Alpine (870)

Alpine RUX-KNOB.2 Remote Bass Knob for Alpine Amplifiers General Features: Remote Bass Level Control Knob 16-1/2" (5 meters) Connection cable Plugs directly in for quick, direct subwoofer control Specifically designed as the controller for use with any of the following PDX Amplifiers: PDX-M12 and PDX-M6 Easily adjust the bass gain of your amp while seated inside Control multiple amps from just one RUX-KNOB controller Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the package: Alpine Remote Bass Level Control module 16.4'  connecting cable  4 Self-tapping screws Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine KTA-30FW 600W Max, 300W RMS KTA Series 4 ohm Stable 4-Channel Class-D Tough Power Pack Amplifier Half The Size, Double The Power Get a huge increase in sound performance over your factory system. With Alpine’s exclusive technology, Dynamic Peak Power (D.P.P.), the KTA-30FW Weather Resistant Tough Power Pack is sure to add higher output and increased dynamic range for those open cab vehicles and toys. The KTA-F30W is perfect for when you want to boost your sound system but don’t have space for a large amplifier. It is compatible with an aftermarket or factory head unit and adds up to 4 times the power over the head unit's original built-in power. The KTA-30FW is ready for your adventures. It is weather-resistant, rated at IP66 for protection against dust ingress and high-pressure water spray. The KTA-30FW features a rugged chassis and high-quality waterproof connector so it can be used in installations where it will be exposed to the elements, like side-by-sides, boats, open-top vehicles. and motorcycles. General Features: Alpine KTA-30FW Class-D Full Range 4-Ohm Stable 4-Channel Amplifier Designed for use in Side-by-Sides, Boats, Open-Top Vehicles, and Motorcycles RMS Power Rating: 4 ohms: 75 watts x 4 Channel RMS Power Rating: 2 ohms: 75 watts x 4 Channel 150 watts RMS x 2 bridged at 4 ohms (4-ohm stable in bridged mode) Total power output: 600 watts CEA-2006 Compliant Amplifier Power Wire Harness Included Pulse Width Modulated MOSFET power supply Wired remote bass level control included Soft start turn-on Switchable 4 or 2 channel operation Speaker-level (high-level) inputs Preamp RCA outputs to daisy chain multiple amps 3-way protection circuitry (thermal, overload, and speaker short protection) Dual speaker terminals simplify the hookup of multiple speakers Heavy-duty aluminum alloy heat-sink IP66 Waterproof Rating Input sensitivity: Low level: 0.2V-4V Input sensitivity: High level: 0.5V-10V Frequency Response: 15 - 36000 Hz Total Harmonic Distortion (THD): <0.1% Signal to Noise Ratio: >98 dB Variable high-pass filter: 50 - 400 Hz, 12 dB/octave Variable low-pass filter: 50 - 400 Hz, 12 dB/octave Variable Bass Boost: 0 to +12 dB bass boost at 50 Hz Dimensions: 9-3/16"W x 3-3/4"D x 1-3/4"H Authorized Dealer 1-year Manufacturer's Warranty What is in the box: 4-Channel amplifier 14" Power/signal harness (26-pin connector on one end and bare wires + RCAs on other ends) 4 Self-tapping screws (Length 3/4") Connection sheet Limited Warranty sheet Thank you letter Alpine KTA-30FW Tough Power Pack owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine SWT-10S4 1000W Peak 10" SWT Series Single 4-ohm Shallow Mount Subwoofer Right size, Right sound. Here's a big bass breakthrough for truck lovers. Alpine engineered their SWT-10S4 10" subwoofer to go behind your seat and sound especially good in the limited space of a truck cab. This deep-sounding, high-performance sub works well in shallow enclosures that'll fit behind or under the seat in your truck. A "high amplitude" surround allows more cone travel than a regular sub, so the SWT-10S4 can push more air and play louder. Airflow-insured subs get hot as they play, and the heat usually gets vented away via a port in the back of the sub's pole piece. Alpine recessed the pole port and added cooling air vents on the sides of the frame, allowing you to use an enclosure with an inside clearance of as little as 4-3/16" without blocking critical airflow. General Features: 10" SWT Series Single 4-ohm Shallow Mount Truck Subwoofer Peak Power Handling: 1,000 watts RMS Power Handling: 350 watts Recommended Power Range: 100W - 350W Poly-Mica Dust Cap & Pulp-Kevlar Polyurethane Foam Surround H.A.M.R. Surround Technology Spiral Cut Aluminum Former 65mm Voice Coil with High-Temp 4-Layer SVC Winding 8AWG Push Terminals Top-mount depth: 4-3/16" Mounting Diameter: 8-15/16'' Frequency Response: 30 - 200 Hz Sensitivity: 84.8 dB Authorized Dealer 1-year Manufacturer's Warranty What is in the SWT-10S4 package: SWT-10S4 owner's manual 10" Thin-mount subwoofer Online product registration information Warranty information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine PWE-S8 120W Compact Powered 8" Car Subwoofer for Under or Behind the Seat Its super shallow structure makes it ideal for under-seat installation or in small spaces. The compact, 120W PWE-S8 amplified subwoofer system lets you add deep, accurate bass to your sound system without taking up much space in your vehicle. General Features: 120W Compact Powered 8" Car Subwoofer Peak Power Handling: 240 watts RMS Power Handling: 120 watts 8" woofer high-excursion cone built-in Class D amplifier frequency response: 32-150 Hz variable low-pass crossover (80-200 Hz) variable phase control (0-180 degrees) preamp- and speaker-level inputs Dimensions: 13-1/2"W x 3"D x 9"H Authorized Dealer 1-year Manufacturer's Warranty What's in the PWE-S8 package: PWE-S8 owner's manual Amplified enclosure with one 8" subwoofer installed 12" Wiring harness Two 15 amp ATO fuses Remote level control with 15' cable attached Adhesive-backed hook and loop mounting fasteners 4 Mounting brackets Eight 5/8" Pan head self-tapping screws Eight M4x7.5mm Machine screws Warranty information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine KTA-30MW Car Amplifier Mono 300-Watt RMS Weather-Resistant Tough Power Pack Amplifier A TOUGH MINI AMP THAT PACKS A PUNCH Get big amp performance in a compact, resilient package. With Alpine’s exclusive technology, Dynamic Peak Power (D.P.P.), the KTA-30MW Weather-Resistant Tough Power Pack is sure to deliver powerful bass output for subwoofers used in those open cab vehicles and toys. This small and efficient amplifier can be installed with an aftermarket or factory head unit while adding up to 600 watts of D.P.P. power. Its weather resistance makes the KTA-30MW a good choice for use in exposed installations like side-by-sides, boats, open-top vehicles, and motorcycle saddlebags. A SOUND SYSTEM BOOST WITHOUT THE BIG SPACE COMMITMENT The KTA-30MW is perfect for when you want to add subwoofer power but don’t have space for a large amplifier. It is compatible with an aftermarket or factory head unit and provides up to 600 DPP watts to the subwoofer of your choice. HALF THE SIZE OF OUR SMALLEST TRADITIONAL AMPLIFIERS The KTA-30MW measures just 9-3/16” (W) x 1-5/8” (H) x 3-3/4” (D), so its small footprint lets it fit where most amplifiers won’t, like under the dash or in the glove compartment, installed under the dash of a side-by-side, placed in the saddlebag of a motorcycle, or used in other places where space is an issue. General Features: Alpine KTA-30MW Class D Monoblock Weather-Resistant Power Pack Amplifier 300 Watts RMS X 1 @ 4 Ohms Power Handling 600 Watts RMS X 1 @ 2 Ohms Power Handling CTA-2006 compliant Frequency Response: 20-400 Hz Total Harmonic Distortion (THD): <1% Signal to Noise Ratio: 83dB Variable Low Pass filter 50-400Hz @ -24dB/Oct. Variable Bass Boost (0-12 dB at 50 Hz) Fuse Rating: 25A Weather-resistant (IP66 rating) Dynamic Peak Power (D.P.P.) technology intelligently adjusts the gain to adapt to musical needs automatically Dimensions: 7” W x 3.5” H x 1.25” D Authorized Dealer 1-year Manufacturer's Warranty What is in the KTA-30MW box: Mono amplifier 14" Power/signal harness (26-pin connector on one end and bare wires + RCAs on the other ends) 4 Self-tapping screws (Length 3/4") Connection sheet Limited Warranty sheet KTA-30MW owner's manual Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

  Alpine Halo R2-SB10V 750W RMS 10" Halo Series Linkable Ported Loaded Subwoofer Enclosure A subwoofer enclosure that sounds as good as it looks. Alpine’s preloaded, linkable subwoofer enclosures deliver powerful performance with the unique Alpine Halo design and ProLink technology. The new 2nd generation R-Series subwoofers take bass performance to extreme levels, delivering thunderous, ground-pounding bass. With Alpine’s enhanced sound performance, the R-Series subwoofers are highly accurate, creating a perfectly matched sound system for R-Series amplifiers and speakers – building an overall cohesive theme with its entire full-range Hi-RES Audio certified system. The R2-SB10V is designed for amplifier compatibility with 20hm loads. General Features: Dual 10" Vented / Ported Subwoofer Enclosure Power Handling: Peak: 2250 watts Total RMS: 750 watts Total Preloaded with single 10" Subwoofers Vented / Ported Square/Rectangle enclosure Enclosure Dimensions: 14.5" TD x BD x 16" W x 12.68" H Groundbreaking Alpine Halo Design ProLink™ ported enclosure design Optimal Sound Performance Includes preloaded R-W10D4 10” R-Series subwoofer CARB-compliant 3/4-inch MDF construction Premium black carpet Silver Alpine embossed side logo badge Brushed aluminum finished metallic front baffle Authorized Internet Dealer 1-year Manufacturer's Warranty Subwoofer Features: Frequency Response: 24 - 200 Hz Sensitivity: 85 dB Enclosure Features: 10" Square/Rectangle Enclosure Box Finish: Carpet What's in the R2-SB10V package: R2-SB10V Owner's manual Ported enclosure loaded with one R2-W10D4 subwoofer driver Warranty information Product registration information Safety notice Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine W12S4 12" BassLine Series 12" 750W Max (250W RMS) 4-ohm Bass Subwoofer Legendary Alpine quality at an affordable priceCar audio enthusiasts know that Alpine is the leader in technology and innovation. Their reputation for developing the most reliable products is legendary. The BassLine product line is their quest to give customers a quality product that won't break the bank.The surround and wattage match made in heaven.The 250 watts of continuous power that the W12S4 handles complements the poly-foam surround that Alpine went with. It provides the best sound quality money can buy at this price point.General Features: 12-inch single 4Ω subwoofer Polypropylene and mica cone with poly-foam surround Peak Power Handling: 750 watts RMS Power Handling: 250 watts Recommended power range: 50W - 250W RMS Polypropylene-Mica cone High-excursion poly-foam surround Progressive Wavelit Ribs (P.W.R.) cone design Frequency Response: 32Hz-200Hz 5-5/16-inch mounting depth Recommended Sealed box volume: 1.09 Cu. Ft. Recommended Ported box volume: 1.91 Cu. ft Bass For All High-strength custom steel frame 8AWG push terminals 2" voice coil 52oz. magnet Recommended Box Volume: 0.5-1.5 Cu. ft.3 Top-mount depth: 5-5/16" Cutout diameter: 10-5/8" Frequency Response: 22 - 200Hz Sensitivity: 87.9dB Resonance Frequency (Fs): 30 Performance: Efficiency & Tight Bass An optimized magnet circuit allows more focused magnetism in the gap, improving efficiency. This means tighter bass control and more output! What's in the W12S4 package: One 12" Subwoofer Adhesive-backed foam gasket Application Guide Online product registration information Warranty information Important Notice! W12S4 owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine S-W8D4 900W Max (300W RMS) 8" Type S Series Dual 4 Ohm Car Subwoofer ADD BASS TO PRACTICALLY ANY VEHICLE Don’t think you have room for a subwoofer? Think again. The new S-W8D2 and S-W8D4 8” S-Series subwoofers have a shallow mounting depth of just 3-3/4” and can be used in a sealed box enclosure as small as .15 cubic feet. It is perfect for under-seats, behind rear bench seats in trucks, or even in some door applications. General Features: 8" 4 Ohm Type S Series Subwoofer Power Handling: Peak: 900 watts RMS: 300 watts Recommended Power Range: 150 - 300 Watts Kevlar Reinforced Pulp Cone HAMR Santoprene Rubber Surround Progressive Spider with Reinforced Layer Tinsel Leads Compound Radius Curve Extended Pole Geometry Perimeter Vented Frame with Airflow Management System 10 AWG Push Terminals 35mm Underhung Voice Coils Concealed Mount Gasket 34oz Ferrite Magnet Top-mount depth: 3-3/4" Cutout diameter: 6-7/8" Frequency Response: 34-200Hz Authorized Dealer 1-year Manufacturer's Warranty Priced Individually What's in the S-W8D4 package: 8" Dual 4-ohm voice coil subwoofer Alpine S-W8D4 owner's manual 1 Rubber concealing ring Two 3" jumper cables Subwoofer Application Guide Online product registration information Warranty information  Important Notice!  ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine R2-W10D2 2250W Max (750W RMS) 10" R-Series Dual 2-Ohm Car Subwoofer The new R-Series subwoofers take a great platform to the next level. Although the R-Series subwoofers are new for 2017, they come from an impressive Alpine lineage – the Type-R subwoofers. Type-R subwoofers have been known for their power handling, clean output, and deep bass excursion at a mid-line price. Using the highly successful Type-R subwoofers as a foundation, we applied various performance and hardware improvements to the design, fundamentally transforming them into the new R-Series subwoofers – The Next Evolution of Proven Performance. STRONGER CONE ASSEMBLYR-Series subwoofers feature a Kevlar-treated cone for durability. This cone and the Santoprene surround allow the subwoofer to deliver 19mm X-max for incredible, hard-hitting bass. A new method of attaching the spider and cone to the voice coil ensures rigidity throughout the motor structure and increases the subwoofer's accuracy. MORE RIGID DUST CAP Talc, a common mineral used in products such as baby powder and paint, has been found to have incredible damping properties while being less dense than the traditional Mica filler used in dust caps. By adding a calculated amount of talc to the mica polypropylene in the dust cap, we increased the cap's vibration absorption while lowering its density. The lighter dust cap contributes to a faster attack and a more accurate reproduction of low frequencies. NEW POWER RATING All four R-Series subwoofers are rated at 750W RMS. They perfectly match the PDR-M65 Mono Power Density Amplifier, creating an efficient system. General Features: 10" Dual 2 ohm Type-R Subwoofer Peak Power Handling: 2250watts RMS Power Handling: 750 watts Recommended power range: 300 - 750W RMS CTA-2031 compliant power ratings Parabolic pulp/kevlar cone H.A.M.R. surround Polypropylene, mica, and talc dust cap Reinforced cone neck and spider joint Cast aluminum frame with integral shorting sleeve 8AWG push terminals with VC configuration jumpers 2.6" High excursion overhung voice coil 111 oz. Strontium ferrite segmented magnet Top-mount depth: 5-7/8" Cutout diameter: 9-1/16" Frequency Response: 26 - 200Hz Sensitivity: 82.4dB Resonance Frequency (Fs): 30Hz Authorized Dealer 1-year Manufacturer's Warranty What's in the R2-W10D2 package: R2-W10D2 owner's manual 10" Dual 2-ohm voice coil subwoofer 1 Rubber concealing ring  Four 3" jumper cables  R-Series Subwoofer Application Guide Online product registration information Warranty Information Important Notice! Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca. https://www.alpine-usa.com/product/r-series-subwoofer-r2w10d2 https://www.youtube.com/watch?v=J8g6EZzZQyI&t=131s

Alpine SBT-S10V Truck Loaded SWT Enclosure 1000W Peak (350W RMS) Single 10" Loaded Ported Subwoofer Enclosure With a compact wedge-style design and shallow mount, the SBT-S10V (2-ohm system) is a perfect fit for truck applications, with a design that works in small spaces. The Alpine logos on the front and the bottom offer convenient visibility options when mounted horizontally or vertically. Creates a symmetrical magnetic field with evenly distributed flux density to reduce distortion while improving power handling and output significantly. Provides the mechanical clearance needed for over 50mm of peak-to-peak excursion, unleashing massive output potential from a small package. The High-Amplitude Multi Roll Surround Design allows for extreme excursions without sacrificing valuable cone area. FEA Optimized for linearity and made with injection-molded Santoprene ®, the HAMR surround is a key part of the suspension system that provides accurate, distortion-free control at extreme excursions. More Bass, Less SpaceWith a compact wedge-style design and shallow mount, the SBT-S10V (2-ohm system) is a perfect fit for truck applications, with a design that works in small spaces.Two-Way Alpine Logo FlexibilityThe Alpine logos on the front and the bottom offer convenient visibility options when mounted horizontally or vertically.Significant Output in a Compact Package with 4 Unique Alpine Subwoofer TechnologiesRadial Vented VC Heat Sink & Airflow Management SystemActively manages voice coil temperatures by forcing air directly across the heat sink system. FEA Optimized Dual-Sided Machined CRC Motor Structure Creates a symmetrical magnetic field with evenly distributed flux density to reduce distortion while improving power handling and output significantly. FEA Optimized Injection Molded TPE Spider with Pass-Through Gap Design Provides the mechanical clearance needed for over 50mm of peak-to-peak excursion, unleashing massive output potential from a small package Subwoofer Features: 10" SWT Series Single 2-ohm Shallow Mount Subwoofer Peak Power Handling: 1000 watts RMS Power Handling: 350 watts Recommended Power Range: 100W - 350W Poly-Mica Dust Cap & Pulp-Kevlar Polyurethane Foam Surround, featuring H.A.M.R. Surround Technology Spiral Cut Aluminum Former 65mm Voice Coil with High-Temp 4-Layer SVC Winding Frequency Response: 28 - 200 Hz Sensitivity: 84.8 dB Authorized Dealer 1-year Manufacturer's Warranty Enclosure Features: Ported angled / wedge-style truck enclosure 3/8" medium-density fiberboard (MDF) construction Automotive-grade dark grey carpet 8AWG Push Terminals Protective mesh subwoofer grilled included Dimensions: 7"D x 22"W x 16"H What's in the SBT-S10V package: Ported enclosure loaded with one 10" woofer 2 Mounting plates Six 1/2" Self-tapping screws Owner's manual (English/ French/ Spanish) Installation notes Warranty information Online product registration information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine W10S4 10" Bass Subwoofer 750W Max (250W RMS) 10" BassLine Series Single 4 ohm Car Subwoofer Legendary Alpine quality at an affordable priceCar audio enthusiasts know that Alpine is the leader in technology and innovation. Their reputation for developing the most reliable products is legendary. The BassLine product line is their quest to give customers a quality product that won't break the bank.The surround and wattage match made in heaven.The 250 watts of continuous power that the W10S4 handles complements the poly-foam surround that Alpine went with. It provides the best sound quality money can buy at this price point.General Features: 10" Single 4-ohm BassLine (Bass) Series Subwoofer Power Handling: Peak: 750 watts RMS: 250 watts Recommended power range: 50W - 250W RMS Polypropylene-Mica cone High-excursion poly-foam surround Progressive Wavelet Ribs (P.W.R.) cone design An optional Alpine KTE-10PG subwoofer grill is available and is a wonderful complement to the trim ring with the Alpine logo High-strength custom steel frame 8AWG push terminals 2" voice coil 52oz. magnet Top-mount depth: 5-1/16" Cutout diameter: 9" Frequency Response: 24 - 200Hz Sensitivity: 86.6dB Resonance Frequency (Fs): 32 Authorized Dealer 1-year Manufacturer's Warranty What's in the  W10S4 package: W10S4 owner's manual One 10" Subwoofer per box Adhesive-backed foam gasket Application Guide Online product registration information Warranty Information Important Notice! Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine R-SB12V Pre-loaded R-Series 12-Inch Subwoofer Enclosure Enclosure Stacking Features Unique to Alpine, the subwoofer 10-inch and 12-inch enclosures are available as a single or “linked” format with an optional mounting bracket. This innovative design allows the sound consumer the option to easily add more bass to their system.The optional mounting bracket (sold separately) is available in a 10-inch KTX-H10 or 12-inch KTX-H12 solution that mounts to the face of the subwoofer and links for a sturdy, dual-subwoofer enclosure. The silver enclosure trim matches the steel bracketing and Halo display trim for a synergized look. Optimized Performance The ported enclosure design delivers a higher total sound output for deep, powerful bass, reliable sound reproduction, and overall great sound quality. The 10-inch enclosure is tuned to 36 Hz while the 12-inch enclosure is tuned to 35 Hz for optimized performance with Alpine’s S-and-R-Series subwoofers. General Features: Includes R-W12D4 wired in parallel 750W RMS power handling 2 Ohm Impedance Ported Enclosure Design Frequency Response: 24-200Hz Vent Tuning Frequency: 35Hz Dimensions: 17" W x 14.625" H x 15" D Authorized Dealer 1-year Warranty What is in the box: Ported enclosure loaded with one R-W12D4 subwoofer driver Rubber flange protector (installed on the subwoofer) ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov