All Car Amplifiers (491)

Alpine KTP-445A Plug and Play Head Unit Power Pack for Use with 2005-Up Alpine Head Units with a Black Power Harness The KTP-445A Power Pack amplifies the power output on select 2005 and newer Alpine head units, resulting in a power increase of up to 150% over the original power from the head unit's built-in amplifier. The compact size of the KTP-445A allows it to fit where most amplifiers won’t. The KTP-445A comes equipped with direct plug-in connectors for select 2005 and newer Alpine head units, and it fits behind the dash of most vehicles. It's small and compact at only 7-7/16” x 1-1/2” x 2-1/2”. Its size and flexible wires make the Power Pack an easy choice to save space. To ensure that Alpine sound quality is heard, we’ve created a platform that offers an unbelievably low noise floor, taking extra care to ensure a clean signal path with no extraneous interference. The result: The Power Pack boasts a signal-to-noise ratio of 82dB or better.  General Features: Alpine Power Pack 4-Channel Class D for Select In-Dash Receivers Plug-and-play design for compatible Alpine head units (2005 - Up, Black 16 Pin) RMS Power Rating: 4 ohms: 45 watts x 4 Channel Total RMS power output: 180 watts CEA-2006 compliant amplifier Increases the output of an Alpine head unit without having to install a full-size amplifier and amp install kit The fast and easy solution to higher power aftermarket sound High-efficiency digital circuit design Gain optimized for Alpine head units Plugs directly into the wiring harness of the Alpine receiver Fast and simple installation 4-channel operation for four speakers It is not compatible with factory amplifiers Frequency response: 20-20,000 Hz Signal to Noise Ratio: 84 dBA Fuse Rating: 15A x 1 Includes both Amp-to-receiver and Amp-to-vehicle Harnesses Dimensions: 7-13/16D x 2-9/16"W x 1-1/2"H Authorized Dealer 1-year Manufacturer's Warranty What is in the KTP-445A package: Head Unit Power Pack (15A fuse installed) 39" Amp-to-receiver harness (male 16-pin connector on each end) 31" Amp-to-vehicle harness (male 16-pin connector on one end and a female 16-pin connector on the other end) 2 Brackets 4 Screws 4 Wire-ties Installation Diagram Online Product Registration Limited Warranty Information KTP-445A Power Pack owner's manual Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine KTA-30MW Car Amplifier Mono 300-Watt RMS Weather-Resistant Tough Power Pack Amplifier A TOUGH MINI AMP THAT PACKS A PUNCH Get big amp performance in a compact, resilient package. With Alpine’s exclusive technology, Dynamic Peak Power (D.P.P.), the KTA-30MW Weather Resistant Tough Power Pack is sure to deliver powerful bass output for subwoofers used in those open cab vehicles and toys. This small and efficient amplifier can be installed with an aftermarket or factory head unit while adding up to 600 watts of D.P.P. power. Its weather resistance makes the KTA-30MW a good choice for use in exposed installations like side-by-sides, boats, open-top vehicles, and motorcycle saddlebags. A SOUND SYSTEM BOOST WITHOUT THE BIG SPACE COMMITMENT The KTA-30MW is perfect for when you want to add subwoofer power but don’t have space for a large amplifier. It is compatible with an aftermarket or factory head unit and provides up to 600 DPP watts to the subwoofer of your choice. HALF THE SIZE OF OUR SMALLEST TRADITIONAL AMPLIFIERS The KTA-30MW measures just 9-3/16” (W) x 1-5/8” (H) x 3-3/4” (D), so its small footprint lets it fit where most amplifiers won’t, like under the dash or in the glove compartment, installed under the dash of a side-by-side, placed in the saddlebag of a motorcycle, or used in other places where space is an issue. General Features: Alpine KTA-30MW Class D Monoblock Weather-Resistant Power Pack Amplifier 300 Watts RMS X 1 @ 4 Ohms Power Handling 600 Watts RMS X 1 @ 2 Ohms Power Handling CTA-2006 compliant Frequency Response: 20-400 Hz Total Harmonic Distortion (THD): <1% Signal to Noise Ratio: 83dB Variable Low Pass filter 50-400Hz @ -24dB/Oct. Variable Bass Boost (0-12 dB at 50 Hz) Fuse Rating: 25A Weather-resistant (IP66 rating) Dynamic Peak Power (D.P.P.) technology intelligently adjusts the gain to automatically adapt to musical needs Dimensions: 7” W x 3.5” H x 1.25” D Authorized Dealer 1-year Manufacturer's Warranty What is in the box: Mono amplifier 14" Power/signal harness (26-pin connector on one end and bare wires + RCAs on the other ends) 4 Self-tapping screws (Length 3/4") Connection sheet Limited Warranty sheet Alpine KTA-30MW owner's manual Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca. 

Alpine KTA-30MW Car Amplifier Mono 300-Watt RMS Weather Resistant Tough Power Pack Amplifier A TOUGH MINI AMP THAT PACKS A PUNCH Get big amp performance in a compact, resilient package. With Alpine’s exclusive technology, Dynamic Peak Power (D.P.P.), the KTA-30MW Weather Resistant Tough Power Pack will surely deliver powerful bass output for subwoofers in those open cab vehicles and toys. This small and efficient amplifier can be installed with an aftermarket or factory head unit while adding up to 600 watts of D.P.P. power. Its weather resistance makes the KTA-30MW a good choice in exposed installations like side-by-sides, boats, open-top vehicles, and motorcycle saddlebags. A SOUND SYSTEM BOOST WITHOUT THE BIG SPACE COMMITMENT The KTA-30MW is perfect for when you want to add subwoofer power but don’t have space for a large amplifier. It is compatible with an aftermarket or factory head unit and provides up to 600 DPP watts to the subwoofer of your choice. HALF THE SIZE OF OUR SMALLEST TRADITIONAL AMPLIFIERS The KTA-30MW measures just 9-3/16” (W) x 1-5/8” (H) x 3-3/4” (D), so its small footprint lets it fit where most amplifiers won’t, like under the dash or in the glove compartment, installed under the dash of a side-by-side, placed in the saddlebag of a motorcycle, or used in other places where space is an issue. General Features: Alpine KTA-30MW Class D Monoblock Weather Resistant Power Pack Amplifier 300 Watts RMS X 1 @ 4 Ohms Power Handling 600 Watts RMS X 1 @ 2 Ohms Power Handling CTA-2006 compliant Frequency Response: 20-400 Hz Total Harmonic Distortion (THD): <1% Signal to Noise Ratio: 83dB Variable Low Pass filter 50-400Hz @ -24dB/Oct. Variable Bass Boost (0-12 dB at 50 Hz) Fuse Rating: 25A Weather-resistant (IP66 rating) Dynamic Peak Power (D.P.P.) technology intelligently adjusts the gain to adapt to musical needs automatically Dimensions: 7” W x 3.5” H x 1.25” D Authorized Dealer 1-year Manufacturer's Warranty What is in the box: Mono amplifier 14" Power/signal harness (26-pin connector on one end and bare wires + RCAs on other ends) 4 Self-tapping screws (Length 3/4") Connection sheet Limited Warranty sheet Alpine KTA-30MW owner's manual Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine KTA-30MW Car Amplifier Mono 300-Watt RMS Weather Resistant Tough Power Pack Amplifier A TOUGH MINI AMP THAT PACKS A PUNCH Get big amp performance in a compact, resilient package. With Alpine’s exclusive technology, Dynamic Peak Power (D.P.P.), the KTA-30MW Weather Resistant Tough Power Pack is sure to deliver powerful bass output for subwoofers used in those open cab vehicles and toys. This small and efficient amplifier can be installed with an aftermarket or factory head unit while adding up to 600 watts of D.P.P. power. Its weather resistance makes the KTA-30MW a good choice for use in exposed installations like side-by-sides, boats, open-top vehicles, and motorcycle saddlebags. A SOUND SYSTEM BOOST WITHOUT THE BIG SPACE COMMITMENT The KTA-30MW is perfect for when you want to add subwoofer power but don’t have space for a large amplifier. It is compatible with an aftermarket or factory head unit and provides up to 600 DPP watts to the subwoofer of your choice. HALF THE SIZE OF OUR SMALLEST TRADITIONAL AMPLIFIERS The KTA-30MW measures just 9-3/16” (W) x 1-5/8” (H) x 3-3/4” (D), so its small footprint lets it fit where most amplifiers won’t, like under the dash or in the glove compartment, installed under the dash of a side-by-side, placed in the saddlebag of a motorcycle, or used in other places where space is an issue. General Features: Alpine KTA-30MW Class D Monoblock Weather Resistant Power Pack Amplifier 300 Watts RMS X 1 @ 4 Ohms Power Handling 600 Watts RMS X 1 @ 2 Ohms Power Handling CTA-2006 compliant Frequency Response: 20-400 Hz Total Harmonic Distortion (THD): <1% Signal to Noise Ratio: 83dB Variable Low Pass filter 50-400Hz @ -24dB/Oct. Variable Bass Boost (0-12 dB at 50 Hz) Fuse Rating: 25A Weather-resistant (IP66 rating) Dynamic Peak Power (D.P.P.) technology intelligently adjusts the gain to automatically adapt to musical needs Dimensions: 7” W x 3.5” H x 1.25” D Authorized Dealer 1-year Manufacturer's Warranty What is in the box: Mono amplifier 14" Power/signal harness (26-pin connector on one end and bare wires + RCAs on other ends) 4 Self-tapping screws (Length 3/4") Connection sheet Limited Warranty sheet Alpine KTA-30MW owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Rockford Fosgate Prime R2-750X1 750W RMS Prime Series Class-D Monoblock 1-Ohm Stable AmplifierLooking for a monoblock with reliable power ratings and efficiency without spending a fortune? Rockford Fosgate's R2-750X1. With a rating of 250 watts x 1 channel @ 4 ohms, 500 watts x 1 channel @ 2 ohms, and 750 watts x 1 channel at 1 ohm, this amplifier is perfect for those looking to amplify anything from entry-level to some more serious power at the 1-ohm rating. Fine-tuning your amplifier will be a cinch using the variable high-pass, infrasonic, and variable bass boost crossovers. A cast aluminum heat sink will control heat dissipation to keep your amplifier running cool and efficiently no matter how long or short your listening sessions are. So if you are looking for a Class D highly efficient monoblock amplifier that will never let you down, look no further than Rockford Fosgate's R2-750X1. General Features: Rockford Fosgate Prime R2-750X1 Class-D FullRange MonoBlock Amplifier RMS Power Rating: 4 ohms: 250 watts x 1 channel RMS Power Rating: 2 ohms: 500 watts x 1 channel RMS Power Rating: 1 ohm: 750 watts x 1 channel Total power output: 500 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeatable Auto Turn-On Circuit Features C.L.E.A.N. Set-up Variable Input Gain adjustment level R.L.C. Remote Level Control Variable Infrasonic Filter Continuously Variable On Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Full Range Class D Rollback Protection Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers Input sensitivity: Low-Level: 150 mV - 4 V High-Level: 450 mV - 12 V Frequency Response: 20 Hz - 250 Hz Total Harmonic Distortion (THD): >1% Crossover Controls Low-Pass: 50 Hz - 250 Hz Sub Infrasonic: 15 Hz - 40 Hz Recommended Fuse Rating: 120A 4 gauge power and ground wiring is recommended for installation Dimensions: "1.9" x "6.8" x "10.1" Authorized Internet Dealer 1-Year Manufacturer's Warranty ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine KTA-30MW Car Amplifier Mono 300-Watt RMS Weather Resistant Tough Power Pack Amplifier A TOUGH MINI AMP THAT PACKS A PUNCH Get big amp performance in a compact, resilient package. With Alpine’s exclusive technology, Dynamic Peak Power (D.P.P.), the KTA-30MW Weather Resistant Tough Power Pack will deliver powerful bass output for subwoofers in those open cab vehicles and toys. This small and efficient amplifier can be installed with an aftermarket or factory head unit while adding up to 600 watts of D.P.P. power. Its weather resistance makes the KTA-30MW a good choice in exposed installations like side-by-sides, boats, open-top vehicles, and motorcycle saddlebags. A SOUND SYSTEM BOOST WITHOUT THE BIG SPACE COMMITMENT The KTA-30MW is perfect for when you want to add subwoofer power but don’t have space for a large amplifier. It is compatible with an aftermarket or factory head unit and provides up to 600 DPP watts to the subwoofer of your choice. HALF THE SIZE OF OUR SMALLEST TRADITIONAL AMPLIFIERS The KTA-30MW measures just 9-3/16” (W) x 1-5/8” (H) x 3-3/4” (D), so its small footprint lets it fit where most amplifiers won’t, like under the dash or in the glove compartment, installed under the dash of a side-by-side, placed in the saddlebag of a motorcycle, or used in other places where space is an issue. General Features: Alpine KTA-30MW Class D Monoblock Weather Resistant Power Pack Amplifier 300 Watts RMS X 1 @ 4 Ohms Power Handling 600 Watts RMS X 1 @ 2 Ohms Power Handling CTA-2006 compliant Frequency Response: 20-400 Hz Total Harmonic Distortion (THD): <1% Signal to Noise Ratio: 83dB Variable Low Pass filter 50-400Hz @ -24dB/Oct. Variable Bass Boost (0-12 dB at 50 Hz) Fuse Rating: 25A Weather-resistant (IP66 rating) Dynamic Peak Power (D.P.P.) technology intelligently adjusts the gain to adapt to musical needs automatically Dimensions: 7” W x 3.5” H x 1.25” D Authorized Dealer 1-year Manufacturer's Warranty What is in the KTA-30MW box: Mono amplifier 14" Power/signal harness (26-pin connector on one end and bare wires + RCAs on other ends) 4 Self-tapping screws (Length 3/4") Connection sheet Limited Warranty sheet KTA-30MW owner's manual Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine KTA-30MW Car Amplifier Mono 300-Watt RMS Weather Resistant Tough Power Pack Amplifier A TOUGH MINI AMP THAT PACKS A PUNCH Get big amp performance in a compact, resilient package. With Alpine’s exclusive technology, Dynamic Peak Power (D.P.P.), the KTA-30MW Weather Resistant Tough Power Pack is sure to deliver powerful bass output for subwoofers used in those open cab vehicles and toys. This small and efficient amplifier can be installed with an aftermarket or factory head unit while adding up to 600 watts of D.P.P. power. Its weather resistance makes the KTA-30MW a good choice for use in exposed installations like side-by-sides, boats, open-top vehicles, and motorcycle saddlebags. A SOUND SYSTEM BOOST WITHOUT THE BIG SPACE COMMITMENT The KTA-30MW is perfect for when you want to add subwoofer power but don’t have space for a large amplifier. It is compatible with an aftermarket or factory head unit and provides up to 600 DPP watts to the subwoofer of your choice. HALF THE SIZE OF OUR SMALLEST TRADITIONAL AMPLIFIERS The KTA-30MW measures just 9-3/16” (W) x 1-5/8” (H) x 3-3/4” (D), so its small footprint lets it fit where most amplifiers won’t, like under the dash or in the glove compartment, installed under the dash of a side-by-side, placed in the saddlebag of a motorcycle, or used in other places where space is an issue. General Features: Alpine KTA-30MW Class D Monoblock Weather Resistant Power Pack Amplifier 300 Watts RMS X 1 @ 4 Ohms Power Handling 600 Watts RMS X 1 @ 2 Ohms Power Handling CTA-2006 compliant Frequency Response: 20-400 Hz Total Harmonic Distortion (THD): <1% Signal to Noise Ratio: 83dB Variable Low Pass filter 50-400Hz @ -24dB/Oct. Variable Bass Boost (0-12 dB at 50 Hz) Fuse Rating: 25A Weather-resistant (IP66 rating) Dynamic Peak Power (D.P.P.) technology intelligently adjusts the gain to automatically adapt to musical needs Dimensions: 7” W x 3.5” H x 1.25” D Authorized Dealer 1-year Manufacturer's Warranty What is in the box: Mono amplifier 14" Power/signal harness (26-pin connector on one end and bare wires + RCAs on other ends) 4 Self-tapping screws (Length 3/4") Connection sheet Limited Warranty sheet Alpine KTA-30MW owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine S-A60M 500W V-Power Series Class D Monoblock Digital Amplifier + Absolute KIT4 4 Gauge Complete Amplifier Kit Born Tough, Raised Strong Tens of thousands have relied on V-Power amplifiers for dependable, quality power. Now in their fourth generation, V-Power amplifiers carry on this heritage and prove that playing strong never looked or sounded better. Yes, it is possible to improve upon a good thing. General Features: V-Power Series Class D Monoblock Digital Amplifier RMS Power Rating: 4 ohms: 300 watts x 1 Chan. 2 ohms: 500 watts x 1 Chan. Max power output: 500 watts x 1 Chan. Integrated wire and mounting screw terminals S.T.A.R. circuitry LED power (blue) and protect (red) indicators Variable Bass Boost (0 to +12 dB bass boost at 50 Hz) Optional Alpine RUX-KNOB.2 remote bass knob available Soft start turn-on 4 or 2 channel operation 4-channel speaker-level inputs Pre-amp RCA outputs to daisy chain multiple amps 3-way protection circuitry (thermal, overload, and speaker short protection) Dual speaker terminals simplify the hookup of multiple speakers Heavy-duty aluminum alloy heat-sink Input sensitivity: 0.4V - 10V Non-fading pre-amp output Variable low-pass filter (50-400 Hz, 24 dB/octave) CEA-2006 compliant amplifier Dimensions: 7-7/8"W x 7-7/8"L x 2-3/16"H Authorized Dealer 1-year Manufacturer's Warranty Absolute KIT-4 Complete 4 Gauge Amplifier Kit Product Features: Complete 4 Gauge Amplifier Kit Designed specifically for car audio systems up to 1000 watts Premium power and ground wire provides optimal power transfer Includes 2-channel RCA interconnect cables for the audio signal connection from the receiver to the amplifier Terminals are gold-plated for excellent signal transfer For use in any car, truck, RV, or boat Package Includes: 17 ft. of red 4 AWG high current power cable 3 ft. of black 4 AWG ground cable 15 ft. of RCA triple shielded interconnect audio cable with built-in remote wire 20 ft. of 12 AWG OFC Speaker cable 20 ft. of 16 AWG remote turn-on wire 6 ft. of split loom tubing 1 Gold plated 80 AMP AGU fuse 1 4 AWG gold ring terminal 1 4 AWG water-resistant inline fuse holder 2 Ring terminals 2 Spade terminals (4 gauge) 5 Spade terminals (14-16 gauge) 3 Self-tapping screws 1 Rubber grommet 20 Black cable ties 2 Butt connectors (18-22 gauge) 1 Butt connector (4 gauge)