00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate Punch P1000X5
1000W RMS Punch Series 5-Channel Stereo Full-Range Class BD Car Amplifier w/ Dedicated Sub Channel $629.99 $849.99
1000W RMS Punch Series 5-Channel Stereo Full-Range Class BD Car Amplifier w/ Dedicated Sub Channel $629.99 $849.99
Rockford Fosgate Punch P1000X5 5-channel car amplifier — 75 watts RMS x 4 at 4 ohms + 500 watts RMS x 1 at 1 ohm
The Punch P1000X5 is an ultra-efficient 5-channel amplifier capable of running your entire system without excessive drain on your charging system. The P1000X5 is perfect for running a front/rear system and a dedicated subwoofer. The P1000X5 1,000 Watt full-range 5-channel is the one-and-only amplifier you will need to run your entire system. Run dash speakers off the front channels, run back speakers off the rear channels, and run subwoofer(s) off the 5th channel! Known worldwide for brute power, this amplifier offers a higher level of efficiency along with tri-stage protection that covers thermal, over-current, and short circuits.
General Features:
5-channel car amplifier
75 watts RMS x 4 + 150 watts RMS x 1 at 4 ohms
125 watts RMS x 4 + 300 watts RMS x 1 at 2 ohms
250 watts RMS x 2 bridged at 4 ohms + 500 watts RMS at 1 ohm
CEA-2006 compliant
variable high- and low-pass filters (50-250 Hz, 12 dB/octave)
variable PEQ2 bass/treble boost (0-18 dB at 45 Hz and 0-14 dB at 12.5K Hz)
switchable subsonic filter (28 Hz, 12 dB/octave) on subwoofer channel
L.E.A.N. gain setup system includes test tone CD
test tones are also available as MP3 download from Amazon on Demand, Rhapsody, Google Play, and Spotify, labeled "3sixty.3 setup disc" (Punch amps and the 3sixty.3 use the same test tone tracks for setup)
Class-BD amplifier design
frequency response: 20-20K Hz
Dynamic Thermal Management and MEHSA MOSFET cooling systems
MOSFET power and output stages
preamp and speaker-level inputs (speaker-level inputs require a speaker wire to RCA adapter)
signal-sensing turn-on with speaker-level inputs eliminate the need for remote turn-on lead
optional PLC2 wired remote level control with clip light available
4-gauge power and ground leads and a 150-amp fuse recommended — wiring and hardware not included with amplifier
no onboard fuses — when installing multiple amps in a system, an additional 150-amp in-line fuse between the distribution block and the amplifier is recommended.
15-1/8"W x 2-7/16"H x 8-13/16"D
What is in the box:
5-Channel amplifier
Four 1-1/2" Self-tapping screws
5mm Allen wrench
Quick setup instructions
Certificate of Performance
Setup/Manual disc
Rockford Fosgate Punch P1000X5 owner's manual
⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov
00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate Punch 1000 Watt 5-Channel Car Amplifier - P1000X5
$629.99
$849.99
Rockford Fosgate Punch P1000X5 5-channel car amplifier — 75 watts RMS x 4 at 4 ohms + 500 watts RMS x 1 at 1 ohm
The Punch P1000X5 is an ultra-efficient 5-channel amplifier capable of running your entire system without excessive drain on your charging system. The P1000X5 is perfect for running a front/rear system and a dedicated subwoofer. The P1000X5 1,000 Watt full-range 5-channel is the one-and-only amplifier you will need to run your entire system. Run dash speakers off the front channels, run back speakers off the rear channels, and run subwoofer(s) off the 5th channel! Known worldwide for brute power, this amplifier offers a higher level of efficiency along with tri-stage protection that covers thermal, over-current, and short circuits.
General Features:
5-channel car amplifier
75 watts RMS x 4 + 150 watts RMS x 1 at 4 ohms
125 watts RMS x 4 + 300 watts RMS x 1 at 2 ohms
250 watts RMS x 2 bridged at 4 ohms + 500 watts RMS at 1 ohm
CEA-2006 compliant
variable high- and low-pass filters (50-250 Hz, 12 dB/octave)
variable PEQ2 bass/treble boost (0-18 dB at 45 Hz and 0-14 dB at 12.5K Hz)
switchable subsonic filter (28 Hz, 12 dB/octave) on subwoofer channel
L.E.A.N. gain setup system includes test tone CD
test tones are also available as MP3 download from Amazon on Demand, Rhapsody, Google Play, and Spotify, labeled "3sixty.3 setup disc" (Punch amps and the 3sixty.3 use the same test tone tracks for setup)
Class-BD amplifier design
frequency response: 20-20K Hz
Dynamic Thermal Management and MEHSA MOSFET cooling systems
MOSFET power and output stages
preamp and speaker-level inputs (speaker-level inputs require a speaker wire to RCA adapter)
signal-sensing turn-on with speaker-level inputs eliminate the need for remote turn-on lead
optional PLC2 wired remote level control with clip light available
4-gauge power and ground leads and a 150-amp fuse recommended — wiring and hardware not included with amplifier
no onboard fuses — when installing multiple amps in a system, an additional 150-amp in-line fuse between the distribution block and the amplifier is recommended.
15-1/8"W x 2-7/16"H x 8-13/16"D
What is in the box:
5-Channel amplifier
Four 1-1/2" Self-tapping screws
5mm Allen wrench
Quick setup instructions
Certificate of Performance
Setup/Manual disc
Rockford Fosgate Punch P1000X5 owner's manual
⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov
00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate R2-750X1 750-Watt Mono Amplifier
$349.99
$429.99
Rockford Fosgate Prime R2-750X1 750W Prime Series Monoblock Subwoofer Class D Amplifier
Primed for performance, the R2-750X1 amplifier is a 750-watt, Class-D, capable of operating at 4Ω, 2Ω, or 1Ω mono. This amplifier is extremely efficient because of its Class-D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allow you to tune the bass for the desired level of the music.
Rockford Fosgate's R2 amplifiers are the building blocks for great audio systems, powerful enough to even DRIVE our Punch speakers and subwoofers. They have undergone an amazing upgrade by packing them with the latest features at an incredible value. Best of all, they are designed and engineered here in Tempe, Arizona.
General Features:
Rockford Fosgate Prime R2-750X1
RMS Power Rating: 4 ohms: 250 watts x 1 channel
RMS Power Rating: 2 ohms: 500 watts x 1 channel
RMS Power Rating: 1 ohm: 750 watts x 1 channel
Total power output: 500 watts
Balanced Differential Inputs with RCA Pass Through Outputs
High-Level Input Capable
Defeatable Auto Turn on Circuit
Features C.L.E.A.N. Set-up
Variable Input Gain adjustment level
R.L.C. Remote Level Control
Variable Infrasonic Filter
Continuously Variable On-Board Punch EQ
Top Mounted Control Panel
Short Circuit & Over Current Protection
CEA-2006 Compliant & CE Compliant
Full Range Class D
Rollback Protection
Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers
Input sensitivity: Low-Level: 150 mV - 4 V
Input sensitivity: High-Level: 450 mV - 12 V
Frequency Response: 20 Hz - 250 Hz
Total Harmonic Distortion (THD): >1%
Crossover Controls: Low-Pass: 50 Hz - 250 Hz
Crossover Controls: Sub Infrasonic: 15 Hz - 40 Hz
Recommended Fuse Rating: 120A
4-gauge power and ground wiring are recommended for installation.
Dimensions: "1.9" x "6.8" x "10.1"
Authorized Internet Dealer
1-Year Manufacturer's Warranty
What is in the R2-750X1 package:
Mono subwoofer amplifier
Wired Remote Level Control module
16' Remote cable (RJ-25 connector on both ends)
One 7" Speaker input harness
3mm Allen Hex key
Four 3/4" Screws
Two 1/2" Screws
5 Flat washers
1 Nut
Installation and Operation Instructions
Certificate of Performance
Rockford Fosgate contact information
Rockford Fosgate R2-500X1 owner's manual
⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.
00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate R2-750X1 Prime 750 Watt 1ohm Mono punch Amplifier Class D
$349.99
$429.99
Rockford Fosgate Prime R2-750X1 750W Prime Series Monoblock Subwoofer Class D Amplifier
Primed for performance, the R2-750X1 amplifier is a 750-watt, Class-D, capable of operating at 4Ω, 2Ω, or 1Ω mono. This amplifier is extremely efficient because of its Class-D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allow you to tune the bass for the desired level of the music.
Rockford Fosgate's R2 amplifiers are the building blocks for great audio systems, powerful enough to even DRIVE our Punch speakers and subwoofers. They have undergone an amazing upgrade by packing them with the latest features at an incredible value. Best of all, they are designed and engineered here in Tempe, Arizona.
General Features:
Rockford Fosgate Prime R2-750X1
RMS Power Rating: 4 ohms: 250 watts x 1 channel
RMS Power Rating: 2 ohms: 500 watts x 1 channel
RMS Power Rating: 1 ohm: 750 watts x 1 channel
Total power output: 500 watts
Balanced Differential Inputs with RCA Pass Through Outputs
High-Level Input Capable
Defeatable Auto Turn on Circuit
Features C.L.E.A.N. Set-up
Variable Input Gain adjustment level
R.L.C. Remote Level Control
Variable Infrasonic Filter
Continuously Variable On-Board Punch EQ
Top Mounted Control Panel
Short Circuit & Over Current Protection
CEA-2006 Compliant & CE Compliant
Full Range Class D
Rollback Protection
Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers
Input sensitivity: Low-Level: 150 mV - 4 V
Input sensitivity: High-Level: 450 mV - 12 V
Frequency Response: 20 Hz - 250 Hz
Total Harmonic Distortion (THD): >1%
Crossover Controls: Low-Pass: 50 Hz - 250 Hz
Crossover Controls: Sub Infrasonic: 15 Hz - 40 Hz
Recommended Fuse Rating: 120A
4-gauge power and ground wiring are recommended for installation.
Dimensions: "1.9" x "6.8" x "10.1"
Authorized Internet Dealer
1-Year Manufacturer's Warranty
What is in the R2-750X1 package:
Mono subwoofer amplifier
Wired Remote Level Control module
16' Remote cable (RJ-25 connector on both ends)
One 7" Speaker input harness
3mm Allen Hex key
Four 3/4" Screws
Two 1/2" Screws
5 Flat washers
1 Nut
Installation and Operation Instructions
Certificate of Performance
Rockford Fosgate contact information
Rockford Fosgate R2-500X1 owner's manual
⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.
00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate Prime R2-500X1 Amplifier
500W Prime Series Monoblock Subwoofer Class D Amplifier $249.99 $350.00
500W Prime Series Monoblock Subwoofer Class D Amplifier $249.99 $350.00
Rockford Fosgate Prime R2-500X1 500W Prime Series Monoblock Subwoofer Class D Amplifier
Primed for performance, the R2-500X1 amplifier is a 500 watt, class-D, capable of operating at 4Ω or 2Ω mono. This amplifier is extremely efficient because of its class D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allows you to tune the bass for the desired level for the music.
General Features:
Rockford Fosgate Prime R2-500X1
RMS Power Rating:
4 ohms: 300 watts x 1 chan.
2 ohms: 500 watts x 1 chan.
Total power output: 500 watts
Balanced Differential Inputs with RCA Pass Through Outputs
High-Level Input Capable
Defeat able Auto Turn-On Circuit
Features C.L.E.A.N. Set-up
Variable Input Gain adjustment level
R.L.C. Remote Level Control
Variable Infrasonic Filter
Continuously Variable On Board Punch EQ
Top Mounted Control Panel
Short Circuit & Over Current Protection
CEA-2006 Compliant & CE Compliant
Full Range Class D
Rollback Protection
Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers
Input sensitivity:
Low-Level: 150 mV - 4 V
High-Level: 450 mV - 12 V
Frequency Response: 20 Hz - 250 Hz
Total Harmonic Distortion (THD): >1%
Crossover Controls
Low-Pass: 50 Hz - 250 Hz
Sub Infrasonic: 15 Hz - 40 Hz
Recommended Fuse Rating: 80A
4 gauge power and ground wiring is recommended for installation
Dimensions: "1.9" x "6.8" x "8.5"
Authorized Internet Dealer
1 Year Manufacturer's Warranty
What is in the R2-500X1 package:
Rockford Fosgate R2-500X1 owner's manual
Mono subwoofer amplifier
Wired Remote Level Control module
16' Remote cable (RJ-25 connector on both ends)
One 7" Speaker input harnesses
3mm Allen Hex key
Four 3/4" Screws
Two 1/2" Screws
5 Flat washers
1 Nut
Installation and Operation Instructions
Certificate of Performance
Rockford Fosgate contact information
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca
00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate R2-500X1 Prime 500 Watt 1ohh Mono punch Amplifier Class D | NEW
$249.99
$350.00
Rockford Fosgate Prime R2-500X1 500W Prime Series Monoblock Subwoofer Class D Amplifier
Primed for performance, the R2-500X1 amplifier is a 500 watt, class-D, capable of operating at 4Ω or 2Ω mono. This amplifier is extremely efficient because of its class D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allows you to tune the bass for the desired level for the music.
General Features:
Rockford Fosgate Prime R2-500X1
RMS Power Rating:
4 ohms: 300 watts x 1 chan.
2 ohms: 500 watts x 1 chan.
Total power output: 500 watts
Balanced Differential Inputs with RCA Pass Through Outputs
High-Level Input Capable
Defeat able Auto Turn-On Circuit
Features C.L.E.A.N. Set-up
Variable Input Gain adjustment level
R.L.C. Remote Level Control
Variable Infrasonic Filter
Continuously Variable On Board Punch EQ
Top Mounted Control Panel
Short Circuit & Over Current Protection
CEA-2006 Compliant & CE Compliant
Full Range Class D
Rollback Protection
Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers
Input sensitivity:
Low-Level: 150 mV - 4 V
High-Level: 450 mV - 12 V
Frequency Response: 20 Hz - 250 Hz
Total Harmonic Distortion (THD): >1%
Crossover Controls
Low-Pass: 50 Hz - 250 Hz
Sub Infrasonic: 15 Hz - 40 Hz
Recommended Fuse Rating: 80A
4 gauge power and ground wiring is recommended for installation
Dimensions: "1.9" x "6.8" x "8.5"
Authorized Internet Dealer
1 Year Manufacturer's Warranty
What is in the R2-500X1 package:
Rockford Fosgate R2-500X1 owner's manual
Mono subwoofer amplifier
Wired Remote Level Control module
16' Remote cable (RJ-25 connector on both ends)
One 7" Speaker input harnesses
3mm Allen Hex key
Four 3/4" Screws
Two 1/2" Screws
5 Flat washers
1 Nut
Installation and Operation Instructions
Certificate of Performance
Rockford Fosgate contact information
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca
00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate Prime 500W 4-Channel Full Range Class D Amplifier R2-500X4
$329.99
$399.99
Rockford Fosgate Prime R2-500X4 500W Prime Series 4-Channel Full Range Class D Amplifier
Primed for performance, the R2-500X4 is a 500-watt, full-range Class-D amplifier capable of operating at 4Ω or 2Ω stereo and 4Ω bridged/mono. This amplifier is extremely efficient because of its Class-D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. supply that generates more power as voltage increases. Rockford Fosgate's R2 amplifiers are the building blocks for great audio systems, powerful enough to even DRIVE our Punch speakers and subwoofers. They have undergone an amazing upgrade by packing them with the latest features at an incredible value. Best of all, they are designed and engineered here in Tempe, Arizona.
General Features:
Rockford Fosgate Prime R2-500X4
RMS Power Rating: 4 ohms: 75 watts x 4 Channel
RMS Power Rating: 2 ohms: 125 watts x 4 Channel
Bridged, 4 ohms: 250 watts x 2 Channel
Total power output: 500 watts
Balanced Differential Inputs with RCA Pass Through Outputs
High-Level Input Capable
Defeatable Auto Turn on Circuit
Features C.L.E.A.N. Set-up
2/4 Channel Input Selection Switch
Front and Rear Variable Input Gain adjustment level
Continuously Variable On-Board Punch EQ
Top Mounted Control Panel
Short Circuit & Over Current Protection
CEA-2006 Compliant & CE Compliant
Rollback Protection
Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers
Frequency Response: 20 Hz - 20 kHz
Total Harmonic Distortion (THD): >1%
Signal to Noise Ratio: xx dB
Variable high-pass filter: 50 - 250 Hz, 24 dB/octave
Variable low-pass filter: 50 - 250Hz, 24 dB/octave
Recommended Fuse Rating: 80A
4-gauge power and ground wiring are recommended for installation
Dimensions: 1.9" x "6.8" x "10.1"
Authorized Internet Dealer
1-year Manufacturer's Warranty
What is in the R2-500X4 package:
R2-500X4 owner's manual
4-Channel amplifier
Two 7" Speaker input harnesses
3mm Allen Hex key
Four 3/4" Screws
4 Flat washers
Installation and Operation Instructions
Certificate of Performance
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca
00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate R2-500X4 Prime 500W 4-Channel Full Range Class D Amplifier
$329.99
$399.99
Rockford Fosgate Prime R2-500X4 500W Prime Series 4-Channel Full Range Class D Amplifier
Primed for performance, the R2-500X4 is a 500-watt, full-range Class-D amplifier capable of operating at 4Ω or 2Ω stereo and 4Ω bridged/mono. This amplifier is extremely efficient because of its Class-D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. supply that generates more power as voltage increases. Rockford Fosgate's R2 amplifiers are the building blocks for great audio systems, powerful enough to even DRIVE our Punch speakers and subwoofers. They have undergone an amazing upgrade by packing them with the latest features at an incredible value. Best of all, they are designed and engineered here in Tempe, Arizona.
General Features:
Rockford Fosgate Prime R2-500X4
RMS Power Rating: 4 ohms: 75 watts x 4 Channel
RMS Power Rating: 2 ohms: 125 watts x 4 Channel
Bridged, 4 ohms: 250 watts x 2 Channel
Total power output: 500 watts
Balanced Differential Inputs with RCA Pass Through Outputs
High-Level Input Capable
Defeatable Auto Turn on Circuit
Features C.L.E.A.N. Set-up
2/4 Channel Input Selection Switch
Front and Rear Variable Input Gain adjustment level
Continuously Variable On-Board Punch EQ
Top Mounted Control Panel
Short Circuit & Over Current Protection
CEA-2006 Compliant & CE Compliant
Rollback Protection
Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers
Frequency Response: 20 Hz - 20 kHz
Total Harmonic Distortion (THD): >1%
Signal to Noise Ratio: xx dB
Variable high-pass filter: 50 - 250 Hz, 24 dB/octave
Variable low-pass filter: 50 - 250Hz, 24 dB/octave
Recommended Fuse Rating: 80A
4-gauge power and ground wiring are recommended for installation
Dimensions: 1.9" x "6.8" x "10.1"
Authorized Internet Dealer
1-year Manufacturer's Warranty
What is in the R2-500X4 package:
R2-500X4 owner's manual
4-Channel amplifier
Two 7" Speaker input harnesses
3mm Allen Hex key
Four 3/4" Screws
4 Flat washers
Installation and Operation Instructions
Certificate of Performance
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca
00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate Punch P500X1bd Mono subwoofer amplifier 500 watts RMS x 1 at 1 ohm
$389.99
$499.99
Rockford Fosgate Punch P500X1bd Mono subwoofer amplifier 500 watts RMS x 1 at 1 ohm
Big power for your sub or subsystem
Rockford Fosgate's Punch P500X1bd subwoofer amp can produce up to 500 watts RMS, giving you plenty of clean power for your rhythm track. And the P500X1bd can drive a 1-ohm load, so you can power multiple subs without any trouble. A low-pass filter keeps the high notes away from your sub, while a subsonic filter helps you rein in runaway boom. The Punch bass boost lets you add some of that boom back into the mix when it's needed.
Easy to set for optimum performance
Once again, Rockford Fosgate steps away from the crowd with their C.L.E.A.N. technology (Calibrated Level Eliminates Audible Noise) — a setup system that ensures your music will sound as clean and powerful as possible. It works like this: first, download the setup tones from Rockford Fosgate, then play the tone, adjust the receiver volume until a red clip light on the amp goes out, then turn the amp gain up until a blue light comes on. It's that simple — your amplifier will be perfectly set to match your receiver's output. When your receiver reaches maximum clean volume, you'll get maximum clean power from your power amp. At quiet listening levels, you'll hear less background noise and more of your music.
Keeps an eye on things while playingIf that blue light turns solid red while you're playing music, the amp's telling you that your source is distorting and you should turn it down, or risk damage to your gear. The optional PLC2 remote level control also doubles as a clip indicator, so you can see from the front seat if your music's clipping. The amp's built-in computer keeps tabs on the output current, ensuring that plunging speaker impedances (they change during play) or even a short circuit won't hurt anything.
Maintaining coolness raises efficiency and lowers distortionRockford Fosgate's Dynamic Thermal Management system uses forced air to dissipate heat evenly across the amp and out through the high-mass heatsink, efficiently drawing heat away from vital internal parts. Their proprietary MEHSA cooling process maximizes the heat transfer from the MOSFET devices to the heatsink, allowing the heat to escape more readily, so the transistors stay cooler and work better.
Product highlights:
mono subwoofer amplifier
150 watts RMS x 1 at 4 ohms (300 watts RMS x 1 at 2 ohms)
500 watts RMS x 1 at 1 ohm
CEA-2006 compliant
Features:
variable low-pass filter filter (50-250 Hz, 12 dB/octave)
selectable subsonic filter (28Hz, 12 dB/octave)
variable PEQ2 bass boost (0-18 dB at 45 Hz)
C.L.E.A.N. gain setup system includes clip lights and link to Rockford Fosgate's setup tones
Class-BD amplifier design
frequency response: 20-250 Hz
Dynamic Thermal Management and MEHSA MOSFET cooling systems
MOSFET power and output stages
preamp inputs and outputs
speaker-level inputs (speaker wire to RCA adapter required)
signal-sensing turn-on with speaker-level inputs eliminate the need for remote turn-on lead
More Info:
optional PLC2 wired remote level control with clip light available
4-gauge power and ground leads and an 80-amp fuse recommended — wiring and hardware not included with amplifier
no onboard fuses — when installing multiple amps in a system, an additional 80-amp in-line fuse between the distribution block and the amplifier is recommended
11-1/8"W x 2-7/16"H x 8-13/16"D
warranty: 1 year
What is in the P500X1bd box:
Mono subwoofer amplifier
Four 1-1/2" Self-tapping screws
2.5mm Allen wrench
Quick setup instructions
Certificate of Performance
P500X1bd owner's manual
⚠️Warning:
Cancer and Reproductive Harm-www.P65Warnings.ca.gov
00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate - P500X1bd - Class D Amplifiers
$389.99
$719.99
Rockford Fosgate Punch P500X1BD 500W RMS Punch Series Monoblock Class D Car Power Amplifier
The Punch P500X1bd is a mono amplifier capable of 500 Watts into a 1-Ohm load. The Class-BD technology produces bass more efficiently over traditional amps, and its frequency response allows it to be optimized for subwoofers.
General Features
Punch BD Series Monoblock Class BD Car Amplifier
RMS Power Rating:
4 ohms: 150 watts x 1 chan.
2 ohms: 300 watts x 1 chan.
1 ohm: 500 watts x 1 chan.
CEA-2006 compliant amplifier
MOSFET power supply
Muted turn-on.
Cast aluminum heatsink.
12dB/octave Butterworth crossover
Stealth top-mounted control panel
LED power, thermal, and protect indicators.
Nickel-plated captive C-clamp terminals.
Ultra-efficient Class BD circuitry to maximize amplifier power efficiency.
On-board differential inputs eliminate noise picked up by the signal cable.
Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator)
High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately)
MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span.
Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances.
Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low.
DSM (Discrete Surface Mounted Components) utilize 1% tight-tolerances improving the efficiency of the circuit and lowers the operating temperature and potential for noise-like circuit boards designed by aerospace manufacturers.
Input sensitivity: 150mV - 12V
On-board Punch EQ with +18dB boost @ 45Hz.
Variable low-pass filter: 50-250 Hz
Selectable infrasonic filter: off / 28 Hz
Frequency response: 20 - 250 Hz
Total Harmonic Distortion: <1.0%
Dimensions: 11"L x 7-3/4"W x 2-3/8"H
8 AWG to 18 AWG speaker wire output terminals
Authorized Internet Dealer
1-year Manufacturer's Warranty
What is in the P500X1bd box:
Mono subwoofer amplifier
Four 1-1/2" Self-tapping screws
2.5mm Allen wrench
Quick setup instructions
Certificate of Performance
P500X1bd owner's manual
⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca
00
DAYS 00
HRS 00
MIN 00
SEC
DAYS 00
HRS 00
MIN 00
SEC
Rockford Fosgate Prime R1200-1D
1200W RMS Prime Series Class-D Monoblock 1-Ohm Stable Amplifier $409.99 $679.99
1200W RMS Prime Series Class-D Monoblock 1-Ohm Stable Amplifier $409.99 $679.99
Rockford Fosgate Prime R1200-1D 1200W RMS Prime Series Class-D Monoblock 1-Ohm Stable Amplifier
The PRIME R1200-1D is an ultra-efficient mono amplifier for cars and trucks that can produce 1,200 Watts into a 1-Ohm load without taxing the electrical system. The frequency response of the R1200-1D is optimized exclusively for use with subwoofers. The Prime R1200-1D subwoofer amplifier offers high efficiency through the implementation of its Class-D circuitry while delivering rich, full bass to any system. This car amplifier is optimized for subwoofers with the implementation of an infrasonic filter to keep those ultra-low (inaudible) bass notes from damaging your subwoofer system. Match with a 4-channel stereo amplifier for your mids/highs and you'll have a Rockford Fosgate system that any Car Audio Fanatic will envy.
General Features:
Rockford Fosgate Prime Series R1200-1D
Class-D 1-Ohm Stable Monoblock Amplifier
RMS Power Rating: 4 ohms: 400 watts x 1 channel
RMS Power Rating: 2 ohms: 800 watts x 1 channel
RMS Power Rating: 1 ohm: 1200 watts x 1 channel
CEA-2006 Compliant Amplifier
Pulse Width Modulated MOSFET power supply
Wired remote bass level control included
LED power (green) and protect (red) indicators
Soft start turn-on
Nickel-plated RCA level inputs
Nickel-plated screw terminals
Preamp RCA outputs to daisy chain multiple amps
3-way protection circuitry (thermal, overload, and speaker short protection)
Heavy-duty aluminum alloy heat-sink for extreme heat dissipation
Input sensitivity: 150mV - 4V
Frequency Response: 20 - 250Hz
Total Harmonic Distortion (THD): <1.0%
Signal to Noise Ratio: 100dB
Variable low-pass filter: 50 - 250 Hz, 12 dB/octave
Subsonic (infrasonic) filter: 15 - 40 Hz , 12 dB/octave
Variable Bass Boost: 0 to +18 dB bass boost at 45 Hz
Fuse Rating: 150A x 1 (recommended, not included)
12 AWG speaker wire gauge outputs
4 gauge power and ground wiring is recommended for installation
Weight: 7.825 lbs
Dimensions: 11.06"W x 6.77"L x 1.97"H
Also Found As Prime 1200 Watt, R12001D, R1200, R12001
Authorized Internet Dealer
1-year Manufacturer's Warranty
⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca