Rockford Fosgate All Amplifiers (80)

Rockford Fosgate Punch P1000X5 5-channel car amplifier — 75 watts RMS x 4 at 4 ohms + 500 watts RMS x 1 at 1 ohm The Punch P1000X5 is an ultra-efficient 5-channel amplifier capable of running your entire system without excessive drain on your charging system. The P1000X5 is perfect for running a front/rear system and a dedicated subwoofer. The P1000X5 1,000 Watt full-range 5-channel is the one-and-only amplifier you will need to run your entire system. Run dash speakers off the front channels, run back speakers off the rear channels, and run subwoofer(s) off the 5th channel! Known worldwide for brute power, this amplifier offers higher efficiency along with tri-stage protection that covers thermal, over-current, and short circuits. General Features: 5-channel car amplifier 75 watts RMS x 4 + 150 watts RMS x 1 at 4 ohms 125 watts RMS x 4 + 300 watts RMS x 1 at 2 ohms 250 watts RMS x 2 bridged at 4 ohms + 500 watts RMS at 1 ohm CEA-2006 compliant variable high- and low-pass filters (50-250 Hz, 12 dB/octave) variable PEQ2 bass/treble boost (0-18 dB at 45 Hz and 0-14 dB at 12.5K Hz) switchable subsonic filter (28 Hz, 12 dB/octave) on subwoofer channel L.E.A.N. gain setup system includes test tone CD Test tones are also available as MP3 downloads from Amazon on Demand, Rhapsody, Google Play, and Spotify, labeled "3sixty..3 setup disc" (Punch amps and the 3sixty..3 use the same test tone tracks for setup) Class-BD amplifier design frequency response: 20-20K Hz Dynamic Thermal Management and MEHSA MOSFET cooling systems MOSFET power and output stages preamp and speaker-level inputs (speaker-level inputs require a speaker wire to RCA adapter) signal-sensing turn-on with speaker-level inputs eliminates the need for a remote turn-on lead optional PLC2 wired remote level control with clip light available 4-gauge power and ground leads and a 150-amp fuse recommended — wiring and hardware not included with amplifier No onboard fuses — when installing multiple amps in a system, an additional 150-amp in-line fuse between the distribution block and the amplifier is recommended. 15-1/8"W x 2-7/16"H x 8-13/16"D What is in the box: 5-Channel amplifier Four 1-1/2" Self-tapping screws 5mm Allen wrench Quick setup instructions Certificate of Performance Setup/Manual disc Rockford Fosgate Punch P1000X5 owner's manual Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Punch P1000X5 5-channel car amplifier — 75 watts RMS x 4 at 4 ohms + 500 watts RMS x 1 at 1 ohm The Punch P1000X5 is an ultra-efficient 5-channel amplifier capable of running your entire system without excessive drain on your charging system. The P1000X5 is perfect for running a front/rear system and a dedicated subwoofer. The P1000X5 1,000 Watt full-range 5-channel is the one-and-only amplifier you will need to run your entire system. Run the dash speakers off the front channels, the back speakers off the rear channels, and the subwoofer(s) off the 5th channel! Known worldwide for brute power, this amplifier offers higher efficiency along with tri-stage protection that covers thermal, over-current, and short circuits. General Features: 5-channel car amplifier 75 watts RMS x 4 + 150 watts RMS x 1 at 4 ohms 125 watts RMS x 4 + 300 watts RMS x 1 at 2 ohms 250 watts RMS x 2 bridged at 4 ohms + 500 watts RMS at 1 ohm CEA-2006 compliant variable high- and low-pass filters (50-250 Hz, 12 dB/octave) variable PEQ2 bass/treble boost (0-18 dB at 45 Hz and 0-14 dB at 12.5K Hz) switchable subsonic filter (28 Hz, 12 dB/octave) on subwoofer channel L.E.A.N. gain setup system includes a test tone CD Test tones are also available as MP3 downloads from Amazon on Demand, Rhapsody, Google Play, and Spotify, labeled "3sixty..3 setup disc" (Punch amps and the 3sixty..3 use the same test tone tracks for setup) Class-BD amplifier design frequency response: 20-20K Hz Dynamic Thermal Management and MEHSA MOSFET cooling systems MOSFET power and output stages preamp and speaker-level inputs (speaker-level inputs require a speaker wire to RCA adapter) signal-sensing turn-on with speaker-level inputs eliminates the need for a remote turn-on lead optional PLC2 wired remote level control with clip light available 4-gauge power and ground leads and a 150-amp fuse recommended — wiring and hardware not included with amplifier No onboard fuses — when installing multiple amps in a system, an additional 150-amp in-line fuse between the distribution block and the amplifier is recommended. 15-1/8"W x 2-7/16"H x 8-13/16"D What is in the box: 5-Channel amplifier Four 1-1/2" Self-tapping screws 5mm Allen wrench Quick setup instructions Certificate of Performance Setup/Manual disc Rockford Fosgate Punch P1000X5 owner's manual Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Prime R2-750X1 750W Prime Series Monoblock Subwoofer Class D Amplifier Primed for performance, the R2-750X1 amplifier is a 750-watt, Class-D, capable of operating at 4Ω, 2Ω, or 1Ω mono. This amplifier is extremely efficient because of its Class-D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allow you to tune the bass for the desired level of the music. Rockford Fosgate's R2 amplifiers are the building blocks for great audio systems, powerful enough to even DRIVE our Punch speakers and subwoofers. They have undergone an amazing upgrade by packing them with the latest features at an incredible value. Best of all, they are designed and engineered here in Tempe, Arizona. General Features: Rockford Fosgate Prime R2-750X1 RMS Power Rating: 4 ohms: 250 watts x 1 channel RMS Power Rating: 2 ohms: 500 watts x 1 channel RMS Power Rating: 1 ohm: 750 watts x 1 channel Total power output: 500 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeatable Auto Turn on Circuit Features C.L.E.A.N. Set-up Variable Input Gain adjustment level R.L.C. Remote Level Control Variable Infrasonic Filter Continuously Variable On-Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Full Range Class D Rollback Protection Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers Input sensitivity: Low-Level: 150 mV - 4 V Input sensitivity: High-Level: 450 mV - 12 V Frequency Response: 20 Hz - 250 Hz Total Harmonic Distortion (THD): >1% Crossover Controls: Low-Pass: 50 Hz - 250 Hz Crossover Controls: Sub Infrasonic: 15 Hz - 40 Hz Recommended Fuse Rating: 120A 4-gauge power and ground wiring are recommended for installation. Dimensions: "1.9" x "6.8" x "10.1" Authorized Internet Dealer 1-Year Manufacturer's Warranty What is in the R2-750X1 package: Mono subwoofer amplifier Wired Remote Level Control module 16' Remote cable (RJ-25 connector on both ends) One 7" Speaker input harness 3mm Allen Hex key Four 3/4" Screws Two 1/2" Screws 5 Flat washers 1 Nut Installation and Operation Instructions Certificate of Performance Rockford Fosgate contact information Rockford Fosgate R2-500X1 owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Prime R2-750X1 750W Prime Series Monoblock Subwoofer Class D Amplifier Primed for performance, the R2-750X1 amplifier is a 750-watt, Class-D, capable of operating at 4Ω, 2Ω, or 1Ω mono. This amplifier is extremely efficient because of its Class-D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allow you to tune the bass for the desired level of the music. Rockford Fosgate's R2 amplifiers are the building blocks for great audio systems, powerful enough to even DRIVE our Punch speakers and subwoofers. They have undergone an amazing upgrade by packing them with the latest features at an incredible value. Best of all, they are designed and engineered here in Tempe, Arizona. General Features: Rockford Fosgate Prime R2-750X1 RMS Power Rating: 4 ohms: 250 watts x 1 channel RMS Power Rating: 2 ohms: 500 watts x 1 channel RMS Power Rating: 1 ohm: 750 watts x 1 channel Total power output: 500 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeatable Auto Turn on Circuit Features C.L.E.A.N. Set-up Variable Input Gain adjustment level R.L.C. Remote Level Control Variable Infrasonic Filter Continuously Variable On-Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Full Range Class D Rollback Protection Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers Input sensitivity: Low-Level: 150 mV - 4 V Input sensitivity: High-Level: 450 mV - 12 V Frequency Response: 20 Hz - 250 Hz Total Harmonic Distortion (THD): >1% Crossover Controls: Low-Pass: 50 Hz - 250 Hz Crossover Controls: Sub Infrasonic: 15 Hz - 40 Hz Recommended Fuse Rating: 120A 4-gauge power and ground wiring are recommended for installation. Dimensions: "1.9" x "6.8" x "10.1" Authorized Internet Dealer 1-Year Manufacturer's Warranty What is in the R2-750X1 package: Mono subwoofer amplifier Wired Remote Level Control module 16' Remote cable (RJ-25 connector on both ends) One 7" Speaker input harness 3mm Allen Hex key Four 3/4" Screws Two 1/2" Screws 5 Flat washers 1 Nut Installation and Operation Instructions Certificate of Performance Rockford Fosgate contact information Rockford Fosgate R2-500X1 owner's manual ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Prime R2-500X1 500W Prime Series Monoblock Subwoofer Class D Amplifier Primed for performance, the R2-500X1 amplifier is a 500 watt, class-D, capable of operating at 4Ω or 2Ω mono. This amplifier is extremely efficient because of its class D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allows you to tune the bass for the desired level for the music. General Features: Rockford Fosgate Prime R2-500X1 RMS Power Rating: 4 ohms: 300 watts x 1 chan. 2 ohms: 500 watts x 1 chan. Total power output: 500 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeat able Auto Turn-On Circuit Features C.L.E.A.N. Set-up Variable Input Gain adjustment level R.L.C. Remote Level Control Variable Infrasonic Filter Continuously Variable On Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Full Range Class D Rollback Protection Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers Input sensitivity: Low-Level: 150 mV - 4 V High-Level: 450 mV - 12 V Frequency Response: 20 Hz - 250 Hz Total Harmonic Distortion (THD): >1% Crossover Controls Low-Pass: 50 Hz - 250 Hz Sub Infrasonic: 15 Hz - 40 Hz Recommended Fuse Rating: 80A 4 gauge power and ground wiring is recommended for installation Dimensions: "1.9" x "6.8" x "8.5" Authorized Internet Dealer 1 Year Manufacturer's Warranty What is in the R2-500X1 package: Rockford Fosgate R2-500X1 owner's manual Mono subwoofer amplifier Wired Remote Level Control module 16' Remote cable (RJ-25 connector on both ends) One 7" Speaker input harnesses 3mm Allen Hex key Four 3/4" Screws Two 1/2" Screws 5 Flat washers 1 Nut Installation and Operation Instructions Certificate of Performance Rockford Fosgate contact information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca

Rockford Fosgate Prime R2-500X1 500W Prime Series Monoblock Subwoofer Class D Amplifier Primed for performance, the R2-500X1 amplifier is a 500 watt, class-D, capable of operating at 4Ω or 2Ω mono. This amplifier is extremely efficient because of its class D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass. For subwoofers, a variable infrasonic filter and remote level control allows you to tune the bass for the desired level for the music. General Features: Rockford Fosgate Prime R2-500X1 RMS Power Rating: 4 ohms: 300 watts x 1 chan. 2 ohms: 500 watts x 1 chan. Total power output: 500 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeat able Auto Turn-On Circuit Features C.L.E.A.N. Set-up Variable Input Gain adjustment level R.L.C. Remote Level Control Variable Infrasonic Filter Continuously Variable On Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Full Range Class D Rollback Protection Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers Input sensitivity: Low-Level: 150 mV - 4 V High-Level: 450 mV - 12 V Frequency Response: 20 Hz - 250 Hz Total Harmonic Distortion (THD): >1% Crossover Controls Low-Pass: 50 Hz - 250 Hz Sub Infrasonic: 15 Hz - 40 Hz Recommended Fuse Rating: 80A 4 gauge power and ground wiring is recommended for installation Dimensions: "1.9" x "6.8" x "8.5" Authorized Internet Dealer 1 Year Manufacturer's Warranty What is in the R2-500X1 package: Rockford Fosgate R2-500X1 owner's manual Mono subwoofer amplifier Wired Remote Level Control module 16' Remote cable (RJ-25 connector on both ends) One 7" Speaker input harnesses 3mm Allen Hex key Four 3/4" Screws Two 1/2" Screws 5 Flat washers 1 Nut Installation and Operation Instructions Certificate of Performance Rockford Fosgate contact information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca

Rockford Fosgate Punch P300X2 300W RMS Punch Series 2-Channel Stereo Class AB Car Power Amplifier The Punch P300X2 is a 2-channel stereo amplifier capable of producing 150 Watts into each channel at 2-ohms. It is great for driving a pair of coaxial speakers, component speakers, or a single subwoofer. The amplifier can also be run simultaneously in stereo/mono mode when using passive crossovers (not supplied) on all speakers. With proven PUNCH technology, the P300X2 delivers real Rockford Fosgate power from a small design and is flexible enough to accommodate any moderately sized system. General Features: Punch Series 2-Channel Class AB Car Amplifier RMS Power Rating: 4 ohms: 100 watts x 2 Channel 2 ohms: 150 watts x 2 Channel Bridged, 4 ohms: 300 watts x 1 chan. CEA-2006 compliant amplifier Features C.L.E.A.N. Set-up with input/output clip detection and indicator LEDs MOSFET power supply Muted turn on Cast aluminum heatsink 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protection indicators Nickel-plated captive C-clamp terminals Ultra-efficient Class BD circuitry to maximize amplifier power efficiency On-board differential inputs eliminate noise picked up by the signal cable Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately) MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low DSM (Discrete Surface Mounted Components) utilizes 1% tight-tolerances, improving the efficiency of the circuit and lowering the operating temperature and potential for noise, similar to circuit boards designed by aerospace manufacturers Input sensitivity: 150mV - 12V What is in the box: 2-Channel amplifier Four 1-1/2" Screws 5mm Allen wrench Quick setup instructions Certificate of Performance Rockford Fosgate Punch P300X2 owner's manual Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Punch P300X2 300W RMS Punch Series 2-Channel Stereo Class AB Car Power Amplifier The Punch P300X2 is a 2-channel stereo amplifier capable of producing 150 Watts into each channel at 2-ohms. It is great for driving a pair of coaxial speakers, component speakers, or a single subwoofer. The amplifier can also be run simultaneously in stereo/mono mode when using passive crossovers (not supplied) on all speakers. With proven PUNCH technology, the P300X2 delivers real Rockford Fosgate power from a small design and is flexible enough to accommodate any moderately sized system. General Features: Punch Series 2-Channel Class AB Car Amplifier RMS Power Rating: 4 ohms: 100 watts x 2 Channel 2 ohms: 150 watts x 2 Channel Bridged, 4 ohms: 300 watts x 1 chan. CEA-2006 compliant amplifier Features C.L.E.A.N. Set-up with input/output clip detection and indicator LEDs MOSFET power supply Muted turn on Cast aluminum heatsink 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protection indicators Nickel-plated captive C-clamp terminals Ultra-efficient Class BD circuitry to maximize amplifier power efficiency On-board differential inputs eliminate noise picked up by the signal cable Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately) MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low DSM (Discrete Surface Mounted Components) utilizes 1% tight-tolerances, improving the efficiency of the circuit and lowering the operating temperature and potential for noise, similar to circuit boards designed by aerospace manufacturers Input sensitivity: 150mV - 12V What is in the box: 2-Channel amplifier Four 1-1/2" Screws 5mm Allen wrench Quick setup instructions Certificate of Performance Rockford Fosgate Punch P300X2 owner's manual Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Prime R2-500X4 500W Prime Series 4-Channel Full Range Class D Amplifier Primed for performance, the R2-500X4 is a 500-watt, full-range Class-D amplifier capable of operating at 4Ω or 2Ω stereo and 4Ω bridged/mono. This amplifier is extremely efficient because of its Class-D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. supply that generates more power as voltage increases. Rockford Fosgate's R2 amplifiers are the building blocks for great audio systems, powerful enough to even DRIVE our Punch speakers and subwoofers. They have undergone an amazing upgrade by packing them with the latest features at an incredible value. Best of all, they are designed and engineered here in Tempe, Arizona. General Features: Rockford Fosgate Prime R2-500X4 RMS Power Rating: 4 ohms: 75 watts x 4 Channel RMS Power Rating: 2 ohms: 125 watts x 4 Channel Bridged, 4 ohms: 250 watts x 2 Channel Total power output: 500 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeatable Auto Turn on Circuit Features C.L.E.A.N. Set-up 2/4 Channel Input Selection Switch Front and Rear Variable Input Gain adjustment level Continuously Variable On-Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Rollback Protection Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers Frequency Response: 20 Hz - 20 kHz Total Harmonic Distortion (THD): >1% Signal to Noise Ratio: xx dB Variable high-pass filter: 50 - 250 Hz, 24 dB/octave Variable low-pass filter: 50 - 250Hz, 24 dB/octave Recommended Fuse Rating: 80A 4-gauge power and ground wiring are recommended for installation Dimensions: 1.9" x "6.8" x "10.1" Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the R2-500X4 package: R2-500X4 owner's manual 4-Channel amplifier Two 7" Speaker input harnesses 3mm Allen Hex key Four 3/4" Screws 4 Flat washers Installation and Operation Instructions Certificate of Performance Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca

Rockford Fosgate Prime R2-500X4 500W Prime Series 4-Channel Full Range Class D Amplifier Primed for performance, the R2-500X4 is a 500-watt, full-range Class-D amplifier capable of operating at 4Ω or 2Ω stereo and 4Ω bridged/mono. This amplifier is extremely efficient because of its Class-D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. supply that generates more power as voltage increases. Rockford Fosgate's R2 amplifiers are the building blocks for great audio systems, powerful enough to even DRIVE our Punch speakers and subwoofers. They have undergone an amazing upgrade by packing them with the latest features at an incredible value. Best of all, they are designed and engineered here in Tempe, Arizona. General Features: Rockford Fosgate Prime R2-500X4 RMS Power Rating: 4 ohms: 75 watts x 4 Channel RMS Power Rating: 2 ohms: 125 watts x 4 Channel Bridged, 4 ohms: 250 watts x 2 Channel Total power output: 500 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeatable Auto Turn on Circuit Features C.L.E.A.N. Set-up 2/4 Channel Input Selection Switch Front and Rear Variable Input Gain adjustment level Continuously Variable On-Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Rollback Protection Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers Frequency Response: 20 Hz - 20 kHz Total Harmonic Distortion (THD): >1% Signal to Noise Ratio: xx dB Variable high-pass filter: 50 - 250 Hz, 24 dB/octave Variable low-pass filter: 50 - 250Hz, 24 dB/octave Recommended Fuse Rating: 80A 4-gauge power and ground wiring are recommended for installation Dimensions: 1.9" x "6.8" x "10.1" Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the R2-500X4 package: R2-500X4 owner's manual 4-Channel amplifier Two 7" Speaker input harnesses 3mm Allen Hex key Four 3/4" Screws 4 Flat washers Installation and Operation Instructions Certificate of Performance Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca

Rockford Fosgate Punch P400X4 4-channel car amplifier 50 watts RMS x 4 Big power for your speakers or subwoofersRockford Fosgate's Punch P400X4 amplifier can put 50 watts RMS to each of your front and rear speakers, which is plenty of power for clean music even at high levels. You can use the amp's high-pass filter to remove low bass from your speakers, so they'll play more efficiently. You can also switch this amp into 2-channel mode to drive a couple of subwoofers with up to 200 watts RMS each. The amp's low-pass filter is handy for getting the right sound from your sub/enclosure combo. The Punch EQ2 includes bass and treble boosts if you want to add some boom and sizzle back into the mix. Easy to set for optimum performanceOnce again, Rockford Fosgate steps away from the crowd with their C.L.E.A.N. technology (Calibrated Level Eliminates Audible Noise). This setup system ensures your music will sound as clean and powerful as possible. It works like this: first, download the setup tones from Rockford Fosgate, then play the tone, adjust the receiver volume until a red clip light on the amp goes out, then turn the amp gain up until a blue light comes on. It's that simple — your amplifier will be perfectly set to match your receiver's output. When your receiver reaches maximum clean volume, you'll get maximum clean power from your Power amp. You'll hear less background noise and more of your music at quiet listening levels. Keeps an eye on things while playingIf that blue light turns solid red while you're playing music, the amp tells you that your source is distorting, and you should turn it down or risk damage to your gear. The amp's built-in computer keeps tabs on the output current, ensuring that plunging speaker impedances (they change during play) or a short circuit won't hurt anything. Maintaining coolness raises efficiency and lowers distortion.Rockford Fosgate's Dynamic Thermal Management system uses forced air to dissipate heat evenly across the amp and out through the high mass heatsink, efficiently drawing heat away from vital internal parts. Their proprietary MEHSA cooling process maximizes the heat transfer from the MOSFET devices to the heatsink, allowing the heat to escape more readily, so the transistors stay cooler and work better. General Features: 4-channel car amplifier 50 watts RMS x 4 at 4 ohms (100 watts RMS x 4 at 2 ohms) 200 watts RMS x 2 bridged at 4 ohms (4-ohm stable in bridged mode) CEA-2006 compliant variable high- and low-pass filter (50-250 Hz, 12 dB/octave) variable PEQ2 bass/treble boost (0-18 dB at 45 Hz and 0-14 dB at 12.5K Hz) C.L.E.A.N. gain setup system includes clip lights and links to Rockford Fosgate's setup tones Class-AB amplifier design frequency response: 20-20K Hz Dynamic Thermal Management and MEHSA MOSFET cooling systems MOSFET power and output stages preamp and speaker-level inputs (speaker wire to RCA adapter required for speaker-level input) signal-sensing turn-on with speaker-level inputs eliminates the need for a remote turn-on lead 4-gauge power and ground leads and a 60-amp fuse recommended — wiring and hardware not included with amplifier 11-1/8"W x 2-7/16"H x 8-13/16"D warranty: 1 year Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Punch P400X4 4-channel car amplifier 50 watts RMS x 4 Big power for your speakers or subwoofersRockford Fosgate's Punch P400X4 amplifier can put 50 watts RMS to each of your front and rear speakers, which is plenty of power for clean music even at high levels. You can use the amp's high-pass filter to remove low bass from your speakers, so they'll play more efficiently. You can also switch this amp into 2-channel mode to drive a couple of subwoofers with up to 200 watts RMS each. The amp's low-pass filter is handy for getting the right sound from your sub/enclosure combo. The Punch EQ2 includes bass and treble boosts if you want to add some boom and sizzle back into the mix. Easy to set for optimum performanceOnce again, Rockford Fosgate steps away from the crowd with their C.L.E.A.N. technology (Calibrated Level Eliminates Audible Noise). This setup system ensures your music will sound as clean and powerful as possible. It works like this: first, download the setup tones from Rockford Fosgate, then play the tone, adjust the receiver volume until a red clip light on the amp goes out, then turn the amp gain up until a blue light comes on. It's that simple — your amplifier will be perfectly set to match your receiver's output. When your receiver reaches maximum clean volume, you'll get maximum clean power from your Power amp. You'll hear less background noise and more of your music at quiet listening levels. Keeps an eye on things while playingIf that blue light turns solid red while you're playing music, the amp tells you that your source is distorting, and you should turn it down or risk damage to your gear. The amp's built-in computer keeps tabs on the output current, ensuring that plunging speaker impedances (they change during play) or a short circuit won't hurt anything. Maintaining coolness raises efficiency and lowers distortion.Rockford Fosgate's Dynamic Thermal Management system uses forced air to dissipate heat evenly across the amp and out through the high mass heatsink, efficiently drawing heat away from vital internal parts. Their proprietary MEHSA cooling process maximizes the heat transfer from the MOSFET devices to the heatsink, allowing the heat to escape more readily, so the transistors stay cooler and work better. General Features: 4-channel car amplifier 50 watts RMS x 4 at 4 ohms (100 watts RMS x 4 at 2 ohms) 200 watts RMS x 2 bridged at 4 ohms (4-ohm stable in bridged mode) CEA-2006 compliant variable high- and low-pass filter (50-250 Hz, 12 dB/octave) variable PEQ2 bass/treble boost (0-18 dB at 45 Hz and 0-14 dB at 12.5K Hz) C.L.E.A.N. gain setup system includes clip lights and links to Rockford Fosgate's setup tones Class-AB amplifier design frequency response: 20-20K Hz Dynamic Thermal Management and MEHSA MOSFET cooling systems MOSFET power and output stages preamp and speaker-level inputs (speaker wire to RCA adapter required for speaker-level input) signal-sensing turn-on with speaker-level inputs eliminates the need for a remote turn-on lead 4-gauge power and ground leads and a 60-amp fuse recommended — wiring and hardware not included with amplifier 11-1/8"W x 2-7/16"H x 8-13/16"D warranty: 1 year Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.