2-Channel Amplifiers (58)

Rockford Fosgate Punch P300X2 300W RMS Punch Series 2-Channel Stereo Class AB Car Power Amplifier The Punch P300X2 is a 2-channel stereo amplifier capable of producing 150 Watts into each channel at 2-Ohms. The P300X2 amplifier is great to drive a pair of coaxial speakers, component speakers, or a single subwoofer. The amplifier can also be run in stereo/mono mode simultaneously when using passive crossovers (not supplied) on all speakers. With proven PUNCH technology, the P300X2 delivers real Rockford Fosgate power from a small design and is flexible to accommodate any moderately sized system. General Features: Punch Series 2-Channel Class AB Car Amplifier RMS Power Rating: 4 ohms: 100 watts x 2 Channel 2 ohms: 150 watts x 2 Channel Bridged, 4 ohms: 300 watts x 1 chan. CEA-2006 compliant amplifier Features C.L.E.A.N. Set-up with input/output clip detection and indicator LEDs MOSFET power supply Muted turn on Cast aluminum heatsink 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protect indicators Nickel-plated captive C-clamp terminals Ultra-efficient Class BD circuitry to maximize amplifier power efficiency On-board differential inputs eliminate noise picked up by the signal cable Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately) MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowers the operating temperature and potential for noise - similar to circuit boards designed by aerospace manufacturers Input sensitivity: 150mV - 12V What is in the box: 2-Channel amplifier Four 1-1/2" Screws 5mm Allen wrench Quick setup instructions Certificate of Performance Rockford Fosgate Punch P300X2 owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca

Rockford Fosgate Punch P300X2 300W RMS Punch Series 2-Channel Stereo Class AB Car Power Amplifier The Punch P300X2 is a 2-channel stereo amplifier capable of producing 150 Watts into each channel at 2-Ohms. The P300X2 amplifier is great to drive a pair of coaxial speakers, component speakers, or a single subwoofer. The amplifier can also be run in stereo/mono mode simultaneously when using passive crossovers (not supplied) on all speakers. With proven PUNCH technology, the P300X2 delivers real Rockford Fosgate power from a small design and is flexible to accommodate any moderately sized system. General Features: Punch Series 2-Channel Class AB Car Amplifier RMS Power Rating: 4 ohms: 100 watts x 2 Channel 2 ohms: 150 watts x 2 Channel Bridged, 4 ohms: 300 watts x 1 chan. CEA-2006 compliant amplifier Features C.L.E.A.N. Set-up with input/output clip detection and indicator LEDs MOSFET power supply Muted turn on Cast aluminum heatsink 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protect indicators Nickel-plated captive C-clamp terminals Ultra-efficient Class BD circuitry to maximize amplifier power efficiency On-board differential inputs eliminate noise picked up by the signal cable Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately) MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowers the operating temperature and potential for noise - similar to circuit boards designed by aerospace manufacturers Input sensitivity: 150mV - 12V What is in the box: 2-Channel amplifier Four 1-1/2" Screws 5mm Allen wrench Quick setup instructions Certificate of Performance Rockford Fosgate Punch P300X2 owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca

Rockford Fosgate Punch PBR300X2 Compact 2-channel car amplifier 100 watts RMS x 2 You won't believe how small and powerful this amp is. Rockford Fosgate's PBR300X2 2-channel amp puts out 100 watts RMS each to a pair of speakers, all from an amp you can easily hold in one hand. You can also put this amp in one-channel mode to drive a sub with 300 watts RMS of bumping bass. And an optional wired remote control lets you add Rockford Fosgate's famous extra Punch from the front seat. Boosted Rail (BR) amp technology This Punch Class BR amplifier uses Boosted Rail (BR) amp technology to generate so much power from such a tiny case, with capacitors and high-speed circuitry that boost the amp's power supply voltage when needed, so it can handle musical peaks without missing a beat. Rockford Fosgate uses this new technology to create a remarkable amp that fits almost anywhere and delivers powerful sound. Heat management The amp also features speaker-level inputs with signal-sensing turn-on, allowing you to connect into almost any system without having to run a turn-on lead back to the receiver. An extruded aluminum heat sink combines with Rockford Fosgate's heat management technology to make sure your tunes keep rockin' — even when you're playing loud. Product highlights: 2-channel car amplifier 100 watts RMS x 2 at 4 ohms (150 watts RMS x 2 at 2 ohms) 300 watts RMS x 1 bridged output at 4 ohms (4-ohm stable in bridged mode) CEA-2006 compliant Boosted Rail amp technology Dynamic Thermal Management cooling system variable high- and low-pass filters (50-500 Hz, 12 dB/octave) differential-balanced inputs eliminate noise from your vehicle's electrical system preamp and speaker-level inputs optional wired PEQ remote (0-18 dB at 45 Hz and 0-12 dB at 12K Hz) 10-gauge power and ground leads and a 30-amp fuse recommended — wiring and hardware not included with amplifier no onboard fuses — when installing multiple amps in a system, an additional 30-amp in-line fuse between the distribution block and the amplifier is recommended dimensions: 6-3/4"W x 1-9/16"H x 4-1/4"D warranty: 1 year (extends to 2 years when purchased and used with Rockford Fosgate's RFK10 or RFK10i amp wiring kit) ⚠️Warning: Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Rockford Fosgate Punch P300X2 2-channel car amplifier 100 watts RMS x 2 Big power for your speakers or subRockford Fosgate's Punch P300X2 amplifier sends 100 watts RMS per channel to your speakers, filling your ride with clean music. You can use the high-pass filter to keep the low bass out of your speakers so they perform more efficiently. You can also switch this versatile amp into mono mode to drive a subwoofer with up to 300 watts RMS, then use the built-in low-pass filter to send the correct bass frequencies to your sub. The Punch EQ2 features bass and treble boosts, in case you want to add a little boom or sizzle back into the mix. Easy to set for optimum performanceOnce again, Rockford Fosgate steps away from the crowd with their C.L.E.A.N. technology (Calibrated Level Eliminates Audible Noise) — a setup system that ensures your music will sound as clean and powerful as possible. It works like this: first download the setup tones from Rockford Fosgate, then play the tone, adjust the receiver volume until a red clip light on the amp goes out, then turn the amp gain up until a blue light comes on. It's that simple — your amplifier will be perfectly set to match your receiver's output. When your receiver reaches maximum clean volume, you'll get maximum clean power from your Power amp. At quiet listening levels, you'll hear less background noise and more of your music. Keeps an eye on things while playingIf that blue light turns solid red while you're playing music, the amp's telling you that your source is distorting and you should turn it down, or risk damage to your gear. The optional PLC2 remote level control also doubles as a clip indicator, so you can see from the front seat if your music's clipping. The amp's built-in computer keeps tabs on the output current, ensuring that plunging speaker impedances (they change during play) or even a short circuit won't hurt anything. Maintaining coolness raises efficiency and lowers distortionRockford Fosgate's Dynamic Thermal Management system uses forced air to dissipate heat evenly across the amp and out through the high-mass heatsink, efficiently drawing heat away from vital internal parts. Their proprietary MEHSA cooling process maximizes the heat transfer from the MOSFET devices to the heatsink, allowing the heat to escape more readily, so the transistors stay cooler and work better. Product highlights: 2-channel car amplifier 100 watts RMS x 2 at 4 ohms (150 watts RMS x 2 at 2 ohms) 300 watts RMS x 1 bridged at 4 ohms (4-ohm stable in bridged mode) CEA-2006 compliant Features: variable high- and low-pass filter filter (50-250 Hz, 12 dB/octave) variable PEQ2 bass/treble boost (0-18 dB at 45 Hz and 0-14 dB at 12.5K Hz) C.L.E.A.N. gain setup system includes clip lights and link to Rockford Fosgate's setup tones Class-AB amplifier design frequency response: 20-20,000 Hz Dynamic Thermal Management and MEHSA MOSFET cooling systems MOSFET power and output stages preamp inputs and outputs speaker-level inputs (speaker wire to RCA adapter required) signal-sensing turn-on with speaker-level inputs eliminate need for remote turn-on lead More Info: optional PLC2 wired remote level control with clip light available 8-gauge power and ground leads and an 50-amp fuse recommended — wiring and hardware not included with amplifier no onboard fuses — when installing multiple amps in a system, an additional 50-amp in-line fuse between the distribution block and the amplifier is recommended 9-15/16"W x 2-7/16"H x 8-13/16"D warranty: 1 year ⚠️Warning: Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Rockford Fosgate Punch P500X2 2-channel car amplifier 150 watts RMS x 2 Big power for your speakers or subRockford Fosgate's Punch P500X2 amplifier sends 150 watts RMS per channel to your speakers, filling your ride with clean music. You can use the high-pass filter to keep the low bass out of your speakers so they perform more efficiently. You can also switch this versatile amp into mono mode to drive a subwoofer with up to 500 watts RMS, then use the built-in low-pass filter to send the correct bass frequencies to your sub. The Punch EQ2 features bass and treble boosts, in case you want to add a little boom and sizzle back into the mix. Easy to set for optimum performanceOnce again, Rockford Fosgate steps away from the crowd with their C.L.E.A.N. technology (Calibrated Level Eliminates Audible Noise) — a setup system that ensures your music will sound as clean and powerful as possible. It works like this: first download the setup tones from Rockford Fosgate, then play the tone, adjust the receiver volume until a red clip light on the amp goes out, then turn the amp gain up until a blue light comes on. It's that simple — your amplifier will be perfectly set to match your receiver's output. When your receiver reaches maximum clean volume, you'll get maximum clean power from your Power amp. At quiet listening levels, you'll hear less background noise and more of your music. Keeps an eye on things while playingIf that blue light turns solid red while you're playing music, the amp's telling you that your source is distorting and you should turn it down, or risk damage to your gear. The optional PLC2 remote level control also doubles as a clip indicator, so you can see from the front seat if your music's clipping. The amp's built-in computer keeps tabs on the output current, ensuring that plunging speaker impedances (they change during play) or even a short circuit won't hurt anything. Maintaining coolness raises efficiency and lowers distortionRockford Fosgate's Dynamic Thermal Management system uses forced air to dissipate heat evenly across the amp and out through the high-mass heatsink, efficiently drawing heat away from vital internal parts. Their proprietary MEHSA cooling process maximizes the heat transfer from the MOSFET devices to the heatsink, allowing the heat to escape more readily, so the transistors stay cooler and work better.Product highlights: 2-channel car amplifier 150 watts RMS x 2 at 4 ohms (250 watts RMS x 2 at 2 ohms) 500 watts RMS x 1 bridged at 4 ohms (4-ohm stable in bridged mode) CEA-2006 compliant Features: variable high- and low-pass filter filter (50-250 Hz, 12 dB/octave) variable PEQ2 bass/treble boost (0-18 dB at 45 Hz and 0-14 dB at 12.5K Hz) C.L.E.A.N. gain setup system includes clip lights and link to Rockford Fosgate's setup tones Class-AB amplifier design frequency response: 20-20,000 Hz Dynamic Thermal Management and MEHSA MOSFET cooling systems MOSFET power and output stages preamp inputs and outputs speaker-level inputs (speaker wire to RCA adapter required) signal-sensing turn-on with speaker-level inputs eliminate need for remote turn-on lead More Info: optional PLC2 wired remote level control with clip light available 4-gauge power and ground leads and an 80-amp fuse recommended — wiring and hardware not included with amplifier no onboard fuses — when installing multiple amps in a system, an additional 80-amp in-line fuse between the distribution block and the amplifier is recommended 13-3/8"W x 2-7/16"H x 8-13/16"D warranty: 1 year ⚠️Warning: Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Rockford Fosgate Punch P1000X2 2-channel car amplifier 300 watts RMS x 2 Big power for your speakers or subwoofersRockford Fosgate's Punch P1000X2 amplifier sends 300 watts RMS to each of a pair of high-performance speakers or subs, filling your ride with plenty of loud, clean music. You can use the high-pass filter to keep the low bass out of your speakers so they perform more efficiently. You can also switch this versatile amp into mono mode to drive a sub with up to 1000 watts RMS, then use the built-in low-pass filter to send the correct bass frequencies to your sub. The Punch EQ2 features a bass and treble boost, in case you want to add a little boom and sizzle back into the mix. Easy to set for optimum performanceOnce again, Rockford Fosgate steps away from the crowd with their C.L.E.A.N. technology (Calibrated Level Eliminates Audible Noise) — a setup system that ensures your music will sound as clean and powerful as possible. It works like this: first download the setup tones from Rockford Fosgate, then play the tone, adjust the receiver volume until a red clip light on the amp goes out, then turn the amp gain up until a blue light comes on. It's that simple — your amplifier will be perfectly set to match your receiver's output. When your receiver reaches maximum clean volume, you'll get maximum clean power from your Power amp. At quiet listening levels, you'll hear less background noise and more of your music. Keeps an eye on things while playingIf that blue light turns solid red while you're playing music, the amp's telling you that your source is distorting and you should turn it down, or risk damage to your gear. The optional PLC2 remote level control also doubles as a clip indicator, so you can see from the front seat if your music's clipping. The amp's built-in computer keeps tabs on the output current, ensuring that plunging speaker impedances (they change during play) or even a short circuit won't hurt anything. Maintaining coolness raises efficiency and lowers distortionRockford Fosgate's Dynamic Thermal Management system uses forced air to dissipate heat evenly across the amp and out through the high-mass heatsink, efficiently drawing heat away from vital internal parts. Their proprietary MEHSA cooling process maximizes the heat transfer from the MOSFET devices to the heatsink, allowing the heat to escape more readily, so the transistors stay cooler and work better. Product highlights: 2-channel car amplifier 300 watts RMS x 2 at 4 ohms (500 watts RMS x 2 at 2 ohms) 1000 watts RMS x 1 bridged at 4 ohms (4-ohm stable in bridged mode) CEA-2006 compliant Features: variable high- and low-pass filter filter (50-250 Hz, 12 dB/octave) variable PEQ2 bass/treble boost (0-18 dB at 45 Hz and 0-14 dB at 12.5K Hz) C.L.E.A.N. gain setup system includes clip lights and link to Rockford Fosgate's setup tones Class-AB amplifier design frequency response: 20-20K Hz Dynamic Thermal Management and MEHSA MOSFET cooling systems MOSFET power and output stages preamp inputs and outputs speaker-level inputs (speaker wire to RCA adapter required) signal-sensing turn-on with speaker-level inputs eliminate need for remote turn-on lead More Info: optional PLC2 wired remote level control with clip light available 4-gauge power and ground leads and an 140-amp fuse recommended — wiring and hardware not included with amplifier no onboard fuses — when installing multiple amps in a system, an additional 140-amp in-line fuse between the distribution block and the amplifier is recommended 15-1/8"W x 2-7/16"H x 7-13/16"D warranty: 1 year ⚠️Warning: Cancer and Reproductive Harm-www.P65Warnings.ca.gov