Rockford Fosgate Amplifiers (82)

Rockford Fosgate Punch P1000X5 5-channel car amplifier — 75 watts RMS x 4 at 4 ohms + 500 watts RMS x 1 at 1 ohm The Punch P1000X5 is an ultra-efficient 5-channel amplifier capable of running your entire system without excessive drain on your charging system. The P1000X5 is perfect for running a front/rear system and a dedicated subwoofer. The P1000X5 1,000 Watt full-range 5-channel is the one-and-only amplifier you will need to run your entire system. Run dash speakers off the front channels, run back speakers off the rear channels, and run subwoofer(s) off the 5th channel! Known worldwide for brute power, this amplifier offers higher efficiency along with tri-stage protection that covers thermal, over-current, and short circuits. General Features: 5-channel car amplifier 75 watts RMS x 4 + 150 watts RMS x 1 at 4 ohms 125 watts RMS x 4 + 300 watts RMS x 1 at 2 ohms 250 watts RMS x 2 bridged at 4 ohms + 500 watts RMS at 1 ohm CEA-2006 compliant variable high- and low-pass filters (50-250 Hz, 12 dB/octave) variable PEQ2 bass/treble boost (0-18 dB at 45 Hz and 0-14 dB at 12.5K Hz) switchable subsonic filter (28 Hz, 12 dB/octave) on subwoofer channel L.E.A.N. gain setup system includes test tone CD Test tones are also available as MP3 downloads from Amazon on Demand, Rhapsody, Google Play, and Spotify, labeled "3sixty..3 setup disc" (Punch amps and the 3sixty..3 use the same test tone tracks for setup) Class-BD amplifier design frequency response: 20-20K Hz Dynamic Thermal Management and MEHSA MOSFET cooling systems MOSFET power and output stages preamp and speaker-level inputs (speaker-level inputs require a speaker wire to RCA adapter) signal-sensing turn-on with speaker-level inputs eliminates the need for a remote turn-on lead optional PLC2 wired remote level control with clip light available 4-gauge power and ground leads and a 150-amp fuse recommended — wiring and hardware not included with amplifier No onboard fuses — when installing multiple amps in a system, an additional 150-amp in-line fuse between the distribution block and the amplifier is recommended. 15-1/8"W x 2-7/16"H x 8-13/16"D What is in the box: 5-Channel amplifier Four 1-1/2" Self-tapping screws 5mm Allen wrench Quick setup instructions Certificate of Performance Setup/Manual disc Rockford Fosgate Punch P1000X5 owner's manual Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Punch P1000X5 5-channel car amplifier — 75 watts RMS x 4 at 4 ohms + 500 watts RMS x 1 at 1 ohm The Punch P1000X5 is an ultra-efficient 5-channel amplifier capable of running your entire system without excessive drain on your charging system. The P1000X5 is perfect for running a front/rear system and a dedicated subwoofer. The P1000X5 1,000 Watt full-range 5-channel is the one-and-only amplifier you will need to run your entire system. Run the dash speakers off the front channels, the back speakers off the rear channels, and the subwoofer(s) off the 5th channel! Known worldwide for brute power, this amplifier offers higher efficiency along with tri-stage protection that covers thermal, over-current, and short circuits. General Features: 5-channel car amplifier 75 watts RMS x 4 + 150 watts RMS x 1 at 4 ohms 125 watts RMS x 4 + 300 watts RMS x 1 at 2 ohms 250 watts RMS x 2 bridged at 4 ohms + 500 watts RMS at 1 ohm CEA-2006 compliant variable high- and low-pass filters (50-250 Hz, 12 dB/octave) variable PEQ2 bass/treble boost (0-18 dB at 45 Hz and 0-14 dB at 12.5K Hz) switchable subsonic filter (28 Hz, 12 dB/octave) on subwoofer channel L.E.A.N. gain setup system includes a test tone CD Test tones are also available as MP3 downloads from Amazon on Demand, Rhapsody, Google Play, and Spotify, labeled "3sixty..3 setup disc" (Punch amps and the 3sixty..3 use the same test tone tracks for setup) Class-BD amplifier design frequency response: 20-20K Hz Dynamic Thermal Management and MEHSA MOSFET cooling systems MOSFET power and output stages preamp and speaker-level inputs (speaker-level inputs require a speaker wire to RCA adapter) signal-sensing turn-on with speaker-level inputs eliminates the need for a remote turn-on lead optional PLC2 wired remote level control with clip light available 4-gauge power and ground leads and a 150-amp fuse recommended — wiring and hardware not included with amplifier No onboard fuses — when installing multiple amps in a system, an additional 150-amp in-line fuse between the distribution block and the amplifier is recommended. 15-1/8"W x 2-7/16"H x 8-13/16"D What is in the box: 5-Channel amplifier Four 1-1/2" Self-tapping screws 5mm Allen wrench Quick setup instructions Certificate of Performance Setup/Manual disc Rockford Fosgate Punch P1000X5 owner's manual Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Punch P300X2 300W RMS Punch Series 2-Channel Stereo Class AB Car Power Amplifier The Punch P300X2 is a 2-channel stereo amplifier capable of producing 150 Watts into each channel at 2-ohms. It is great for driving a pair of coaxial speakers, component speakers, or a single subwoofer. The amplifier can also be run simultaneously in stereo/mono mode when using passive crossovers (not supplied) on all speakers. With proven PUNCH technology, the P300X2 delivers real Rockford Fosgate power from a small design and is flexible enough to accommodate any moderately sized system. General Features: Punch Series 2-Channel Class AB Car Amplifier RMS Power Rating: 4 ohms: 100 watts x 2 Channel 2 ohms: 150 watts x 2 Channel Bridged, 4 ohms: 300 watts x 1 chan. CEA-2006 compliant amplifier Features C.L.E.A.N. Set-up with input/output clip detection and indicator LEDs MOSFET power supply Muted turn on Cast aluminum heatsink 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protection indicators Nickel-plated captive C-clamp terminals Ultra-efficient Class BD circuitry to maximize amplifier power efficiency On-board differential inputs eliminate noise picked up by the signal cable Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately) MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low DSM (Discrete Surface Mounted Components) utilizes 1% tight-tolerances, improving the efficiency of the circuit and lowering the operating temperature and potential for noise, similar to circuit boards designed by aerospace manufacturers Input sensitivity: 150mV - 12V What is in the box: 2-Channel amplifier Four 1-1/2" Screws 5mm Allen wrench Quick setup instructions Certificate of Performance Rockford Fosgate Punch P300X2 owner's manual Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Punch P300X2 300W RMS Punch Series 2-Channel Stereo Class AB Car Power Amplifier The Punch P300X2 is a 2-channel stereo amplifier capable of producing 150 Watts into each channel at 2-ohms. It is great for driving a pair of coaxial speakers, component speakers, or a single subwoofer. The amplifier can also be run simultaneously in stereo/mono mode when using passive crossovers (not supplied) on all speakers. With proven PUNCH technology, the P300X2 delivers real Rockford Fosgate power from a small design and is flexible enough to accommodate any moderately sized system. General Features: Punch Series 2-Channel Class AB Car Amplifier RMS Power Rating: 4 ohms: 100 watts x 2 Channel 2 ohms: 150 watts x 2 Channel Bridged, 4 ohms: 300 watts x 1 chan. CEA-2006 compliant amplifier Features C.L.E.A.N. Set-up with input/output clip detection and indicator LEDs MOSFET power supply Muted turn on Cast aluminum heatsink 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protection indicators Nickel-plated captive C-clamp terminals Ultra-efficient Class BD circuitry to maximize amplifier power efficiency On-board differential inputs eliminate noise picked up by the signal cable Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately) MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low DSM (Discrete Surface Mounted Components) utilizes 1% tight-tolerances, improving the efficiency of the circuit and lowering the operating temperature and potential for noise, similar to circuit boards designed by aerospace manufacturers Input sensitivity: 150mV - 12V What is in the box: 2-Channel amplifier Four 1-1/2" Screws 5mm Allen wrench Quick setup instructions Certificate of Performance Rockford Fosgate Punch P300X2 owner's manual Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.