10" Car Subwoofer (189)

2 Alpine S-W10D2 1800W Max (600W RMS) 10" S-Series Dual 2 Ohm Car Subwoofer  with Absolute TW500 Tweeter & Absolute BT1700 Electrical Tape & Mobile Magnet Holder Alpine introduces the all-new S-Series Subwoofers. Their unique design substantially improves bass output and provides installation versatility. Each S-Series subwoofer uses a custom-stamped steel frame and is available in twelve, ten, and eight-inch sizes. These high-strength frames were designed to withstand the rigors of the improved S-Series motor. They have frame leg vents, a vented back plate to help cool the subwoofer voice coil and motor parts, and a shallow design to help fit in smaller spaces. The S-Series Subwoofers incorporates two strontium ferrite magnets stacked together, providing increased motor strength and excursion and ultimately delivering accurate bass to your music. The convenient push-type insert terminals with a dual voice coil jumper system will significantly reduce installation time. Just strip the speaker insulation at the wire end, then insert the bare wire into the hole of the spring-loaded push terminal. At the same time, the concealed mount gasket system creates a clean, finished appearance for any vehicle. General Features: 10" 2 ohm S-Series (Type-S) Subwoofer RMS Power Handling: 600 watts Peak Power Handling: 1800 watts  Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 4-11/16" Cutout diameter: 8-13/16 Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 33 Hz Authorized Dealer 1-year Manufacturer's Warranty What is in the S-W10D2 package: S-W10D2 owner's manual One 10" Dual 2-ohm voice coil subwoofer 1 Rubber concealing ring Two 3" jumper cables (each has a single banana connector on each end) Subwoofer Application Guide Online product registration information Warranty Information Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine RS-SB10 10" Halo R-Series R2 Preloaded Subwoofer Enclosure with ProLink The next generation of sound performance is here with the new R-Series Halo Preloaded Subwoofers featuring the new R-Series “R2” subwoofers for more accurate and authoritative bass. PRODUCT FEATURES: Unique ProLink Design – ProLink is unique to Alpine and allows you to link two R2-SB10V enclosures together using an optional KTX-H10 linking kit to create a dual subwoofer enclosure. Stand Out in the Crowd – Drawing inspiration from the sleek, tapered lines and clean silver finish of the Alpine Halo display, the R2-SB10V shares the same unique, curved edges outlined by a silver trim and a metallic front baffle for a matching system aesthetic. Improved Performance – The new R-Series subwoofers now feature larger, double-stacked magnets that contribute more motor force for deeper bass and tighter bass control compared to the previous generation. General Specs: Size: 10” Weight: 42 lbs Dimensions: 16” x 12.68” x 14.5” Frequency Response: 26Hz - 200Hz Power Range: 300W - 750W RMS Power Handling: 750W RMS / 2250W Peak Magnet Weight: 123 oz Voice Coil Diameter: 65.5 mm (2.6”) Linear Excursion (Xmax): 20 mm T/S Parameters: Sensitivity (1W/1m): 82.3 dB DC Resistance (Re): 1.9Δ + 1.9Δ Free Air Resonance (Fs): 31 Hz Equivalent Stiffness: 18.2 L Mechanical Q (Qms): 7.07 Electrical Q (Qes): 0.5 Total Q (Qts): 0.47 Cone Area (Sd): 333 cm2 Linear Excursion (Xmax): 20 mm Mechanical Travel (Xmech): 70 mm The next generation of sound performance is here with the new R-Series Halo Preloaded Subwoofers featuring the new R-Series “R2” subwoofers for more accurate and authoritative bass. Unique ProLink Design – ProLink is unique to Alpine and allows you to link two R2-SB10V enclosures together using an optional KTX-H10 linking kit to create a dual subwoofer enclosure. Stand Out in the Crowd – Drawing inspiration from the sleek, tapered lines and clean silver finish of the Alpine Halo display, the R2-SB10V shares the same unique, curved edges outlined by a silver trim and a metallic front baffle for a matching system aesthetic. Improved Performance – The new R-Series subwoofers now feature larger, double-stacked magnets that contribute more motor force for deeper bass and tighter bass control compared to the previous generation.

Alpine R2-SB10V-BNDL Bass Boost Package Includes R2-SB10V 10" ported enclosure, S-A60M amplifier, and RUX-KNOB.2 remote level control package includes Alpine R2-SB10V Halo Series enclosure, S-A60M mono amplifier, and RUX-KNOB.2 remote level control Alpine R2-SB10V R-Series 10″ Halo Subwoofer with ProLink™ 2Ω A subwoofer enclosure that sounds as good as it looks. Alpine’s preloaded, linkable subwoofer enclosures give you powerful performance with the unique Alpine Halo design and ProLink™. The new 2nd generation R-Series subwoofers take bass performance to extreme levels, delivering thunderous, ground-pounding bass. With Alpine’s enhanced sound performance, the R-Series subwoofers are highly accurate, creating a perfectly matched sound system to R-Series amplifiers and R-Series speakers – building an overall cohesive theme with its entire full-range Hi-RES Audio certified system. The R2-SB10V is designed for amplifier compatibility with 20hm loads. General Features: Dual 10" Vented / Ported Subwoofer Enclosure Power Handling: Peak: 2250 watts Total RMS: 750 watts Total Preloaded with single 10" Subwoofers Vented / Ported Square/Rectangle enclosure Enclosure Dimensions: 14.5" TD x BD x 16" W x 12.68" H Groundbreaking Alpine Halo Design ProLink™ ported enclosure design Optimal Sound Performance Includes preloaded R-W10D4 10” R-Series subwoofer CARB-compliant 3/4-inch MDF construction Premium black carpet Silver Alpine embossed side logo badge Brushed aluminum finished metallic front baffle Authorized Internet Dealer 1-year Manufacturer's Warranty Subwoofer Features: Frequency Response: 24 - 200 Hz Sensitivity: 85 dB Enclosure Features: 10" Square/Rectangle Enclosure Box Finish: Carpet What's in the R2-SB10V package: R2-SB10V Owner's manual Ported enclosure loaded with one R2-W10D4 subwoofer driver Warranty information Product registration information Safety notice Alpine S-A60M S-Series Monoblock Class-D Amplifier 600W RMSThe Alpine S-Series Sound ComponentsThree new S-Series amplifiers join the S-Series family, known for reliable performance and value-oriented products. All three S-Series amps (mono, 4-channel, and 5-channel) contain technology currently implemented in R and X-Series models. The S-Series amps feature attractive prices and are designed to perform perfectly with the existing S-Series speakers.S-Series amplifiers are your sound system’s workhorse. With unmatched reliability and budget-friendly prices, these amplifiers are the better choice in performance value.General Features: Alpine S-Series Mono Power Amplifier - S-A60M RMS Power Output: 400W x 1 @ 4 Ohms (14.4V < 1% THD+N) 600W x 1 @ 2 Ohms (14.4V < 1% THD+N) S/N ratio: >85dB (ref: 1W into 4 ohms), >105dB (ref: rated power into 4 ohms) Remote bass knob compatible (requires RUX-KNOB.2, sold separately) CTA-2006 compliant THD+N ≤ 0.03% (ref 1W info 4 ohm) Frequency Response: 10HZ-400Hz (+/- 3 dB) Damping Factor: > 1000 variable low-pass filter (50-400 Hz, 24 dB/octave) variable bass boost (0-12 dB at 50 Hz) Speaker-level inputs (Speaker Wire to RCA Adapter Required) Preamp Inputs Improved heat sink and protection circuit design that eliminates thermal shut-down for dependable music playback Remote Sensing automatic turn-on when using speaker-level inputs Approximate Weight: 11 lbs Fuse Rating: fuse rating: 30A x 2 Four gauge power and ground wiring are recommended for installation. Contact us for information regarding a discount on select from our website when purchased together with this amplifier. Dimensions: 8” W x 8” H x 2.25” D Authorized Dealer 1-year Manufacturer's Warranty What's in the S-A60M package: S-A60M owner's manual Mono subwoofer amplifier Four 3/4" Screws 2mm Allen wrench Owner's manual Alpine Verification Certificate Online product registration information Alpine RUX-KNOB.2 Remote Bass Knob for Alpine Amplifiers General Features: Remote Bass Level Control Knob 16-1/2" (5 meters) Connection cable Plugs directly in for quick direct subwoofer control Specifically designed as the controller for use with any of the following PDX Amplifiers: PDX-M12, and PDX-M6 Easily adjust the bass gain of your amp while seated inside Control multiple amps from just one RUX-KNOB controller Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the package: Alpine Remote Bass Level Control module 16.4'  connecting cable  4 Self-tapping screws ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

  Alpine Halo R2-SB10V 750W RMS 10" Halo Series Linkable Ported Loaded Subwoofer Enclosure A subwoofer enclosure that sounds as good as it looks. Alpine’s preloaded, linkable subwoofer enclosures give you powerful performance with the unique Alpine Halo design and ProLink™. The new 2nd generation R-Series subwoofers take bass performance to extreme levels, delivering thunderous, ground-pounding bass. With Alpine’s enhanced sound performance, the R-Series subwoofers are highly accurate, creating a perfectly matched sound system for R-Series amplifiers and speakers – building an overall cohesive theme with its entire full-range Hi-RES Audio certified system. The R2-SB10V is designed for amplifier compatibility with 20hm loads. General Features: Dual 10" Vented / Ported Subwoofer Enclosure Power Handling: Peak: 2250 watts Total RMS: 750 watts Total Preloaded with single 10" Subwoofers Vented / Ported Square/Rectangle enclosure Enclosure Dimensions: 14.5" TD x BD x 16" W x 12.68" H Groundbreaking Alpine Halo Design ProLink™ ported enclosure design Optimal Sound Performance Includes preloaded R-W10D4 10” R-Series subwoofer CARB-compliant 3/4-inch MDF construction Premium black carpet Silver Alpine embossed side logo badge Brushed aluminum finished metallic front baffle Authorized Internet Dealer 1-year Manufacturer's Warranty Subwoofer Features: Frequency Response: 24 - 200 Hz Sensitivity: 85 dB Enclosure Features: 10" Square/Rectangle Enclosure Box Finish: Carpet What's in the R2-SB10V package: R2-SB10V Owner's manual Ported enclosure loaded with one R2-W10D4 subwoofer driver Warranty information Product registration information Safety notice ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

2 Absolute XS1000 Excursion Series 10" Flat Shallow Truck RV Car Audio Subwoofer Power Sub  General Features: 10" Single 4 Ohm Xcursion Series Slim Subwoofer Peak Power Handling: 1000 watts Impedance: 4 ohms Injected polypropylene poly-coated woofer cone for lower distortion Rubber woofer surround Metal basket with black painting Vented oversize back plate with extended pole piece Super slim shallow mount design 40 oz. Strontium magnet with rubber coating Sensitivity: 86 dB Includes decorative trim ring 1-year Manufacturer's warranty Recommended Enclosure Specifications: Recommended Enclosure Type: Ported / Vented, Sealed Minimum Sealed Box Volume: 0.5 cubic feet Maximum Sealed Box Volume: 1.08 cubic feet Minimum Ported Box Volume: 0.8 cubic feet Maximum Ported Box Volume: 0.8 cubic feet Top-Mount Depth (Mounting Depth): 4-1/2" Cutout Diameter: 9" Shallow Mount Installation: Yes Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Absolute XS1000 Excursion Series 10" Flat Shallow Truck RV Car Audio Subwoofer Power Sub  General Features: 10" Single 4 Ohm Xcursion Series Slim Subwoofer Peak Power Handling: 1000 watts Impedance: 4 ohms Injected polypropylene poly-coated woofer cone for lower distortion Rubber woofer surround Metal basket with black painting Vented oversize back plate with extended pole piece Super slim shallow mount design 40 oz. Strontium magnet with rubber coating Sensitivity: 86 dB Includes decorative trim ring 1-year Manufacturer's warranty Recommended Enclosure Specifications: Recommended Enclosure Type: Ported / Vented, Sealed Minimum Sealed Box Volume: 0.5 cubic feet Maximum Sealed Box Volume: 1.08 cubic feet Minimum Ported Box Volume: 0.8 cubic feet Maximum Ported Box Volume: 0.8 cubic feet Top-Mount Depth (Mounting Depth): 4-1/2" Cutout Diameter: 9" Shallow Mount Installation: Yes Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine RS-W10D2 12" 1200 Watts Shallow Mount Dual 2-Ohm Voice Coil R Series subwooferAlpine's RS-W10D2 R-Series With an ultra-shallow subwoofer design and powerful sound output, the R-Series Shallow Subwoofers give you the best of both worlds in size and sound. General Features: 10" Dual 2 ohms Type-R Series Shallow Subwoofer Peak Power Handling: 1200 watts RMS Power Handling: 600 watts Polypropylene with aluminum dust cap Cone Butyl Rubber Surround Alpine Gen2 DD Linear Magnetic Circuit Cast aluminum basket 4" High-Temperature Voice coil 20 mm Xmax Neodymium magnet motor structure Frequency Response: 29 - 200 Hz Resonance Frequency (Fs): 28 Hz Sensitivity: 81 dB Top-mount depth: 3.25" Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the RS-W10D2 package: RS-W10D2 Owner's Manual 10" R-Series Shallow Subwoofer Warranty Information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.