All Alpine Car Subwoofers (130)

2 Alpine R-Series next generation R2-W10D4 10" 4 Ohm 2250 Max, 750W RMS DVC Car Audio Subwoofer The new 2022 R-Series subwoofers are here - drawing from decades of Subwoofer engineering experience. They deliver deep, clean, accurate bass and feature Alpine’s HAMR Surround for maximum cone excursion, delivering tons of bass output. The new ceramic dust cap is lightweight and rigid, keeping distortion at an absolute minimum. The enlarged motor structure ensures better woofer control for a strong, clean bass response. General Features: 10" Dual 4 ohms Type-R Series Series Subwoofer RMS Power Handling: 750 watts Peak Power Handling: 2250 watts Kevlar Reinforced Pulp Paper Cone High-Amplitude Multi-Roll (H.A.M.R) Surround Push-Type Speaker Terminals (Up To 8AWG Wire Size) Oversized Dust Cap 2.6" High-Temperature Voice coil 20 mm Xmax 123 oz. Double Stacked Ferrite magnet motor structure Frequency Response: 26 - 200 Hz Resonance Frequency (Fs): 32 Hz Sensitivity: 82.8 dB Sealed box volume: .4 cubic feet - .85 cubic feet Ported box volume: .75 cubic feet - 1.3 cubic feet Top-mount depth: 6" Cutout diameter: 9.6" CTA-2031 Compliant: Yes Authorized Internet Dealer Alpine KTE-10G Optional Protective subwoofer grille 1-year Manufacturer's Warranty What is in the R2-W10D4 package: R2-W10D4 owner's manual One 10" Dual 4-ohm voice coil subwoofer Plastic trim ring Two 4.5" jumper wires Application guide Online product registration information Warranty Information  Important Notice  ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

  Alpine Halo R2-SB10V 750W RMS 10" Halo Series Linkable Ported Loaded Subwoofer Enclosure A subwoofer enclosure that sounds as good as it looks. Alpine’s preloaded, linkable subwoofer enclosures give you powerful performance with the unique Alpine Halo design and ProLink™. The new 2nd generation R-Series subwoofers take bass performance to extreme levels, delivering thunderous, ground-pounding bass. With Alpine’s enhanced sound performance, the R-Series subwoofers are highly accurate, creating a perfectly matched sound system for R-Series amplifiers and speakers – building an overall cohesive theme with its entire full-range Hi-RES Audio certified system. The R2-SB10V is designed for amplifier compatibility with 20hm loads. General Features: Dual 10" Vented / Ported Subwoofer Enclosure Power Handling: Peak: 2250 watts Total RMS: 750 watts Total Preloaded with single 10" Subwoofers Vented / Ported Square/Rectangle enclosure Enclosure Dimensions: 14.5" TD x BD x 16" W x 12.68" H Groundbreaking Alpine Halo Design ProLink™ ported enclosure design Optimal Sound Performance Includes preloaded R-W10D4 10” R-Series subwoofer CARB-compliant 3/4-inch MDF construction Premium black carpet Silver Alpine embossed side logo badge Brushed aluminum finished metallic front baffle Authorized Internet Dealer 1-year Manufacturer's Warranty Subwoofer Features: Frequency Response: 24 - 200 Hz Sensitivity: 85 dB Enclosure Features: 10" Square/Rectangle Enclosure Box Finish: Carpet What's in the R2-SB10V package: R2-SB10V Owner's manual Ported enclosure loaded with one R2-W10D4 subwoofer driver Warranty information Product registration information Safety notice ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

  Alpine Halo R2-SB12V 750W RMS 12" Halo Series Linkable Ported Loaded Subwoofer Enclosure A subwoofer enclosure that sounds as good as it looks. Alpine’s preloaded, linkable subwoofer enclosures give you powerful performance with the unique Alpine Halo design and ProLink™. The new 2nd generation R-Series subwoofers take bass performance to extreme levels, delivering thunderous, ground-pounding bass. With Alpine’s enhanced sound performance, the R-Series subwoofers are highly accurate, creating a perfectly matched sound system to R-Series amplifiers and R-Series speakers – building an overall cohesive theme with its entire full-range Hi-RES Audio certified system. The R2-SB12V is designed for amplifier compatibility with 20hm loads. General Features: Dual 12" Vented / Ported Subwoofer Enclosure Power Handling: Peak: 2250 watts Total RMS: 750 watts Total Preloaded with single 12" Subwoofers Vented / Ported Square/Rectangle enclosure Enclosure Dimensions: 15" TD x BD x 17" W x 14.62" H Groundbreaking Alpine Halo Design ProLink™ ported enclosure design Optimal Sound Performance Includes preloaded R-W12D4 12” R-Series subwoofer CARB-compliant 3/4-inch MDF construction Premium black carpet Silver Alpine embossed side logo badge Brushed aluminum finished metallic front baffle Authorized Internet Dealer 1-year Manufacturer's Warranty Subwoofer Features: Frequency Response: 24 - 200 Hz Sensitivity: 85 dB Enclosure Features: 12" Square/Rectangle Enclosure Box Finish: Carpet What's in the R2-SB12V package: R2-SB12V Owner's manual Ported enclosure loaded with one R2-W12D4 subwoofer driver Warranty information Product registration information Safety notice ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.  

2 Alpine R2-W12D4 2250W Max (750W RMS) 12" R-Series Dual 4-Ohm Car Subwoofer The new 2022 R-Series subwoofers are here - drawing from decades of Subwoofer engineering experience. They deliver deep, clean, accurate bass and feature Alpine’s HAMR Surround for maximum cone excursion, delivering tons of bass output. The new ceramic dust cap is lightweight and rigid, keeping distortion at an absolute minimum. The enlarged motor structure ensures better woofer control for a strong, clean bass response. General Features: 12" Dual 4 ohm Type-R Subwoofer Peak Power Handling: 2250watts RMS Power Handling: 750 watts Recommended power range: 300 - 750W RMS CTA-2031 compliant power ratings Parabolic pulp/kevlar cone H.A.M.R. surround Polypropylene, mica, and talc dust cap Reinforced cone neck and spider joint Cast aluminum frame with integral shorting sleeve 8AWG push terminals with VC configuration jumpers 2.6" High excursion overhung voice coil 127 oz. Strontium ferrite segmented magnet Top-mount depth: 6-3/8" Cutout diameter: 10-7/8" Frequency Response: 24 - 200Hz Sensitivity: 84.3dB Resonance Frequency (Fs): 27Hz Authorized Dealer 1-year Manufacturer's Warranty What's in the R2-W12D4 package: R2-W12D2 owner's manual One 12" Dual 4-ohm voice coil subwoofer Two 3" jumper cables R-Series Subwoofer Application Guide Online product registration information Warranty Information https://www.youtube.com/watch?v=ihjWBSOYVxE&t=179s ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine RS-W12D2 12" 1200 Watts Shallow Mount Dual 2-Ohm Voice Coil R Series subwooferAlpine's RS-W12D2 R-Series With an ultra-shallow subwoofer design and powerful sound output, the R-Series Shallow Subwoofers give you the best of both worlds in size and sound. General Features: 12" Dual 2 ohms Type-R Series Shallow Subwoofer Peak Power Handling: 1200 watts RMS Power Handling: 600 watts Polypropylene with aluminum dust cap Cone Butyl Rubber Surround Alpine Gen2 DD Linear Magnetic Circuit Cast aluminum basket 4" High-Temperature Voice coil 20 mm Xmax Neodymium magnet motor structure Frequency Response: 27 - 200 Hz Resonance Frequency (Fs): 26 Hz Sensitivity: 81 dB Top-mount depth: 3.25" Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the RS-W12D2 package: RS-W12D2 Owner's Manual 12" R-Series Shallow Subwoofer Warranty Information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine RS-W12D4 12" 1200 Watts Shallow Mount Dual 4-Ohm Voice Coil R Series subwooferAlpine's RS-W12D4 R-Series With an ultra-shallow subwoofer design and powerful sound output, the R-Series Shallow Subwoofers give you the best of both worlds in size and sound. General Features: 12" Dual 4 ohms Type-R Series Shallow Subwoofer Peak Power Handling: 1200 watts RMS Power Handling: 600 watts Polypropylene with aluminum dust cap Cone Butyl Rubber Surround Alpine Gen2 DD Linear Magnetic Circuit Cast aluminum basket 4" High-Temperature Voice coil 20 mm Xmax Neodymium magnet motor structure Frequency Response: 27 - 200 Hz Resonance Frequency (Fs): 26 Hz Sensitivity: 81 dB Top-mount depth: 3.25" Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the RS-W12D4 package: RS-W12D4 Owner's Manual 12" R-Series Shallow Subwoofer Warranty Information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine RS-W10D2 12" 1200 Watts Shallow Mount Dual 2-Ohm Voice Coil R Series subwooferAlpine's RS-W10D2 R-Series With an ultra-shallow subwoofer design and powerful sound output, the R-Series Shallow Subwoofers give you the best of both worlds in size and sound. General Features: 10" Dual 2 ohms Type-R Series Shallow Subwoofer Peak Power Handling: 1200 watts RMS Power Handling: 600 watts Polypropylene with aluminum dust cap Cone Butyl Rubber Surround Alpine Gen2 DD Linear Magnetic Circuit Cast aluminum basket 4" High-Temperature Voice coil 20 mm Xmax Neodymium magnet motor structure Frequency Response: 29 - 200 Hz Resonance Frequency (Fs): 28 Hz Sensitivity: 81 dB Top-mount depth: 3.25" Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the RS-W10D2 package: RS-W10D2 Owner's Manual 10" R-Series Shallow Subwoofer Warranty Information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

2) Alpine SWT-10S4 10" 1000W Shallow Slim Subwoofers+AudioControl The Epicenter Bass Processor 2 Alpine SWT-10S4 1000W Peak 10" SWT Series Single 4-ohm Shallow Mount Subwoofer Right size, Right sound. Here's a big bass breakthrough for truck lovers. Alpine engineered their SWT-10S4 10" subwoofer to go behind your seat and sound especially good in the limited space of a truck cab. This deep-sounding, high-performance sub works well in shallow enclosures that'll fit behind or under the seat in your truck. A "high amplitude" surround allows more cone travel than a regular sub, so the SWT-10S4 can push more air and play louder. Airflow-insured subs get hot as they play, and the heat usually gets vented away via a port in the back of the sub's pole piece. Alpine recessed the pole port and added cooling air vents on the sides of the frame, allowing you to use an enclosure with an inside clearance of as little as 4-3/16" without blocking critical airflow. An SWT-10S4 will work well in a ported or sealed box so you can get your favorite bass tone, boomy, or tight. The power takes for top performance, and you'll want to pick an amplifier that delivers between 300 and 500 watts RMS at 4 ohms. This single voice coil, the 4-ohm sub, will draw the maximum output power from a subwoofer amplifier when used along with a second SWT-10S2 in a system. If you plan on running a pair, look for an amp that delivers between 600 and 1000 watts RMS at 4 ohms. General Features: 10" SWT Series Single 4-ohm Shallow Mount Truck Subwoofer Peak Power Handling: 1,000 watts RMS Power Handling: 350 watts Recommended Power Range: 100W - 350W Poly-Mica Dust Cap & Pulp-Kevlar Polyurethane Foam Surround H.A.M.R. Surround Technology Spiral Cut Aluminum Former 65mm Voice Coil with High-Temp 4-Layer SVC Winding 8AWG Push Terminals Top-mount depth: 4-3/16" Mounting Diameter: 8-15/16'' Frequency Response: 30 - 200 Hz Sensitivity: 84.8 dB Authorized Dealer 1-year Manufacturer's Warranty What is in the SWT-10S4 package: SWT-10S4 owner's manual 10" Thin-mount subwoofer Online product registration information Warranty information Audio Control THE EPICENTER 2-Channel Concert Series Digital Bass Restoration Processor with Bass Remote Your MP3 player thinks your car stereo is a pair of headphones, so it removes the bass! The Epicenter restores the earth-shaking power and heart-pounding bass your subwoofers crave. Give your subwoofers the juice to go lower and hit harder.  The Epicenter uses a bass circuit to drive your subwoofers lower, grabbing the attention of every eye on the boulevard. General Features: Active Epicenter Series 2 channel digital bass restoration and line output converter Designed to integrate with after-market or factory OEM systems Digital bass restoration restores bass roll-off in factory systems Speaker level inputs Bass/Gain level remote: Yes Signal-Sensing turn-on: Yes Preamp outputs: 1 pair Bass Maximizer circuitry Multiple turn-on options PFM Subsonic Filter bypass option Selectable impedance load: 20, 60, 20k ohms Frequency response: 10 - 100,000 Hz Subsonic filter: 20 Hz, 12/dB octave Signal-to-noise ratio: >130 dB Total harmonic distortion (THD): 0.003% Fuse Rating: 1A x 1  Dimensions: 8-1/16"W x 1-1/4"H x 6-3/4"H Weight: 1.70lbs Authorized Internet Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) What is in the THE EPICENTER package: The Epicenter owner's manual Pre-amp Bass Restoration Processor black Remote dash mount control Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine SWT-10S2 1000W Peak 10" SWT Series Single 2-ohm Shallow Mount Subwoofer Right size, Right sound. Here's a big bass breakthrough for truck lovers. Alpine engineered their SWT-10S2 10" subwoofer to go behind your seat and sound especially good in the limited space of a truck cab. This deep-sounding, high-performance sub works well in shallow enclosures that'll fit behind or under the seat in your truck. A "high amplitude" surround allows more cone travel than a regular sub, so the SWT-10S2 can push more air and play louder. Airflow-insured subs get hot as they play, and the heat usually gets vented away via a port in the back of the sub's pole piece. Alpine recessed the pole port and added cooling air vents on the sides of the frame, allowing you to use an enclosure with an inside clearance of as little as 4-3/16" without blocking critical airflow. An SWT-10S4 will work well in a ported or sealed box so you can get your favorite bass tone, boomy or tight. The power takes for top performance, and you'll want to pick an amplifier that delivers between 300 and 500 watts RMS at 4 ohms. This single voice coil, the 4-ohm sub, will draw the maximum output power from a subwoofer amplifier when used along with a second SWT-10S2 in a system. If you're planning on running a pair, look for an amp that delivers between 600 and 1000 watts RMS at 2 ohms. General Features: 10" SWT Series Single 2-ohm Shallow Mount Truck Subwoofer Peak Power Handling: 1,000 watts RMS Power Handling: 350 watts Recommended Power Range: 100W - 350W Poly-Mica Dust Cap & Pulp-Kevlar Polyurethane Foam Surround H.A.M.R. Surround Technology Spiral Cut Aluminum Former 65mm Voice Coil with High-Temp 4-Layer SVC Winding 8AWG Push Terminals Top-mount depth: 4-3/16" Mounting Diameter: 8-15/16'' Frequency Response: 30 - 200 Hz Sensitivity: 84.8 dB Authorized Dealer 1-year Manufacturer's Warranty What is in the SWT-10S2 package: SWT-10S2 owner's manual 10" Thin-mount subwoofer Online product registration information Warranty information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine R2-W10D4 2250W Max (750W RMS) 10" R-Series Dual 2-Ohm Car Subwoofer with Absolute Vented Subwoofer Enclosure Box The new 2022 R-Series subwoofers are here - drawing from decades of Subwoofer engineering experience. They deliver deep, clean, accurate bass and feature Alpine’s HAMR Surround for maximum cone excursion, delivering tons of bass output. The new ceramic dust cap is lightweight and rigid, keeping distortion at an absolute minimum. The enlarged motor structure ensures better woofer control for a strong, clean bass response. General Features: 10" Dual 4 ohms Type-R Series Series Subwoofer RMS Power Handling: 750 watts Peak Power Handling: 2250 watts Kevlar Reinforced Pulp Paper Cone High-Amplitude Multi-Roll (H.A.M.R) Surround Push-Type Speaker Terminals (Up To 8AWG Wire Size) Oversized Dust Cap 2.6" High-Temperature Voice coil 20 mm Xmax 123 oz. Double Stacked Ferrite magnet motor structure Frequency Response: 26 - 200 Hz Resonance Frequency (Fs): 32 Hz Sensitivity: 82.8 dB Sealed box volume: .4 cubic feet - .85 cubic feet Ported box volume: .75 cubic feet - 1.3 cubic feet Top-mount depth: 6" Cutout diameter: 9.6" CTA-2031 Compliant: Yes Authorized Internet Dealer Alpine KTE-10G Optional Protective subwoofer grille 1-year Manufacturer's Warranty What is in the R2-W10D4 package: R2-W10D4 owner's manual One 10" Dual 4-ohm voice coil subwoofer Plastic trim ring Two 4.5" jumper wires Application guide Online product registration information Warranty Information  Important Notice  Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine SWT-10S2 1000W Peak 10" SWT Series Single 2-ohm Shallow Mount Subwoofer Right size, Right sound. Here's a big bass breakthrough for truck lovers. Alpine engineered their SWT-10S2 10" subwoofer to go behind your seat and sound especially good in the limited space of a truck cab. This deep-sounding, high-performance sub works well in shallow enclosures that'll fit behind or under the seat in your truck. A "high amplitude" surround allows more cone travel than a regular sub, so the SWT-10S2 can push more air and play louder. Airflow-insured subs get hot as they play, and the heat usually gets vented away via a port in the back of the sub's pole piece. Alpine recessed the pole port and added cooling air vents on the sides of the frame, allowing you to use an enclosure with an inside clearance of as little as 4-3/16" without blocking critical airflow. An SWT-10S4 will work well in a ported or sealed box so you can get your favorite bass tone, boomy or tight. The power takes for top performance, and you'll want to pick an amplifier that delivers between 300 and 500 watts RMS at 4 ohms. This single voice coil, the 4-ohm sub, will draw the maximum output power from a subwoofer amplifier when used along with a second SWT-10S2 in a system. If you're planning on running a pair, look for an amp that delivers between 600 and 1000 watts RMS at 2 ohms. General Features: 10" SWT Series Single 2-ohm Shallow Mount Truck Subwoofer Peak Power Handling: 1,000 watts RMS Power Handling: 350 watts Recommended Power Range: 100W - 350W Poly-Mica Dust Cap & Pulp-Kevlar Polyurethane Foam Surround H.A.M.R. Surround Technology Spiral Cut Aluminum Former 65mm Voice Coil with High-Temp 4-Layer SVC Winding 8AWG Push Terminals Top-mount depth: 4-3/16" Mounting Diameter: 8-15/16'' Frequency Response: 30 - 200 Hz Sensitivity: 84.8 dB Authorized Dealer 1-year Manufacturer's Warranty What is in the SWT-10S2 package: SWT-10S2 owner's manual 10" Thin-mount subwoofer Online product registration information Warranty information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.