Car Audio & Video Packages & Bundles (802)

Rockford Fosgate R2-300X4 Prime Series 300 Watts 4-Channel Class D Amplifier + Absolute KIT4 4G Amp Kit Primed for performance, the R2-300X4 is a 300-watt, full-range Class-D amplifier capable of operating at 4Ω or 2Ω stereo and 4Ω bridged/mono. This amplifier is extremely efficient because of its Class-D technology, which reduces the vehicle's electrical system demand. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. supply that generates more power as voltage increases. General Features: Rockford Fosgate Prime R2-300X4 Class-D Full-Range 4-Channel Amplifier 50 watts RMS x 4 at 4 ohms 75 watts RMS x 4 at 2 ohms 150 watts RMS x 2 bridged output at 4 ohms bridged mode Total power output: 3000 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeat able Auto Turn-On Circuit Features C.L.E.A.N. Set-up 2/4 Channel Input Selection Switch Front and Rear Variable Input Gain adjustment level Continuously Variable on-Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Full Range Class D Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers 1 Year Warranty Low level: 125mV-5V High level: 250mV-10V Frequency Response: 20 Hz - 20 kHz Hz Total Harmonic Distortion (THD): <1% Variable high-pass filter: 50 - 250 Hz, 24 dB/octave Variable low-pass filter: 50 - 250 Hz, 24 dB/octave Recommended Fuse Rating: 60A Dimensions: 1.9" x "6.8" x "10.1" Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the R2-300X4 package: R2-300X4 Owner's Manual 4-Channel amplifier Two 7" Speaker input harnesses 3mm Allen Hex key Four 3/4" Screws 4 Flat washers Installation and Operation Instructions Certificate of Performance Rockford Fosgate contact information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate R2-300X4 Prime Series 300 Watts 4-Channel Class D Amplifier + Absolute KIT0 0 Gauge Amp Kit Rockford Fosgate R2-300X4 Prime Series 300 Watts 4-Channel Class D Amplifier Primed for performance, the R2-300X4 is a 300-watt, full-range Class-D amplifier capable of operating at 4Ω or 2Ω stereo and 4Ω bridged/mono. This amplifier is extremely efficient because of its Class-D technology, which reduces the vehicle's electrical system demand. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. supply that generates more power as voltage increases. General Features: Rockford Fosgate Prime R2-300X4 Class-D Full-Range 4-Channel Amplifier 50 watts RMS x 4 at 4 ohms 75 watts RMS x 4 at 2 ohms 150 watts RMS x 2 bridged output at 4 ohms bridged mode Total power output: 3000 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeat able Auto Turn-On Circuit Features C.L.E.A.N. Set-up 2/4 Channel Input Selection Switch Front and Rear Variable Input Gain adjustment level Continuously Variable on-Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Full Range Class D Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers 1 Year Warranty Low level: 125mV-5V High level: 250mV-10V Frequency Response: 20 Hz - 20 kHz Hz Total Harmonic Distortion (THD): <1% Variable high-pass filter: 50 - 250 Hz, 24 dB/octave Variable low-pass filter: 50 - 250 Hz, 24 dB/octave Recommended Fuse Rating: 60A Dimensions: 1.9" x "6.8" x "10.1" Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the R2-300X4 package: R2-300X4 Owner's Manual 4-Channel amplifier Two 7" Speaker input harnesses 3mm Allen Hex key Four 3/4" Screws 4 Flat washers Installation and Operation Instructions Certificate of Performance Rockford Fosgate contact information Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

2 Pair Alpine S2-S65 6.5" 480 Watt Car Audio Speakers+BBX-F1200 4 Channel Amplifier + Absolute KIT4 4G Amp Kit Alpine S2-S65 120W 6.5" 2-Way Type-E Coaxial Car Speakers w/ Silk Tweeters Hearing is BelievingStep up your factory speakers to an affordable upgrade with the all-new Alpine Type-E speakers for the performance-packed sound quality you expect from Alpine.Quality over QuantityJust because you want better sound in your car doesn’t mean you have to break your budget. The Type-E speakers are the perfect, affordable option if you need replacement speakers or want to start building a sound system.Soft Dome Tweeter TechnologyTo output quality sound, the Type-E speakers are developed using soft dome tweeters rather than traditional cone-type tweeters, which can be harsh. This results in a more enjoyable listening experience in the car when playing back music or other entertainment over your sound system.General Features: 6-1/2" S Series 2-way Coaxial Car Speakers Peak Power Handling: 480 watts per pair / 240 watts each RMS Power Handling: 160 watts per pair / 80 watts each Hi-Res Audio-certified Polypropylene, Glass Fiber, and Mica cone material High-Amplitude Multi-Roll (HAMR) speaker surround 1" Cloth Dome tweeters voice coil Ferrite magnet motor structure Top-mount Depth: 2-5/16" Cutout Dimensions: 5-1/8" Impedance: 4 ohms Frequency Response: 70 - 40,000 Hz Sensitivity: 88 dB Speaker grilles are optional and sold separately Authorized Internet Dealer 1-year Manufacturer's Warranty What's in the box: Alpine S2-S65 owner's manual Two 2-way speakers 2 Adapter rings Two 12" Lengths of speaker wire Eight 1-1/8" Screws Eight M4x6.5mm Machine screws with split lock washers attached Eight M4 Nuts 6 Flat washers Warranty information Online product registration information Alpine BBX-F1200 600W Max (280W RMS) 2-ohm Stable 4 Channel Class-A/B Amplifier This new BBX amplifier gives you Alpine power performance at a fantastic price. And they’re designed to fit easily in virtually any system. High Power, Great Value This amp delivers high output power and exceptional performance for their class. A great way to expand your sound system on a limited budget. High Pass and Low Pass Filters These two filters let you set the frequency points for the high, mid, and bass ranges to match your speakers and ensure optimum efficiency. Performance With Bass EQ, you can maximize the performance of your system and get even more powerful bass. General Features: Alpine BBX-F1200 Class-A/B 2-ohm Stable 4-Channel Amplifier RMS Power Rating: 4 ohms: 50 watts x 4 channel 2 ohms: 70 watts x 4 channel 1 ohm: ------------N/A------------ Bridged, 4 ohms: 130 watts x 2 channel Total power output: 600 watts Pulse Width Modulated MOSFET power supply LED power (green) and protect (red) indicators Soft start turn-on 4/3/2 or channel operation 3-way protection circuitry (thermal, overload, and speaker short protection) Dual speaker terminals simplify the hookup of multiple speakers Heavy-duty aluminum alloy heat-sink Input sensitivity: .2V - 8V Frequency Response: 5 - 50000 Hz Total Harmonic Distortion (THD): <1% Signal to Noise Ratio: 95dB Variable high-pass filter: 50 - 500 Hz Variable low-pass filter: 50 - 500 Hz Variable Bass Boost: 0 to +12 dB bass boost Fuse Rating: 40A x 1 Dimensions: 9.4"W x 12.9"L x 2"H Authorized Dealer 1-year Manufacturer's Warranty. Absolute KIT4 Complete PRO Marine 4 Gauge 2000 Watts Amplifier Complete Installation Amp Kit Power Wiring with Red Accent Color Scheme Installing a car amplifier is already enough of a job without worrying about where to find the correct wire and installation accessories. You might not know that some companies are playing gimmicks, and you could get ripped off! Today, I recommend KIT4 for all DIY and installers. This wiring kit has an easy-to-install AGU fuse holder and some perfect wiring. The positive and negative power wires are made with copper-coated aluminum (CCA) wiring to keep costs down but remain highly flexible and installer-friendly. The speaker wire kicks ass, and I was not expecting such a high-quality roll of speaker wire to be included. It feels great, works great, and is much better than the typical 18 AWG wire most kits would consist of. General Features: Complete 4 Gauge Amplifier Kit Designed specifically for car audio systems up to 1000 watts Premium power and ground wire provide optimal power transfer Includes 2-channel RCA interconnect cables for the audio signal connection from the receiver to the amplifier Terminals are gold-plated for excellent signal transfer For use in any car, truck, RV, or boat Authorized Internet Dealer 1-year Manufacturer's warranty Package Includes: 17 ft. of red 4 AWG high current power cable Three ft. of black 4 AWG ground cable 15 ft. of RCA triple shielded interconnect audio cable with built-in remote wire 20 ft. of 12 AWG OFC Speaker cable 20 ft. of 16 AWG remote turn-on wire Six ft. of split loom tubing 1 Gold-plated 80 AMP AGU fuse 1 4 AWG gold ring terminal 1 4 AWG water-resistant inline fuse holder 2 Ring terminals 2 Spade terminals (4 gauge) 5 Spade terminals (14-16 gauge) 3 Self-tapping screws 1 Rubber grommet 20 Black cable ties 2 Butt connectors (18-22 gauge) 1 Butt connector (4 gauge) Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

2 Pair Alpine S2-S65 6.5" 480 Watt Car Audio Speakers+BBX-F1200 4 Channel Amplifier + Absolute KIT4 4G Amp Kit Alpine S2-S65 120W 6.5" 2-Way Type-E Coaxial Car Speakers w/ Silk Tweeters Hearing is BelievingStep up your factory speakers to an affordable upgrade with the all-new Alpine Type-E speakers for the performance-packed sound quality you expect from Alpine.Quality over QuantityJust because you want better sound in your car doesn’t mean you have to break your budget. The Type-E speakers are the perfect, affordable option if you need replacement speakers or want to start building a sound system.Soft Dome Tweeter TechnologyTo output quality sound, the Type-E speakers are developed using soft dome tweeters rather than traditional cone-type tweeters, which can be harsh. This results in a more enjoyable listening experience in the car when playing back music or other entertainment over your sound system.General Features: 6-1/2" S Series 2-way Coaxial Car Speakers Peak Power Handling: 480 watts per pair / 240 watts each RMS Power Handling: 160 watts per pair / 80 watts each Hi-Res Audio-certified Polypropylene, Glass Fiber, and Mica cone material High-Amplitude Multi-Roll (HAMR) speaker surround 1" Cloth Dome tweeters voice coil Ferrite magnet motor structure Top-mount Depth: 2-5/16" Cutout Dimensions: 5-1/8" Impedance: 4 ohms Frequency Response: 70 - 40,000 Hz Sensitivity: 88 dB Speaker grilles are optional and sold separately Authorized Internet Dealer 1-year Manufacturer's Warranty What's in the box: Alpine S2-S65 owner's manual Two 2-way speakers 2 Adapter rings Two 12" Lengths of speaker wire Eight 1-1/8" Screws Eight M4x6.5mm Machine screws with split lock washers attached Eight M4 Nuts 6 Flat washers Warranty information Online product registration information Alpine BBX-F1200 600W Max (280W RMS) 2-ohm Stable 4 Channel Class-A/B Amplifier This new BBX amplifier gives you Alpine power performance at a fantastic price. And they’re designed to fit easily in virtually any system. High Power, Great Value This amp delivers high output power and exceptional performance for their class. A great way to expand your sound system on a limited budget. High Pass and Low Pass Filters These two filters let you set the frequency points for the high, mid, and bass ranges to match your speakers and ensure optimum efficiency. Performance With Bass EQ, you can maximize the performance of your system and get even more powerful bass. General Features: Alpine BBX-F1200 Class-A/B 2-ohm Stable 4-Channel Amplifier RMS Power Rating: 4 ohms: 50 watts x 4 channel 2 ohms: 70 watts x 4 channel 1 ohm: ------------N/A------------ Bridged, 4 ohms: 130 watts x 2 channel Total power output: 600 watts Pulse Width Modulated MOSFET power supply LED power (green) and protect (red) indicators Soft start turn-on 4/3/2 or channel operation 3-way protection circuitry (thermal, overload, and speaker short protection) Dual speaker terminals simplify the hookup of multiple speakers Heavy-duty aluminum alloy heat-sink Input sensitivity: .2V - 8V Frequency Response: 5 - 50000 Hz Total Harmonic Distortion (THD): <1% Signal to Noise Ratio: 95dB Variable high-pass filter: 50 - 500 Hz Variable low-pass filter: 50 - 500 Hz Variable Bass Boost: 0 to +12 dB bass boost Fuse Rating: 40A x 1 Dimensions: 9.4"W x 12.9"L x 2"H Authorized Dealer 1-year Manufacturer's Warranty. Absolute KIT4 Complete PRO Marine 4 Gauge 2000 Watts Amplifier Complete Installation Amp Kit Power Wiring with Red Accent Color Scheme Installing a car amplifier is already enough of a job without worrying about where to find the correct wire and installation accessories. You might not know that some companies are playing gimmicks, and you could get ripped off! Today, I recommend KIT4 for all DIY and installers. This wiring kit has an easy-to-install AGU fuse holder and some perfect wiring. The positive and negative power wires are made with copper-coated aluminum (CCA) wiring to keep costs down but remain highly flexible and installer-friendly. The speaker wire kicks ass, and I was not expecting such a high-quality roll of speaker wire to be included. It feels great, works great, and is much better than the typical 18 AWG wire most kits would consist of. General Features: Complete 4 Gauge Amplifier Kit Designed specifically for car audio systems up to 1000 watts Premium power and ground wire provide optimal power transfer Includes 2-channel RCA interconnect cables for the audio signal connection from the receiver to the amplifier Terminals are gold-plated for excellent signal transfer For use in any car, truck, RV, or boat Authorized Internet Dealer 1-year Manufacturer's warranty Package Includes: 17 ft. of red 4 AWG high current power cable Three ft. of black 4 AWG ground cable 15 ft. of RCA triple shielded interconnect audio cable with built-in remote wire 20 ft. of 12 AWG OFC Speaker cable 20 ft. of 16 AWG remote turn-on wire Six ft. of split loom tubing 1 Gold-plated 80 AMP AGU fuse 1 4 AWG gold ring terminal 1 4 AWG water-resistant inline fuse holder 2 Ring terminals 2 Spade terminals (4 gauge) 5 Spade terminals (14-16 gauge) 3 Self-tapping screws 1 Rubber grommet 20 Black cable ties 2 Butt connectors (18-22 gauge) 1 Butt connector (4 gauge) Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.  

2 Alpine R2-S65 (RS652) 300W MAX 100W RMS R-Series 6-1/2" 2-way Car Speakers with Absolute 20' Speaker Wire Package   TURN IT UP WITHOUT TURNING DOWN SOUND QUALITY If you play your music loud and want others to know, the R-Series speakers are the match for you. You will enjoy a center sound stage with speakers that play loud and clear without distortion. The R-Series speakers are tuned with an emphasis on the high- and low-end frequencies, so they deliver power while naturally producing bright, active sound. They are the perfect power and performance match for the R-Series subwoofers and amplifiers. General Features: 6.5" R-Series 2-way Coaxial Car Speakers carbon-fiber-reinforced polymer (CFRP) woofer Peak Power Handling: 600 watts per pair / 300 watts each RMS Power Handling: 200 watts per pair / 100 watts each Glass Fiber cone material Rubber HAMR Surround Composite Basket Hi-Res Audio Certified 1" Magnesium Hard Dome Tweeters CEA-2031 compliant: Yes Ferrite magnet motor structure Top-mount Depth: 2.48" Cutout Dimensions: 5.31" Impedance: 4 ohms Frequency Response: 65 - 40,000 Hz Sensitivity: 88 dB Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the R2-S65 package: R2-S65 owner's manual Two 2-way Speakers Two 6-1/2" Adapter rings 2 Grilles 2 Grille badges Eight 1-1/8" Screws Eight M4x12mm Machine screws 8 Speed clips Warranty information Important Notice Online product registration information Template and specs on the box Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

2 Alpine R2-S65 (R2S65) 300W MAX 100W RMS R-Series 6-1/2" 2-way Car Speakers TURN IT UP WITHOUT TURNING DOWN SOUND QUALITY If you play your music loud and want others to know, the R-Series speakers are the match for you. You will enjoy a center sound stage with speakers that play loud and clear without distortion. The R-Series speakers are tuned with an emphasis on the high- and low-end frequencies, so they deliver power while naturally producing bright, active sound. They are the perfect power and performance match for the R-Series subwoofers and amplifiers. MORE OUTPUT FOR MORE FUN The woofers have a large, 35-millimeter (mm) voice coil, which allows for more coil windings to fit in the gap. This results in greater heat dissipation and increased power handling for superior control and output. The R-Series speakers incorporate Alpine’s patented High-Amplitude Multi-Roll Surround (H.A.M.R.) for control and accuracy. The component models use a crossover with an in-line, passive design and a reduced footprint, which contributes to more straightforward installation. General Features: 6.5" R-Series 2-way Coaxial Car Speakers carbon-fiber-reinforced polymer (CFRP) woofer Peak Power Handling: 600 watts per pair / 300 watts each RMS Power Handling: 200 watts per pair / 100 watts each Glass Fiber cone material Rubber HAMR Surround Composite Basket Hi-Res Audio Certified 1" Magnesium Hard Dome Tweeters CEA-2031 compliant: Yes Ferrite magnet motor structure Top-mount Depth: 2.48" Cutout Dimensions: 5.31" Impedance: 4 ohms Frequency Response: 65 - 40,000 Hz Sensitivity: 88 dB Authorized Internet Dealer 1-year Manufacturer's Warranty What's in the R2-S65 package: R2-S65 owner's manual Two 2-way Speakers Two multi-purpose adapter rings 2 Grilles 8 Speed clips Warranty information Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine R2-S65 300W 6.5" Coaxial + Alpine R2-S65C Component Speakers+Alpine R2-A60F Amplifier + Absolute KIT4 4 Gauge Amp Kit Bundle  Alpine R-S65C.2 100W RMS 6.5" R-Series Component 2-Way Speakers TURN IT UP If you play your music loud and want others to know, the R-Series speakers are the match for you. You’ll enjoy a center sound stage with speakers that play loud and clear without distortion. The R-Series speakers are tuned with an emphasis on the high- and low-end frequencies, so they deliver power while naturally producing bright, active sound. They are the perfect power and performance match for the R-Series subwoofers and amplifiers. General Features: 6.5-inch R-Series Component 2-way Car Speakers The component speaker system includes two woofers, two tweeters, and two external crossovers Power Handling: Peak: 300 watts RMS: 100 watts 4 Ohms impedance Frequency response: 65Hz-40kHz Carbon Fiber Reinforced Polymer (CFRP) exclusive cone technology CFRP increases the speakers’ mid-bass performance and dynamic range CFRP is used as a tweeter diaphragm, enabling the system to perform up to 45 kHz range, making the speakers compliant with High-Resolution Audio playback Patented High-Amplitude Multi-Roll (HAMR) surround, for control and accuracy Ideal for tight installations and use matching speaker grills that are shallower as well (sold separately) Uses an in-line, passive design with a reduced footprint, which also contributes to easier installation Authorized Dealer 1-year Manufacturer's Warranty Alpine R2-S65.2 (RS652) 300W MAX 100W RMS R-Series 6-1/2" 2-way Car Speakers TURN IT UP WITHOUT TURNING DOWN THE SOUND QUALITY If you play your music loud and want others to know, the R-Series speakers are the match for you. You will enjoy a center sound stage with speakers that play loud and clear without distortion. The R-Series speakers are tuned with an emphasis on the high- and low-end frequencies, so they deliver power while naturally producing bright, active sound. They are the perfect power and performance match for the R-Series subwoofers and amplifiers. General Features: 6-1/2" 2-way car speakers (pair) carbon-fiber-reinforced polymer (CFRP) woofer the carbon-fiber-reinforced polymer dome tweeter handles up to 100 watts RMS (300 watts peak power) frequency response: 65-40,000 Hz sensitivity: 88 dB top-mount depth: 2-5/8" grilles included Authorized Dealer 1-year Manufacturer's Warranty Alpine R2-A60F R-Series 4-Channel Power Density Amplifier 600 Watts RMSHI-RESOLUTION AUDIO COMPLIANTThe R-Series amplifiers utilize Alpine’s advanced amplifier platform that takes the classic Class-D amplifier circuit and adds dual post-filter feedback loops for unmatched accuracy and control. This technology., Initially launched in the premium X-Series amplifiers, the R-Series amplifiers produce efficient power with enhanced dynamic range, qualifying them to be Hi-Resolution Audio compliant.THE LOUDEST FAMILY ON THE BLOCKThe “R” line of speakers and subwoofers has a heritage of sound quality you can hear from a block away, and the newly added R-Series amplifiers are no exception. Aside from their best-in-class performance, these amplifiers are tuned to emphasize the characteristics of the R-Series speakers and subwoofers, giving you that legendary R-Series experience.General Features: Alpine R2-A60F Alpine R-Series 4-Channel Power Density Amplifier RMS Power Output: 100 Watts x 4 @ 4 Ohm 150 Watts x 4 @ 2 Ohm 300 Watts x 2 @ 4 Ohms Bridged Class-D Amplifier Frequency Response: 15 Hz - 45 kHz S/N ratio: 87dB (ref: 1W into 4 ohms), >106dB (ref: rated power into 4 ohms) Only 46 degrees of phase shift Hi-Resolution Audio Compliant Designed to match perfectly with the R-Series subwoofers (12, 10, and 8-inch sizes available) and the new R-Series speakers. Fuse Rating: 30A x 2 Approximate Weight: 11 lbs Dimensions: 10-3/4" W x 2-1/16" H x 10" D Authorized Dealer 1-year Manufacturer's Warranty Absolute KIT4 Complete PRO Marine 4 Gauge 2000 Watts Amplifier Complete Installation Amp Kit Power Wiring with Red Accent Color Scheme Installing a car amplifier is already enough of a job without having to worry about where to find the right wire and installation accessories. What you might not know is that some companies are playing tricks, and you could end up getting ripped off! Today, I recommend KIT4 for all DIY and installers. This is a wiring kit with an easy-to-install AGU fuse holder and some seriously good wiring. The positive and negative power wires are made with copper-coated aluminum (CCA) wiring to keep costs down but remain highly flexible and installer-friendly. The speaker wire kicks ass, and I was not expecting such a high-quality roll of speaker wire to be included. It feels and works great, and it is much better than the typical 18 AWG wire most kits would include. General Features: Complete 4 Gauge Amplifier Kit Designed specifically for car audio systems up to 1000 watts Premium power and ground wire provide optimal power transfer Includes 2-channel RCA interconnect cables for the audio signal connection from the receiver to the amplifier Terminals are gold-plated for excellent signal transfer For use in any car, truck, RV, or boat Authorized Internet Dealer 1-year Manufacturer's warranty Package Includes: 17 ft. of red 4 AWG high current power cable 3 ft. of black 4 AWG ground cable 15 ft. of RCA triple shielded interconnect audio cable with built-in remote wire 20 ft. of 12 AWG OFC Speaker cable 20 ft. of 16 AWG remote turn-on wire 6 ft. of split loom tubing 1 Gold-plated 80 AMP AGU fuse 1 4 AWG gold ring terminal 1 4 AWG water-resistant inline fuse holder 2 Ring terminals 2 Spade terminals (4 gauge) 5 Spade terminals (14-16 gauge) 3 Self-tapping screws 1 Rubber grommet 20 Black cable ties 2 Butt connectors (18-22 gauge) 1 Butt connector (4 gauge) Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.  

ALPINE R2-S65 300 Watt 6.5" Car Audio Coaxial 2-Way Speakers + Metra 72-6512 Speaker Harness Connector Compatible Fit for Chrysler Vehicles 90-07+Cherokee Alpine R2-S65 (RS652) 300W MAX 100W RMS R-Series 6-1/2" 2-way Car Speakers TURN IT UP WITHOUT TURNING DOWN SOUND QUALITY If you play your music loud and want others to know, the R-Series speakers are the match for you. You will enjoy a center sound stage with speakers that play loud and clear without distortion. The R-Series speakers are tuned with an emphasis on the high- and low-end frequencies, so they deliver power while naturally producing bright, active sound. They are the perfect power and performance match for the R-Series subwoofers and amplifiers. General Features: 6.5" R-Series 2-way Coaxial Car Speakers carbon-fiber-reinforced polymer (CFRP) woofer Peak Power Handling: 600 watts per pair / 300 watts each RMS Power Handling: 200 watts per pair / 100 watts each Glass Fiber cone material Rubber HAMR Surround Composite Basket Hi-Res Audio Certified 1" Magnesium Hard Dome Tweeters CEA-2031 compliant: Yes Ferrite magnet motor structure Top-mount Depth: 2.48" Cutout Dimensions: 5.31" Impedance: 4 ohms Frequency Response: 65 - 40,000 Hz Sensitivity: 88 dB Authorized Internet Dealer 1-year Manufacturer's Warranty Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.