10" Car Subwoofer (163)

2 Rockford Fosgate Punch P2D2-10 10" Inch 1200 Watt Dual 2 Ohm Car Subwoofers Rockford Fosgate has always been known as "The PUNCH" and the P2 10" Punch car subwoofer certainly continues with the tradition. Kevlar fiber reinforced paper cones deliver bass impact you can feel along with VAST technology to increase surface cone area up to 25%. The P2 10-inch subwoofers perform best in standard sealed and vented enclosures. Includes diamond cut cast aluminum trim ring. Optional grille insert available.General Features: 10" Dual 2 ohm Punch Stage 2 Subwoofer Power Handling: Peak: 600 watts Power Handling: RMS: 300 watts Recommended power range: 250 - 375 watts RMS CEA-2031 Compliant Klippel Verified Flex-fit Mounting pattern Proprietary spider venting/cooling technique StampCast basket with integrated spider venting Sturdy 16 gauge compound bend frame geometry High modulus Kevlar re-inforced paper-pulp cone Semi-flexible, PVC removable protective motor cover Multi-point high-temp/high-strength neck joint bonding technique Tall-profile VAST Santoprene surround for larger surface area Dual tear & fatigue resistant poly-cotton spider with woven tinsel leads Fatigue resistant and reduced strain "stitched on" flexible lead wire design Proprietary all-metal, radially oriented compression input terminal assembly Optimized motor magnetics with extended pole and bumped vented backplate High temp 2.25" voice coil w/ spun-laced Nomex insulating reinforcement collar Die-Cast aluminum soft-touch painted trim ring allows for optional integrated grill Stamped Mesh Grille Insert Available: Rockford Fosgate P2P3G-10 Rockford Fosgate P2 Series Mounting Depth: 5.92" Cutout Diameter: 9.13" Magnet Weight: 66.40 oz Frequency Response: 29 - 250 Hz Xmax: 11.0 mm Sensitivity: 84 dB @ 1 watt / 1 meter Recommended Ported Enclosure: 1.40ft³ @40.0 Hz Recommended Sealed Enclosure: 0.59ft³ @46.6 Hz Matching Amplifiers: (one driver) Matching Amplifiers: (one driver) Rockford Fosgate R500X1D, Series @4ohms Matching Amplifiers: (one driver) Rockford Fosgate P300X2 (bridged), Series @4ohms Matching Amplifiers: (one driver) Rockford Fosgate P400X1, Series @4ohms Matching Amplifiers: (one driver) Rockford Fosgate R750-1D, Series @4ohms Matching Amplifiers: (one driver) Rockford Fosgate P1000X1BD, Series @4ohms Matching Amplifier: (two drivers) Rockford Fosgate R500X1D, Series/Parallel @2ohm Matching Amplifier: (two drivers) Rockford Fosgate R750-1D, Series/Parallel @2ohm Matching Amplifier: (two drivers) Rockford Fosgate P1000X1BD, Series/Parallel @2ohm Authorized Internet Dealer 1-year Manufacturer's Warranty ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca

2 Rockford Fosgate P2D2-10 10" 1200W Car Audio Subwoofer Subwoofer Rockford Fosgate has always been known as "The PUNCH," and the P2 10" subwoofer continues this tradition. Kevlar fiber-reinforced paper cones deliver a bass impact you can feel, and VAST technology increases surface cone area by up to 25%. The P2 subwoofers perform best in standard sealed and vented enclosures. They include a diamond-cut cast aluminum trim ring. An optional grille insert is available. General Features: 10" Dual 2 ohm Punch Stage 2 Subwoofer Power Handling: RMS: 300 watts Power Handling: Peak: 600 watts Recommended power range: 250 - 375 watts RMS CEA-2031 Compliant Klippel Verified Flex-fit Mounting pattern Proprietary spider venting/cooling technique StampCast basket with integrated spider venting Sturdy 16 gauge compound bend frame geometry High modulus Kevlar re-inforced paper-pulp cone Semi-flexible, PVC removable protective motor cover Multi-point high-temp/high-strength neck joint bonding technique Tall-profile VAST Santoprene surround for a larger surface area Dual tear & fatigue resistant poly-cotton spider with woven tinsel leads Fatigue-resistant and reduced strain "stitched on" flexible lead wire design Proprietary all metal, radially oriented compression input terminal assembly Optimized motor magnetics with extended pole and bumped vented backplate High temp 2.25" voice coil w/ spun-laced Nomex insulating reinforcement collar Die-cast aluminum soft-touch painted trim ring allows for optional integrated grill Stamped Mesh Grille Insert Available: Rockford Fosgate P2P3G-10 Mounting Depth: 5.92" Cutout Diameter: 9.13" Magnet Weight: 66.40 oz Frequency Response: 30.8 - 250 Hz Xmax: 11.0 mm Sensitivity: 84 dB @ 1 watt / 1 meter Recommended Ported Enclosure: 1.40ft³ @38.5 Hz Recommended Sealed Enclosure: 0.59ft³ @43.1 Hz Shipping Weight: 13.6 Lbs. Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the P2D2-10: Rockford Fosgate P2D2-10 owner's manual One 10" Dual 4-ohm voice coil subwoofer Trim ring Eight 1-1/8" Allen head screws 4mm Allen head bit Installation/Operation manual Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

2 Rockford Fosgate P2D4-10 10" 1200W Car Audio Subwoofer Subwoofer Rockford Fosgate has always been known as "The PUNCH" and the P2 10" subwoofer continues with the tradition. Kevlar fiber-reinforced paper cones deliver bass impact you can feel along with VAST technology to increase surface cone area up to 25%. The P2 subwoofers perform best in standard sealed and vented enclosures. Includes diamond cut cast aluminum trim ring. Optional grille insert available. General Features: 10" Dual 4 ohm Punch Stage 2 Subwoofer Power Handling: RMS: 300 watts Power Handling: Peak: 600 watts Recommended power range: 250 - 375 watts RMS CEA-2031 Compliant Klippel Verified Flex-fit Mounting pattern Proprietary spider venting/cooling technique StampCast basket with integrated spider venting Sturdy 16 gauge compound bend frame geometry High modulus Kevlar re-inforced paper-pulp cone Semi-flexible, PVC removable protective motor cover Multi-point high-temp/high-strength neck joint bonding technique Tall-profile VAST Santoprene surround for a larger surface area Dual tear & fatigue resistant poly-cotton spider with woven tinsel leads Fatigue-resistant and reduced strain "stitched on" flexible lead wire design Proprietary all metal, radially oriented compression input terminal assembly Optimized motor magnetics with extended pole and bumped vented backplate High temp 2.25" voice coil w/ spun-laced Nomex insulating reinforcement collar Die-Cast aluminum soft-touch painted trim ring allows for optional integrated grill Stamped Mesh Grille Insert Available: Rockford Fosgate P2P3G-10 Mounting Depth: 5.92" Cutout Diameter: 9.13" Magnet Weight: 66.40 oz Frequency Response: 30.8 - 250 Hz Xmax: 11.0 mm Sensitivity: 84 dB @ 1 watt / 1 meter Recommended Ported Enclosure: 1.40ft³ @38.5 Hz Recommended Sealed Enclosure: 0.59ft³ @43.1 Hz Shipping Weight: 13.6 Lbs. Authorized Internet Dealer 1-year Manufacturer's Warranty

Alpine S-W10D4 1800W Max (600W RMS) 10" S-Series Dual 4 Ohm Car Subwoofer Alpine introduces the all-new S-Series Subwoofers; their unique design substantially improves bass output and provides installation versatility. Each S-Series subwoofer uses a custom-stamped steel frame and is available in twelve, ten, and eight-inch. These high-strength frames were designed to withstand the rigors of the improved S-Series motor. They have frame leg vents, a vented back plate to help cool the subwoofer voice coil and motor parts, and a shallow design to help fit in smaller spaces. The S-Series Subwoofers incorporate two strontium ferrite magnets stacked together, providing increased motor strength and excursion, ultimately delivering an accurate bass to your music. The convenient push-type insert terminals with a dual voice coil jumper system will significantly reduce installation time. Just strip the speaker insulation at the wire end, then insert the bare wire into the hole of the spring-loaded push terminal. At the same time, the concealed mount gasket system creates a clean, finished appearance for any vehicle. General Features: 10" 4 ohm S-Series (Type-S) Subwoofer RMS Power Handling: 600 watts Peak Power Handling: 1800 watts  Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 4-11/16" Cutout diameter: 8-13/16 Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 33 Hz Authorized Dealer 1-year Manufacturer's Warranty What's in the S-W10D4 package: S-W10D4 owner's manual One 10" Dual 4-ohm voice coil subwoofer Two 3" jumper cables Subwoofer Application Guide Online product registration information Warranty information ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

2 Alpine S-W10D2 1800W Max (600W RMS) 10" S-Series Dual 2 Ohm Car Subwoofer Alpine introduces the all-new S-Series Subwoofers; their unique design substantially improves bass output and provides installation versatility. Each S-Series subwoofer uses a custom-stamped steel frame and is available in twelve, ten, and eight-inch. These high-strength frames were designed to withstand the rigors of the improved S-Series motor. They have frame leg vents, a vented back plate to help cool the subwoofer voice coil and motor parts, and a shallow design to help fit in smaller spaces. The S-Series Subwoofers incorporates two strontium ferrite magnets stacked together, providing increased motor strength and excursion, ultimately delivering an accurate bass to your music. The convenient push-type insert terminals with a dual voice coil jumper system will significantly reduce installation time. Just strip the speaker insulation at the wire end, then insert the bare wire into the hole of the spring-loaded push terminal. At the same time, the concealed mount gasket system creates a clean, finished appearance for any vehicle. General Features: 10" 2 ohm S-Series (Type-S) Subwoofer RMS Power Handling: 600 watts Peak Power Handling: 1800 watts  Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 4-11/16" Cutout diameter: 8-13/16 Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 33 Hz Authorized Dealer 1-year Manufacturer's Warranty What is in the S-W10D2 package: S-W10D2 owner's manual One 10" Dual 2-ohm voice coil subwoofer 1 Rubber concealing ring Two 3" jumper cables (each has a single banana connector on each end) Subwoofer Application Guide Online product registration information Warranty Information ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine SWT-10S2 1000W Peak 10" SWT Series Single 2-ohm Shallow Mount Subwoofer Right size, Right sound. Here's a big bass breakthrough for truck lovers. Alpine engineered their SWT-10S2 10" subwoofer to go behind your seat and sound especially good in the limited space of a truck cab. This deep-sounding, high-performance sub works well in shallow enclosures that'll fit behind or under the seat in your truck. A "high amplitude" surround allows more cone travel than a regular sub, so the SWT-10S2 can push more air and play louder. Airflow-insured subs get hot as they play, and the heat usually gets vented away via a port in the back of the sub's pole piece. Alpine recessed the pole port and added cooling air vents on the sides of the frame, allowing you to use an enclosure with an inside clearance of as little as 4-3/16" without blocking critical airflow. General Features: 10" SWT Series Single 2-ohm Shallow Mount Truck Subwoofer Peak Power Handling: 1,000 watts RMS Power Handling: 350 watts Recommended Power Range: 100W - 350W Poly-Mica Dust Cap & Pulp-Kevlar Polyurethane Foam Surround H.A.M.R. Surround Technology Spiral Cut Aluminum Former 65mm Voice Coil with High-Temp 4-Layer SVC Winding 8AWG Push Terminals Top-mount depth: 4-3/16" Mounting Diameter: 8-15/16'' Frequency Response: 30 - 200 Hz Sensitivity: 84.8 dB Authorized Dealer 1-year Manufacturer's Warranty What is in the SWT-10S2 package: SWT-10S2 owner's manual 10" Thin-mount subwoofer Online product registration information Warranty information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Punch P3D4-10 P3 Series DVC 4-Ohm 10-Inch 500-Watt RMS 1000 Watts Peak Subwoofer The Rockford Fosgate P3D4-10 is the best-performing Punch series subwoofer. The P3 subwoofers now feature anodized aluminum cones and dust caps along with unique spider venting to keep the motor cooler than previous versions. These subs feature VAST technology to increase surface cone area to 25% and a Flex Fit basket for extreme installations. A new hybrid stamp-cast basket offers the best of both worlds by providing super strength while minimizing weight and resonance. 10" Punch P3 Series Dual 4 Ohm Subwoofer General Feature: 10" Punch P3 Series Dual 4 Ohm Subwoofer Power Handling: Peak: 1,000 watts Power Handling: RMS: 500 watts Impedance: 4 ohm Anodized aluminum heat sinking cone & dust cap for strength and durability Tall profile true Santoprene vertical attach surround technique increases a speaker's effective radiating cone area Dual tear & fatigue resistant linear poly cotton spiders Optimized motor magnetics with extended pole and bumped backplate Fatigue-resistant and reduced-strain stitched tinsel leads Multipoint high temp/strength neck joint bonding technique Sturdy 16-gauge compound bend frame geometry Semi-Flexible PVC removable protective motor cover Custom insulated compression input terminal assembly Proprietary spider venting/cooling technique Decorative die-cast trim ring Custom 10-AWG nickel-plated push terminals High-temperature 4-layer 2-1/2" voice coil with spun-laced Nomex insulating reinforcement collar Double-stacked ferrite magnet structure Frequency response: 28-250 Hz Sensitivity: 82 dB Xmax: 13.9 mm Mounting Depth: 6-1/4" Cutout Diameter: 9-1/8" Magnet Weight: 81 oz Frequency Response: 28 - 250 Hz Xmax: 15.9mm Sensitivity: 82 dB @ 1 watt / 1 meter Recommended Ported Enclosure: 1.40ft³ Recommended Sealed Enclosure: 0.59ft³ Magnet Weight: 81 oz Frequency Response: 28 - 250 Hz Xmax: 15.9mm Sensitivity: 82 dB @ 1 watt / 1 meter Recommended Ported Enclosure: 1.40ft³ Recommended Sealed Enclosure: 0.59ft³ Matching Amplifiers: (one subwoofer) Rockford Fosgate R750-1D, Parallel @2ohms Rockford Fosgate P1000X1bd, Parallel @2ohms Rockford Fosgate R500X1D, Parallel @2ohms Matching Amplifier: (two subwoofers) Rockford Fosgate P1000X1bd, Parallel @1ohm Rockford Fosgate R1200-1D, Parallel @1ohm Authorized Internet Dealer 1-year Manufacturer's Warranty ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca