black 16 Pin) RMS Power Rating: 4 ohms: 45 watts x 4 Channel Total RMS power output: 180 watts CEA-2006 compliant amplifier Increases the output of an Alpine head unit without having to install a full-size amplifier and amp install kit The fast and easy solution to higher power aftermarket sound High-efficiency digital circuit design Gain optimized for Alpine head units Plugs directly into the wiring harness of the Alpine receiver Fast and simple installation 4 channel operation for four speakers Is not compatible with factory amplifiers Frequency response: 20-20,000 Hz Signal to Noise Ratio: 84 dBA Fuse Rating: 15A x 1 Includes both Amp-to-receiver and Amp-to-vehicle Harnesses Dimensions: 7-13/16D x 2-9/16"W x 1-1/2"H Authorized Dealer 1-year Manufacturer's Warranty What is in the KTP-445A package: Head Unit Power Pack (15A fuse installed) 39" Amp-to-receiver harness (male 16-pin connector on each end) 31" Amp-to-vehicle harness (male 16-pin connector on one end and a female 16-pin connector on other ends) 2 Brackets 4 Screws 4 Wire-ties Installation Diagram Online Product Registration Limited Warranty Information KTP-445A Power Pack owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Cerwin-Vega CVPRO3K 3000W Full Range Class D Monoblock Amp Subwoofer Amplifier Latest High-Efficiency Class D Topology. Full Range Class D Monoblock Amplifier. Compact Size with Ambient backlit logo. RCA “Pass Thru” output for easy system expansion. Fully Variable Crossovers (12dB per octave). 3000WX1@1Ω. 2050WX1@2Ω. 1100WX1@4Ω. 15-20KHz Frequency Response. LPF Filter 80-20KHz. 12dB Crossover Slope. General Features: CVP Pro Monoblock Class D Car Amplifier RMS Power Rating: 4 ohms: 1100 watts x 1 chan. 2 ohms: 2050 watts x 1 chan. 1 ohm: 3000 watts x 1 chan. Wired remote bass level control included Variable Bass Boost 0 to +12 dB bass boost at 50 Hz Mono channel operation Speaker-level (high-level) inputs with signal sensing for automatic turn-on Dimensions: 8.85"W 7.95 "L 2.61"H Authorized Internet Dealer 1-year Manufacturer's Warranty Specification: Amplifier Monoblock MAX Power Rating 6000 W MAX RMS Power (1Ω) 3000 RMS Power(2Ω) 2050 RMS Power (4Ω) 1100 Topology Full-Range Class D Frequency Response 15-20KHz Power Supply Full PWM Power Supply (Threshold) 10.0VDC– 17.0VDC Idle Current (2.6A) Distortion - THD (1KHz@4Ω) 0.1% Distortion - S/N Ratio (A weight @ 1W) -90dBA Distortion - S/N Ratio (A weight @ FP) -105dBA Input Sensitivity 0.2V – 5.0V Input Impedance - Low Input Level 20 KΩ Output Impedance 0.0297 Ω Damping Factor (50Hz@4Ω) >150 Bandwidth (-3dB) 15Hz-20KHz LPF Filter 80-20KHz Crossover (-12 dB/ Oct) Variable High-Pass 50Hz-20KHz Crossover (-12 dB/ Oct) Variable Low-Pass 15Hz-1KHz Crossover (-12 dB/ Oct) Variable Sub-Sonic 15Hz-1KHz FUSE Ratings - ATC 150A Dimension - Length x Width x Height - Inches(mm) 7.95” x 8.85” x 2.61” ( 202 x 225 x 66.5mm ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine KTA-30MW Car Amplifier Mono 300-Watt RMS Weather Resistant Tough Power Pack Amplifier A TOUGH MINI AMP THAT PACKS A PUNCH Get big amp performance in a compact, resilient package. With Alpine’s exclusive technology, Dynamic Peak Power (D.P.P.), the KTA-30MW Weather Resistant Tough Power Pack is sure to deliver powerful bass output for subwoofers used in those open cab vehicles and toys. This small and efficient amplifier can be installed with an aftermarket or factory head unit while adding up to 600 watts of D.P.P. power. Its weather resistance makes the KTA-30MW a good choice for use in exposed installations like side-by-sides, boats, open-top vehicles, and motorcycle saddlebags. A SOUND SYSTEM BOOST WITHOUT THE BIG SPACE COMMITMENT The KTA-30MW is perfect for when you want to add subwoofer power but don’t have space for a large amplifier. It is compatible with an aftermarket or factory head unit and provides up to 600 DPP watts to the subwoofer of your choice. HALF THE SIZE OF OUR SMALLEST TRADITIONAL AMPLIFIERS The KTA-30MW measures just 9-3/16” (W) x 1-5/8” (H) x 3-3/4” (D), so its small footprint lets it fit where most amplifiers won’t, like under the dash or in the glove compartment, installed under the dash of a side-by-side, placed in the saddlebag of a motorcycle, or used in other places where space is an issue. General Features: Alpine KTA-30MW Class D Monoblock Weather Resistant Power Pack Amplifier 300 Watts RMS X 1 @ 4 Ohms Power Handling 600 Watts RMS X 1 @ 2 Ohms Power Handling CTA-2006 compliant Frequency Response: 20-400 Hz Total Harmonic Distortion (THD): <1% Signal to Noise Ratio: 83dB Variable Low Pass filter 50-400Hz @ -24dB/Oct. Variable Bass Boost (0-12 dB at 50 Hz) Fuse Rating: 25A Weather-resistant (IP66 rating) Dynamic Peak Power (D.P.P.) technology intelligently adjusts the gain to automatically adapt to musical needs Dimensions: 7” W x 3.5” H x 1.25” D Authorized Dealer 1-year Manufacturer's Warranty What is in the box: Mono amplifier 14" Power/signal harness (26-pin connector on one end and bare wires + RCAs on other ends) 4 Self-tapping screws (Length 3/4") Connection sheet Limited Warranty sheet Alpine KTA-30MW owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine BBX-F1200 600W Max (280W RMS) 2-ohm Stable 4 Channel Class-A/B Amplifier This new BBX amplifier gives you Alpine power performance at an amazing price. And they’re designed to fit easily in virtually any system. High Power, Great Value This amp delivers high output power and exceptional performance for their class. It's a great way to expand your sound system on a limited budget. High Pass and Low Pass Filters These two filters let you set the frequency points for the high, mid, and bass ranges to match your speakers and ensure optimum efficiency. Performance With Bass EQ, you can maximize the performance of your system and get even more powerful bass. General Features: Alpine BBX-F1200 Class-A/B 2-ohm Stable 4-Channel Amplifier RMS Power Rating: 4 ohms: 50 watts x 4 channel 2 ohms: 70 watts x 4 channel 1 ohm: ------------N/A------------ Bridged, 4 ohms: 130 watts x 2 channel Total power output: 600 watts Pulse Width Modulated MOSFET power supply LED power (green) and protect (red) indicators Soft start turn-on 4/3/2 or channel operation 3-way protection circuitry (thermal, overload, and speaker short protection) Dual speaker terminals simplify the hookup of multiple speakers Heavy-duty aluminum alloy heat-sink Input sensitivity: .2V - 8V Frequency Response: 5 - 50000 Hz Total Harmonic Distortion (THD): <1% Signal Noise Ratio: 95dB Variable high-pass filter: 50 - 500 Hz Variable low-pass filter: 50 - 500 Hz Variable Bass Boost: 0 to +12 dB bass boost Fuse Rating: 40A x 1 Dimensions: 9.4"W x 12.9"L x 2"H Authorized Dealer 1-year Manufacturer's Warranty What's in the BBX-F1200 package: BBX-F1200 owner's manual Four-Channel amplifier Owner's manual (English/ French/ Spanish) Alpine Verification Certificate Warranty information Power supply note Online product registration information Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.