Car Equalizers (82)

Audio Control AudioControl 4 pin plug LC8i EQL Epic160 LCQ-1 LC2i EQS These 4-pin connectors are used on our car and home products. If you’ve lost your connector, or if you like to collect small, interesting objects, you’ve found the right page. Check your product to see which connector you need, either 4-pin, then add as many as you like to your cart. Postage is included when shipping within the Contiguous United States. 4 Pin, 4-pin power plug (Black) for Audio Control, Audiocontrol, 4 Pin Plug LC8 EQL EQS EPIC160 LC2I LCQ1 THREE.1 FOUR.1 DQL8 Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Audio Control AudioControl 4 pin plug LC8i EQL Epic160 LCQ-1 LC2i EQS These 4-pin connectors are used on our car and home products. If you’ve lost your connector, or if you like to collect small, interesting objects, you’ve found the right page. Check your product to see which connector you need, either 4-pin, then add as many as you like to your cart. Postage is included when shipping within the Contiguous United States. 4 Pin, 4-pin power plug (Black) for Audio Control, Audiocontrol, 4 Pin Plug LC8 EQL EQS EPIC160 LC2I LCQ1 THREE.1 FOUR.1 DQL8 Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Audio Control LC2i Pro 2 Channel Line Out Converter with ACCUBASS w/ Dash Remote General Features: Adjustable 2-channel line out converter Separate level adjustment for each channel Two channels of active speaker level inputs (up to 40V input handling) AccuBASS® processing for correction of bass roll-off ACR-1 dash remote included Load Selection Switch Ground Isolation Switch 400-watt maximum input AccuBASS circuitry restores the bass signal Total Harmonic Distortion: 0.01% Signal to Noise: >110 dB Frequency Response: 20 Hz – 50 kHz ±1 dB Dimensions: 6.9″L x 3″D x 1″H (including speaker connectors) Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the box: AudioControl LC2i PRO owner's manual Two-Channel line output converter Two 4-pin captive-screw connectors (installed) ACR-1 Level control 16.5' Level-control cable (RJ-14) Quickstart guide (on cardboard label) ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Audio Control LC6i 6 Channel Line Out Converter with Internal Summing for add aftermarket amps to a factory system & ACR-1 Dash Remote AudioControl continues to simplify OEM integration with the new LC6i Six Channel Line Output Converter with internal summing. The LC6i is built on the same technology as its predecessor, the LC6. The LC6i converts speaker-level inputs from a factory radio or factory amplifier into high-quality pre-amp signals. The addition of internal summing capabilities and improved GTO™ signal-sense turn-on make the LC6i the perfect way to solve your OEM headaches. The LC6i allows for the addition of aftermarket processors and amplifiers while maintaining the use of the factory volume and steering wheel controls. Internal signal summing and AudioControl’s new GTO™ signal-sense turn-on make the LC6i a perfect OEM interface for a performance audio system. The LC6i follows in the steps of the rampantly successful LC8 Eight Channel Line Output Converter, offering all the same features for 6 channel systems at a reduced price. The LC6i accepts speaker level signals, both crossed-over, and full range, and converts them to high-quality pre-amp signals. Signals from factory radios with built-in crossovers can be overcome by summing them together, internally, to provide a full-range preamp signal. The LC6i provides the type of clean pre-amp signals installers are familiar with. Those who desire custom control over the sound can easily add one of AudioControl’s many crossovers or equalizers which offer unlimited system design flexibility, clearly different than traditional OEM interfaces. Add remote level control for your AudioControl processor or amplifier. This is the replacement remote for the Epicenter. Comes with a 20-foot cable and removable mounting enclosure (for custom dash installations).s. General Features: Six Input and Output Channels 6 Speaker Level Inputs - Can Accept 400-Watt Signals! Signal sensing inputs Internal Channel Summing AutoMode inputs Level matching controls 12-volt trigger output Line Output Converter: A device for converting a powered (or amplified) signal into a pre-amp line level (or non-powered) signal Input for optional subwoofer level control: AudioControl ACR-1 Color: Black Weight: 3.5 lbs Size: 8.00" W x 6.00" D x 1.20" H Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) LC6i Specifications: Maximum speaker-level input: 400 watts @ 4 ohms Maximum output level: 9.5Vrms Output gain: +/-12 dB Frequency response: 10Hz-22kHz Total harmonic distortion: 0.01% Input Impedance: 20K Ohms Power supply: High headroom PWM switching Power draw: 200mA Recommended fuse rating: 1 Amp Remote Trigger Output Current: 1 Amp What is in the LC6i box: 6-Channel line-output converter Instructions/Specs/Warranty (on packaging) Quality Control Certificate AudioControl LC6i owner's manual AudioControl Remote ACR-1 Dash Mount Wired Remote Level Control for Select AudioControl Sound Processors Add remote level control for your AudioControl processor or amplifier. This is the replacement remote for the Epicenter. Comes with a 20-foot cable and removable mounting enclosure (for custom dash installations).s. General Features Wired Remote Level Control Mounts on dash using built-in bracket Detachable mounting plate Works with select AudioControl sound processors Direct replacement remote for the Epicenter Includes 20' power cable Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) compatible with 6XS ACM-1.300 The Epicenter® Concert Series LC2i LC6i LC7i Overdrive Plus Matrix Plus LC-4.800 LC-6.1200 legacy products supported LC6 LC8 Original Epicenter® (bypass not supported) What is in the ACR-1 box: Remote dash mount control 20' RJ-14 cable. Mounting Instructions on packaging AudioControl ACR-1 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Audio Control LC7i 6 Channel Line Out Converter with bass restoration adds aftermarket subs and amps to a factory system & ACR-1 Dash Remote The AudioControl LC7i, six channel active line converter, allows all music lovers, who want a great in-car audio experience, to keep their factory-installed source unit and dramatically improve their system performance. The LC7i delivers amazing sound quality and fixes one of the biggest letdowns of today’s factory systems, weak BASS! Designed for maximum sound quality and enhanced audio performance, the LC7i incorporates AccuBASS™. This patented process automatically corrects for the bass roll-off that is common with many factory-installed audio systems and AudioControl’s unique and exclusive AccuBASS™ circuitry maintains and restores the Bass as the volume is turned up, improving the audio performance. The LC7i allows the flexibility of powering the audio signals downstream to single or multiple factory amps maximizing sound quality & achieving high output at a great price. In addition, the LC7i is designed to fit into a compact chassis allowing an easy & flexible factory system upgrade in today’s space constrained vehicles. The ACR-1 dash remote (sold separately) allows the user to control the level of the low-frequency output. Add remote level control for your AudioControl processor or amplifier. This is the replacement remote for the Epicenter. Comes with a 20-foot cable and removable mounting enclosure (for custom dash installations).s. General Features: Six Input and Output Channels 6 Speaker Level Inputs - Can Accept 400-Watt Signals! Signal sensing inputs GTO (Great Turn-On) Circuit Internal Channel Summing AutoMode inputs Level matching controls 12-volt trigger output Line Output Converter: A device for converting a powered (or amplified) signal into a pre-amp line level (or non-powered) signal Input for optional subwoofer level control: AudioControl ACR-1 Color: Black Weight: 3.0 lbs Size: 7.5" W x 4.72" D x 1.22" H Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) LC7i Specifications: Maximum speaker-level input: 400 watts @ 4 ohms Maximum output level: 8.5Vrms Output gain: ±15 dB Frequency response: 10Hz - 22,000 Hz Total harmonic distortion: 0.01% Input Impedance: 20 Kohms Output Impedance: 150 ohms Power supply: High headroom PWM switching Power draw: 350mA Recommended fuse rating: 2 Amp Remote Trigger Output Current: 1 Amp What is in the LC7i box: 6-Channel line-output converter Instructions/Specs/Warranty (on packaging) Quality Control Certificate AudioControl LC7i owner's manual AudioControl Remote ACR-1 Dash Mount Wired Remote Level Control for Select AudioControl Sound Processors Add remote level control for your AudioControl processor or amplifier. This is the replacement remote for the Epicenter. Comes with a 20-foot cable and removable mounting enclosure (for custom dash installations).s. General Features Wired Remote Level Control Mounts on the dash using built-in bracket Detachable mounting plate Works with select AudioControl sound processors Direct replacement remote for the Epicenter Includes 20' power cable Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) compatible with 6XS ACM-1.300 The Epicenter® Concert Series LC2i LC6i LC7i Overdrive Plus Matrix Plus LC-4.800 LC-6.1200 legacy products supported LC6 LC8 Original Epicenter® (bypass not supported) What is in the ACR-1 box: Remote dash mount control 20' RJ-14 cable. Mounting Instructions on packaging AudioControl ACR-1 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Audio Control LC6i 6 Channel Line Out Converter with Internal Summing for adding aftermarket amps to a factory system AudioControl continues to simplify OEM integration with the new LC6i Six Channel Line Output Converter with internal summing. The LC6i is built on the same technology as its predecessor, the LC6. The LC6i converts speaker-level inputs from a factory radio or factory amplifier into high-quality pre-amp signals. The addition of internal summing capabilities and improved GTO™ signal-sense turn-on make the LC6i the perfect way to solve your OEM headaches. The LC6i allows for the addition of aftermarket processors and amplifiers while maintaining the use of the factory volume and steering wheel controls. Internal signal summing and AudioControl’s new GTO™ signal-sense turn-on make the LC6i a perfect OEM interface for a performance audio system. The LC6i follows in the steps of the rampantly successful LC8 Eight Channel Line Output Converter, offering all the same features for 6 channel systems at a reduced price. The LC6i accepts speaker level signals, both crossed-over, and full range, and converts them to high-quality pre-amp signals. Signals from factory radios with built-in crossovers can be overcome by summing them together, internally, to provide a full-range preamp signal. The LC6i provides the type of clean pre-amp signals installers are familiar with. Those who desire custom control over the sound can easily add one of AudioControl’s many crossovers or equalizers which offer unlimited system design flexibility, clearly different than traditional OEM interfaces. General Features: Six Input and Output Channels 6 Speaker Level Inputs - Can Accept 400-Watt Signals! Signal sensing inputs Internal Channel Summing AutoMode inputs Level matching controls 12-volt trigger output Line Output Converter: A device for converting a powered (or amplified) signal into a pre-amp line level (or non-powered) signal Input for optional subwoofer level control: AudioControl ACR-1 Color: Black Weight: 3.5 lbs Size: 8.00" W x 6.00" D x 1.20" H Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) LC6i Specifications: Maximum speaker-level input: 400 watts @ 4 ohms Maximum output level: 9.5Vrms Output gain: +/-12 dB Frequency response: 10Hz-22kHz Total harmonic distortion: 0.01% Input Impedance: 20K Ohms Power supply: High headroom PWM switching Power draw: 200mA Recommended fuse rating: 1 Amp Remote Trigger Output Current: 1 Amp What is in the LC6i box: 6-Channel line-output converter Instructions/Specs/Warranty (on packaging) Quality Control Certificate AudioControl LC6i owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Audio Control LC6i 6 Channel Line Out Converter with Internal Summing for adding aftermarket amps to a factory system & ACR-1 Dash Remote AudioControl continues to simplify OEM integration with the new LC6i Six Channel Line Output Converter with internal summing. The LC6i is built on the same technology as its predecessor, the LC6. The LC6i converts speaker-level inputs from a factory radio or factory amplifier into high-quality pre-amp signals. The addition of internal summing capabilities and improved GTO™ signal-sense turn-on make the LC6i the perfect way to solve your OEM headaches. The LC6i allows for the addition of aftermarket processors and amplifiers while maintaining the use of the factory volume and steering wheel controls. Internal signal summing and AudioControl’s new GTO™ signal-sense turn-on make the LC6i a perfect OEM interface for a performance audio system. The LC6i follows in the steps of the rampantly successful LC8 Eight Channel Line Output Converter, offering all the same features for 6 channel systems at a reduced price. The LC6i accepts speaker level signals, both crossed-over, and full range, and converts them to high-quality pre-amp signals. Signals from factory radios with built-in crossovers can be overcome by summing them together, internally, to provide a full-range preamp signal. The LC6i provides the type of clean pre-amp signals installers are familiar with. Those who desire custom control over the sound can easily add one of AudioControl’s many crossovers or equalizers which offer unlimited system design flexibility, clearly different than traditional OEM interfaces. General Features: Six Input and Output Channels 6 Speaker Level Inputs - Can Accept 400-Watt Signals! Signal sensing inputs Internal Channel Summing AutoMode inputs Level matching controls 12-volt trigger output Line Output Converter: A device for converting a powered (or amplified) signal into a pre-amp line level (or non-powered) signal Input for optional subwoofer level control: AudioControl ACR-1 Color: Black Weight: 3.5 lbs Size: 8.00" W x 6.00" D x 1.20" H Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) LC6i Specifications: Maximum speaker-level input: 400 watts @ 4 ohms Maximum output level: 9.5Vrms Output gain: +/-12 dB Frequency response: 10Hz-22kHz Total harmonic distortion: 0.01% Input Impedance: 20K Ohms Power supply: High headroom PWM switching Power draw: 200mA Recommended fuse rating: 1 Amp Remote Trigger Output Current: 1 Amp What is in the LC6i package: 6-Channel line-output converter Instructions/Specs/Warranty (on packaging) Quality Control Certificate LC6i owner's manual AudioControl Remote ACR-1 Dash Mount Wired Remote Level Control for Select AudioControl Sound Processors General Features Wired Remote Level Control Mounts on the dash using built-in bracket Detachable mounting plate Works with select AudioControl sound processors Direct replacement remote for the Epicenter Includes 20' power cable Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) What is in the ACR-1 package: Remote dash mount control 20' RJ-14 cable. Mounting Instructions on packaging ACR-1 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine PXE-0850X 8-channel car amplifier with digital signal processing 25 watts RMS x 8 As more and more newer vehicles are equipped with highly integrated displays and complex sound systems, the stand-alone DSP, Digital Signal Processor, is becoming crucial for building the next-level Alpine sound system. How do you upgrade your sound without changing your head unit? It may be more complex than adding amplifiers anymore. Modern factory systems generally have speakers playing a specific range of frequencies, making it difficult to improve sound and add aftermarket amplifiers. The Alpine PXE-0850S allows you to take up to 6 independent signals (3 per side, for example) and combine them to create a full range signal. Once you have that full range signal, you can send them to up to 12 independent channels allowing for extreme versatility in system building. The PXE-0850S has an LCD remote controller that can be flush-mounted on the dash. Use the rotary knob to quickly control volume, preset storage and recall, and source selection. You can also view the results on the remote controller’s LED screen. If needed, the controller adds quick adjustability to your system, or it can be left out altogether if smartphone control is enough. General Features: Music & navigation sound mixing Can arbitrarily adjust the volume ratio of main/sub audio source Full-frequency mode is added, and each channel can be set to full-frequency mode, which solves the problem that channels cannot be distributed in projects such as audition rooms and RVs to reduce the setting time. Split-screen display, adding delay group, more convenient operation! Total volume adjustment Bass volume adjustment Sound source switching Auxiliary sound source switching EQ preset switching Frequency response: 20Hz - 20KHz Inputs: 6 high-level signal inputs, 6-channel RCA signal, Bluetooth signal input Outputs: 8 x 25W (Rated power), 12-channel RCA output 2.0 multichannel surround 31 Bands parametric EQ Hi-pass / Low-pass / Bandpass Crossover Time delays up to 20 MS per channel Input/output frequency summing Music & navigation sound mixing Authorized Internet Dealer 1-year Manufacturer's Warranty ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine PXE-0850X 8-channel car amplifier with digital signal processing 25 watts RMS x 8 As more and more newer vehicles are equipped with highly integrated displays and complex sound systems, the stand-alone DSP, Digital Signal Processor, is becoming crucial for building the next-level Alpine sound system. How do you upgrade your sound without changing your head unit? It may be more complex than adding amplifiers anymore. Modern factory systems generally have speakers playing a specific range of frequencies, making it difficult to improve sound and add aftermarket amplifiers. The Alpine PXE-0850S allows you to take up to 6 independent signals (3 per side, for example) and combine them to create a full range signal. Once you have that full-range signal, you can send them to up to 12 independent channels allowing for extreme versatility in system building. The PXE-0850S has an LCD remote controller that can be flush-mounted on the dash. Use the rotary knob to quickly control volume, preset storage and recall, and source selection. You can also view the results on the remote controller’s LED screen. The controller adds quick adjustability to your system if needed, or it can be left out altogether if smartphone control is enough. General Features: Music & navigation sound mixing Can arbitrarily adjust the volume ratio of main/sub audio source Full-frequency mode is added, and each channel can be set to full-frequency mode, which solves the problem that channels cannot be distributed in projects such as audition rooms and RVs to reduce the setting time. Split-screen display, adding delay group, more convenient operation! Total volume adjustment Bass volume adjustment Sound source switching Auxiliary sound source switching EQ preset switching Frequency response: 20Hz - 20KHz Inputs: 6 high-level signal inputs, 6-channel RCA signal, Bluetooth signal input Outputs: 8 x 25W (Rated power), 12-channel RCA output 2.0 multichannel surround 31 Bands parametric EQ Hi-pass / Low-pass / Bandpass Crossover Time delays of up to 20 MS per channel Input/output frequency summing Music & navigation sound mixing Authorized Internet Dealer 1-year Manufacturer's Warranty ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.