Car Audio & Video Packages & Bundles (715)

Absolute USA KITCAP4GASI Combined Amp Kit & Capacitor Package, 3.0 Farad Power Capacitor 4 Gauge Car Amplifier Installation Wiring Complete Kit Combined Universal Amp Kit & Capacitor Package Include 3.0 Farad Power Capacitor and Complete Amplifier 4 Gauge Kit ABSOLUTE CAP300 1.0 Farad 20V Digital Capacitor with Digital Read-Out Built-in Distribution Block A capacitor is a passive (a component that consumes but does not produce energy) two-terminal electrical component. In building a sound system for your car, you would want to use a capacitor for a couple of different reasons. The main reason a capacitor is always recommended is for power reserve. The capacitor stores energy and releases it very quickly to the amplifier(s). How does this help? It’s very simple: Music is dynamic, no matter what type you listen to. The dynamics in musical content can vary from soft voices, and very quickly transition to thundering bass notes. These moments are where the benefit of having a capacitor is heard. The amplifier requires a constant amount of steady power to function efficiently and power the speakers. A capacitor will keep the power going to the amplifier consistent and stabilized, which means a better sounding system. IMPORTANT: The remote output of the head unit is connected to the remote turn-on of the capacitor. The capacitor will not function if the remote wire is not connected to your head unit. CHARGING THE CAPACITOR First, make sure that all the connections according to the diagrams in the instruction manual are correct. Pick up the cable coming from the POSITIVE (+) battery terminal. Place the supplied charging resistor between the end of this cable and the positive terminal of the capacitor. The capacitor will begin charging. Charging generally takes 5 to 60 seconds. During charging, the voltage shown in the 3 digit display will rise rapidly, then slow as it approaches the voltage of your vehicle’s battery. When fully charged, the display voltage will stop rising. If you have a voltmeter, you can first measure the voltage of your car battery. Then you will know with accuracy that the capacitor is fully charged. CAUTION!! During charging, the resistor will become hot. This is normal, but exercise caution during the charging process. After charging is complete, remove the resistor from the incoming positive cable, and IMMEDIATELY connect it to the positive terminal of the capacitor. General Features: 3 Farad Digital Capacitor With 3000 Watts Runs On 10-16 Volts DC Audible Warning Tone for Reverse Polarity, Voltage Overload, and Low Battery Voltage Capacitance: 3,000,000, Capacitance Tolerance: + / - 10%, Voltage Measurement Accurate To + / - 0.1 VDC Equivalent Series Resistance: 0.00195 Mw @ 120 Hz / 25°C You May Also Hook Up as Many as You Like in Parallel to Make a Bank of Power Stabilizing Amplifier Flow Capacity High Strength Cylindrical Aluminum Housing Soft Turn-On/Off Power Surge Bright Charging Status L.E.D. Digital Over-Voltage Protection System Perfect for Systems Up to 3000W Max Increases Level of Bass, And the Peak Power of Your Amp Features Audible Warning Indicators Runs On 10-16 Volts Dc Equipped with Automatic Shutoff Protection Accepts Any Gauge of Wire with Ring Terminals 3 Farad Digital Power Capacitor 24 Volts Surge Ultra-Low ESR (Super Low Internal Resistance ) 3 Digit Bright Red Digital Led Voltage Display Audible Warning Tone for Reverse Polarity, Voltage Overload, And Low Battery Voltage Capacitance: 3,000,000 Capacitance Tolerance: + / - 10%, Voltage Measurement Accurate To + / - 0.1 VDC Working Voltage: 10-16 VDC, Automatic Shutoff Protection Includes Clear Mounting Brackets Includes the Resistor for Charging Reduce or Stop the Dimming of Your Headlights Accepts any gauge of wire with ring terminals Width of Mounting Bracket Base: 5-1/2" Dimensions: 11-3/4"H X 3-1/2"W X 3-1/2"D 3 Year Warranty Equivalent Series Resistance: You May Also Hook Up as Many as You Like in Parallel to Make A Bank of Power. Absolute KIT4 Complete PRO Marine 4 Gauge 2000 Watts Amplifier Complete Installation Amp Kit Power Wiring with Blue Accent Color Scheme Installing a car amplifier is already enough of a job without having to worry about where to find the right wire and installation accessories. What you might not know is that there are some gimmicks being played by some companies and you could end up getting ripped off! Today, I would recommend KIT4 for all DIY and Installer. This is a wiring kit with an easy-to-install AGU fuse holder and some seriously good wiring. The positive and negative power wires are made with copper-coated aluminum (CCA) wiring to keep costs down but remain highly flexible and installer-friendly. The speaker wire kicks ass, and I was not expecting such a high-quality roll of speaker wire to be included. It feels and works great, and it is much better than the typical 18 AWG wire most kits would include. General Features: Complete 4 Gauge Amplifier Kit Designed specifically for car audio systems up to 1000 watts Premium power and ground wire provide optimal power transfer Includes 2-channel RCA interconnect cables for the audio signal connection from the receiver to the amplifier Terminals are gold-plated for excellent signal transfer For use in any car, truck, RV, or boat Authorized Internet Dealer 1-year Manufacturer's warranty Package Includes: 17 ft. of red 4 AWG high current power cable 3 ft. of black 4 AWG ground cable 15 ft. of RCA triple shielded interconnect audio cable with built-in remote wire 20 ft. of 12 AWG OFC Speaker cable 20 ft. of 16 AWG remote turn-on wire 6 ft. of split loom tubing 1 Gold plated 80 AMP AGU fuse 1 4 AWG gold ring terminal 1 4 AWG water-resistant inline fuse holder 2 Ring terminals 2 Spade terminals (4 gauge) 5 Spade terminals (14-16 gauge) 3 Self-tapping screws 1 Rubber grommet 20 Black cable ties 2 Butt connectors (18-22 gauge) 1 Butt connector (4 gauge) ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Rockford Fosgate Two Punch P3 12" Subwoofers in a Ported Enclosure with a Punch Series P1000X1bd Amplifier Rockford Fosgate Punch P1000X1bd Mono subwoofer amplifier 1,000 watts RMS x 1 at 1 ohm The Punch P1000X1bd mono amplifier pumps out 1,000 Watts into a 1-Ohm load. The Class-BD technology produces bass more efficiently over traditional amps, and its frequency response is optimized for subwoofers. With its super-efficient Class-BD circuit topology, the P1000X1bd assures maximum BOOM for your buck! Due to its dedicated low-frequency response, this amplifier is optimized for mid-bass speakers or subwoofers only. No need to worry because its 1-ohm capability will easily drive a pair of 4-ohm DVC subwoofers or quad-configuration of 2-ohm DVC subwoofers. General Features: Punch BD Series Monoblock Class BD Car Amplifier RMS Power Rating: 4 ohms: 300 watts x 1 channel 2 ohms: 500 watts x 1 channel 1 ohm: 1000 watts x 1 channel CEA-2006 compliant amplifier Features C.L.E.A.N. Set-up with the 10-step set-up procedure w/ input/output clip detection and indicator LEDs MOSFET power supply Muted turn on Cast aluminum heatsink 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protection indicators Nickel-plated captive C-clamp terminals Ultra-efficient Class BD circuitry to maximize amplifier power efficiency On-board differential inputs eliminate noise picked up by the signal cable Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately) MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowering the operating temperature and potential for noise - similar to circuit boards designed by aerospace manufacturers Input sensitivity: 150mV - 12V On-board Punch EQ with +18dB boost @ 45Hz. Variable low-pass filter: 50-250 Hz Selectable infrasonic filter: off / 28 Hz Frequency response: 20 - 250 Hz Total Harmonic Distortion: <1.0% Dimensions: 13-5/16"L x 7-3/4"W x 2-3/8"H 8 AWG to 18 AWG speaker wire output terminals 4 gauge power and ground wiring is recommended for installation. Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the P1000X1bd package: P1000X1bd owner's manual Mono subwoofer amplifier Four 1-1/2" Self-tapping screws 5mm Allen wrench Quick setup instructions Rockford Fosgate P3-2X12 Punch Dual P3 12" Loaded Enclosure Ported Subwoofer The P3-2X12 is a dual P3 12” vented enclosure with 1200 Watts RMS power handling wired to a 1-Ohm load. The enclosure is constructed with 5/8” MDF, covered in high-density carpet, and features quick-release compression terminals. General Features: Subwoofer Features: 12" Punch P3 Series Subwoofers Power Handling: Peak: 2400 watts RMS: 1200 watts Recommended power range: 600 - 1400 watts RMS @ 1 ohm CEA-2031 Compliant Klippel Verified Flex-fit Mounting pattern Proprietary spider venting/cooling technique StampCast basket with integrated spider venting Sturdy 16 gauge compound bend frame geometry High modulus Kevlar re-inforced paper-pulp cone Semi-flexible, PVC removable protective motor cover Multi-point high-temp/high-strength neck joint bonding technique Tall-profile VAST Santoprene surround for a larger surface area Dual tear & fatigue resistant poly-cotton spider with woven tinsel leads Fatigue-resistant and reduced strain "stitched on" flexible lead wire design Proprietary all metal, radially oriented compression input terminal assembly Optimized motor magnetics with extended pole and bumped vented backplate High temp 2.5" voice coil w/ spun-laced Nome insulating reinforcement collar Die-Cast aluminum soft-touch painted trim ring allows for optional integrated grill Magnet Weight: 96 oz Frequency Response: 27.7 - 250 Hz Xmax: 15.9mm Sensitivity: 85 dB @ 1 watt / 1 meter Authorized Internet Dealer 1-year Manufacturer's Warranty Enclosure Features: Dual Punch P3 12" Loaded Subwoofer Enclosure Constructed with durable 5/8" MDF High current binding posts Proprietary high-flow, low-noise port Durable black carpet covering Computer-optimized design Final Impedance: 1 ohm Dimensions: 15-3/4”D x 33-7/8”W x 15-1/8”H Shipping Weight: 89.65 Lbs. (40.66 kg) ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.