00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Alpine KTP-445A Car Amplifier Plug and Play Head Unit Power Pack for Use w/ 2005-Up Alpine Head Units
$289.95
$450.00
Alpine KTP-445A Plug and Play Head Unit Power Pack for Use w/ 2005-Up Alpine Head Units with a Black Power Harness
The KTP-445A Power Pack amplifies power output on select 2005 and newer Alpine head units, resulting in up to a 150 percent power increase over the original power from the head unit's built-in amplifier. Compact size lets the KTP-445A fit where most amplifiers won’t. The KTP-445A comes equipped with direct plug-in connectors for select 2005 and newer Alpine head units and it fits behind the dash of most vehicles. It's small and compact at only 7-7/16” x 1-1/2” x 2-1/2”. Its size and flexible wires make the Power Pack an easy choice to save space. In order to ensure that Alpine sound quality is heard, we’ve created a platform that offers an unbelievably low noise floor, taking extra care to ensure a clean signal path, with no extraneous interference. The end result: The Power Pack boasts a 1 Watt Signal-to-Noise Ratio of 82dB or better.
General Features:
Alpine Power Pack 4-Channel Class D for Select In-Dash Receivers
Plug-and-play design for compatible Alpine head units (2005 - Up, Black 16 Pin)
RMS Power Rating:
4 ohms: 45 watts x 4 Channel
Total RMS power output: 180 watts
CEA-2006 compliant amplifier
Increases the output of an Alpine head unit without having to install a full-size amplifier and amp install kit
The fast and easy solution to higher power aftermarket sound
High-efficiency digital circuit design
Gain optimized for Alpine head units
Plugs directly into the wiring harness of the Alpine receiver
Fast and simple installation
4 channel operation for four speakers
Is not compatible with factory amplifiers
Frequency response: 20-20,000 Hz
Signal to Noise Ratio: 84 dBA
Fuse Rating: 15A x 1
Includes both Amp-to-receiver and Amp-to-vehicle Harnesses
Dimensions: 7-13/16D x 2-9/16"W x 1-1/2"H
Authorized Dealer
1-year Manufacturer's Warranty
What is in the KTP-445A package:
Head Unit Power Pack (15A fuse installed)
39" Amp-to-receiver harness (male 16-pin connector on each end)
31" Amp-to-vehicle harness (male 16-pin connector on one end and a female 16-pin connector on other ends)
2 Brackets
4 Screws
4 Wire-ties
Installation Diagram
Online Product Registration
Limited Warranty Information
KTP-445A Power Pack owner's manual
⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov
00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Alpine S-A32F S-Series 320W RMS 4-Channel Digital Class D Car Audio Amplifier
$249.95
$280.00
Alpine S-A32F S-Series 320W RMS 4-Channel Digital Class D Car Audio Amplifier
The all-new S-Series amplifiers pack a punch with even more performance and value. Experience hard-hitting bass and long hours of limitless play with the S-A32F 4-channel amplifier.
These amplifiers offer great value with over 20% more power through increased watt handling. The exceptional strength and resistance are supported by optimizing a heat thermal management processor to ensure exceptional reliability. You can enjoy your music with the bass cranked up for hours without any power shutdown.General Features:
Alpine S-Series S-A32F 4/3/2 Channel Power Amplifier
S-Series amplifiers are your sound system’s workhorse. With unmatched reliability and budget-friendly prices, these amplifiers are the better choice in performance value.
S-Series Amplifier: Known for reliable performance and value-oriented products.
Power Output:
55W RMS x 4 (4ohm, 14.4V ≤ 1% THD+N)
80W RMS x 4 (2ohm, 14.4V≤ 1% THD+N)
Bridged: 160W RMS x 2 (4ohm, 14.4V ≤ 1% THD+N)
Total power output: 320 watts
CEA-2006 Compliant Amplifier
LED Power/Protect Light
Speaker-level (high-level) inputs
3-way protection circuitry (thermal, overload, and short speaker protection)
Frequency Response: 10 - 30,0000 Hz
Total Harmonic Distortion (THD): <1%
Signal Noise Ratio: 83 dB
Variable high-pass filter: 50 - 400 Hz, 12 dB/octave
Variable low-pass filter: 50 - 400 Hz, 12 dB/octave
Fuse Rating: 40
Improved heat sink and protection circuit design
Contain technology currently implemented in the Alpine R and X-Series models
105dB Signal-to-Noise (S/N) ratio at rated power
46 degrees of phase shift
Designed to perform perfectly with the existing S-Series speakers and subwoofers
Dimensions: 8” W x 8” H x 2.25” D
Authorized Dealer
1-year Manufacturer's Warranty
What is in the S-A32F package:
S-A32F owner's manual
4-Channel amplifier
One 40-amp ATO fuse
Four 3/4" Screws
2mm Allen wrench
Alpine Verification Certificate
Warranty information
Online product registration information
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.
00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Alpine S-A55V Car Amplifier
S-Series 5-Channel Class D Amplifier 540W RMS $429.95 $600.00
S-Series 5-Channel Class D Amplifier 540W RMS $429.95 $600.00
Alpine S-A55V S-Series 5-Channel Class D Amplifier 540W RMS
The Alpine S-Series Sound ComponentsThree new S-Series amplifiers join the S-Series family, known for reliable performance and value-oriented products. All three S-Series amps (mono, 4-channel, and 5-channel) contain technology currently implemented in R and X-Series models. The S-Series amps feature attractive prices and are designed to perform perfectly with the existing S-Series speakers. S-Series amplifiers are your sound system’s workhorse. With unmatched reliability and budget-friendly prices, these amplifiers are the better choice in performance value. General Features:
5-channel Class D Amplifier
Power Output:
40 watts RMS x 4 + 200 watts RMS x 1 at 4 ohms
60 watts RMS x 4 + 300 watts RMS x 1 at 2 ohms
120 watts RMS x 2 bridged at 4 ohms + 300 watts RMS x 1 at 2 ohms
CTA-2006 compliant
Variable high-pass filter (50-400 Hz, 12 dB/octave) on 4-channel section
Variable low-pass filter (50-400 Hz, 24 dB/octave) on a subchannel
Variable bass boost (0-12 dB at 50 Hz) on a subchannel
Optional RUX-KNOB.2 wired remote level control for a subchannel
Preamp and speaker-level inputs
speaker wire to RCA adapter required for speaker-level input
Wiring and hardware not included with amplifier
4-gauge power and ground leads recommended
Fuse rating: 30A x 2
Dimensions: 11-1/4" W x 2-1/4" H x 8" D
Authorized Dealer
1-year Manufacturer's Warranty
What's in the box:
5-Channel amplifier
Two 30-amp ATO fuses (installed)
Four 3/4" Screws
2mm Allen wrench
Owner's manual (English/ French/ Spanish)
Alpine Verification Certificate
Warranty information
Power supply note
Online product registration information
Alpine S-A55V owner's manual
⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov
00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Alpine R-A75M Car Amplifier
R-Series Class D Monoblock Subwoofer Amplifier 750 Watts RMS $499.95 $599.99
R-Series Class D Monoblock Subwoofer Amplifier 750 Watts RMS $499.95 $599.99
Alpine R-A75M R-Series Class D Monoblock Subwoofer Amplifier 750 Watts RMS
HI-RESOLUTION AUDIO COMPLIANT
The R-Series amplifiers utilize Alpine’s advanced amplifier platform that takes the classic Class-D amplifier circuit and adds dual post-filter feedback loops for unmatched accuracy and control. This technology., originally launched in the premium X-Series amplifiers, produces efficient power with enhanced dynamic range, qualifying the R-Series amplifiers to be Hi-Resolution Audio compliant.
THE LOUDEST FAMILY ON THE BLOCK
The “R” line of speakers and subwoofers have a heritage of sound quality you can hear from a block away, and the newly added R-Series amplifiers are no exception. Aside from their best-in-class performance, these amplifiers are tuned to emphasize the characteristics of the R-Series speakers and subwoofers, giving you that legendary R-Series experience.
General Features:
R-Series Class D Monoblock Subwoofer Amplifier
Power Output:
500 watts RMS x 1 @ 4 ohms
750 watts RMS x 1 @ 2 ohms
CTA-2006 compliant
Variable low-pass filter (50-400 Hz, 24 dB/octave)
Variable bass boost (0-12 dB at 50 Hz)
Variable subsonic filter (min-40 Hz, 24 dB/octave)
We recommend the Alpine RUX-KNOB.2 if you are looking for a remote bass knob for Alpine Amplifiers
Preamp and speaker-level inputs
Speaker wire to RCA adapter required for speaker-level input - we recommend the Rockford Fosgate RFI2SW
preamp outputs
wiring and hardware not included with amplifier
4-gauge power and ground leads recommended - get the NVX XAPK4 for this
Fuse rating: 40A x 2
Dimensions: 9" W x 2-1/16" H x 7-1/8" D
Authorized Dealer
1-year Manufacturer's Warranty
What's in the R-A75M package:
Mono subwoofer amplifier
Two 40-amp ATO fuses
4 Mounting feet
Four 3/4" Screws
Eight M2.5x5.5mm Machine screws
2mm Allen wrench
3mm Allen wrench
Owner's manual
Alpine Verification Certificate
Warranty information
Power supply note
Online product registration information
Alpine R-A75M owner's manual
⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov
00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Alpine X-A90V Car Amplifier
900W RMS X-Series Class-D 5-Channel 2 Ohm Stable Amplifier 75 watts RMS x 4 at 4 ohms + 500 watts RMS x 1 at 2 ohms $899.95 $950.00
900W RMS X-Series Class-D 5-Channel 2 Ohm Stable Amplifier 75 watts RMS x 4 at 4 ohms + 500 watts RMS x 1 at 2 ohms $899.95 $950.00
Alpine X-A90V 900W RMS X-Series Class-D 5-Channel 2 Ohm Stable Amplifier 75 watts RMS x 4 at 4 ohms + 500 watts RMS x 1 at 2 ohmsAlpine introduces the all-new X-Series of high-grade speakers and amplifiers. These products have been engineered and tuned to create a perfect match for extraordinarily dynamic, realistic sound reproduction, and a spatial sound impression.The all-new X-Series amplifiers set a new standard for sound quality performance and power output in a very compact design. Available in mono, four-channel, and five-channel configuration, these amps are a perfect match for the all-new X-Series speakers and subwoofers.General Features:General Features:
Alpine X-Series X-A90V
Class-D Full Range 2 ohm Stable 5-Channel Amplifier
RMS Power Rating:
4-channel side
4 ohms: 75 watts x 4 channel
2 ohms: 100 watts x 4 channel
1 ohm: ------------N/A------------
Bridged, 4 ohms: 200 watts x 2 channel
Subchannel
4 ohms: 300 watts x 1 chan.
2 ohms: 500 watts x 1 chan.
1 ohm: ------------N/A------------
Total power output: 900 watts
CEA-2006 Compliant Amplifier
Hi-Res Audio compatible
Wired remote bass level control, Alpine RUX-KNOB.2, available
Included plastic covers available to offer a brushed aluminum finish around the edges
LED power (green) and protect (red) indicators
Soft start turn-on
5/3 channel operation
Speaker-level (high-level) inputs
3-way protection circuitry (thermal, overload, and speaker short protection)
Dual speaker terminals simplify the hookup of multiple speakers
Heavy-duty aluminum alloy heat-sink
Input sensitivity
High level: .5 - 10V
Low level: .2 - 4V
Frequency Response:
4-channel: 10 - 60,000Hz
Sub-channel: 8 - 400Hz
Total Harmonic Distortion (THD): .07%
Signal to Noise Ratio: >105dB
Variable high-pass filter: 50 - 400Hz, -24dB/octave
Variable low-pass filter: 50 - 400Hz, -24dB/octave
Subsonic filter: 8 - 40Hz
Variable Bass Boost: 0 to +12 dB bass boost at 50 Hz
Fuse Rating: 30A x 3
4 gauge power and ground wiring is recommended for installation. Contact us for information regarding a discount on select amplifier kits from our website when purchased together with this amplifier.
Dimensions: 11-3/4"W x 7-5/8"L x 2"H
Authorized Dealer
1-year Manufacturer's Warranty
What's in the box:
-Channel amplifier
Three 30A ATO fuses (installed)
Terminal Cover Left
Terminal Cover Right
Terminal Cover Front
Battery connector plug
3 Speaker connector plugs
Logo Plate (self-adhesive)
4 Self-tapping screws (Length 3/4")
2mm Allen wrench
4mm Allen wrench
Owner's Manual
Alpine Verification Certificate
Limited Warranty
To Customers sheet
Alpine X-A90V owner's manual
⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov
00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Alpine R-A60F Car Amplifier
R-Series 4-Channel Power Density Amplifier 600 Watts RMS $499.95 $800.00
R-Series 4-Channel Power Density Amplifier 600 Watts RMS $499.95 $800.00
Alpine R-A60F R-Series 4-Channel Power Density Amplifier 600 Watts RMSHI-RESOLUTION AUDIO COMPLIANT
The R-Series amplifiers utilize Alpine’s advanced amplifier platform that takes the classic Class-D amplifier circuit and adds dual post-filter feedback loops for unmatched accuracy and control. This technology., originally launched in the premium X-Series amplifiers, produces efficient power with enhanced dynamic range, qualifying the R-Series amplifiers to be Hi-Resolution Audio compliant. THE LOUDEST FAMILY ON THE BLOCK
The “R” line of speakers and subwoofers have a heritage of sound quality you can hear from a block away, and the newly added R-Series amplifiers are no exception. Aside from their best-in-class performance, these amplifiers are tuned to emphasize the characteristics of the R-Series speakers and subwoofers, giving you that legendary R-Series experience.
General Features:
Alpine R-A60F
Alpine R-Series 4-Channel Power Density Amplifier
RMS Power Output:
100 Watts x 4 @ 4 Ohm
150 Watts x 4 @ 2 Ohm
300 Watts x 2 @ 4 Ohms Bridged
Class-D Amplifier
Frequency Response: 15 Hz - 45 kHz
S/N ratio: 87dB (ref: 1W into 4 ohm), >106dB (ref: rated power into 4 ohm)
Only 46-degrees of phase shift
Hi-Resolution Audio Compliant
Designed to match perfectly with the R-Series subwoofers (12, 10, and 8-inch sizes available) and the new R-Series speakers.
Fuse Rating: 30A x 2
Approximate Weight: 11 lbs
Dimensions: 10-3/4" W x 2-1/16" H x 10" D
Authorized Dealer
1-year Manufacturer's Warranty
What's in the box:
4-Channel amplifier
Two 30-amp ATO fuses (installed)
4 Mounting feet
Four 3/4" Screws
Eight M2.5x5.5mm Machine screws
2mm Allen wrench
3mm Allen wrench
Owner's manual (English/ French/ Spanish)
Alpine Verification Certificate
Warranty information
Power supply note
Online product registration information
Alpine R-A60F owner's manual
⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov
00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate Prime R250X4 250 Watt 4-Channel Class AB Car Audio Amplifier
$279.99
$350.00
Rockford Fosgate Prime Series R250X4 250 Watts RMS, 4-Channel Class AB Car Audio AmplifierThe Prime R250X4 is a 250-watt 4-channel amplifier capable of running 2-Ohms stereo on all channels and 4-Ohms bridged/mono on the rear channels. Includes on-board Punch Bass and front/rear crossover controls. The Prime R250X4 is a 4-Channel amplifier perfect for any Car Audio Fanatic getting into mobile audio wanting a single amplifier to run a complete audio system. This amplifier features selectable Punch Bass to tune low frequencies, variable crossovers to either protect your high-frequency speakers or feeding only bass to your subwoofers.General Features:
4-channel car amplifier
40 watts RMS x 4 at 4 ohms (60 watts RMS x 4 at 2 ohms)
125 watts RMS x 2 bridged output at 4 ohms (4-ohm stable in bridged mode)
CEA-2006 Compliant
variable high- and low-pass filters (50-250 Hz, 12 dB/octave) on front and rear channels
selectable bass boost (0, 6, 12 dB at 45 Hz)
Class-AB amplifier design
MOSFET power supply
frequency response: 20-20K Hz
preamp and speaker-level inputs
8-gauge power and ground leads and a 50-amp fuse recommended — wiring and hardware not included with amplifier
no onboard fuses — when installing multiple amps in a system, an additional 50-amp in-line fuse between the distribution block and this amplifier is recommended
Dimensions: 11-1/4"W x 2-1/16"H x 6-13/16"D
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca
00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate R250X4 Prime 250 Watts 4-Channel Amplifier + 4 Gauge Amp Kit
$429.99
$800.00
Rockford Fosgate Prime Series R250X4 250 Watts RMS, 4-Channel Class AB Car Audio Amplifier + Absolute 4 Gauge Amp KitThe Prime R250X4 is a 250-watt 4-channel amplifier capable of running 2-Ohms stereo on all channels and 4-Ohms bridged/mono on the rear channels. Includes on-board Punch Bass and front/rear crossover controls. The Prime R250X4 is a 4-Channel amplifier perfect for any Car Audio Fanatic getting into mobile audio wanting a single amplifier to run a complete audio system. This amplifier features selectable Punch Bass to tune low frequencies, variable crossovers to either protect your high-frequency speakers or feeding only bass to your subwoofers.General Features:
4-channel car amplifier
40 watts RMS x 4 at 4 ohms (60 watts RMS x 4 at 2 ohms)
125 watts RMS x 2 bridged output at 4 ohms (4-ohm stable in bridged mode)
CEA-2006 Compliant
variable high- and low-pass filters (50-250 Hz, 12 dB/octave) on front and rear channels
selectable bass boost (0, 6, 12 dB at 45 Hz)
Class-AB amplifier design
MOSFET power supply
frequency response: 20-20K Hz
preamp and speaker-level inputs
8-gauge power and ground leads and a 50-amp fuse recommended — wiring and hardware not included with amplifier
no onboard fuses — when installing multiple amps in a system, an additional 50-amp in-line fuse between the distribution block and this amplifier is recommended
Dimensions: 11-1/4"W x 2-1/16"H x 6-13/16"D
⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov
00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate Prime R2-250X1 Mono Subwoofer Amplifier
$229.99
$350.00
Rockford Fosgate R2-250X1 Prime Series mono subwoofer amplifier 250-Watt Monoblock Amplifier
Rockford Fosgate's R2 amplifiers are the building blocks for great audio systems, powerful enough even to DRIVE our Punch speakers and subwoofers. They have undergone an amazing upgrade by packing them with the latest features at incredible value. Best of all, they are designed and engineered here in Tempe, Arizona.
Primed for performance, the R2-250X1 is a 250-watt, class-D amplifier capable of operating at 4Ω or 2Ω mono. This amplifier is extremely efficient because of its class-D technology, which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. Perfect for subwoofers, a variable infrasonic filter, and remote level control allows you to tune the bass for the desired level of the music.
General Features:
Rockford Fosgate Prime R2-250X1
Class-D Full-Range Monoblock Amplifier
320 watts x 1 channel @ 4 Ohms RMS Power
600 watts x 2 channel @ 2 Ohms RMS Power
Total power output: 250 watts
Balanced Differential Inputs with RCA Pass Through Outputs
High-Level Input Capable
Defeat able Auto Turn-On Circuit
Features C.L.E.A.N. Set-up
Variable Input Gain adjustment level
R.L.C. Remote Level Control
Variable Infrasonic Filter
Continuously Variable On Board Punch EQ
Top Mounted Control Panel
Short Circuit & Over Current Protection
CEA-2006 Compliant & CE Compliant
Full-Range, Class D
Rollback Protection
Input Sensitivity:
Low-Level: 150 mV - 4 V
High-Level: 450 mV - 12 V
Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers
Frequency Response: 20 Hz - 250 Hz
Total Harmonic Distortion (THD): >1%
Crossover Controls:
Low-Pass: 50 Hz - 250 Hz
Sub Infrasonic: 15 Hz - 40 Hz
Recommended Fuse Rating: 50A
Dimensions: "1.9" x "6.8" x "8.1"
Authorized Internet Dealer
1-year Manufacturer's Warranty
What is in the R2S-1X12 package:
R2S-1X12 owner's manual
Sealed enclosure loaded with one 12" woofer
2 Mounting brackets
Four 3/4" Self-tapping screws
Installation and operation instructions
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca
00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate M2-500X1 Monoblock Marine Amplifier with Absolute KIT4 4 Gauge Amp Kit
$329.99
$699.98
Rockford Fosgate M2-500X1 Monoblock Marine Amplifier with Absolute KIT4 4 Gauge Amp Kit
Rockford Fosgate M2-500X1 500 Watt Monoblock marine amplifierDesigned to withstand the elements, the M2-500X1 Element Ready™ amplifier is a 500 watt, class-D model, capable of operating at 4Ω or 2Ω mono. This amplifier is extremely efficient because of its class D technology which reduces demand on the electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allow you to tune the bass for the desired level for the music.
General Features:
Element Ready™ design protects against outdoor exposure
Conformal coated circuit board protects against dust and water
UV stable powder-coated cast aluminum heatsink
Zinc Nickel-plated Marine grade brass connection terminals
C.L.E.A.N. input/output clip detection and indicator LEDs
MEHSA 4 (Maximum Efficiency Heat Sink Application)
NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances.
Optimized using AudioGraph PowerCube measurement tool
Continuously Variable On Board Punch EQ
Includes RLC Remote Level Control
Focused mass heatsink design
Top Mounted Control Panel
Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers
Short Circuit & Over Current Protection
Variable Infrasonic Filter
Integrated Power and Speaker Terminals
Balanced Differential Inputs via Speaker Line or RCA Inputs
RCA pass-thru outputs
Integration with OEM and Aftermarket Radios
"Auto-Sense" turn-on with remote out (high level in)
Auto-Sense bypass switch for vehicles with RAP (Retained Accessory Power)
Low Impedance Stability
Proprietary testing using RATS (Rockford Automated Testing System)
CEA-2006 Compliant & CE Compliant
Rollback Protection
Power Ratings: 300 Watts x 1 @ 4 ohms
Power Ratings: 500 Watts x 1 @ 2 ohms
Dynamic Power Ratings: 350 Watts x 1 @ 4 ohms
Dynamic Power Ratings: 590 Watts x 1 @ 2 ohms
Frequency Response: 20 Hz - 250 Hz
Low-Level Input Sensitivity: 150 mV - 4 V
High-Level Input Sensitivity: 450 mV - 12 V
Total Harmonic Distortion (THD+Noise): <1.0%
Low-Level Signal Input: 2 RCA
High-Level Input Signal: 4-Pin Molex
Low-Level Signal Output: 2 RCA (Pass-Thru active with RCA or Hi-Level input)
Tone-Controls: 0 to +18 dB @ 45 Hz
Low-Pass Crossover Controls: 50 Hz - 250 Hz @ 12dB/Octave Butterworth
Infrasonic Crossover Controls: 15 Hz - 40 Hz @ 12dB/Octave Butterworth
4 gauge power and ground wiring is recommended for installation. Contact us for information regarding a discount on select amplifier kits from our website when purchased together with this amplifier.
Dimensions: 1.9"W x 6.8"D x 8.5"H
Authorized Internet Dealer
1-year Manufacturer's Warranty
⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca
00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate M2-500X1 Monoblock Marine Amplifier
$319.99
$599.98
Rockford Fosgate M2-500X1 Monoblock Marine Amplifier
Rockford Fosgate M2-500X1 500 Watt Monoblock marine amplifierDesigned to withstand the elements, the M2-500X1 Element Ready™ amplifier is a 500 watt, class-D model, capable of operating at 4Ω or 2Ω mono. This amplifier is extremely efficient because of its class D technology which reduces demand on the electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allow you to tune the bass for the desired level for the music.
General Features:
Element Ready™ design protects against outdoor exposure
Conformal coated circuit board protects against dust and water
UV stable powder-coated cast aluminum heatsink
Zinc Nickel-plated Marine grade brass connection terminals
C.L.E.A.N. input/output clip detection and indicator LEDs
MEHSA 4 (Maximum Efficiency Heat Sink Application)
NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances.
Optimized using AudioGraph PowerCube measurement tool
Continuously Variable On Board Punch EQ
Includes RLC Remote Level Control
Focused mass heatsink design
Top Mounted Control Panel
Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers
Short Circuit & Over Current Protection
Variable Infrasonic Filter
Integrated Power and Speaker Terminals
Balanced Differential Inputs via Speaker Line or RCA Inputs
RCA pass-thru outputs
Integration with OEM and Aftermarket Radios
"Auto-Sense" turn-on with remote out (high level in)
Auto-Sense bypass switch for vehicles with RAP (Retained Accessory Power)
Low Impedance Stability
Proprietary testing using RATS (Rockford Automated Testing System)
CEA-2006 Compliant & CE Compliant
Rollback Protection
Power Ratings: 300 Watts x 1 @ 4 ohms
Power Ratings: 500 Watts x 1 @ 2 ohms
Dynamic Power Ratings: 350 Watts x 1 @ 4 ohms
Dynamic Power Ratings: 590 Watts x 1 @ 2 ohms
Frequency Response: 20 Hz - 250 Hz
Low-Level Input Sensitivity: 150 mV - 4 V
High-Level Input Sensitivity: 450 mV - 12 V
Total Harmonic Distortion (THD+Noise): <1.0%
Low-Level Signal Input: 2 RCA
High-Level Input Signal: 4-Pin Molex
Low-Level Signal Output: 2 RCA (Pass-Thru active with RCA or Hi-Level input)
Tone-Controls: 0 to +18 dB @ 45 Hz
Low-Pass Crossover Controls: 50 Hz - 250 Hz @ 12dB/Octave Butterworth
Infrasonic Crossover Controls: 15 Hz - 40 Hz @ 12dB/Octave Butterworth
Dimensions: 1.9"W x 6.8"D x 8.5"H
Authorized Internet Dealer
1-year Manufacturer's Warranty
⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca
00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate Punch R2-1200X1 Prime 2400 Watt 1 OHM Mono Amplifier Class D
$379.99
$699.99
Rockford Fosgate Prime R2-1200X1 mono amplifier 1200W RMS x 1 at 1-ohm monoblock subwoofer amplifier
Primed for performance, the R2-1200X1 is a 1200-watt, class-D amplifier capable of operating at 4Ω, 2Ω, or 1Ω mono. This amplifier is extremely efficient because of its class-D technology, which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allow you to tune the bass for the desired level of the music.
General Features:
Rockford Fosgate Prime R2-1200X1
Class-D Full Range Monoblock Amplifier
RMS Power Rating:
4 ohms: 400 watts x 1 chan.
2 ohms: 800 watts x 1 chan.
1 ohm: 1200 watts x 1 chan.
Balanced Differential Inputs with RCA Pass Through Outputs
High-Level Input Capable
Defeatable Auto Turn on Circuit
Features C.L.E.A.N. Set-up
Variable Input Gain adjustment level
R.L.C. Remote Level Control
Variable Infrasonic Filter
Continuously Variable On-Board Punch EQ
Top Mounted Control Panel
Short Circuit & Over Current Protection
CEA-2006 Compliant & CE Compliant
Full Range Class D
Rollback Protection
Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers
Input sensitivity:
Low-Level: 150 mV - 4 V
High-Level: 450 mV - 12 V
Frequency Response: 20 Hz - 250 Hz
Total Harmonic Distortion (THD): >1%
Low-Pass: 50 Hz - 250 Hz @ 12dB
Sub Infrasonic: 15 Hz - 40 Hz
Fuse Rating: 120A
4-gauge power and ground wiring are recommended for installation.
Dimensions: 1.9" x 6.8" x 11.3"
Authorized Internet Dealer
1-year Manufacturer's Warranty
What is in the R2-1200X1 package:
Mono subwoofer amplifier
Wired Remote Level Control module
16' Remote cable (RJ-25 connector on both ends)
One 7" Speaker input harness
3mm Allen Hex key
Four 3/4" Screws
Two 1/2" Screws
5 Flat washers
1 Nut
Installation and Operation Instructions
Certificate of Performance
R2-1200X1 owner’s manual
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.