Car Audio & Video
-51% sale
ABSOLUTE CAP400B 4 FARAD POWER CAR CAPACITOR FOR ENERGY STORAGE TO ENHANCE BASS DEMAND FROM AUDIO SYSTEM (BLUE)
Absolute USA ABSOLUTE CAP400B 4 FARAD POWER CAR CAPACITOR FOR ENERGY STORAGE TO ENHANCE BASS DEMAND FROM AUDIO SYSTEM (BLUE) $79.99 $159.99
ABSOLUTE CAP400B 4 FARAD POWER CAR CAPACITOR FOR ENERGY STORAGE TO ENHANCE BASS DEMAND FROM AUDIO SYSTEM (BLUE) PRODUCT FEATURES: PERFECT FOR SYSTEMS UP TO 5000W MAX INCREASES LEVEL OF BASS, AND THE PEAK POWER OF YOUR AMP FEATURES AUDIBLE WARNING INDICATORS RUNS ON 10-16 VOLTS DC EQUIPPED WITH AUTOMATIC SHUTOFF PROTECTION ACCEPTS ANY GAUGE OF WIRE WITH RING TERMINALS 4 FARAD DIGITAL POWER CAPACITOR 24 VOLTS SURGE ULTRA-LOW ESR 3 DIGIT BRIGHT RED DIGITAL LED VOLTAGE DISPLAY AUDIBLE WARNING TONE FOR REVERSE POLARITY, VOLTAGE OVERLOAD, AND LOW BATTERY VOLTAGE CAPACITANCE: 4,000,000, CAPACITANCE TOLERANCE: + / - 10%, VOLTAGE MEASUREMENT ACCURATE TO + / - 0.1 VDC WORKING VOLTAGE: 10-16 VDC, EQUIVALENT SERIES RESISTANCE: <0.00195 MW @ 120 HZ / 25°C YOU MAY ALSO HOOK UP AS MANY AS YOU LIKE IN PARALLEL TO MAKE A BANK OF POWER. AUTOMATIC SHUTOFF PROTECTION INCLUDES CLEAR MOUNTING BRACKETS INCLUDES THE RESISTOR FOR CHARGING REDUCE OR STOP THE DIMMING OF YOUR HEADLIGHTS WIDTH OF MOUNTING BRACKET BASE: 5-1/2" DIMENSIONS: 11-3/4"H X 3-1/2"W X 3-1/2"D 3 YEAR WARRANTY
-51% sale
ABSOLUTE CAP350R 3.5 FARAD POWER CAR CAPACITOR FOR ENERGY STORAGE TO ENHANCE BASS DEMAND FROM AUDIO SYSTEM (RED)
Absolute USA ABSOLUTE CAP350R 3.5 FARAD POWER CAR CAPACITOR FOR ENERGY STORAGE TO ENHANCE BASS DEMAND FROM AUDIO SYSTEM (RED) $59.99 $119.99
Absolute CAP350BR 3.5 Farad Red Power Car Capacitor for Energy Storage to Enhance Bass Demand From Audio System Car Audio Capacitor is Used to Prevent Dimming of Dash Lights and Headlights When Playing Loud Bass Notes. They Work by Supplying the Car Amplifier with Rapid Jolts of Power. A Car Audio Power Cap Works by Storing Large Amounts of Electrical Power Which It Can Then Deliver to Power Hungry Components When Called Upon to Do So. They Have an Advantage Over Typical Lead Acid Storage Batteries Because They Have Very Low Internal Resistance. This Allows Them to Deliver Large Amounts of Power (Current) Very Quickly. Much Faster Than A Car's Charging System Can Deliver That Same Amount of Current. Car Audio Power Amplifiers Can Have Very Large Current Demands. This Is Dependent on The Music Being Played Through the Amplifier. Typically, These Currents Are Only Needed in Short Bursts During Transient Peaks (Bass Drum Note, Etc.). If the Amplifier Tries to Pull This Current from The Electrical System Directly It May Cause A Drop in Voltage Called A Sag. This Sag Is Equivalent to A Voltage Drop in The System and The Size of The Drop Depends on The Resistance of The Wire from The Source (Battery) to the Amplifier. CHARGING THE CAPACITOR First, make sure that all the connections according to the diagrams in the instruction manual are correct. Pick up the cable coming from the POSITIVE (+) battery terminal. Place the supplied charging resistor between the end of this cable and the positive terminal of the capacitor. The capacitor will begin charging. Charging generally takes 5 to 60 seconds. During charging, the voltage shown in the 3 digit display will rise rapidly, then slow as it approaches the voltage of your vehicle’s battery. When fully charged, the display voltage will stop rising. If you have a voltmeter, you can first measure the voltage of your car battery. Then you will know with accuracy that the capacitor is fully charged. CAUTION!! During charging, the resistor will become hot. This is normal, but exercise caution during the charging process. After charging is complete, remove the resistor from the incoming positive cable, and IMMEDIATELY connect it to the positive terminal of the capacitor. General Features: 3.5 Farad Digital Capacitor With 3000 Watts Runs On 10-16 Volts DC Audible Warning Tone for Reverse Polarity, Voltage Overload, and Low Battery Voltage Capacitance: 3,500,000, Capacitance Tolerance: + / - 10%, Voltage Measurement Accurate To + / - 0.1 VDC Equivalent Series Resistance: 0.00195 Mw @ 120 Hz / 25°C You May Also Hook Up as Many as You Like in Parallel to Make a Bank of Power Stabilizing Amplifier Flow Capacity High Strength Cylindrical Aluminum Housing Soft Turn-On/Off Power Surge Bright Charging Status L.E.D. Digital Over-Voltage Protection System Perfect for Systems Up to 3000W Max Increases Level of Bass, And the Peak Power of Your Amp Features Audible Warning Indicators Runs On 10-16 Volts Dc Equipped with Automatic Shutoff Protection Accepts Any Gauge of Wire with Ring Terminals 3.5 Farad Digital Power Capacitor 24 Volts Surge Ultra-Low ESR (Super Low Internal Resistance ) 3 Digit Bright Red Digital Led Voltage Display Audible Warning Tone for Reverse Polarity, Voltage Overload, And Low Battery Voltage Capacitance: 3,500,000 Capacitance Tolerance: + / - 10%, Voltage Measurement Accurate To + / - 0.1 VDC Working Voltage: 10-16 VDC, Automatic Shutoff Protection Includes Clear Mounting Brackets Includes the Resistor for Charging Reduce or Stop the Dimming of Your Headlights Accepts any gauge of wire with ring terminals Width of Mounting Bracket Base: 5-1/2" Dimensions: 11-3/4"H X 3-1/2"W X 3-1/2"D 3 Year Warranty Equivalent Series Resistance: You May Also Hook Up as Many as You Like in Parallel to Make A Bank of Power. ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov
-59% sale
ABSOLUTE CAP300R 3 FARAD POWER CAR CAPACITOR FOR ENERGY STORAGE TO ENHANCE BASS DEMAND FROM AUDIO SYSTEM (RED)
Absolute USA ABSOLUTE CAP300R 3 FARAD POWER CAR CAPACITOR FOR ENERGY STORAGE TO ENHANCE BASS DEMAND FROM AUDIO SYSTEM (RED) $49.99 $119.99
Absolute CAP300R 3 Farad Red Power Car Capacitor for Energy Storage to Enhance Bass Demand From Audio System Car Audio Capacitor is Used to Prevent Dimming of Dash Lights and Headlights When Playing Loud Bass Notes. They Work by Supplying the Car Amplifier with Rapid Jolts of Power. A Car Audio Power Cap Works by Storing Large Amounts of Electrical Power Which It Can Then Deliver to Power Hungry Components When Called Upon to Do So. They Have an Advantage Over Typical Lead Acid Storage Batteries Because They Have Very Low Internal Resistance. This Allows Them to Deliver Large Amounts of Power (Current) Very Quickly. Much Faster Than A Car's Charging System Can Deliver That Same Amount of Current. Car Audio Power Amplifiers Can Have Very Large Current Demands. This Is Dependent on The Music Being Played Through the Amplifier. Typically, These Currents Are Only Needed in Short Bursts During Transient Peaks (Bass Drum Note, Etc.). If the Amplifier Tries to Pull This Current from The Electrical System Directly It May Cause A Drop in Voltage Called A Sag. This Sag Is Equivalent to A Voltage Drop in The System and The Size of The Drop Depends on The Resistance of The Wire from The Source (Battery) to the Amplifier. CHARGING THE CAPACITOR First, make sure that all the connections according to the diagrams in the instruction manual are correct. Pick up the cable coming from the POSITIVE (+) battery terminal. Place the supplied charging resistor between the end of this cable and the positive terminal of the capacitor. The capacitor will begin charging. Charging generally takes 5 to 60 seconds. During charging, the voltage shown in the 3 digit display will rise rapidly, then slow as it approaches the voltage of your vehicle’s battery. When fully charged, the display voltage will stop rising. If you have a voltmeter, you can first measure the voltage of your car battery. Then you will know with accuracy that the capacitor is fully charged. CAUTION!! During charging, the resistor will become hot. This is normal, but exercise caution during the charging process. After charging is complete, remove the resistor from the incoming positive cable, and IMMEDIATELY connect it to the positive terminal of the capacitor. General Features: 3 Farad Digital Capacitor With 3000 Watts Runs On 10-16 Volts DC Audible Warning Tone for Reverse Polarity, Voltage Overload, and Low Battery Voltage Capacitance: 3,000,000, Capacitance Tolerance: + / - 10%, Voltage Measurement Accurate To + / - 0.1 VDC Equivalent Series Resistance: 0.00195 Mw @ 120 Hz / 25°C You May Also Hook Up as Many as You Like in Parallel to Make a Bank of Power Stabilizing Amplifier Flow Capacity High Strength Cylindrical Aluminum Housing Soft Turn-On/Off Power Surge Bright Charging Status L.E.D. Digital Over-Voltage Protection System Perfect for Systems Up to 3000W Max Increases Level of Bass, And the Peak Power of Your Amp Features Audible Warning Indicators Runs On 10-16 Volts Dc Equipped with Automatic Shutoff Protection Accepts Any Gauge of Wire with Ring Terminals 3 Farad Digital Power Capacitor 24 Volts Surge Ultra-Low ESR (Super Low Internal Resistance ) 3 Digit Bright Red Digital Led Voltage Display Audible Warning Tone for Reverse Polarity, Voltage Overload, And Low Battery Voltage Capacitance: 3,000,000 Capacitance Tolerance: + / - 10%, Voltage Measurement Accurate To + / - 0.1 VDC Working Voltage: 10-16 VDC, Automatic Shutoff Protection Includes Clear Mounting Brackets Includes the Resistor for Charging Reduce or Stop the Dimming of Your Headlights Accepts any gauge of wire with ring terminals Width of Mounting Bracket Base: 5-1/2" Dimensions: 11-3/4"H X 3-1/2"W X 3-1/2"D 3 Year Warranty Equivalent Series Resistance: You May Also Hook Up as Many as You Like in Parallel to Make A Bank of Power. ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov
-51% sale
ABSOLUTE CAP350B 3.5 FARAD POWER CAR CAPACITOR FOR ENERGY STORAGE TO ENHANCE BASS DEMAND FROM AUDIO SYSTEM (BLUE)
Absolute USA ABSOLUTE CAP350B 3.5 FARAD POWER CAR CAPACITOR FOR ENERGY STORAGE TO ENHANCE BASS DEMAND FROM AUDIO SYSTEM (BLUE) $59.99 $119.99
Absolute CAP350B 3.5 Farad Blue Power Car Capacitor for Energy Storage to Enhance Bass Demand From Audio System Car Audio Capacitor is Used to Prevent Dimming of Dash Lights and Headlights When Playing Loud Bass Notes. They Work by Supplying the Car Amplifier with Rapid Jolts of Power. A Car Audio Power Cap Works by Storing Large Amounts of Electrical Power Which It Can Then Deliver to Power Hungry Components When Called Upon to Do So. They Have an Advantage Over Typical Lead Acid Storage Batteries Because They Have Very Low Internal Resistance. This Allows Them to Deliver Large Amounts of Power (Current) Very Quickly. Much Faster Than A Car's Charging System Can Deliver That Same Amount of Current. Car Audio Power Amplifiers Can Have Very Large Current Demands. This Is Dependent on The Music Being Played Through the Amplifier. Typically, These Currents Are Only Needed in Short Bursts During Transient Peaks (Bass Drum Note, Etc.). If the Amplifier Tries to Pull This Current from The Electrical System Directly It May Cause A Drop in Voltage Called A Sag. This Sag Is Equivalent to A Voltage Drop in The System and The Size of The Drop Depends on The Resistance of The Wire from The Source (Battery) to the Amplifier. CHARGING THE CAPACITOR First, make sure that all the connections according to the diagrams in the instruction manual are correct. Pick up the cable coming from the POSITIVE (+) battery terminal. Place the supplied charging resistor between the end of this cable and the positive terminal of the capacitor. The capacitor will begin charging. Charging generally takes 5 to 60 seconds. During charging, the voltage shown in the 3 digit display will rise rapidly, then slow as it approaches the voltage of your vehicle’s battery. When fully charged, the display voltage will stop rising. If you have a voltmeter, you can first measure the voltage of your car battery. Then you will know with accuracy that the capacitor is fully charged. CAUTION!! During charging, the resistor will become hot. This is normal, but exercise caution during the charging process. After charging is complete, remove the resistor from the incoming positive cable, and IMMEDIATELY connect it to the positive terminal of the capacitor. General Features: 3.5 Farad Digital Capacitor With 3000 Watts Runs On 10-16 Volts DC Audible Warning Tone for Reverse Polarity, Voltage Overload, and Low Battery Voltage Capacitance: 3,500,000, Capacitance Tolerance: + / - 10%, Voltage Measurement Accurate To + / - 0.1 VDC Equivalent Series Resistance: 0.00195 Mw @ 120 Hz / 25°C You May Also Hook Up as Many as You Like in Parallel to Make a Bank of Power Stabilizing Amplifier Flow Capacity High Strength Cylindrical Aluminum Housing Soft Turn-On/Off Power Surge Bright Charging Status L.E.D. Digital Over-Voltage Protection System Perfect for Systems Up to 3000W Max Increases Level of Bass, And the Peak Power of Your Amp Features Audible Warning Indicators Runs On 10-16 Volts Dc Equipped with Automatic Shutoff Protection Accepts Any Gauge of Wire with Ring Terminals 3.5 Farad Digital Power Capacitor 24 Volts Surge Ultra-Low ESR (Super Low Internal Resistance ) 3 Digit Bright Red Digital Led Voltage Display Audible Warning Tone for Reverse Polarity, Voltage Overload, And Low Battery Voltage Capacitance: 3,500,000 Capacitance Tolerance: + / - 10%, Voltage Measurement Accurate To + / - 0.1 VDC Working Voltage: 10-16 VDC, Automatic Shutoff Protection Includes Clear Mounting Brackets Includes the Resistor for Charging Reduce or Stop the Dimming of Your Headlights Accepts any gauge of wire with ring terminals Width of Mounting Bracket Base: 5-1/2" Dimensions: 11-3/4"H X 3-1/2"W X 3-1/2"D 3 Year Warranty Equivalent Series Resistance: You May Also Hook Up as Many as You Like in Parallel to Make A Bank of Power. ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov
-51% sale
MK AUDIO CAP4F 4 FARAD POWER CAR CAPACITOR FOR ENERGY STORAGE TO ENHANCE BASS DEMAND FROM AUDIO SYSTEM
MK AUDIO MK AUDIO CAP4F 4 FARAD POWER CAR CAPACITOR FOR ENERGY STORAGE TO ENHANCE BASS DEMAND FROM AUDIO SYSTEM $59.99 $119.99
MK AUDIO CAP4F 4 FARAD POWER CAR CAPACITOR FOR ENERGY STORAGE TO ENHANCE BASS DEMAND FROM AUDIO SYSTEM General Features: PERFECT FOR SYSTEMS UP TO 4000W MAX INCREASES LEVEL OF BASS, AND THE PEAK POWER OF YOUR AMP FEATURES AUDIBLE WARNING INDICATORS RUNS ON 10-16 VOLTS DC EQUIPPED WITH AUTOMATIC SHUTOFF PROTECTION ACCEPTS ANY GAUGE OF WIRE WITH RING TERMINALS 4 FARAD DIGITAL POWER CAPACITOR 24 VOLTS SURGE ULTRA-LOW ESR 3 DIGIT BRIGHT RED DIGITAL LED VOLTAGE DISPLAY AUDIBLE WARNING TONE FOR REVERSE POLARITY, VOLTAGE OVERLOAD, AND LOW BATTERY VOLTAGE CAPACITANCE: 4,000,000, CAPACITANCE TOLERANCE: + / - 10%, VOLTAGE MEASUREMENT ACCURATE TO + / - 0.1 VDC WORKING VOLTAGE: 10-16 VDC, EQUIVALENT SERIES RESISTANCE: <0.00195 MW @ 120 HZ / 25°C YOU MAY ALSO HOOK UP AS MANY AS YOU LIKE IN PARALLEL TO MAKE A BANK OF POWER. AUTOMATIC SHUTOFF PROTECTION INCLUDES CLEAR MOUNTING BRACKETS INCLUDES THE RESISTOR FOR CHARGING REDUCE OR STOP THE DIMMING OF YOUR HEADLIGHTS UPC: 847169009723 3 YEAR WARRANTY ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov
-41% sale
Absolute USA KITCAP4GARD 3.0 Farad Power Capacitor 4 Gauge Car Amplifier Installation Wiring Complete Kit (Red)
Absolute USA Absolute USA KITCAP4GARD 3.0 Farad Power Capacitor 4 Gauge Car Amplifier Installation Wiring Complete Kit (Red) $59.99 $99.99
Absolute USA KITCAP4GARD Combined Amp Kit & Capacitor Package, 3.0 Farad Power Capacitor 4 Gauge Car Amplifier Installation Wiring Complete Kit Combined Universal Amp Kit & Capacitor Package Include 3.0 Farad Power Capacitor and Complete Amplifier 4 Gauge Kit ABSOLUTE CAP300 1.0 Farad 20V Digital Capacitor with Digital Read-Out Built-in Distribution Block A capacitor is a passive (a component that consumes but does not produce energy) two-terminal electrical component. In building a sound system for your car, you would want to use a capacitor for a couple of different reasons. The main reason a capacitor is always recommended is for power reserve. The capacitor stores energy and releases it very quickly to the amplifier(s). How does this help? It’s very simple: Music is dynamic, no matter what type you listen to. The dynamics in musical content can vary from soft voices, and very quickly transition to thundering bass notes. These moments are where the benefit of having a capacitor is heard. The amplifier requires a constant amount of steady power to function efficiently and power the speakers. A capacitor will keep the power going to the amplifier consistent and stabilized, which means a better sounding system. IMPORTANT: The remote output of the head unit is connected to the remote turn-on of the capacitor. The capacitor will not function if the remote wire is not connected to your head unit. CHARGING THE CAPACITOR First, make sure that all the connections according to the diagrams in the instruction manual are correct. Pick up the cable coming from the POSITIVE (+) battery terminal. Place the supplied charging resistor between the end of this cable and the positive terminal of the capacitor. The capacitor will begin charging. Charging generally takes 5 to 60 seconds. During charging, the voltage shown in the 3 digit display will rise rapidly, then slow as it approaches the voltage of your vehicle’s battery. When fully charged, the display voltage will stop rising. If you have a voltmeter, you can first measure the voltage of your car battery. Then you will know with accuracy that the capacitor is fully charged. CAUTION!! During charging, the resistor will become hot. This is normal, but exercise caution during the charging process. After charging is complete, remove the resistor from the incoming positive cable, and IMMEDIATELY connect it to the positive terminal of the capacitor. General Features: 3 Farad Digital Capacitor With 3000 Watts Runs On 10-16 Volts DC Audible Warning Tone for Reverse Polarity, Voltage Overload, and Low Battery Voltage Capacitance: 3,000,000, Capacitance Tolerance: + / - 10%, Voltage Measurement Accurate To + / - 0.1 VDC Equivalent Series Resistance: 0.00195 Mw @ 120 Hz / 25°C You May Also Hook Up as Many as You Like in Parallel to Make a Bank of Power Stabilizing Amplifier Flow Capacity High Strength Cylindrical Aluminum Housing Soft Turn-On/Off Power Surge Bright Charging Status L.E.D. Digital Over-Voltage Protection System Perfect for Systems Up to 3000W Max Increases Level of Bass, And the Peak Power of Your Amp Features Audible Warning Indicators Runs On 10-16 Volts Dc Equipped with Automatic Shutoff Protection Accepts Any Gauge of Wire with Ring Terminals 3 Farad Digital Power Capacitor 24 Volts Surge Ultra-Low ESR (Super Low Internal Resistance ) 3 Digit Bright Red Digital Led Voltage Display Audible Warning Tone for Reverse Polarity, Voltage Overload, And Low Battery Voltage Capacitance: 3,000,000 Capacitance Tolerance: + / - 10%, Voltage Measurement Accurate To + / - 0.1 VDC Working Voltage: 10-16 VDC, Automatic Shutoff Protection Includes Clear Mounting Brackets Includes the Resistor for Charging Reduce or Stop the Dimming of Your Headlights Accepts any gauge of wire with ring terminals Width of Mounting Bracket Base: 5-1/2" Dimensions: 11-3/4"H X 3-1/2"W X 3-1/2"D 3 Year Warranty Equivalent Series Resistance: You May Also Hook Up as Many as You Like in Parallel to Make A Bank of Power. Absolute KIT4 Complete PRO Marine 4 Gauge 2000 Watts Amplifier Complete Installation Amp Kit Power Wiring with Blue Accent Color Scheme Installing a car amplifier is already enough of a job without having to worry about where to find the right wire and installation accessories. What you might not know is that there are some gimmicks being played by some companies and you could end up getting ripped off! Today, I would recommend KIT4 for all DIY and Installer. This is a wiring kit with an easy-to-install AGU fuse holder and some seriously good wiring. The positive and negative power wires are made with copper-coated aluminum (CCA) wiring to keep costs down but remain highly flexible and installer-friendly. The speaker wire kicks ass, and I was not expecting such a high-quality roll of speaker wire to be included. It feels and works great, and it is much better than the typical 18 AWG wire most kits would include. General Features: Complete 4 Gauge Amplifier Kit Designed specifically for car audio systems up to 1000 watts Premium power and ground wire provide optimal power transfer Includes 2-channel RCA interconnect cables for the audio signal connection from the receiver to the amplifier Terminals are gold-plated for excellent signal transfer For use in any car, truck, RV, or boat Authorized Internet Dealer 1-year Manufacturer's warranty Package Includes: 17 ft. of red 4 AWG high current power cable 3 ft. of black 4 AWG ground cable 15 ft. of RCA triple shielded interconnect audio cable with built-in remote wire 20 ft. of 12 AWG OFC Speaker cable 20 ft. of 16 AWG remote turn-on wire 6 ft. of split loom tubing 1 Gold plated 80 AMP AGU fuse 1 4 AWG gold ring terminal 1 4 AWG water-resistant inline fuse holder 2 Ring terminals 2 Spade terminals (4 gauge) 5 Spade terminals (14-16 gauge) 3 Self-tapping screws 1 Rubber grommet 20 Black cable ties 2 Butt connectors (18-22 gauge) 1 Butt connector (4 gauge) ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov
-51% sale
ABSOLUTE U.S.A CAP350R 3.5 FARAD POWER CAR CAPACITOR FOR ENERGY STORAGE TO ENHANCE BAS
Absolute USA ABSOLUTE U.S.A CAP350R 3.5 FARAD POWER CAR CAPACITOR FOR ENERGY STORAGE TO ENHANCE BAS $59.99 $119.99
Absolute CAP350R 3.5 Farad Red Power Car Capacitor for Energy Storage to Enhance Bass Demand From Audio System Car Audio Capacitor is Used to Prevent Dimming of Dash Lights and Headlights When Playing Loud Bass Notes. They Work by Supplying the Car Amplifier with Rapid Jolts of Power. A Car Audio Power Cap Works by Storing Large Amounts of Electrical Power Which It Can Then Deliver to Power Hungry Components When Called Upon to Do So. They Have an Advantage Over Typical Lead Acid Storage Batteries Because They Have Very Low Internal Resistance. This Allows Them to Deliver Large Amounts of Power (Current) Very Quickly. Much Faster Than A Car's Charging System Can Deliver That Same Amount of Current. Car Audio Power Amplifiers Can Have Very Large Current Demands. This Is Dependent on The Music Being Played Through the Amplifier. Typically, These Currents Are Only Needed in Short Bursts During Transient Peaks (Bass Drum Note, Etc.). If the Amplifier Tries to Pull This Current from The Electrical System Directly It May Cause A Drop in Voltage Called A Sag. This Sag Is Equivalent to A Voltage Drop in The System and The Size of The Drop Depends on The Resistance of The Wire from The Source (Battery) to the Amplifier. CHARGING THE CAPACITOR First, make sure that all the connections according to the diagrams in the instruction manual are correct. Pick up the cable coming from the POSITIVE (+) battery terminal. Place the supplied charging resistor between the end of this cable and the positive terminal of the capacitor. The capacitor will begin charging. Charging generally takes 5 to 60 seconds. During charging, the voltage shown in the 3 digit display will rise rapidly, then slow as it approaches the voltage of your vehicle’s battery. When fully charged, the display voltage will stop rising. If you have a voltmeter, you can first measure the voltage of your car battery. Then you will know with accuracy that the capacitor is fully charged. CAUTION!! During charging, the resistor will become hot. This is normal, but exercise caution during the charging process. After charging is complete, remove the resistor from the incoming positive cable, and IMMEDIATELY connect it to the positive terminal of the capacitor. General Features: 3.5 Farad Digital Capacitor With 3000 Watts Runs On 10-16 Volts DC Audible Warning Tone for Reverse Polarity, Voltage Overload, and Low Battery Voltage Capacitance: 3,500,000, Capacitance Tolerance: + / - 10%, Voltage Measurement Accurate To + / - 0.1 VDC Equivalent Series Resistance: 0.00195 Mw @ 120 Hz / 25°C You May Also Hook Up as Many as You Like in Parallel to Make a Bank of Power Stabilizing Amplifier Flow Capacity High Strength Cylindrical Aluminum Housing Soft Turn-On/Off Power Surge Bright Charging Status L.E.D. Digital Over-Voltage Protection System Perfect for Systems Up to 3000W Max Increases Level of Bass, And the Peak Power of Your Amp Features Audible Warning Indicators Runs On 10-16 Volts Dc Equipped with Automatic Shutoff Protection Accepts Any Gauge of Wire with Ring Terminals 3.5 Farad Digital Power Capacitor 24 Volts Surge Ultra-Low ESR (Super Low Internal Resistance ) 3 Digit Bright Red Digital Led Voltage Display Audible Warning Tone for Reverse Polarity, Voltage Overload, And Low Battery Voltage Capacitance: 3,500,000 Capacitance Tolerance: + / - 10%, Voltage Measurement Accurate To + / - 0.1 VDC Working Voltage: 10-16 VDC, Automatic Shutoff Protection Includes Clear Mounting Brackets Includes the Resistor for Charging Reduce or Stop the Dimming of Your Headlights Accepts any gauge of wire with ring terminals Width of Mounting Bracket Base: 5-1/2" Dimensions: 11-3/4"H X 3-1/2"W X 3-1/2"D 3 Year Warranty Equivalent Series Resistance: You May Also Hook Up as Many as You Like in Parallel to Make A Bank of Power. ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov
-51% sale
ABSOLUTE CAP350S 3.5 FARAD POWER CAR CAPACITOR FOR ENERGY STORAGE TO ENHANCE BAS
Absolute USA ABSOLUTE CAP350S 3.5 FARAD POWER CAR CAPACITOR FOR ENERGY STORAGE TO ENHANCE BAS $59.99 $119.99
Absolute CAP350S 3.5 Farad Silver Power Car Capacitor for Energy Storage to Enhance Bass Demand From Audio System Car Audio Capacitor is Used to Prevent Dimming of Dash Lights and Headlights When Playing Loud Bass Notes. They Work by Supplying the Car Amplifier with Rapid Jolts of Power. A Car Audio Power Cap Works by Storing Large Amounts of Electrical Power Which It Can Then Deliver to Power Hungry Components When Called Upon to Do So. They Have an Advantage Over Typical Lead Acid Storage Batteries Because They Have Very Low Internal Resistance. This Allows Them to Deliver Large Amounts of Power (Current) Very Quickly. Much Faster Than A Car's Charging System Can Deliver That Same Amount of Current. Car Audio Power Amplifiers Can Have Very Large Current Demands. This Is Dependent on The Music Being Played Through the Amplifier. Typically, These Currents Are Only Needed in Short Bursts During Transient Peaks (Bass Drum Note, Etc.). If the Amplifier Tries to Pull This Current from The Electrical System Directly It May Cause A Drop in Voltage Called A Sag. This Sag Is Equivalent to A Voltage Drop in The System and The Size of The Drop Depends on The Resistance of The Wire from The Source (Battery) to the Amplifier. CHARGING THE CAPACITOR First, make sure that all the connections according to the diagrams in the instruction manual are correct. Pick up the cable coming from the POSITIVE (+) battery terminal. Place the supplied charging resistor between the end of this cable and the positive terminal of the capacitor. The capacitor will begin charging. Charging generally takes 5 to 60 seconds. During charging, the voltage shown in the 3 digit display will rise rapidly, then slow as it approaches the voltage of your vehicle’s battery. When fully charged, the display voltage will stop rising. If you have a voltmeter, you can first measure the voltage of your car battery. Then you will know with accuracy that the capacitor is fully charged. CAUTION!! During charging, the resistor will become hot. This is normal, but exercise caution during the charging process. After charging is complete, remove the resistor from the incoming positive cable, and IMMEDIATELY connect it to the positive terminal of the capacitor. General Features: 3.5 Farad Digital Capacitor With 3000 Watts Runs On 10-16 Volts DC Audible Warning Tone for Reverse Polarity, Voltage Overload, and Low Battery Voltage Capacitance: 3,500,000, Capacitance Tolerance: + / - 10%, Voltage Measurement Accurate To + / - 0.1 VDC Equivalent Series Resistance: 0.00195 Mw @ 120 Hz / 25°C You May Also Hook Up as Many as You Like in Parallel to Make a Bank of Power Stabilizing Amplifier Flow Capacity High Strength Cylindrical Aluminum Housing Soft Turn-On/Off Power Surge Bright Charging Status L.E.D. Digital Over-Voltage Protection System Perfect for Systems Up to 3000W Max Increases Level of Bass, And the Peak Power of Your Amp Features Audible Warning Indicators Runs On 10-16 Volts Dc Equipped with Automatic Shutoff Protection Accepts Any Gauge of Wire with Ring Terminals 3.5 Farad Digital Power Capacitor 24 Volts Surge Ultra-Low ESR (Super Low Internal Resistance ) 3 Digit Bright Red Digital Led Voltage Display Audible Warning Tone for Reverse Polarity, Voltage Overload, And Low Battery Voltage Capacitance: 3,500,000 Capacitance Tolerance: + / - 10%, Voltage Measurement Accurate To + / - 0.1 VDC Working Voltage: 10-16 VDC, Automatic Shutoff Protection Includes Clear Mounting Brackets Includes the Resistor for Charging Reduce or Stop the Dimming of Your Headlights Accepts any gauge of wire with ring terminals Width of Mounting Bracket Base: 5-1/2" Dimensions: 11-3/4"H X 3-1/2"W X 3-1/2"D 3 Year Warranty Equivalent Series Resistance: You May Also Hook Up as Many as You Like in Parallel to Make A Bank of Power. ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov
-59% sale
ABSOLUTE CAP300B Capacitor<br/>3 Farad Blue Power Car Capacitor for Energy Storage to Enhance Bass Demand From Audio System
Absolute USA ABSOLUTE CAP300B Capacitor
3 Farad Blue Power Car Capacitor for Energy Storage to Enhance Bass Demand From Audio System
$49.99 $119.99
Absolute CAP300B 3 Farad Blue Power Car Capacitor for Energy Storage to Enhance Bass Demand From Audio System Car Audio Capacitor is Used to Prevent Dimming of Dash Lights and Headlights When Playing Loud Bass Notes. They Work by Supplying the Car Amplifier with Rapid Jolts of Power. A Car Audio Power Cap Works by Storing Large Amounts of Electrical Power Which It Can Then Deliver to Power Hungry Components When Called Upon to Do So. They Have an Advantage Over Typical Lead Acid Storage Batteries Because They Have Very Low Internal Resistance. This Allows Them to Deliver Large Amounts of Power (Current) Very Quickly. Much Faster Than A Car's Charging System Can Deliver That Same Amount of Current. Car Audio Power Amplifiers Can Have Very Large Current Demands. This Is Dependent on The Music Being Played Through the Amplifier. Typically, These Currents Are Only Needed in Short Bursts During Transient Peaks (Bass Drum Note, Etc.). If the Amplifier Tries to Pull This Current from The Electrical System Directly It May Cause A Drop in Voltage Called A Sag. This Sag Is Equivalent to A Voltage Drop in The System and The Size of The Drop Depends on The Resistance of The Wire from The Source (Battery) to the Amplifier. CHARGING THE CAPACITOR First, make sure that all the connections according to the diagrams in the instruction manual are correct. Pick up the cable coming from the POSITIVE (+) battery terminal. Place the supplied charging resistor between the end of this cable and the positive terminal of the capacitor. The capacitor will begin charging. Charging generally takes 5 to 60 seconds. During charging, the voltage shown in the 3 digit display will rise rapidly, then slow as it approaches the voltage of your vehicle’s battery. When fully charged, the display voltage will stop rising. If you have a voltmeter, you can first measure the voltage of your car battery. Then you will know with accuracy that the capacitor is fully charged. CAUTION!! During charging, the resistor will become hot. This is normal, but exercise caution during the charging process. After charging is complete, remove the resistor from the incoming positive cable, and IMMEDIATELY connect it to the positive terminal of the capacitor. General Features: 3 Farad Digital Capacitor With 3000 Watts Runs On 10-16 Volts DC Audible Warning Tone for Reverse Polarity, Voltage Overload, and Low Battery Voltage Capacitance: 3,000,000, Capacitance Tolerance: + / - 10%, Voltage Measurement Accurate To + / - 0.1 VDC Equivalent Series Resistance: 0.00195 Mw @ 120 Hz / 25°C You May Also Hook Up as Many as You Like in Parallel to Make a Bank of Power Stabilizing Amplifier Flow Capacity High Strength Cylindrical Aluminum Housing Soft Turn-On/Off Power Surge Bright Charging Status L.E.D. Digital Over-Voltage Protection System Perfect for Systems Up to 3000W Max Increases Level of Bass, And the Peak Power of Your Amp Features Audible Warning Indicators Runs On 10-16 Volts Dc Equipped with Automatic Shutoff Protection Accepts Any Gauge of Wire with Ring Terminals 3 Farad Digital Power Capacitor 24 Volts Surge Ultra-Low ESR (Super Low Internal Resistance ) 3 Digit Bright Red Digital Led Voltage Display Audible Warning Tone for Reverse Polarity, Voltage Overload, And Low Battery Voltage Capacitance: 3,000,000 Capacitance Tolerance: + / - 10%, Voltage Measurement Accurate To + / - 0.1 VDC Working Voltage: 10-16 VDC, Automatic Shutoff Protection Includes Clear Mounting Brackets Includes the Resistor for Charging Reduce or Stop the Dimming of Your Headlights Accepts any gauge of wire with ring terminals Width of Mounting Bracket Base: 5-1/2" Dimensions: 11-3/4"H X 3-1/2"W X 3-1/2"D 3 Year Warranty Equivalent Series Resistance: You May Also Hook Up as Many as You Like in Parallel to Make A Bank of Power. ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

NATIONWIDE DELIVERY

At Absolute Pro Music, we are glad to ship to most countries! Check our list.

SECURE SHOPPING

We takes credit card information security seriously, we have implemented a variety of technical and procedural controls to ensure transactions on our site remain private and protected.

SHOP WITH CONFIDENCE

Absolute Pro Music wants to make sure that you are completely satisfied. If for some reason you aren't happy with product(s) and want to return it, we make returns simple.

HELP CENTER

You can simply give us a call at +1 800.674.27.24 , and our support staff will answer your call immediately! Explain your issue, what you'd like to change, or what you'd like to add onto your phone system, and get help in real time.
Absolute Pro Music
American Express Apple Pay Diners Club Discover Meta Pay Google Pay Mastercard PayPal Shop Pay Venmo Visa