Alpine (870)

Alpine S-W12D4 1800W Max (600W RMS) 12" Type-S Series Dual 4 Ohm Car Subwoofer VERSATILE APPLICATIONS Along with the new 8” woofer, the 10” and 12” S-Series subwoofers have been re-designed from the ground up. The mounting depth of the 10” and 12” subwoofers are almost 1” more shallow than previous models at just over 4.5” for the 10” models and just over 5” for the 12” models, allowing them to fit into a wide variety of installation applications. General Features: 12" 4 Ohm Type-S Series Subwoofer Power Handling: Peak: 1800 watts RMS: 600 watts Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 5-1/16" Cutout diameter: 10-9" Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 31 Hz Authorized Dealer 1-year Manufacturer's Warranty What is in the S-W12D4 package: Alpine S-W12D4 owners manual One 12" Dual 4-ohm voice coil subwoofer Two 3" jumper cables Subwoofer Application Guide Online product registration information Warranty Information ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine S-W10D2 1800W Max (600W RMS) 10" S-Series Dual 2 Ohm Car Subwoofer Alpine introduces the all-new S-Series Subwoofers; their unique design substantially improves bass output and provides installation versatility. Each S-Series subwoofer uses a custom-stamped steel frame and is available in twelve, ten, and eight-inch. These high-strength frames were designed to withstand the rigors of the improved S-Series motor. They have frame leg vents, a vented back plate to help cool the subwoofer voice coil and motor parts, and a shallow design to help fit in smaller spaces. The S-Series Subwoofers incorporate two strontium ferrite magnets stacked together, providing increased motor strength and excursion, ultimately delivering an accurate bass to your music. The convenient push-type insert terminals with a dual voice coil jumper system will significantly reduce installation time. Just strip the speaker insulation at the wire end, then insert the bare wire into the hole of the spring-loaded push terminal. At the same time, the concealed mount gasket system creates a clean, finished appearance for any vehicle. General Features: 10" 2 ohm S-Series (Type-S) Subwoofer RMS Power Handling: 600 watts Peak Power Handling: 1800 watts  Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 4-11/16" Cutout diameter: 8-13/16 Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 33 Hz Authorized Dealer 1-year Manufacturer's Warranty What is in the S-W10D2 package: S-W10D2 owner's manual One 10" Dual 2-ohm voice coil subwoofer 1 Rubber concealing ring Two 3" jumper cables (each has a single banana connector on each end) Subwoofer Application Guide Online product registration information Warranty Information ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

                                  Alpine R2-W10D4 2250W Max (750W RMS) 10" R-Series Dual 4-Ohm Car Subwoofer The new R-Series subwoofers take a great platform to the next level. Although the R-Series subwoofers are new for 2017, they come from an impressive Alpine lineage – the Type-R subwoofers. Type-R subwoofers have been known for their power handling, clean output, and deep bass excursion at a mid-line price. Using the highly successful Type-R subwoofers as a foundation, we applied various performance and hardware improvements to the design, fundamentally transforming them into the new R-Series subwoofers – The Next Evolution of Proven Performance. STRONGER CONE ASSEMBLYR-Series subwoofers feature a Kevlar-treated cone for durability. This cone and the Santoprene surround allow the subwoofer to deliver 19mm X-max for incredible, hard-hitting bass. A new method of attaching the spider and cone to the voice coil ensures rigidity throughout the motor structure and increases the subwoofer's accuracy. MORE RIGID DUST CAP Talc, a common mineral used in products such as baby powder and paint, has been found to have incredible damping properties while being less dense than the traditional Mica filler used in dust caps. By adding a calculated amount of talc to the mica polypropylene in the dust cap, we increased the cap's vibration absorption while lowering its density. The lighter dust cap contributes to a faster attack and a more accurate reproduction of low frequencies. NEW POWER RATING All four R-Series subwoofers are rated at 750W RMS. They perfectly match the PDR-M65 Mono Power Density Amplifier, creating an efficient system. General Features: 10" Dual 4 ohm Type-R Subwoofer Peak Power Handling: 2250 watts RMS Power Handling: 750 watts Recommended power range: 300 - 750W RMS CTA-2031 compliant power ratings Parabolic pulp/kevlar cone H.A.M.R. surround Polypropylene, mica, and talc dust cap Reinforced cone neck and spider joint Cast aluminum frame with integral shorting sleeve 8AWG push terminals with VC configuration jumpers 2.6" High excursion overhung voice coil 111 oz. Strontium ferrite segmented magnet Top-mount depth: 5-7/8" Cutout diameter: 9-1/16" Frequency Response: 26 - 200Hz Sensitivity: 82.4dB Resonance Frequency (Fs): 30Hz Authorized Dealer 1-year Manufacturer's Warranty What's in the R2-W10D4 package: R2-W10D4 owner's manual 10" Dual 4-ohm voice coil subwoofer 1 Rubber concealing ring  Four 3" jumper cables  R-Series Subwoofer Application Guide Online product registration information Warranty Information Important Notice! Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca. https://www.alpine-usa.com/product/r-series-subwoofer-r2w10d4 https://www.youtube.com/watch?v=J8g6EZzZQyI&t=131s

Alpine R2-W12D2 2250W Max (750W RMS) 12" R-Series Dual 2-Ohm Car Subwoofer The new 2022 R-Series subwoofers are here - drawing from decades of Subwoofer engineering experience. They deliver deep, clean, accurate bass and feature Alpine’s HAMR Surround for maximum cone excursion, delivering tons of bass output. The new ceramic dust cap is very lightweight and rigid, keeping distortion an absolute minimum. The enlarged motor structure ensures better overall woofer control for a clean, strong bass response. General Features: 12" Dual 2 ohm Type-R Subwoofer Peak Power Handling: 2250watts RMS Power Handling: 750 watts Recommended power range: 300 - 750W RMS CTA-2031 compliant power ratings Parabolic pulp/kevlar cone H.A.M.R. surround Polypropylene, mica, and talc dust cap Reinforced cone neck and spider joint Cast aluminum frame with integral shorting sleeve 8AWG push terminals with VC configuration jumpers 2.6" High excursion overhung voice coil 127 oz. Strontium ferrite segmented magnet Top-mount depth: 6-3/8" Cutout diameter: 10-7/8" Frequency Response: 24 - 200Hz Sensitivity: 84.3dB Resonance Frequency (Fs): 27Hz Authorized Dealer 1-year Manufacturer's Warranty What's in the R2-W12D2 package: R2-W12D2 owner's manual One 12" Dual 2-ohm voice coil subwoofer Two 3" jumper cables R-Series Subwoofer Application Guide Online product registration information Warranty Information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine R2-W12D4 2250W Max (750W RMS) 12" R-Series Dual 4-Ohm Car Subwoofer The new 2022 R-Series subwoofers are here - drawing from decades of Subwoofer engineering experience. They deliver deep, clean, accurate bass and feature Alpine’s HAMR Surround for maximum cone excursion, delivering tons of bass output. The new ceramic dust cap is lightweight and rigid, keeping distortion at an absolute minimum. The enlarged motor structure ensures better woofer control for a strong, clean bass response. General Features: 12" Dual 4 ohm Type-R Subwoofer Peak Power Handling: 2250watts RMS Power Handling: 750 watts Recommended power range: 300 - 750W RMS CTA-2031 compliant power ratings Parabolic pulp/kevlar cone H.A.M.R. surround Polypropylene, mica, and talc dust cap Reinforced cone neck and spider joint Cast aluminum frame with integral shorting sleeve 8AWG push terminals with VC configuration jumpers 2.6" High excursion overhung voice coil 127 oz. Strontium ferrite segmented magnet Top-mount depth: 6-3/8" Cutout diameter: 10-7/8" Frequency Response: 24 - 200Hz Sensitivity: 84.3dB Resonance Frequency (Fs): 27Hz Authorized Dealer 1-year Manufacturer's Warranty What's in the R2-W12D4 package: R2-W12D2 owner's manual One 12" Dual 4-ohm voice coil subwoofer Two 3" jumper cables R-Series Subwoofer Application Guide Online product registration information Warranty Information https://www.youtube.com/watch?v=ihjWBSOYVxE&t=179s ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine KTE-S69G 6" x 9" Type-S Speaker Grilles General Features: Speaker grilles for Alpine Type-S 6" x 9" speakers Alpine S-S69 Alpine S-S69C Includes trim ring Sold as a Pair Includes metal mesh grille w/ S series logo Authorized Dealer What's in the KTE-S69G: 2 Metal mesh grilles 2 Plastic trim rings Installation Instructions Alpine KTE-S69G owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine S-S69 520W Max (170W RMS) 6" x 9" Type S Series 2-Way Coaxial Car Speakers To meet the needs of the most common applications in speaker replacement today, we've introduced a 6x9-inch component set to offer newer domestic trucks and cars the ability to upgrade the sound quality of their vehicle. With its innovative technology, this component set is a simple solution to getting Alpine sound in many of these vehicles today.   General Features: 6" x 9" Type S Series 2-Way Coaxial Car Speakers Power Handling: Peak: 520 watts per pair / 260 watts each Power Handling: RMS: 170 watts per pair / 85 watts each Recommended Power Range: 10 - 85 watts RMS per channel Carbon Fiber Reinforced Plastic (CFRP) Cone High Amplitude Multi-Roll (HAMR) Surround 1" Silk Dome Tweeter Rubber magnet boot cover CEA-2031 compliant speakers 35mm Voice Coil Top-mount Depth: 2-15/16" Cutout Dimensions: 5-29/32" x 8-3/4" 4 ohms Impedance Frequency Response: 65 - 22000 Hz Sensitivity: 90dB Compatible with the Alpine KTE-S69G Grille Authorized Dealer 1-year Manufacturer's Warranty What is in the S-S69 package: S-S69 owner's manual Two 2-way speakers 2 Bottom mount brackets Two 12" Lengths of speaker wire Eight 1-3/16" Screws Eight M4x60mm Machine screws  Eight M4 Nuts 8 Speed clips Warranty information Online product registration information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine R-S69.2 600W Peak, 200W RMS R-Series 6x9 Inch Coaxial 2-Way Speakers R-Series speakers give you power and control. With an innovative material that delivers more output, the speakers produce a dependable performance for a loud and fun experience. If you play your music loud and want others to know, the R-Series speakers are the match for you. You’ll enjoy a center sound stage with speakers that play loud and clear without distortion. The R-Series speakers are tuned with an emphasis on the high- and low-end frequencies, so they deliver power while naturally producing bright, active sound. They are the perfect power and performance match for the R-Series subwoofers and amplifiers. The woofers have a large, 35-millimeter (mm) voice coil which allows for more coil windings to fit in the gap. This results in greater heat dissipation and increased power handling, for superior control and output. General Features: Alpine R-S69.2 R-Series 6x9 Inch Coaxial 2-Way Speakers Power Handling: RMS: 100 Watts Peak: 300 Watts Impedance: 4 Ohm Carbon-fiber reinforced polymer (CFRP) woofer Carbon-fiber reinforced polymer dome tweeter Frequency response: 60 Hz - 40 kHz Sensitivity: 90 dB Top-mount depth: 2-7/8" Grilles included Authorized Dealer 1-year Manufacturer's Warranty What's in the R-S69.2 package: Two 2-way Speakers 2 Bottom mount brackets 2 Grilles 2 Grille badges Eight 1-1/8" Screws Eight M4x60mm Machine screws 8 Split lock washers 8 Flat washers Eight M4 Hex nuts 8 Speed clips Warranty information Important Notice Online product registration information Template and specs on the box R-S69.2 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine KTP-445A Plug and Play Head Unit Power Pack for Use with 2005-Up Alpine Head Units with a Black Power Harness The KTP-445A Power Pack amplifies the power output on select 2005 and newer Alpine head units, resulting in a power increase of up to 150% over the original power from the head unit's built-in amplifier. The compact size of the KTP-445A allows it to fit where most amplifiers won’t. The KTP-445A comes equipped with direct plug-in connectors for select 2005 and newer Alpine head units, and it fits behind the dash of most vehicles. It's small and compact at only 7-7/16” x 1-1/2” x 2-1/2”. Its size and flexible wires make the Power Pack an easy choice to save space. To ensure that Alpine sound quality is heard, we’ve created a platform that offers an unbelievably low noise floor, taking extra care to ensure a clean signal path with no extraneous interference. The result: The Power Pack boasts a signal-to-noise ratio of 82dB or better.  General Features: Alpine Power Pack 4-Channel Class D for Select In-Dash Receivers Plug-and-play design for compatible Alpine head units (2005 - Up, Black 16 Pin) RMS Power Rating: 4 ohms: 45 watts x 4 Channel Total RMS power output: 180 watts CEA-2006 compliant amplifier Increases the output of an Alpine head unit without having to install a full-size amplifier and amp install kit The fast and easy solution to higher power aftermarket sound High-efficiency digital circuit design Gain optimized for Alpine head units Plugs directly into the wiring harness of the Alpine receiver Fast and simple installation 4-channel operation for four speakers It is not compatible with factory amplifiers Frequency response: 20-20,000 Hz Signal to Noise Ratio: 84 dBA Fuse Rating: 15A x 1 Includes both Amp-to-receiver and Amp-to-vehicle Harnesses Dimensions: 7-13/16D x 2-9/16"W x 1-1/2"H Authorized Dealer 1-year Manufacturer's Warranty What is in the KTP-445A package: Head Unit Power Pack (15A fuse installed) 39" Amp-to-receiver harness (male 16-pin connector on each end) 31" Amp-to-vehicle harness (male 16-pin connector on one end and a female 16-pin connector on the other end) 2 Brackets 4 Screws 4 Wire-ties Installation Diagram Online Product Registration Limited Warranty Information KTP-445A Power Pack owner's manual Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine R-S65C.2 100W RMS 6.5" R-Series Component 2-Way Speakers   TURN IT UP If you play your music loud and want others to know, the R-Series speakers are the match for you. You’ll enjoy a center sound stage with speakers that play loud and clear without distortion. The R-Series speakers are tuned with an emphasis on the high- and low-end frequencies, so they deliver power while naturally producing bright, active sound. They are the perfect power and performance match for the R-Series subwoofers and amplifiers. General Features: 6.5-inch R-Series Component 2-way Car Speakers component speaker system includes two woofers, 2 tweeters, and 2 external crossovers Power Handling: Peak: 300 watts RMS: 100 watts 4 Ohms impedance Frequency response: 65Hz-40kHz Carbon Fiber Reinforced Polymer (CFRP) exclusive cone technology CFRP increases the speakers’ mid-bass performance and dynamic range CFRP is used as a tweeter diaphragm, enabling the system to perform up into the 45kHz range, making the speakers compliant with High-Resolution Audio playback Patented High-Amplitude Multi-Roll (HAMR) surround, for control and accuracy Ideal for tight installations and use matching speaker grills that are shallower as well (sold separately) Uses an in-line, passive design with a reduced footprint, which also contributes to easier installation Authorized Dealer 1-year Manufacturer's Warranty What's in the box: 2 Woofers Two 6-1/2" Adapter rings (includes GM/Chrysler) Two 6x8 Adapter rings 2 Woofer grilles 2 Grille badges 2 Tweeters (each has an attached 30" length of wire) 2 Tweeter grilles (installed) 2 Swivel flush mount housings (with tweeters installed) Two crossovers (each has attached input and output wires) 2 Flush mount retention rings 2 Stealth brackets 2 Foam self-adhesive pads 2 Foam self-adhesive rings Eight 1-1/8" Screws Eight 1/2" Screws 8 Speed-clips Eight M4x12mm Machine screws Four 5" Zip ties 2 Pieces of two-sided tape Warranty information Online product registration note Important Notice sheet Template and specs on the box Alpine R-S65C.2 owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine S-A32F S-Series 320W RMS 4-Channel Digital Class D Car Audio Amplifier The all-new S-Series amplifiers pack a punch with even more performance and value. Experience hard-hitting bass and long hours of limitless play with the S-A32F 4-channel amplifier. These amplifiers offer great value with over 20% more power through increased watt handling. The exceptional strength and resistance are supported by optimizing a heat thermal management processor to ensure exceptional reliability. You can enjoy your music with the bass cranked up for hours without any power shutdown.General Features: Alpine S-Series S-A32F 4/3/2 Channel Power Amplifier S-Series amplifiers are your sound system’s workhorse. With unmatched reliability and budget-friendly prices, these amplifiers are the better choice in performance value. S-Series Amplifier: Known for reliable performance and value-oriented products. Power Output: 55W RMS x 4 (4ohm, 14.4V ≤ 1% THD+N) 80W RMS x 4 (2ohm, 14.4V≤ 1% THD+N) Bridged: 160W RMS x 2 (4ohm, 14.4V ≤ 1% THD+N) Total power output: 320 watts CEA-2006 Compliant Amplifier LED Power/Protect Light Speaker-level (high-level) inputs 3-way protection circuitry (thermal, overload, and short speaker protection) Frequency Response: 10 - 30,0000 Hz Total Harmonic Distortion (THD): <1% Signal Noise Ratio: 83 dB Variable high-pass filter: 50 - 400 Hz, 12 dB/octave Variable low-pass filter: 50 - 400 Hz, 12 dB/octave Fuse Rating: 40 Improved heat sink and protection circuit design Contain technology currently implemented in the Alpine R and X-Series models 105dB Signal-to-Noise (S/N) ratio at rated power 46 degrees of phase shift Designed to perform perfectly with the existing S-Series speakers and subwoofers Dimensions: 8” W x 8” H x 2.25” D Authorized Dealer 1-year Manufacturer's Warranty What is in the S-A32F package: S-A32F owner's manual 4-Channel amplifier One 40-amp ATO fuse Four 3/4" Screws 2mm Allen wrench Alpine Verification Certificate Warranty information Online product registration information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine S-A55V S-Series 5-Channel Class D Amplifier 540W RMS The Alpine S-Series Sound ComponentsThree new S-Series amplifiers join the S-Series family, known for reliable performance and value-oriented products. All three S-Series amps (mono, 4-channel, and 5-channel) contain technology currently implemented in R and X-Series models. The S-Series amps feature attractive prices and are designed to perform perfectly with the existing S-Series speakers. S-Series amplifiers are your sound system’s workhorse. With unmatched reliability and budget-friendly prices, these amplifiers are the better choice in performance value. General Features: 5-channel Class D Amplifier Power Output: 40 watts RMS x 4 + 200 watts RMS x 1 at 4 ohms 60 watts RMS x 4 + 300 watts RMS x 1 at 2 ohms 120 watts RMS x 2 bridged at 4 ohms + 300 watts RMS x 1 at 2 ohms CTA-2006 compliant Variable high-pass filter (50-400 Hz, 12 dB/octave) on 4-channel section Variable low-pass filter (50-400 Hz, 24 dB/octave) on a subchannel Variable bass boost (0-12 dB at 50 Hz) on a subchannel Optional RUX-KNOB.2 wired remote level control for a subchannel Preamp and speaker-level inputs speaker wire to RCA adapter required for speaker-level input Wiring and hardware not included with amplifier 4-gauge power and ground leads recommended Fuse rating: 30A x 2 Dimensions: 11-1/4" W x 2-1/4" H x 8" D Authorized Dealer 1-year Manufacturer's Warranty What's in the box: 5-Channel amplifier Two 30-amp ATO fuses (installed) Four 3/4" Screws 2mm Allen wrench Owner's manual (English/ French/ Spanish) Alpine Verification Certificate Warranty information Power supply note Online product registration information Alpine S-A55V owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov