Car Tweeters (106)

Rockford Fosgate Punch Pro PP4-NT Car Audio 100W Peak (50W RMS) 1.0" Single Punch Pro Series 4-Ohm High SPL Neodymium TweeterPut crisp, clear highs that even the most discerning audiophiles would approve of in your vehicle with the Rockford Fosgate Punch Pro 1 Inch 4 Ohm Neodymium Tweeter.This high-efficiency horn tweeter features an aluminum diaphragm, phase plug, and frame, along with a high-temperature 1-inch voice coil. It boasts an RMS power of 50 watts with 4 ohms of nominal impedance, as well as a neodymium motor structure.General Features: 1" Punch Pro Series Car Tweeter Power Handling: Peak: 100 watts RMS: 50 watts Recommended power range: 10 - 50 watts RMS CEA-2031 compliant High-efficiency horn tweeter Aluminum diaphragm Aluminum phase plug High temp Nomex former voice coil Die-cast aluminum frame All metal input spring terminal connection Neodymium motor structure Built-in 6dB/Octave crossover Removable mounting flange Mounting hardware included PP4-X and PP8-X crossover compatible 4 ohms impedance Sensitivity: 105dB Frequency response: 4,000 - 20,000 Hz Crossover: 4,000 Hz @ 6dB/Octave Tweeter Depth: 2.57" Authorized Internet Dealer 1-year Manufacturer's Warranty ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca

Rockford Fosgate Punch Pro PP4-NT Car Audio 100W Peak (50W RMS) 1.0" Single Punch Pro Series 4-Ohm High SPL Neodymium TweeterPut crisp, clear highs that even the most discerning audiophiles would approve of in your vehicle with the Rockford Fosgate Punch Pro 1 Inch 4 Ohm Neodymium Tweeter.This high-efficiency horn tweeter features an aluminum diaphragm, phase plug, and frame, along with a high-temperature 1-inch voice coil. It boasts an RMS power of 50 watts with 4 ohms of nominal impedance, as well as a neodymium motor structure.General Features: 1" Punch Pro Series Car Tweeter Power Handling: Peak: 100 watts RMS: 50 watts Recommended power range: 10 - 50 watts RMS CEA-2031 compliant High-efficiency horn tweeter Aluminum diaphragm Aluminum phase plug High temp Nomex former voice coil Die-cast aluminum frame All metal input spring terminal connection Neodymium motor structure Built-in 6dB/Octave crossover Removable mounting flange Mounting hardware included PP4-X and PP8-X crossover compatible 4 ohms impedance Sensitivity: 105dB Frequency response: 4,000 - 20,000 Hz Crossover: 4,000 Hz @ 6dB/Octave Tweeter Depth: 2.57" Authorized Internet Dealer 1-year Manufacturer's Warranty ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Rockford Fosgate PRIME R1T-S 160W Peak (80W RMS) 1" Mylar Balanced Dome Car Tweeters The R1T-S is a 1/2” mylar balanced dome tweeter kit rated at 40 watts RMS offering accurate reproduction of high frequencies. Kit includes integrated high-pass crossovers and flush, surface, and angle configurations. The PRIME series Component System kits are a new generation of factory replacement speakers delivering authentic Rockford Fosgate sound. The R1T-S is a dedicated tweeter system featuring a lightweight Mylar® dome for high sensitivity and smooth extended frequency response. This low distortion material allows accurate reproduction of high frequencies for an open sound stage. Multiple tweeter mounting configurations allow flush, surface, and angle configurations. General Features: Prime Series Tweeter Kit Power Handling: Peak: 160 watts per set / 80 watts each side Power Handling: RMS: 80 watts per set / 40 watts each side Recommended power range: 10 - 40 watts RMS per channel CEA-2031 Compliant speaker system Klippel verified speaker certified 1" Tweeter features a lightweight Mylar dome delivering crisp sound reproduction Low distortion material allows accurate reproduction of high frequencies for an open sound stage Tweeter High-Pass (HP): 4.5kHz @ 6dB/octave Frequency response: 2,500 - 22,000 Hz Free air resonance: 2,600 Hz Sensitivity: 72.5 dB Surface/angle and flush mount Contains mounting hardware Grilles/trim rings included Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the box: Rockford Fosgate R1T-S owner's manual Two 1" tweeters (with attached 6' speaker wire terminated by quick-slide connectors) 2 Flush-mounting brackets (installed) 2 Flush mount retaining rings 2 Surface mounting brackets Four 5/8" Flat head screws Installation and Operation Instructions (English/ French/ Spanish/ German/ Italian) ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca

Rockford Fosgate Prime R1T-S 1-Inch Tweeter Kit & Metra 72-4568 Speaker Harness for Selected General Motor VehiclesMetra 72-4568 Speaker Harness for Selected General Motor VehiclesSpeaker Harness for Select GM Vehicles Rockford Fosgate PRIME R1T-S 160W Peak (80W RMS) 1" Mylar Balanced Dome Car Tweeters The R1T-S is a 1/2” mylar balanced dome tweeter kit rated at 40 watts RMS offering accurate reproduction of high frequencies. Kit includes integrated high-pass crossovers and flush, surface, and angle configurations. The PRIME series Component System kits are a new generation of factory replacement speakers delivering authentic Rockford Fosgate sound. The R1T-S is a dedicated tweeter system featuring a lightweight Mylar® dome for high sensitivity and smooth extended frequency response. This low distortion material allows accurate reproduction of high frequencies for an open sound stage. Multiple tweeter mounting configurations allow flush, surface, and angle configurations. General Features: Prime Series Tweeter Kit Power Handling: Peak: 160 watts per set / 80 watts each side Power Handling: RMS: 80 watts per set / 40 watts each side Recommended power range: 10 - 40 watts RMS per channel CEA-2031 Compliant speaker system Klippel verified speaker certified 1" Tweeter features a lightweight Mylar dome delivering crisp sound reproduction Low distortion material allows accurate reproduction of high frequencies for an open sound stage Tweeter High-Pass (HP): 4.5kHz @ 6dB/octave Frequency response: 2,500 - 22,000 Hz Free air resonance: 2,600 Hz Sensitivity: 72.5 dB Surface/angle and flush mount Contains mounting hardware Grilles/trim rings included Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the box: Rockford Fosgate R1T-S owner's manual Two 1" tweeters (with attached 6' speaker wire terminated by quick-slide connectors) 2 Flush-mounting brackets (installed) 2 Flush mount retaining rings 2 Surface mounting brackets Four 5/8" Flat head screws Installation and Operation Instructions (English/ French/ Spanish/ German/ Italian) ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca

Rockford Fosgate Punch P1T-S 240W Peak (120W RMS) 1" Punch Series Car Tweeters Kit The Punch P1T-S is a 1” PEI dome tweeter kit designed for natural sound reproduction rated at 60 Watts RMS. The kit includes high-pass crossovers, mounting hardware, and three bezels for flush, surface, and angle configurations. Car audio fanatics will love the Punch series tweeter kit. It features a 1" (25mm) PEI dome, cool-looking outboard crossover, and 3 mounting bezels to accommodate various installations. General Features: 1" Punch Series Tweeter Kit Power Handling: Peak: 240 watts per pair / 120 watts each RMS: 120 watts per pair / 60 watts each Recommended power range: 10 - 60 watts RMS per channel Butyl rubber surround PEI dome tweeter Recessed tweeter mount uses standard 1-3/4" hole saw DDC (Discreet Dual Clamp) Tweeter Mounting provides concentric clamping pressure around the perimeter of the mounting hole. This results in maximum ease of installation. Grilles and mounting hardware included High Pass: 3,500 Hz 12dB/octave Butterworth Sensitivity: 90dB Frequency Response: 3,500-22,000 Hz Mounting Depth: 1/2" Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the box: Rockford Fosgate Punch P1T-S owner's manual Two 1" tweeters (with attached 6" speaker wire terminated with female quick-slide connectors) 2 Crossovers 2 Front flush mount brackets 2 Rear flush mount brackets 2 Surface mounting housings 2 Trim rings Two M4x25mm Machine screws Two M4x10mm Machine screws Two M4x16mm Stud bolts Two 40" Lengths of speaker wire (each with male quick slides on one end and female quick slides on the other) Two 40" Lengths of speaker wire (each with female quick slides on one end and bare wire on the other) Four 7" Zip ties Installation/Operation Instructions (English/ French/ Spanish/ German/ Italian) ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca

2 Pair Rockford Fosgate Punch P1T-S 240W Peak (120W RMS) 1" Punch Series Car Tweeters Kit The Punch P1T-S is a 1” PEI dome tweeter kit for natural sound reproduction rated at 60 Watts RMS. The kit includes high-pass crossovers, mounting hardware, and three bezels for flush, surface, and angle configurations. Car audio fanatics will love the Punch series tweeter kit. It features a 1" (25mm) PEI dome, a cool-looking outboard crossover, and three mounting bezels to accommodate various installations. General Features: 1" Punch Series Tweeter Kit Power Handling: Peak: 240 watts per pair / 120 watts each RMS: 120 watts per pair / 60 watts each Recommended power range: 10 - 60 watts RMS per channel Butyl rubber surround PEI dome tweeter The recessed tweeter mount uses a standard 1-3/4" hole saw DDC (Discreet Dual Clamp) Tweeter Mounting provides concentric clamping pressure around the perimeter of the mounting hole. This results in maximum ease of installation. Grilles and mounting hardware included High Pass: 3,500 Hz 12dB/octave Butterworth Sensitivity: 90dB Frequency Response: 3,500-22,000 Hz Mounting Depth: 1/2" Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the box: Rockford Fosgate Punch P1T-S owner's manual Two 1" tweeters (with attached 6" speaker wire terminated with female quick-slide connectors) 2 Crossovers 2 Front flush mount brackets 2 Rear flush mount brackets 2 Surface mounting housings 2 Trim rings Two M4x25mm Machine screws Two M4x10mm Machine screws Two M4x16mm Stud bolts Two 40" Lengths of speaker wire (each with male quick slides on one end and female quick slides on the other) Two 40" Lengths of speaker wire (each with female quick slides on one end and bare wire on the other) Four 7" Zip ties Installation/Operation Instructions (English/ French/ Spanish/ German/ Italian) ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca

2 Pair Rockford Fosgate Punch P1T-S 240W Peak (120W RMS) 1" Punch Series Car Tweeters Kit The Punch P1T-S is a 1” PEI dome tweeter kit designed for natural sound reproduction rated at 60 Watts RMS. The kit includes high-pass crossovers, mounting hardware, and three bezels for flush, surface, and angle configurations. Car audio fanatics will love the Punch series tweeter kit. It features a 1" (25mm) PEI dome, cool-looking outboard crossover, and 3 mounting bezels to accommodate various installations. General Features: 1" Punch Series Tweeter Kit Power Handling: Peak: 240 watts per pair / 120 watts each RMS: 120 watts per pair / 60 watts each Recommended power range: 10 - 60 watts RMS per channel Butyl rubber surround PEI dome tweeter Recessed tweeter mount uses standard 1-3/4" hole saw DDC (Discreet Dual Clamp) Tweeter Mounting provides concentric clamping pressure around the perimeter of the mounting hole. This results in maximum ease of installation. Grilles and mounting hardware included High Pass: 3,500 Hz 12dB/octave Butterworth Sensitivity: 90dB Frequency Response: 3,500-22,000 Hz Mounting Depth: 1/2" Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the box: Rockford Fosgate Punch P1T-S owner's manual Two 1" tweeters (with attached 6" speaker wire terminated with female quick-slide connectors) 2 Crossovers 2 Front flush mount brackets 2 Rear flush mount brackets 2 Surface mounting housings 2 Trim rings Two M4x25mm Machine screws Two M4x10mm Machine screws Two M4x16mm Stud bolts Two 40" Lengths of speaker wire (each with male quick slides on one end and female quick slides on the other) Two 40" Lengths of speaker wire (each with female quick slides on one end and bare wire on the other) Four 7" Zip ties Installation/Operation Instructions (English/ French/ Spanish/ German/ Italian) ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

2 Pair Rockford Fosgate Punch P1T-S 240W Peak (120W RMS) 1" Punch Series Car Tweeters Kit The Punch P1T-S is a 1” PEI dome tweeter kit designed for natural sound reproduction rated at 60 Watts RMS. The kit includes high-pass crossovers, mounting hardware, and three bezels for flush, surface, and angle configurations. Car audio fanatics will love the Punch series tweeter kit. It features a 1" (25mm) PEI dome, cool-looking outboard crossover, and 3 mounting bezels to accommodate various installations. General Features: 1" Punch Series Tweeter Kit Power Handling: Peak: 240 watts per pair / 120 watts each RMS: 120 watts per pair / 60 watts each Recommended power range: 10 - 60 watts RMS per channel Butyl rubber surround PEI dome tweeter Recessed tweeter mount uses standard 1-3/4" hole saw DDC (Discreet Dual Clamp) Tweeter Mounting provides concentric clamping pressure around the perimeter of the mounting hole. This results in maximum ease of installation. Grilles and mounting hardware included High Pass: 3,500 Hz 12dB/octave Butterworth Sensitivity: 90dB Frequency Response: 3,500-22,000 Hz Mounting Depth: 1/2" Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the box: Rockford Fosgate Punch P1T-S owner's manual Two 1" tweeters (with attached 6" speaker wire terminated with female quick-slide connectors) 2 Crossovers 2 Front flush mount brackets 2 Rear flush mount brackets 2 Surface mounting housings 2 Trim rings Two M4x25mm Machine screws Two M4x10mm Machine screws Two M4x16mm Stud bolts Two 40" Lengths of speaker wire (each with male quick slides on one end and female quick slides on the other) Two 40" Lengths of speaker wire (each with female quick slides on one end and bare wire on the other) Four 7" Zip ties ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca

6 Pair Rockford Fosgate Punch P1T-S 240W Peak (120W RMS) 1" Punch Series Car Tweeters Kit The Punch P1T-S is a 1” PEI dome tweeter kit designed for natural sound reproduction rated at 60 Watts RMS. The kit includes high-pass crossovers, mounting hardware, and three bezels for flush, surface, and angle configurations. Car audio fanatics will love the Punch series tweeter kit. It features a 1" (25mm) PEI dome, cool-looking outboard crossover, and 3 mounting bezels to accommodate various installations. General Features: 1" Punch Series Tweeter Kit Power Handling: Peak: 240 watts per pair / 120 watts each RMS: 120 watts per pair / 60 watts each Recommended power range: 10 - 60 watts RMS per channel Butyl rubber surround PEI dome tweeter Recessed tweeter mount uses standard 1-3/4" hole saw DDC (Discreet Dual Clamp) Tweeter Mounting provides concentric clamping pressure around the perimeter of the mounting hole. This results in maximum ease of installation. Grilles and mounting hardware included High Pass: 3,500 Hz 12dB/octave Butterworth Sensitivity: 90dB Frequency Response: 3,500-22,000 Hz Mounting Depth: 1/2" Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the box: Rockford Fosgate Punch P1T-S owner's manual Two 1" tweeters (with attached 6" speaker wire terminated with female quick-slide connectors) 2 Crossovers 2 Front flush mount brackets 2 Rear flush mount brackets 2 Surface mounting housings 2 Trim rings Two M4x25mm Machine screws Two M4x10mm Machine screws Two M4x16mm Stud bolts Two 40" Lengths of speaker wire (each with male quick slides on one end and female quick slides on the other) Two 40" Lengths of speaker wire (each with female quick slides on one end and bare wire on the other) Four 7" Zip ties Installation/Operation Instructions (English/ French/ Spanish/ German/ Italian) ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca

6 Pair Rockford Fosgate Punch P1T-S 240W Peak (120W RMS) 1" Punch Series Car Tweeters Kit The Punch P1T-S is a 1” PEI dome tweeter kit designed for natural sound reproduction rated at 60 Watts RMS. The kit includes high-pass crossovers, mounting hardware, and three bezels for flush, surface, and angle configurations. Car audio fanatics will love the Punch series tweeter kit. It features a 1" (25mm) PEI dome, cool-looking outboard crossover, and 3 mounting bezels to accommodate various installations. General Features: 1" Punch Series Tweeter Kit Power Handling: Peak: 240 watts per pair / 120 watts each RMS: 120 watts per pair / 60 watts each Recommended power range: 10 - 60 watts RMS per channel Butyl rubber surround PEI dome tweeter Recessed tweeter mount uses standard 1-3/4" hole saw DDC (Discreet Dual Clamp) Tweeter Mounting provides concentric clamping pressure around the perimeter of the mounting hole. This results in maximum ease of installation. Grilles and mounting hardware included High Pass: 3,500 Hz 12dB/octave Butterworth Sensitivity: 90dB Frequency Response: 3,500-22,000 Hz Mounting Depth: 1/2" Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the box: Rockford Fosgate Punch P1T-S owner's manual Two 1" tweeters (with attached 6" speaker wire terminated with female quick-slide connectors) 2 Crossovers 2 Front flush mount brackets 2 Rear flush mount brackets 2 Surface mounting housings 2 Trim rings Two M4x25mm Machine screws Two M4x10mm Machine screws Two M4x16mm Stud bolts Two 40" Lengths of speaker wire (each with male quick slides on one end and female quick slides on the other) Two 40" Lengths of speaker wire (each with female quick slides on one end and bare wire on the other) Four 7" Zip ties ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca

Rockford Fosgate PRIME R1T-S 160W Peak (80W RMS) 1" Mylar Balanced Dome Car Tweeters The R1T-S is a 1/2” mylar balanced dome tweeter kit rated at 40 watts RMS offering accurate reproduction of high frequencies. Kit includes integrated high-pass crossovers and flush, surface, and angle configurations. The PRIME series Component System kits are a new generation of factory replacement speakers delivering authentic Rockford Fosgate sound. The R1T-S is a dedicated tweeter system featuring a lightweight Mylar® dome for high sensitivity and smooth extended frequency response. This low distortion material allows accurate reproduction of high frequencies for an open sound stage. Multiple tweeter mounting configurations allow flush, surface, and angle configurations. General Features: Prime Series Tweeter Kit Power Handling: Peak: 160 watts per set / 80 watts each side Power Handling: RMS: 80 watts per set / 40 watts each side Recommended power range: 10 - 40 watts RMS per channel CEA-2031 Compliant speaker system Klippel verified speaker certified 1" Tweeter features a lightweight Mylar dome delivering crisp sound reproduction Low distortion material allows accurate reproduction of high frequencies for an open sound stage Tweeter High-Pass (HP): 4.5kHz @ 6dB/octave Frequency response: 2,500 - 22,000 Hz Free air resonance: 2,600 Hz Sensitivity: 72.5 dB Surface/angle and flush mount Contains mounting hardware Grilles/trim rings included Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the box: Rockford Fosgate R1T-S owner's manual Two 1" tweeters (with attached 6' speaker wire terminated by quick-slide connectors) 2 Flush-mounting brackets (installed) 2 Flush mount retaining rings 2 Surface mounting brackets Four 5/8" Flat head screws Installation and Operation Instructions (English/ French/ Spanish/ German/ Italian) ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca

Rockford Fosgate PRIME R1T-S 160W Peak (80W RMS) 1" Mylar Balanced Dome Car Tweeters The R1T-S is a 1/2” mylar balanced dome tweeter kit rated at 40 watts RMS offering accurate reproduction of high frequencies. Kit includes integrated high-pass crossovers and flush, surface, and angle configurations. The PRIME series Component System kits are a new generation of factory replacement speakers delivering authentic Rockford Fosgate sound. The R1T-S is a dedicated tweeter system featuring a lightweight Mylar® dome for high sensitivity and smooth extended frequency response. This low distortion material allows accurate reproduction of high frequencies for an open sound stage. Multiple tweeter mounting configurations allow flush, surface, and angle configurations. General Features: Prime Series Tweeter Kit Power Handling: Peak: 160 watts per set / 80 watts each side Power Handling: RMS: 80 watts per set / 40 watts each side Recommended power range: 10 - 40 watts RMS per channel CEA-2031 Compliant speaker system Klippel verified speaker certified 1" Tweeter features a lightweight Mylar dome delivering crisp sound reproduction Low distortion material allows accurate reproduction of high frequencies for an open sound stage Tweeter High-Pass (HP): 4.5kHz @ 6dB/octave Frequency response: 2,500 - 22,000 Hz Free air resonance: 2,600 Hz Sensitivity: 72.5 dB Surface/angle and flush mount Contains mounting hardware Grilles/trim rings included Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the box: Rockford Fosgate R1T-S owner's manual Two 1" tweeters (with attached 6' speaker wire terminated by quick-slide connectors) 2 Flush-mounting brackets (installed) 2 Flush mount retaining rings 2 Surface mounting brackets Four 5/8" Flat head screws ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca