All Car Subwoofers (390)

Alpine S-W10D2 1800W Max (600W RMS) 10" S-Series Dual 2 Ohm Car Subwoofer with Absolute VGS10 Ported Subwoofer Box Alpine introduces the all-new S-Series Subwoofers; their unique design substantially improves bass output and provides installation versatility. Each S-Series subwoofer uses a custom-stamped steel frame and is available in twelve, ten, and eight-inch. These high-strength frames were designed to withstand the rigors of the improved S-Series motor. They have frame leg vents, a vented back plate to help cool the subwoofer voice coil and motor parts, and a shallow design to help fit in smaller spaces. The S-Series Subwoofers incorporate two strontium ferrite magnets stacked together, providing increased motor strength and excursion, ultimately delivering an accurate bass to your music. The convenient push-type insert terminals with a dual voice coil jumper system will significantly reduce installation time. Just strip the speaker insulation at the wire end, then insert the bare wire into the hole of the spring-loaded push terminal. At the same time, the concealed mount gasket system creates a clean, finished appearance for any vehicle. General Features: 10" 2 ohm S-Series (Type-S) Subwoofer RMS Power Handling: 600 watts Peak Power Handling: 1800 watts  Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 4-11/16" Cutout diameter: 8-13/16 Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 33 Hz Authorized Dealer 1-year Manufacturer's Warranty What is in the S-W10D2 package: S-W10D2 owner's manual One 10" Dual 2-ohm voice coil subwoofer 1 Rubber concealing ring Two 3" jumper cables (each has a single banana connector on each end) Subwoofer Application Guide Online product registration information Warranty Information ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine S-W10D2 1800W Max (600W RMS) 10" S-Series Dual 2 Ohm Car Subwoofer with Absolute SS10 Sealed Subwoofer Box Alpine introduces the all-new S-Series Subwoofers; their unique design substantially improves bass output and provides installation versatility. Each S-Series subwoofer uses a custom-stamped steel frame and is available in twelve, ten, and eight-inch. These high-strength frames were designed to withstand the rigors of the improved S-Series motor. They have frame leg vents, a vented back plate to help cool the subwoofer voice coil and motor parts, and a shallow design to help fit in smaller spaces. The S-Series Subwoofers incorporate two strontium ferrite magnets stacked together, providing increased motor strength and excursion, ultimately delivering an accurate bass to your music. The convenient push-type insert terminals with a dual voice coil jumper system will significantly reduce installation time. Just strip the speaker insulation at the wire end, then insert the bare wire into the hole of the spring-loaded push terminal. At the same time, the concealed mount gasket system creates a clean, finished appearance for any vehicle. General Features: 10" 2 ohm S-Series (Type-S) Subwoofer RMS Power Handling: 600 watts Peak Power Handling: 1800 watts  Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 4-11/16" Cutout diameter: 8-13/16 Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 33 Hz Authorized Dealer 1-year Manufacturer's Warranty What is in the S-W10D2 package: S-W10D2 owner's manual One 10" Dual 2-ohm voice coil subwoofer 1 Rubber concealing ring Two 3" jumper cables (each has a single banana connector on each end) Subwoofer Application Guide Online product registration information Warranty Information ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

2 Alpine S-W10D2 1800W Max (600W RMS) 10" S-Series Dual 2 Ohm Car Subwoofer  with Absolute TW500 Tweeter & BT1700 Electrical Tape & Mobile Holder   Alpine introduces the all-new S-Series Subwoofers; their unique design substantially improves bass output and provides installation versatility. Each S-Series subwoofer uses a custom-stamped steel frame and is available in twelve, ten, and eight-inch. These high-strength frames were designed to withstand the rigors of the improved S-Series motor. They have frame leg vents, a vented back plate to help cool the subwoofer voice coil and motor parts, and a shallow design to help fit in smaller spaces. The S-Series Subwoofers incorporate two strontium ferrite magnets stacked together, providing increased motor strength and excursion, ultimately delivering an accurate bass to your music. The convenient push-type insert terminals with a dual voice coil jumper system will significantly reduce installation time. Just strip the speaker insulation at the wire end, then insert the bare wire into the hole of the spring-loaded push terminal. At the same time, the concealed mount gasket system creates a clean, finished appearance for any vehicle. General Features: 10" 2 ohm S-Series (Type-S) Subwoofer RMS Power Handling: 600 watts Peak Power Handling: 1800 watts  Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 4-11/16" Cutout diameter: 8-13/16 Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 33 Hz Authorized Dealer 1-year Manufacturer's Warranty What is in the S-W10D2 package: S-W10D2 owner's manual One 10" Dual 2-ohm voice coil subwoofer 1 Rubber concealing ring Two 3" jumper cables (each has a single banana connector on each end) Subwoofer Application Guide Online product registration information Warranty Information ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

2 Cerwin Vega XED12V2 1000 Watts 4 Ohm SVC XED Series Subwoofer Universal 12" XED Mobile Series 1000W 4-ohm SVC Subwoofer by Cerwin-Vega. Feel the bass with these premium quality subwoofers by Cerwin-Vega designed and manufactured to deliver the decibels. Constructed from the highest quality materials with the utmost attention to every tiny detail, they will provide maximum performance for years to come. General Features: 12" Single 4-ohm Xtreme-Energy Design Subwoofer Parabolic Poly Cone Single Stitched High Roll Surround Vented Pole Piece/Basket for Cooler Voice Coil Temperatures Bumped Back Plate for Maximum Excursion Signature Cerwin-Vega Bass Peak Power Handling: 1000W RMS Power Handling: 150W Impedance: 4 Ohms Voice Coil: Single Voice Coil Size: 2" Mounting Diameter: 10.82" Mounting Depth: 5.25" Sensitivity: 85.5dB Authorized Internet Dealer 1-year Manufacturer's Warranty ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

2 Soundstream T5.102 Tarantula T5 1,800 Watt 10" Dual 2-Ohm Subwoofer Tarantula subwoofers have grown to meet various performance and placement goals in recent years, keeping your, the Soundstream fanatic, suggestions in mind. However, more often than not, we hear your calls to bring back a legend. Improvements include direct connect wire leads, over-saturated 12mm top plate and t-yoke, & double-stitched cone to high-density polyether foam surround for improved sound quality. Key components that you expect from T5 remain; a big ass 3” voice coil, a triple-stack magnet assembly, a high-density Spruce pulp sub-cone, and the iconic black-on-black Soundstream Spider. The T5 can handle a lot of power, so be sure to choose a suitable amplifier, as these bass monsters want lots of power. Its different impedance configurations offer wiring flexibility you’ll appreciate as your system changes and grows, so you can always pull maximum power from your amp. It works well in sealed and ported enclosures, so you can choose what kind of bass you want to hear and feel. General Features: Overcompensating Motor Structure for Increased Magnetic Strength 12mm T-Yoke & Top Plate Improve Low-Frequency Dynamics Vented T-Yoke & Frame Reduces Voice Coil Heat Build-up Non-Magnetic Non-Resonate Die-Cast Aluminum Frame 3” 4-Layer Voice Coil w/ Direct Connect Wire Increases Power Handling High-Temperature Tolerance Adhesives Resist Thermal Failure Non-Transfer Spruce Pulp Cone w/ UV & Chemical Protection Stitched and Glued Surround/Cone Joints for Strongest Bonding Extended Excursion Polyether Foam Surround w/ UV & Chemical Protection Dual Poly-Cotton Suspension Dampen Violent Accelerations 1-pc Gasket/Trim Ring w/ Concealed Mounting Holes Include ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Soundstream T5.102 Tarantula T5 1,800 Watt 10" Dual 2-Ohm Subwoofer Tarantula subwoofers have grown to meet various performance and placement goals in recent years, keeping your, the Soundstream fanatic, suggestions in mind. However, more often than not, we hear your calls to bring back a legend. Improvements include direct connect wire leads, over-saturated 12mm top plate and t-yoke, & double-stitched cone to high-density polyether foam surround for improved sound quality. Key components that you expect from T5 remain; a big ass 3” voice coil, a triple-stack magnet assembly, a high-density Spruce pulp sub-cone, and the iconic black-on-black Soundstream Spider. The T5 can handle a lot of power, so be sure to choose a suitable amplifier, as these bass monsters want lots of power. Its different impedance configurations offer wiring flexibility you’ll appreciate as your system changes and grows, so you can always pull maximum power from your amp. It works well in sealed and ported enclosures, so you can choose what kind of bass you want to hear and feel. General Features: Overcompensating Motor Structure for Increased Magnetic Strength 12mm T-Yoke & Top Plate Improve Low-Frequency Dynamics Vented T-Yoke & Frame Reduces Voice Coil Heat Build-up Non-Magnetic Non-Resonate Die-Cast Aluminum Frame 3” 4-Layer Voice Coil w/ Direct Connect Wire Increases Power Handling High-Temperature Tolerance Adhesives Resist Thermal Failure Non-Transfer Spruce Pulp Cone w/ UV & Chemical Protection Stitched and Glued Surround/Cone Joints for Strongest Bonding Extended Excursion Polyether Foam Surround w/ UV & Chemical Protection Dual Poly-Cotton Suspension Dampen Violent Accelerations 1-pc Gasket/Trim Ring w/ Concealed Mounting Holes Include ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

2 Power Acoustik EW-124S 1400W Max (700W RMS) 12" Edge Shallow Series Single 4ohm Car Subwoofer 2.5″ Depth Subwoofer Edge Shallow Subwoofers combine performance and value. These shallow subwoofers perform best in small sealed enclosures, with minimal power requirements, thanks to cone and suspension design efficiencies. General Features: Specifications EW-124S Max Power Handling 1,400 Watts RMS Power Handling 700 Watts Shallow mount design for mounting in any space Stamped Steel Basket Screw down terminals Single 2" voice coil Authorized Internet Dealer Efficiency (1w/1m) 83.60 Voice Coil Configuration 2.00″ 4Ω Motor Volume 60oz Mounting Depth 2.50″ Optimum Sealed Enclosure ft3 1.00 1-year manufacturer warranty ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Power Acoustik EW-124S 1400W Max (700W RMS) 12" Edge Shallow Series Single 4ohm Car Subwoofer 2.5″ Depth Subwoofer Edge Shallow Subwoofers combine performance and value. These shallow subwoofers perform best in small sealed enclosures, with minimal power requirements, thanks to cone and suspension design efficiencies. General Features: Specifications EW-124S Max Power Handling 1,400 Watts RMS Power Handling 700 Watts Shallow mount design for mounting in any space Stamped Steel Basket Screw down terminals Single 2" voice coil Authorized Internet Dealer Efficiency (1w/1m) 83.60 Voice Coil Configuration 2.00″ 4Ω Motor Volume 60oz Mounting Depth 2.50″ Optimum Sealed Enclosure ft3 1.00 1-year manufacturer warranty ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine RS-SB10 10" Halo R-Series R2 Preloaded Subwoofer Enclosure with ProLink The next generation of sound performance is here with the new R-Series Halo Preloaded Subwoofers featuring the new R-Series “R2” subwoofers for more accurate and authoritative bass. PRODUCT FEATURES: Unique ProLink Design – ProLink is unique to Alpine and allows you to link two R2-SB10V enclosures together using an optional KTX-H10 linking kit to create a dual subwoofer enclosure. Stand Out in the Crowd – Drawing inspiration from the sleek, tapered lines and clean silver finish of the Alpine Halo display, the R2-SB10V shares the same unique, curved edges outlined by a silver trim and a metallic front baffle for a matching system aesthetic. Improved Performance – The new R-Series subwoofers now feature larger, double-stacked magnets that contribute more motor force for deeper bass and tighter bass control compared to the previous generation. General Specs: Size: 10” Weight: 42 lbs Dimensions: 16” x 12.68” x 14.5” Frequency Response: 26Hz - 200Hz Power Range: 300W - 750W RMS Power Handling: 750W RMS / 2250W Peak Magnet Weight: 123 oz Voice Coil Diameter: 65.5 mm (2.6”) Linear Excursion (Xmax): 20 mm T/S Parameters: Sensitivity (1W/1m): 82.3 dB DC Resistance (Re): 1.9Δ + 1.9Δ Free Air Resonance (Fs): 31 Hz Equivalent Stiffness: 18.2 L Mechanical Q (Qms): 7.07 Electrical Q (Qes): 0.5 Total Q (Qts): 0.47 Cone Area (Sd): 333 cm2 Linear Excursion (Xmax): 20 mm Mechanical Travel (Xmech): 70 mm The next generation of sound performance is here with the new R-Series Halo Preloaded Subwoofers featuring the new R-Series “R2” subwoofers for more accurate and authoritative bass. Unique ProLink Design – ProLink is unique to Alpine and allows you to link two R2-SB10V enclosures together using an optional KTX-H10 linking kit to create a dual subwoofer enclosure. Stand Out in the Crowd – Drawing inspiration from the sleek, tapered lines and clean silver finish of the Alpine Halo display, the R2-SB10V shares the same unique, curved edges outlined by a silver trim and a metallic front baffle for a matching system aesthetic. Improved Performance – The new R-Series subwoofers now feature larger, double-stacked magnets that contribute more motor force for deeper bass and tighter bass control compared to the previous generation.