Alpine (911)

Alpine Type-X Bundle 2-Pair X-S65 6.5" Coax, X-A70F 700W 4-Ch Amp, and Absolute KIT4 4 Gauge Amp Wiring Kit Alpine Type-X Bundle 2-Pair X-S65 6.5" Coax, X-A70F 700W 4-Ch Amp and Wiring - This bundle includes a pair of Alpine X-S65C X-Series 6.5 Inch Component 2-Way Speakers, a pair of Alpine X-S65 X-Series 6.5 Inch Coaxial 2-Way Speakers, an Alpine X-A70F X-Series 4/3/2 Channel Power Density Amplifier, a wiring kit, a pry kit, and an Alpine cozy. Alpine X-S65 X-Series 6.5 Inch Coaxial 2-Way SpeakersSPECIFICATIONSWoofer: 6-1/2" coneTweeter: 1" Carbon GraphiteMaximum Peak Power: 330 WattsMaximum RMS Power: 110 Wattsimpedance: 4 ohmsSensitivity: 89 dB SPL (1W @ 1m)Frequency Response: 55 Hz to 50 kHzMounting Depth/Drop-in Mounting: 2-5/16- (5.9cm)Cutout Diameter: 5-13/32- (13.7cm) circleRecommended Amplification: up to 110 watts RMS per channelWarning: Both products contain a high-performance tweeter. If there is a tweeter already installed in your car, then you must disconnect its terminals. If you leave the original tweeter connected and connect this product in parallel, then a fault may develop in this product, so you are strongly recommended not to do so. Alpine X-A70F 700 W RMS X-Series Class-D 4-Channel 2 ohm Stable AmplifierAlpine introduces the all-new X-Series of high-grade speakers and amplifiers. These products have been engineered and tuned to create a perfect match for extraordinarily dynamic, realistic sound reproduction, and a spatial sound impression.The all-new X-Series amplifiers set a new standard for sound quality performance and power output in a very compact design. Available in mono, four-channel, and five-channel configuration, these amps are a perfect match for the all-new X-Series speakers and subwoofers.General Features: Alpine X-Series X-A70F Class-D Full Range 2 ohm Stable 4-Channel Amplifier RMS Power Rating: 4 ohms: 120 watts x 4 Channel 2 ohms: 175 watts x 4 Channel 1 ohm: ------------N/A----------- Bridged, 4 Ohms: 350 Watts X 2 Channel Total power output: 700 watts CEA-2006 Compliant Amplifier Hi-Res Audio compatible Wired remote level control, Alpine RUX-KNOB.2, available Included plastic covers available to offer a brushed aluminum finish around the edges LED power (green) and protect (red) indicators Soft start turn-on 4/3/2 channel operation Speaker-level (high-level) inputs Preamp Outputs 3-way protection circuitry (thermal, overload, and speaker short protection) Dual speaker terminals simplify the hookup of multiple speakers Heavy-duty aluminum alloy heat-sink Input sensitivity High level: .4 - 10V Low level: .1 - 4V Frequency Response: 10 - 60,000 Total Harmonic Distortion (THD): .07% Signal to Noise Ratio: >106dB Variable low-pass filter: 50 - 400Hz, -24dB/octave Variable subsonic filter: 50 - 40Hz, -24dB/octave Variable Bass Boost: 0 to +12 dB bass boost at 50 Hz Fuse Rating: 35A x 3 4 gauge power and ground wiring are recommended for installation. Contact us for information regarding a discount on select amplifier kits from our website when purchased together with this amplifier. Dimensions: 11-3/4"W x 7-5/8"L x 2"H Authorized Dealer 1-year Manufacturer's Warranty What is in the X-A70M package: 4-Channel amplifier Two 35A ATO fuses (installed) Terminal Cover Left Terminal Cover Right Terminal Cover Front Battery connector plug 2 Speaker connector plugs Logo Plate (self-adhesive) 4 Self-tapping screws (Length 3/4") 2mm Allen wrench 4mm Allen wrench Owner's Manual Alpine Verification Certificate Limited Warranty To Customers sheet X-A70M owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine Type-X Bundle 2-Pair X-S65 6.5" Coax, X-A70F 700W 4-Ch Amp, and Absolute KIT4 4 Gauge Amp Wiring Kit Alpine Type-X Bundle 2-Pair X-S65 6.5" Coax, X-A70F 700W 4-Ch Amp and Wiring - This bundle includes a pair of Alpine X-S65C X-Series 6.5 Inch Component 2-Way Speakers, a pair of Alpine X-S65 X-Series 6.5 Inch Coaxial 2-Way Speakers, an Alpine X-A70F X-Series 4/3/2 Channel Power Density Amplifier, a wiring kit, a pry kit, and an Alpine cozy. Alpine X-S65 X-Series 6.5 Inch Coaxial 2-Way SpeakersSPECIFICATIONSWoofer: 6-1/2" coneTweeter: 1" Carbon GraphiteMaximum Peak Power: 330 WattsMaximum RMS Power: 110 Wattsimpedance: 4 ohmsSensitivity: 89 dB SPL (1W @ 1m)Frequency Response: 55 Hz to 50 kHzMounting Depth/Drop-in Mounting: 2-5/16- (5.9cm)Cutout Diameter: 5-13/32- (13.7cm) circleRecommended Amplification: up to 110 watts RMS per channelWarning: Both products contain a high-performance tweeter. If there is a tweeter already installed in your car, then you must disconnect its terminals. If you leave the original tweeter connected and connect this product in parallel, then a fault may develop in this product, so you are strongly recommended not to do so. Alpine X-A70F 700 W RMS X-Series Class-D 4-Channel 2 ohm Stable AmplifierAlpine introduces the all-new X-Series of high-grade speakers and amplifiers. These products have been engineered and tuned to create a perfect match for extraordinarily dynamic, realistic sound reproduction, and a spatial sound impression.The all-new X-Series amplifiers set a new standard for sound quality performance and power output in a very compact design. Available in mono, four-channel, and five-channel configuration, these amps are a perfect match for the all-new X-Series speakers and subwoofers.General Features: Alpine X-Series X-A70F Class-D Full Range 2 ohm Stable 4-Channel Amplifier RMS Power Rating: 4 ohms: 120 watts x 4 Channel 2 ohms: 175 watts x 4 Channel 1 ohm: ------------N/A----------- Bridged, 4 Ohms: 350 Watts X 2 Channel Total power output: 700 watts CEA-2006 Compliant Amplifier Hi-Res Audio compatible Wired remote level control, Alpine RUX-KNOB.2, available Included plastic covers available to offer a brushed aluminum finish around the edges LED power (green) and protect (red) indicators Soft start turn-on 4/3/2 channel operation Speaker-level (high-level) inputs Preamp Outputs 3-way protection circuitry (thermal, overload, and speaker short protection) Dual speaker terminals simplify the hookup of multiple speakers Heavy-duty aluminum alloy heat-sink Input sensitivity High level: .4 - 10V Low level: .1 - 4V Frequency Response: 10 - 60,000 Total Harmonic Distortion (THD): .07% Signal to Noise Ratio: >106dB Variable low-pass filter: 50 - 400Hz, -24dB/octave Variable subsonic filter: 50 - 40Hz, -24dB/octave Variable Bass Boost: 0 to +12 dB bass boost at 50 Hz Fuse Rating: 35A x 3 4 gauge power and ground wiring are recommended for installation. Contact us for information regarding a discount on select amplifier kits from our website when purchased together with this amplifier. Dimensions: 11-3/4"W x 7-5/8"L x 2"H Authorized Dealer 1-year Manufacturer's Warranty What is in the X-A70M package: 4-Channel amplifier Two 35A ATO fuses (installed) Terminal Cover Left Terminal Cover Right Terminal Cover Front Battery connector plug 2 Speaker connector plugs Logo Plate (self-adhesive) 4 Self-tapping screws (Length 3/4") 2mm Allen wrench 4mm Allen wrench Owner's Manual Alpine Verification Certificate Limited Warranty To Customers sheet X-A70M owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine RCA Harness Cable Connector Adapter Stereo Radio for ILXW650 ILX-W650 ILX-W650E Front/Rear/Sub-w/Rear View Camera Fitment:for ILXW650/ ILX-W650/ ILX-W650E/ ILXW650EGeneral Features: Material: Plastic Plugs directly and play High-quality plastic molded connector for the perfect fit Installation is quick and easy Perfect Fitment, direct replacement Package Includes: 1x RCA Harness Cable High-quality plastic molded connector for the perfect fit. Fitment: for ILXW650/ ILX-W650/ ILX-W650E/ ILXW650E. Features: Front/Rear/Sub-w/Front View Camera/Rear View Camera. Perfect Fitment, direct replacement, and Plugs directly and play. Package Includes: 1x RCA Harness Cable Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine KTP-445A Power Pack Head Unit Amplifier and Backup Camera Bundle. 4-Channel Compact Amp Increases Alpine Head Unit Power up to 150 Percent - 90 Watts x 4 Channels, fits iLX-W650 and Others Bundle Package: Alpine KTP-445A Power Pack Amp Absolute Waterproof Angle Backup Camera Alpine KTP-445A Plug and Play Head Unit Power Pack for Use w/ 2005-Up Alpine Head Units with a Black Power Harness The KTP-445A Power Pack amplifies power output on select 2005 and newer Alpine head units, resulting in up to a 150 percent power increase over the original power from the head unit's built-in amplifier. The compact size lets the KTP-445A fit where most amplifiers won’t. The KTP-445A comes equipped with direct plug-in connectors for select 2005 and newer Alpine head units and it fits behind the dash of most vehicles. It's small and compact at only 7-7/16” x 1-1/2” x 2-1/2”. Its size and flexible wires make the Power Pack an easy choice to save space. To ensure that Alpine sound quality is heard, we’ve created a platform that offers an unbelievably low noise floor, taking extra care to ensure a clean signal path, with no extraneous interference. The result: The Power Pack boasts a 1-watt signal-to-noise ratio of 82dB or better. General Features: Alpine Power Pack 4-Channel Class D for Select In-Dash Receivers Plug-and-play design for compatible Alpine head units (2005 - Up, Black 16 Pin) RMS Power Rating: 4 ohms: 45 watts x 4 Channel Total RMS power output: 180 watts CEA-2006 compliant amplifier Increases the output of an Alpine head unit without having to install a full-size amplifier and amp install kit The fast and easy solution to higher power aftermarket sound High-efficiency digital circuit design Gain optimized for Alpine head units Plugs directly into the wiring harness of the Alpine receiver Fast and simple installation 4-channel operation for four speakers Is not compatible with factory amplifiers Frequency response: 20-20,000 Hz Signal to Noise Ratio: 84 dBA Fuse Rating: 15A x 1 Includes both Amp-to-receiver and Amp-to-vehicle Harnesses Dimensions: 7-13/16D x 2-9/16"W x 1-1/2"H Authorized Dealer 1-year Manufacturer's Warranty What is in the KTP-445A package: Head Unit Power Pack (15A fuse installed) 39" Amp-to-receiver harness (male 16-pin connector on each end) 31" Amp-to-vehicle harness (male 16-pin connector on one end and a female 16-pin connector on the other end) 2 Brackets 4 Screws 4 Wire-ties Installation Diagram Online Product Registration Limited Warranty Information KTP-445A Power Pack owner's manual Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine KTP-445A Power Pack Head Unit Amplifier and Backup Camera Bundle. 4-Channel Compact Amp Increases Alpine Head Unit Power up to 150 Percent - 90 Watts x 4 Channels, fits iLX-W650 and Others Bundle Package: Alpine KTP-445A Power Pack Amp Absolute Waterproof Angle Backup Camera Alpine KTP-445A Plug and Play Head Unit Power Pack for Use w/ 2005-Up Alpine Head Units with a Black Power Harness The KTP-445A Power Pack amplifies power output on select 2005 and newer Alpine head units, resulting in up to a 150 percent power increase over the original power from the head unit's built-in amplifier. The compact size lets the KTP-445A fit where most amplifiers won’t. The KTP-445A comes equipped with direct plug-in connectors for select 2005 and newer Alpine head units and it fits behind the dash of most vehicles. It's small and compact at only 7-7/16” x 1-1/2” x 2-1/2”. Its size and flexible wires make the Power Pack an easy choice to save space. To ensure that Alpine sound quality is heard, we’ve created a platform that offers an unbelievably low noise floor, taking extra care to ensure a clean signal path, with no extraneous interference. The result: The Power Pack boasts a 1-watt signal-to-noise ratio of 82dB or better. General Features: Alpine Power Pack 4-Channel Class D for Select In-Dash Receivers Plug-and-play design for compatible Alpine head units (2005 - Up, Black 16 Pin) RMS Power Rating: 4 ohms: 45 watts x 4 Channel Total RMS power output: 180 watts CEA-2006 compliant amplifier Increases the output of an Alpine head unit without having to install a full-size amplifier and amp install kit The fast and easy solution to higher power aftermarket sound High-efficiency digital circuit design Gain optimized for Alpine head units Plugs directly into the wiring harness of the Alpine receiver Fast and simple installation 4 channel operation for four speakers Is not compatible with factory amplifiers Frequency response: 20-20,000 Hz Signal to Noise Ratio: 84 dBA Fuse Rating: 15A x 1 Includes both Amp-to-receiver and Amp-to-vehicle Harnesses Dimensions: 7-13/16D x 2-9/16"W x 1-1/2"H Authorized Dealer 1-year Manufacturer's Warranty What is in the KTP-445A package: Head Unit Power Pack (15A fuse installed) 39" Amp-to-receiver harness (male 16-pin connector on each end) 31" Amp-to-vehicle harness (male 16-pin connector on one end and a female 16-pin connector on the other end) 2 Brackets 4 Screws 4 Wire-ties Installation Diagram Online Product Registration Limited Warranty Information KTP-445A Power Pack owner's manual Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine KTP-445A Plug and Play Head Unit Power Pack for Use w/ 2005-Up Alpine Head Units with a Black Power Harness The KTP-445A Power Pack amplifies power output on select 2005 and newer Alpine head units, resulting in up to a 150 percent power increase over the original power from the head unit's built-in amplifier. Compact size lets the KTP-445A fit where most amplifiers won’t. The KTP-445A comes equipped with direct plug-in connectors for select 2005 and newer Alpine head units and it fits behind the dash of most vehicles. It's small and compact at only 7-7/16” x 1-1/2” x 2-1/2”. Its size and flexible wires make the Power Pack an easy choice to save space. In order to ensure that Alpine sound quality is heard, we’ve created a platform that offers an unbelievably low noise floor, taking extra care to ensure a clean signal path, with no extraneous interference. The end result: The Power Pack boasts a 1 Watt Signal-to-Noise Ratio of 82dB or better. General Features: Alpine Power Pack 4-Channel Class D for Select In-Dash Receivers Plug-and-play design for compatible Alpine head units (2005 - Up, Black 16 Pin) RMS Power Rating: 4 ohms: 45 watts x 4 Channel Total RMS power output: 180 watts CEA-2006 compliant amplifier Increases the output of an Alpine head unit without having to install a full-size amplifier and amp install kit The fast and easy solution to higher power aftermarket sound High-efficiency digital circuit design Gain optimized for Alpine head units Plugs directly into the wiring harness of the Alpine receiver Fast and simple installation 4 channel operation for four speakers Is not compatible with factory amplifiers Frequency response: 20-20,000 Hz Signal to Noise Ratio: 84 dBA Fuse Rating: 15A x 1 Includes both Amp-to-receiver and Amp-to-vehicle Harnesses Dimensions: 7-13/16D x 2-9/16"W x 1-1/2"H Authorized Dealer 1-year Manufacturer's Warranty What is in the KTP-445A package: Head Unit Power Pack (15A fuse installed) 39" Amp-to-receiver harness (male 16-pin connector on each end) 31" Amp-to-vehicle harness (male 16-pin connector on one end and a female 16-pin connector on other ends) 2 Brackets 4 Screws 4 Wire-ties Installation Diagram Online Product Registration Limited Warranty Information KTP-445A Power Pack owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine SWT-S10 1200W Max Single 10" Sealed Subwoofer Bass Tube Enclosure Combining the intense low-bass performance and ground-shaking output of the traditional Type-R subwoofers in a thin package optimized for tiny enclosures. The SWT 10” Truck Subwoofer has been engineered to offer more installation flexibility without sacrificing enormous output to build the ideal sound system for your truck. At 4-1/8” deep. These subs provide deep bass performance where it usually couldn’t fit in a truck. The vented pole optimized for a 4-1/8” deep box is the ideal enclosure size, meaning excellent bass performance can fit just about anywhere in your truck. General Features: Single 10" Sealed Subwoofer Tube Enclosure 1200 Watts MAX Power Handling 250 Watts RMS Power Handling Final Impedance: 4 ohms Preloaded with a single 10" Subwoofer Sealed enclosure with embroidered black carpet Enclosure Dimensions: 11.25"W x 23.65" D 1-year Manufacturer's Warranty Subwoofer Features: 10" Passive Subwoofer Push SPK Terminal Frequency Response: 35-200 Hz Sensitivity: 90dB Enclosure Features: Tube enclosure Black Carpet Finish with White Alpine Logo Grille included What is in the SWT-S10 package: W10S4 owner's manual One 10" Subwoofer per box Adhesive-backed foam gasket Application Guide Online product registration information Warranty Information Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine iLX-W670 7" Car Radio Stereo + TOYK983S TWH-950 install Kit & Harness for 2007-2011 Toyota Camry & Absolute CAM1800B Rear View Camera Alpine iLX-W670 7" Car Radio Stereo Apple CarPlay/Android Auto Receiver with 7" Touchscreen and Bluetooth, Double DIN General Features: digital media receiver with AM/FM tuner (does not play CDs) shallow-mount chassis design (2-13/16" deep) designed to pair with Alpine's KTA-450 power pack amplifier touchscreen swipe controls external Bluetooth microphone designed to work with Apple CarPlay and Android Auto hands-free control lets you access apps using your voice built-in Bluetooth connectivity USB port accommodates various devices and thumb drives FLAC Compatible inputs: rear USB port, two camera inputs works with SiriusXM satellite radio tuner (not included-subscription required) outputs: 6-channel preamp outputs (4-volt front, rear, subwoofer) American International TOYK983S Dash Kit Single /Double-DIN radios (Silver), TWH-950 Wire Harness Compatible Models Toyota 2007 - 2011 TOYOTA2007 - 2011 Camry (without JBL System )TOYK983S Dash Kit Single /Double-DIN radios (Silver) Painted to match the car's interior For single or double DIN car radios Durable ABS construction Gapless installation Includes storage compartment above radio for single DIN installations 2007-2011 Toyota Camry Dash Kit Silver Installation Dash Kit for Single or Double DIN Headunits Includes a storage pocket below the radio for single DIN mounting Accommodates ISO Single DIN mount Accommodates ISO Double DIN mount Gapless fit between the dash and the kit Painted to match the factory dash color Factory-matched texture style Factory look when complete Finest material for good fit and durability American International TWH-950 Wire Harness Interchange Part Number: American International TWH950, Metra 70-1761, Scosche TA02B General Features: The harness is used when installing an aftermarket stereo Connects the aftermarket stereo harness to the vehicle factory harness Designed specifically to fit the compatible vehicles Plugs into the factory harness without cutting any wires Standard color-coded wires provide a consistent and simplified installation Made from OEM quality materials Compatible with Select 1987-2008 Toyota Vehicles Metra Equivalent: Metra 70-1761 *** NOT FOR JBL OR FACTORY AMPLIFIED VEHICLES ****** For Vehicles with Silver Dash *** FITS THE FOLLOWING VEHICLES: Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine X308U 8" Car Radio Stereo + install Kit for 2007-2011 Toyota Camry & Absolute Rear View Camera Alpine X308U High-Resolution 8-Inch Mech-Less Apple Car Play & Android Auto w/Built-in 3D & 2D Navigation Touch Screen Digital Media Receiver with AM/FM Tuner General Features: Alpine X308U In-Dash Receiver CEA-2006 compliant amplifier Power Output: Peak: 50 watts x 4 channels RMS: 18 watts x 4 channels 8" Touchscreen WVGA High-Resolution Display with Swipe User Interface and Anti-Glare Screen MP3 ID3 Tag Display (Title/Artist/Album) AM/FM tuner with 18FM/12 AM presets Remote control included Keep factory controls with iDatalink® Maestro® Module 4-Way Swipe Action Control Touchscreen Alpine Connect App compatible Authorized Internet Dealer 1-year Manufacturer's Warranty Navigation Features: Quick Place Search 3D,2D, and Split-Map View Options Turn-by-turn Instructions with Text-to-Speech (TTS) Technology HERE Map Data of the USA, Canada, Alaska, Hawaii, Puerto Rico, and the Virgin Islands Latest Map Update Guarantee American International TOYK983S Dash Kit Single /Double-DIN radios (Silver), TWH-950 Wire Harness Compatible Models Toyota 2007 - 2011 TOYOTA2007 - 2011 Camry (without JBL System )TOYK983S Dash Kit Single /Double-DIN radios (Silver) Painted to match the car's interior For single or double DIN car radios Durable ABS construction Gapless installation Includes storage compartment above radio for single DIN installations 2007-2011 Toyota Camry Dash Kit Silver Installation Dash Kit for Single or Double DIN Headunits Includes a storage pocket below the radio for single DIN mounting Accommodates ISO Single DIN mount Accommodates ISO Double DIN mount Gapless fit between the dash and the kit Painted to match the factory dash color Factory-matched texture style Factory look when complete Finest material for good fit and durability American International TWH-950 Wire Harness Interchange Part Number: American International TWH950, Metra 70-1761, Scosche TA02B General Features: The harness is used when installing an aftermarket stereo Connects the aftermarket stereo harness to the vehicle factory harness Designed specifically to fit the compatible vehicles Plugs into the factory harness without cutting any wires Standard color-coded wires provide a consistent and simplified installation Made from OEM quality materials Compatible with Select 1987-2008 Toyota Vehicles Metra Equivalent: Metra 70-1761 *** NOT FOR JBL OR FACTORY AMPLIFIED VEHICLES ****** For Vehicles with Silver Dash *** FITS THE FOLLOWING VEHICLES: Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine X308U 8" Car Radio Stereo + install Kit for 2007-2011 Toyota Camry Alpine X308U High-Resolution 8-Inch Mech-Less Apple Car Play & Android Auto w/Built-in 3D & 2D Navigation Touch Screen Digital Media Receiver with AM/FM Tuner General Features: Alpine X308U In-Dash Receiver CEA-2006 compliant amplifier Power Output: Peak: 50 watts x 4 channels RMS: 18 watts x 4 channels 8" Touchscreen WVGA High-Resolution Display with Swipe User Interface and Anti-Glare Screen MP3 ID3 Tag Display (Title/Artist/Album) AM/FM tuner with 18FM/12 AM presets Remote control included Keep factory controls with iDatalink® Maestro® Module 4-Way Swipe Action Control Touchscreen Alpine Connect App compatible Authorized Internet Dealer 1-year Manufacturer's Warranty Navigation Features: Quick Place Search 3D,2D, and Split-Map View Options Turn-by-turn Instructions with Text-to-Speech (TTS) Technology HERE Map Data of the USA, Canada, Alaska, Hawaii, Puerto Rico, and the Virgin Islands Latest Map Update Guarantee American International TOYK983S Dash Kit Single /Double-DIN radios (Silver), TWH-950 Wire Harness Compatible Models Toyota 2007 - 2011 TOYOTA2007 - 2011 Camry (without JBL System )TOYK983S Dash Kit Single /Double-DIN radios (Silver) Painted to match the car's interior For single or double DIN car radios Durable ABS construction Gapless installation Includes storage compartment above radio for single DIN installations 2007-2011 Toyota Camry Dash Kit Silver Installation Dash Kit for Single or Double DIN Headunits Includes a storage pocket below the radio for single DIN mounting Accommodates ISO Single DIN mount Accommodates ISO Double DIN mount Gapless fit between the dash and the kit Painted to match the factory dash color Factory-matched texture style Factory look when complete Finest material for good fit and durability American International TWH-950 Wire Harness Interchange Part Number: American International TWH950, Metra 70-1761, Scosche TA02B General Features: The harness is used when installing an aftermarket stereo Connects the aftermarket stereo harness to the vehicles factory harness Designed specifically to fit the compatible vehicles Plugs into the factory harness without cutting any wires Standard color-coded wires provide a consistent and simplified installation Made from OEM quality materials Compatible with Select 1987-2008 Toyota Vehicles Metra Equivalent: Metra 70-1761 *** NOT FOR JBL OR FACTORY AMPLIFIED VEHICLES ****** For Vehicles with Silver Dash *** FITS THE FOLLOWING VEHICLES: Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine INE-W987HD Car Radio Stereo + install Kit for 2007-2011 Toyota Camry Alpine INE-W987HD 7" Digital Media Double DIN Bluetooth Car Stereo with Built-in 2D/3D GPS Navigation, Apple CarPlay, & Android Auto General Features: Alpine INE-W987HD In-Dash Receiver CEA-2006 compliant amplifier Power Output: Peak: 50 watts x 4 channels RMS: 18 watts x 4 channels 7" Touchscreen WVGA High-Resolution Display with Swipe User Interface and Anti-Glare Screen MP3 ID3 Tag Display (Title/Artist/Album) AM/FM tuner with 18FM/12 AM presets 1 HDMI input and 1 HDMI output Keep factory controls with iDatalink® Maestro® Module 4-Way Swipe Action Control Touchscreen Alpine Connect App compatible Built-In Digital HD Radio® Authorized Internet Dealer 1-year Manufacturer's Warranty Navigation Features: Quick Place Search 3D,2D and Split-Map View Options Turn-by-turn Instructions with Text-to-Speech (TTS) Technology HERE Map Data of the USA, Canada, Alaska, Hawaii, Puerto Rico, and the Virgin Islands Latest Map Update Guarantee American International TOYK983S Dash Kit Single /Double-DIN radios (Silver), TWH-950 Wire Harness Compatible Models Toyota 2007 - 2011 TOYOTA2007 - 2011 Camry (without JBL System )TOYK983S Dash Kit Single /Double-DIN radios (Silver) Painted to match the car's interior For single or double DIN car radios Durable ABS construction Gapless installation Includes storage compartment above radio for single DIN installations 2007-2011 Toyota Camry Dash Kit Silver Installation Dash Kit for Single or Double DIN Headunits Includes a storage pocket below the radio for single DIN mounting Accommodates ISO Single DIN mount Accommodates ISO Double DIN mount Gapless fit between the dash and the kit Painted to match factory dash color Factory matched texture style Factory look when complete Finest material for good fit and durability American International TWH-950 Wire Harness Interchange Part Number: American International TWH950, Metra 70-1761, Scosche TA02B General Features: Harness is used when installing an aftermarket stereo Connects the aftermarket stereo harness to the vehicles factory harness Designed specifically to fit the compatible vehicles Plugs into the factory harness without cutting any wires Standard color coded wires provide a consistent and simplified installation Made from OEM quality materials Compatible with Select 1987-2008 Toyota Vehicles Metra Equivalent: Metra 70-1761 *** NOT FOR JBL OR FACTORY AMPLIFIED VEHICLES ****** For Vehicles with Silver Dash *** FITS THE FOLLOWING VEHICLES: ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov