Class-D Amplifiers (324)

Alpine KTA-30FW 600W Max, 300W RMS KTA Series 4 ohm Stable 4-Channel Class-D Tough Power Pack Amplifier Half The Size, Double The Power Get a huge increase in sound performance over your factory system. With Alpine’s exclusive technology, Dynamic Peak Power (D.P.P.), the KTA-30FW Weather Resistant Tough Power Pack is sure to add higher output and increased dynamic range for those open cab vehicles and toys. The KTA-F30W is perfect for when you want to boost your sound system but don’t have space for a large amplifier. It is compatible with an aftermarket or factory head unit and adds up to 4 times the power over the head unit's original built-in power. The KTA-30FW is ready for your adventures. It is weather-resistant, rated at IP66 for protection against dust ingress and high-pressure water spray. The KTA-30FW features a rugged chassis and high-quality waterproof connector so it can be used in installations where it will be exposed to the elements, like side-by-sides, boats, open-top vehicles. and motorcycles. General Features: Alpine KTA-30FW Class-D Full Range 4-Ohm Stable 4-Channel Amplifier Designed for use in Side-by-Sides, Boats, Open-Top Vehicles, and Motorcycles RMS Power Rating: 4 ohms: 75 watts x 4 Channel RMS Power Rating: 2 ohms: 75 watts x 4 Channel 150 watts RMS x 2 bridged at 4 ohms (4-ohm stable in bridged mode) Total power output: 600 watts CEA-2006 Compliant Amplifier Power Wire Harness Included Pulse Width Modulated MOSFET power supply Wired remote bass level control included Soft start turn-on Switchable 4 or 2 channel operation Speaker-level (high-level) inputs Preamp RCA outputs to daisy chain multiple amps 3-way protection circuitry (thermal, overload, and speaker short protection) Dual speaker terminals simplify the hookup of multiple speakers Heavy-duty aluminum alloy heat-sink IP66 Waterproof Rating Input sensitivity: Low level: 0.2V-4V Input sensitivity: High level: 0.5V-10V Frequency Response: 15 - 36000 Hz Total Harmonic Distortion (THD): <0.1% Signal to Noise Ratio: >98 dB Variable high-pass filter: 50 - 400 Hz, 12 dB/octave Variable low-pass filter: 50 - 400 Hz, 12 dB/octave Variable Bass Boost: 0 to +12 dB bass boost at 50 Hz Dimensions: 9-3/16"W x 3-3/4"D x 1-3/4"H Authorized Dealer 1-year Manufacturer's Warranty What is in the box: 4-Channel amplifier 14" Power/signal harness (26-pin connector on one end and bare wires + RCAs on other ends) 4 Self-tapping screws (Length 3/4") Connection sheet Limited Warranty sheet Thank you letter Alpine KTA-30FW Tough Power Pack owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine KTA-30FW 600W Max, 300W RMS KTA Series 4 ohm Stable 4-Channel Class-D Tough Power Pack Amplifier Half The Size, Double The Power Get a huge increase in sound performance over your factory system. With Alpine’s exclusive technology, Dynamic Peak Power (D.P.P.), the KTA-30FW Weather Resistant Tough Power Pack is sure to add higher output and increased dynamic range for those open cab vehicles and toys. The KTA-F30W is perfect for when you want to boost your sound system but don’t have space for a large amplifier. It is compatible with an aftermarket or factory head unit and adds up to 4 times the power over the head unit's original built-in power. The KTA-30FW is ready for your adventures. It is weather-resistant, rated at IP66 for protection against dust ingress and high-pressure water spray. The KTA-30FW features a rugged chassis and high-quality waterproof connector so it can be used in installations where it will be exposed to the elements, like side-by-sides, boats, open-top vehicles. and motorcycles. General Features: Alpine KTA-30FW Class-D Full Range 4-Ohm Stable 4-Channel Amplifier Designed for use in Side-by-Sides, Boats, Open-Top Vehicles, and Motorcycles RMS Power Rating: 4 ohms: 75 watts x 4 Channel RMS Power Rating: 2 ohms: 75 watts x 4 Channel 150 watts RMS x 2 bridged at 4 ohms (4-ohm stable in bridged mode) Total power output: 600 watts CEA-2006 Compliant Amplifier Power Wire Harness Included Pulse Width Modulated MOSFET power supply Wired remote bass level control included Soft start turn-on Switchable 4 or 2 channel operation Speaker-level (high-level) inputs Preamp RCA outputs to daisy chain multiple amps 3-way protection circuitry (thermal, overload, and speaker short protection) Dual speaker terminals simplify the hookup of multiple speakers Heavy-duty aluminum alloy heat-sink IP66 Waterproof Rating Input sensitivity: Low level: 0.2V-4V Input sensitivity: High level: 0.5V-10V Frequency Response: 15 - 36000 Hz Total Harmonic Distortion (THD): <0.1% Signal to Noise Ratio: >98 dB Variable high-pass filter: 50 - 400 Hz, 12 dB/octave Variable low-pass filter: 50 - 400 Hz, 12 dB/octave Variable Bass Boost: 0 to +12 dB bass boost at 50 Hz Dimensions: 9-3/16"W x 3-3/4"D x 1-3/4"H Authorized Dealer 1-year Manufacturer's Warranty What is in the box: 4-Channel amplifier 14" Power/signal harness (26-pin connector on one end and bare wires + RCAs on other ends) 4 Self-tapping screws (Length 3/4") Connection sheet Limited Warranty sheet Thank you letter Alpine KTA-30FW Tough Power Pack owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine KTA-30FW 600W Max, 300W RMS KTA Series 4 ohm Stable 4-Channel Class-D Tough Power Pack Amplifier Half The Size, Double The Power Get a huge increase in sound performance over your factory system. With Alpine’s exclusive technology, Dynamic Peak Power (D.P.P.), the KTA-30FW Weather Resistant Tough Power Pack is sure to add higher output and increased dynamic range for those open cab vehicles and toys. The KTA-F30W is perfect for when you want to boost your sound system but don’t have space for a large amplifier. It is compatible with an aftermarket or factory head unit and adds up to 4 times the power over the head unit's original built-in power. The KTA-30FW is ready for your adventures. It is weather-resistant, rated at IP66 for protection against dust ingress and high-pressure water spray. The KTA-30FW features a rugged chassis and high-quality waterproof connector so it can be used in installations where it will be exposed to the elements, like side-by-sides, boats, open-top vehicles. and motorcycles. General Features: Alpine KTA-30FW Class-D Full Range 4-Ohm Stable 4-Channel Amplifier Designed for use in Side-by-Sides, Boats, Open-Top Vehicles, and Motorcycles RMS Power Rating: 4 ohms: 75 watts x 4 Channel RMS Power Rating: 2 ohms: 75 watts x 4 Channel 150 watts RMS x 2 bridged at 4 ohms (4-ohm stable in bridged mode) Total power output: 600 watts CEA-2006 Compliant Amplifier Power Wire Harness Included Pulse Width Modulated MOSFET power supply Wired remote bass level control included Soft start turn-on Switchable 4 or 2 channel operation Speaker-level (high-level) inputs Preamp RCA outputs to daisy chain multiple amps 3-way protection circuitry (thermal, overload, and speaker short protection) Dual speaker terminals simplify the hookup of multiple speakers Heavy-duty aluminum alloy heat-sink IP66 Waterproof Rating Input sensitivity: Low level: 0.2V-4V Input sensitivity: High level: 0.5V-10V Frequency Response: 15 - 36000 Hz Total Harmonic Distortion (THD): <0.1% Signal to Noise Ratio: >98 dB Variable high-pass filter: 50 - 400 Hz, 12 dB/octave Variable low-pass filter: 50 - 400 Hz, 12 dB/octave Variable Bass Boost: 0 to +12 dB bass boost at 50 Hz Dimensions: 9-3/16"W x 3-3/4"D x 1-3/4"H Authorized Dealer 1-year Manufacturer's Warranty What is in the box: 4-Channel amplifier 14" Power/signal harness (26-pin connector on one end and bare wires + RCAs on other ends) 4 Self-tapping screws (Length 3/4") Connection sheet Limited Warranty sheet Thank you letter Alpine KTA-30FW Tough Power Pack owner's manual ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Diamond Audio HX1600.1D 1600 Watt RMS Mono Amplifier The Diamond Audio HX1600.1D single channel 1600 watt RMS amplifier is specifically designed for extreme use sound systems that need a small size but major power output. This amp will push any subwoofer you give it, and it'll do it all while staying cool with an anodized extruded aluminum heat sink which provides superior thermal performance. General Features: Anodized Extruded Aluminum Heat Sink Provides Superior Thermal Performance 4-Layer PCB Board with Balanced Differential Inputs Full Range Class D IR Chipset “SNAP” Capacitors used Throughout the Circuit Audiophile Grade High Tolerance Components Spring Steel FET Clips Provide a Cleaner Board Design Illuminated Logo / Fully Concealed Mounting Output Clip Indicators for Precise Set-Up Fine Tuned Fully Variable Crossovers and Phase Control Top Mounted Controls for Convenient Amplifier Adjustment Specification:RMS Power Rating RMS Power (4Ω): 700 W RMS RMS Power (2Ω): 1150 W RMS RMS Power (1Ω): 1600 W RMS Type Topology: Class D Power Supply Power Supply: Full PWM Power Supply Threshold: 10.0VDC-170VDC Idle Current: (0.7A) Distortion THD 4(1KH@4Ω) : 0.01% S/N Ratio(A weighted@1W): -80dBA S/N Ratio(A weighted@FP): -95dBA Input Sensitivity Low Input Level: 200mV-5.0V High Input Level: N/A Input Impedance Low Input Level: 20 KΩ High Input Level: N/A Output Stage Output Impedance: 0.018 Ω Damping Factor(50Hz@4Ω): >250 Bandwidth(-3dB): 10Hz-300Hz Crossover(-12dB/Oct) Variable High-Pass: N/A Variable Low-Pass: 30Hz-300Hz Variable Sub-Sonic: 10Hz-55Hz@12dB Fuse Ratings ATC: 40A X 4 Dimensions Length x Width x Height(Inches): 15.8" x 7.67" x 2" Length x Width x Height(mm): 402 x 195 x 51.5 ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Diamond Audio HX1600.1D 1600 Watt RMS Mono Amplifier The Diamond Audio HX1600.1D single channel 1600 watt RMS amplifier is specifically designed for extreme use sound systems that need a small size but major power output. This amp will push any subwoofer you give it, and it'll do it all while staying cool with an anodized extruded aluminum heat sink which provides superior thermal performance. General Features: Anodized Extruded Aluminum Heat Sink Provides Superior Thermal Performance 4-Layer PCB Board with Balanced Differential Inputs Full Range Class D IR Chipset “SNAP” Capacitors used Throughout the Circuit Audiophile Grade High Tolerance Components Spring Steel FET Clips Provide a Cleaner Board Design Illuminated Logo / Fully Concealed Mounting Output Clip Indicators for Precise Set-Up Fine Tuned Fully Variable Crossovers and Phase Control Top Mounted Controls for Convenient Amplifier Adjustment Specification:RMS Power Rating RMS Power (4Ω): 700 W RMS RMS Power (2Ω): 1150 W RMS RMS Power (1Ω): 1600 W RMS Type Topology: Class D Power Supply Power Supply: Full PWM Power Supply Threshold: 10.0VDC-170VDC Idle Current: (0.7A) Distortion THD 4(1KH@4Ω) : 0.01% S/N Ratio(A weighted@1W): -80dBA S/N Ratio(A weighted@FP): -95dBA Input Sensitivity Low Input Level: 200mV-5.0V High Input Level: N/A Input Impedance Low Input Level: 20 KΩ High Input Level: N/A Output Stage Output Impedance: 0.018 Ω Damping Factor(50Hz@4Ω): >250 Bandwidth(-3dB): 10Hz-300Hz Crossover(-12dB/Oct) Variable High-Pass: N/A Variable Low-Pass: 30Hz-300Hz Variable Sub-Sonic: 10Hz-55Hz@12dB Fuse Ratings ATC: 40A X 4 Dimensions Length x Width x Height(Inches): 15.8" x 7.67" x 2" Length x Width x Height(mm): 402 x 195 x 51.5 ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

  Diamond Audio MICRO1V2 Monoblock 500W RMS Class D Amplifier Elite sound quality and superior power in an ultra-compact chassis. The Diamond Audio Micro1v2, one channel power amplifier, sets the standard for high-end Harley-specific amplifiers. The sound quality in a small footprint can be found in Diamond Audio’s MICROV2 amplifiers. Featuring ultra-efficient entire Range Class D IR Chipset DirectFET Power Mosfet Output Stage SMD Technology on four layer Glass PC Board ICAD circuit provides superior overload protection, these compact amplifiers deliver immense power for their size! The added feature of advanced Rollback/Thermal protection allows you to enjoy continuous and uninterrupted play without shutting down. Installation possibilities are endless! When looking for quality and performance in a small package, look to MICROV2 from Diamond Audio. General Features: Ultra-compact, high-density aluminum alloy chassis provides superior thermal stability. Four-layer, glass epoxy circuit board for enhanced performance and reliability Full Range Class D amplifier technology Balanced differential inputs for superior noise rejection Input sensitivity from 200mV to 10V accepts Line (RCA) and Speaker level input Selectable auto-turn-on modes: Signal Sensing (VOX), 12V Remote (REM), and DC offset (DC) Fully variable, 12dB per octave, electronic crossover Variable 18dB per octave sub-sonic filter Adjustable Bass EQ (45Hz: 0dB to +12dB) / remote level control included Illuminated logo Specifications: RMS Power Rating: RMS Power (2Ω): 300W RMS Power (4Ω): 175W Bridged (mono 1Ω): 500W Bridged (mono 2Ω): 300W Bridged (mono 4Ω): 175W Topology: Full Range Class D Power Supply: Power Supply: Full PWM Power Supply Threshold: 10.0VDC - 17.0VDC Idle Current: (0.7A) Distortion: THD 4 (1KHx @ 4Ω): 0.5% S/N Ratio (A weighted @1W): -85dBA S/N Ratio (A weighted @FP): -101.1dBA Input Sensitivity: Low Input Level: 200mV - 10.0V High Input Level: N/A Input Impedance: Low Input Level: 20KΩ High Input Level: 20KΩ Output Stage: Output Impedance: 0.011Ω Damping Factor (50Hz@4Ω): >250 Bandwidth (-3dB): 10Hz - 350Hz Crossover (-12dB/Oct): Variable High-Pass: N/A Variable Low-Pass: 40Hz - 400Hz Variable Sun-Sonic: 10Hz - 55Hz Fuse Ratings: ATC: 25A Dimensions: 7.89” L x 4.0” W x 1.46” H ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Diamond Audio HXM800.1D Monoblock 800 Watts RMS Class D HXM Series Amplifier The Diamond Audio HXM800.1D is a marine-grade motorsport amplifier that boasts 800 watts RMS on a single channel. Perfect for your system that needs to push a subwoofer to the max while using minimal space. General Features: Ultra-compact, high-density aluminum alloy chassis provides superior thermal stability. Four-layer, glass epoxy circuit board for enhanced performance and reliability Circuit board conformal coated (water resistant) for marine applications Full Range Class D amplifier technology Balanced differential inputs for superior noise rejection Input sensitivity from 200mV to 10V accepts Line (RCA) and Speaker level input Selectable auto-turn-on modes: Signal Sensing (VOX), 12V Remote (REM) and DC offset (DC) Fully variable, 12dB per octave, electronic crossover Variable 18dB per octave sub-sonic filter Phase adjustable from 0 to 180 degrees Adjustable Bass EQ (45Hz: 1dB to +12dB) / remote level control included Built-in BTR Port (MICRO-USB) to connect our optional Bluetooth receiver-controller Top-mounted controls for convenient adjustment Integrated soft clip light for quick system set-up Illuminated logo RMS Power Rating RMS Power (1Ω): 800 W X 1 RMS Power (2Ω): 550 W X 1 RMS Power (4Ω): 350 W X 1 Type Topology: MonoBlock Class D Power Supply Power Supply: Full PWM Power Supply Threshold: 10.0VDC-17.0VDC Idle Current: (0.7A) Distortion THD (1KHz@4Ω) : 0.05% S/N Ratio (A weighted@1W): -77.2dBA S/N Ratio (A weighted@FP): -98.9dBA Input Sensitivity Low Input Level: .2mV-10.0V High Input Level: Yes - Up to 25W RMS Input Impedance Low Input Level: 22 KΩ High Input Level: 22 KΩ Output Stage Output Impedance: 0.047Ω Damping Factor (50Hz@4Ω): >250 Bandwidth (-3dB): 10Hz-350Hz Crossover (-12dB per Octave) Variable High-Pass: N/A Variable Low-Pass: 30Hz - 300Hz Variable Sub-Sonic: 10Hz - 55Hz Recommended Fuse Rating ATC: N/A Dimensions Length x Width x Height (Inches): 8.56 x 5.27 x 1.75 Length x Width x Height (mm): 297.6 x 133.9 x 44.5 ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Diamond Audio HX1200.1D HEX Series Monoblock Class-D Car Audio Amplifier It is introducing the all-new range of Diamond Audio HEX series amplifiers, made for ultimate sound quality and performance. It features a four-layer glass epoxy circuit board, top-mounted controls, and a brushed copper look exterior, making it great for a show car. General Features: Anodized Extruded Aluminum Heat Sink provides superior thermal performance 4-Layer PCB Board with balanced differential inputs Full Range Class D IR Chipset "Snap" capacitors are used throughout the circuit Audiophile Grade High Tolerance Components Spring Steel FET Clips provide a cleaner board design Illuminated logo / fully concealed mounting Output clip indicators for precise setup Fine-tuned fully variable crossovers and phase control Top-mounted controls for convenient amplifier adjustment Monoblock Class-D Amplifier RMS Power Rating: 4 Ohm: 540 watts x 1 Channel RMS Power Rating: 2 Ohm: 870 watts x 1 Channel RMS Power Rating: 1 Ohm: 1200 watts x 1 Channel Frequency Response: 10Hz - 300Hz Variable Low-Pass Filter (12dB/Octave): 30Hz - 300Hz Variable Sub-Sonic Filter (12dB/Octave): 10Hz - 55Hz Top Mounted Controls Anodized Extruded Aluminum Heat Sink 4-Layer PCB Board Balanced Differential Inputs Illuminated Logo Dimensions: 14.2" (362mm) x 7.67" (195mm) x 2" (51.5mm) 1-Year Warranty What is Included? One (1) Diamond Audio HX1200.1D HEX Series Monoblock Class-D Car Audio Amplifier ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Diamond Audio MICRO2V2 Micro Series 500W 2-Channel Class-D Car Audio Amplifier Elite sound quality and superior power in an ultra-compact chassis. The Diamond Audio Micro2v2 2-channel power amplifier sets the standard for high-end Harley-specific amplifiers. Featuring ultra-efficient full range class D topology and ICAD circuit that provides superior overload protection, these compact amplifiers deliver huge power for their size. Its compact design not only has the juice to power your system but will also save you a ton of space in your car or transport whatever you need it. The sound quality in a small footprint chassis can be found with Diamond Audio’s Micro series amplifiers. Featuring the ultra-efficient full-range Class D topology, these compact amplifiers deliver serious power making them the best in class. Installation possibilities are endless due to its size and power amplification output. Even with its small platform, performance and sound quality are never sacrificed with Micro amplifiers from Diamond Audio! General Features: Ultra-compact, high-density aluminum alloy chassis provides superior thermal stability Four-layer, glass epoxy circuit board for enhanced performance and reliability Full Range Class D amplifier technology Balanced differential inputs for superior noise rejection Input sensitivity from 200mV to 10V accepts Line (RCA) and Speaker level input Selectable auto-turn-on modes: Signal Sensing (VOX), 12V Remote (REM), and DC offset (DC) Fully variable, 12dB per octave, electronic crossover Variable 18dB per octave sub-sonic filter Adjustable Bass EQ (45Hz: 0dB to +12dB) Wired Remote Level Control included Illuminated logo Specifications: RMS Power Rating: RMS Power (2Ω): 250W X 2 RMS Power (4Ω): 150W X 2 Bridged (mono 1Ω): N/A Bridged (mono 2Ω): N/A Bridged (mono 4Ω): 500W Topology: Full Range Class D Power Supply: Power Supply: Full PWM Power Supply Threshold: 10.0VDC - 17.0VDC Idle Current: (0.7A) Distortion: THD 4 (1KHx @ 4Ω): 0.5% S/N Ratio (A weighted @1W): -85dBA S/N Ratio (A weighted @FP): -101.1dBA Input Sensitivity: Low Input Level: 200mV - 10.0V High Input Level: up to 10.0V Input Impedance: Low Input Level: 20KΩ High Input Level: 20KΩ Output Stage: Output Impedance: 0.011Ω Damping Factor (50Hz@4Ω): >250 Bandwidth (-3dB): 10Hz - 350Hz Crossover (-12dB/Oct): Variable High-Pass:40Hz - 400Hz Variable Low-Pass: 40Hz - 400Hz Fuse Ratings: ATC: 25A Dimensions: 7.89” L x 4.0” W x 1.46” H ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Diamond Audio HXM800.2D 2-Channel 800 Watts RMS Class D Full-Range HXM Series Amplifier The Diamond Audio HXM800.2D is a marine-grade motorsport amplifier that boasts 800 watts RMS on a single channel. Perfect for your system that needs to push a subwoofer to the max while using minimal space. General Features: Motorsport Series 2-Channel Full-Range Class-D Marine Amplifier Power Output: 300W RMS x 2 @ 4Ω 400W RMS x 2 @ 2Ω 800 W x 1 @ 4Ω bridged Ultra-compact, high-density aluminum alloy chassis provides superior thermal stability Four-layer, glass epoxy circuit board for enhanced performance and reliability Circuit board conformal coated (water resistant) for marine applications Full Range Class D amplifier technology Bridgeable for high power operation Balanced differential inputs for superior noise rejection Input sensitivity from 200mV to 10V accepts Line (RCA) and Speaker level input Selectable auto-turn-on modes: Signal Sensing (VOX),12V Remote (REM), and DC offset (DC) Fully variable, 12 dB per octave, electronic crossover Full range, line-level outputs provided to send a signal to another amplifier Adjustable Bass EQ (MICRO-USB) to connect our optional Bluetooth receiver-controller Top-mounted controls for convenient adjustment Integrated soft clip light for quick system set-up Illuminated logo THD: 0.05% S/N Ratio: < 77.2 dB Low Input Level: 0.2mV - 10.0V Bandwith: 10Hz-35Hz Variable High-Pass: 40-400Hz @ 12dB / Oct Variable Low-Pass: 40-400Hz @ 12dB / Oct Bass Remote Included Dimensions: 9.74"L x 5.27"W x 1.75"H Authorized Internet Dealer 1-year Manufacturer's Warranty ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Diamond Audio MICRO4V2 Micro Series 600W 4-Channel Class-D Car Audio Amplifier Elite sound quality and superior power in an ultra-compact chassis. The Diamond Audio Micro4v2 4-channel power amplifier sets the standard for high-end Harley-specific amplifiers. Featuring ultra-efficient full-range class D topology and ICAD circuit that provides superior overload protection, these compact amplifiers deliver huge power for their size. Its compact design has the juice to power your system and will save you a ton of space in your car or transport whatever you need. The sound quality in a small footprint chassis can be found with Diamond Audio’s Micro series amplifiers. Featuring the ultra-efficient full-range Class D topology, these compact amplifiers deliver serious power making them the best in class. Installation possibilities are endless due to its size and power amplification output. Even with its small platform, performance and sound quality are never sacrificed with Micro amplifiers from Diamond Audio! General Features: Ultra-compact, high-density aluminum alloy chassis provides superior thermal stability. Four-layer, glass epoxy circuit board for enhanced performance and reliability Full Range Class D amplifier technology Bridgeable for high-power operation (CH1+CH2/CH3+CH4) Balanced differential inputs for superior noise rejection Input sensitivity from 200mV to 10V accepts Line (RCA) and Speaker level input Input selector switch (2 CH / 4 CH) Selectable auto-turn-on mode: Signal Sensing (VOX), 12V Remote (REM), and DC offset (DC) Fully variable, 12dB per octave, electronic crossovers Built-in BTR Port (MICRO-USB) to connect our optional Bluetooth receiver-controller Illuminated logo Specifications: RMS Power Rating: RMS Power (2Ω): 150W x 4 RMS Power (4Ω): 80W x 4 Bridged (mono 1Ω): N/A Bridged (mono 2Ω): N/A Bridged (mono 4Ω): 300W x 2 Topology: Full Range Class D Power Supply: Power Supply: Full PWM Power Supply Threshold: 10.0VDC - 17.0VDC Idle Current: (0.7A) Distortion: THD 4 (1KHx @ 4Ω): 0.5% S/N Ratio (A weighted @1W): -85dBA S/N Ratio (A weighted @FP): -101.1dBA Input Sensitivity: Low Input Level: 200mV - 10.0V High Input Level: N/A Input Impedance: Low Input Level: 20KΩ High Input Level: 20KΩ Output Stage: Output Impedance: 0.018Ω Damping Factor (50Hz@4Ω): >70 Bandwidth (-3dB): 10Hz - 35Hz Crossover (-12dB/Oct): Variable High-Pass: 40Hz - 400Hz Variable Low-Pass: 40Hz - 400Hz Variable Sun-Sonic: N/A Fuse Ratings: 40A Dimensions: 9.07” L x 4.0” W x 1.46” H ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Diamond Audio MICRO4V2 Micro Series 600W 4-Channel Class-D Car Audio Amplifier Elite sound quality and superior power in an ultra-compact chassis. The Diamond Audio Micro4v2 4-channel power amplifier sets the standard for high-end Harley-specific amplifiers. Featuring ultra-efficient full-range class D topology and ICAD circuit that provides superior overload protection, these compact amplifiers deliver huge power for their size. Its compact design has the juice to power your system and will save you a ton of space in your car or transport whatever you need. The sound quality in a small footprint chassis can be found with Diamond Audio’s Micro series amplifiers. Featuring the ultra-efficient full-range Class D topology, these compact amplifiers deliver serious power making them the best in class. Installation possibilities are endless due to its size and power amplification output. Even with its small platform, performance and sound quality are never sacrificed with Micro amplifiers from Diamond Audio! General Features: Ultra-compact, high-density aluminum alloy chassis provides superior thermal stability. Four-layer, glass epoxy circuit board for enhanced performance and reliability Full Range Class D amplifier technology Bridgeable for high-power operation (CH1+CH2/CH3+CH4) Balanced differential inputs for superior noise rejection Input sensitivity from 200mV to 10V accepts Line (RCA) and Speaker level input Input selector switch (2 CH / 4 CH) Selectable auto-turn-on mode: Signal Sensing (VOX), 12V Remote (REM), and DC offset (DC) Fully variable, 12dB per octave, electronic crossovers Built-in BTR Port (MICRO-USB) to connect our optional Bluetooth receiver-controller Illuminated logo Specifications: RMS Power Rating: RMS Power (2Ω): 150W x 4 RMS Power (4Ω): 80W x 4 Bridged (mono 1Ω): N/A Bridged (mono 2Ω): N/A Bridged (mono 4Ω): 300W x 2 Topology: Full Range Class D Power Supply: Power Supply: Full PWM Power Supply Threshold: 10.0VDC - 17.0VDC Idle Current: (0.7A) Distortion: THD 4 (1KHx @ 4Ω): 0.5% S/N Ratio (A weighted @1W): -85dBA S/N Ratio (A weighted @FP): -101.1dBA Input Sensitivity: Low Input Level: 200mV - 10.0V High Input Level: N/A Input Impedance: Low Input Level: 20KΩ High Input Level: 20KΩ Output Stage: Output Impedance: 0.018Ω Damping Factor (50Hz@4Ω): >70 Bandwidth (-3dB): 10Hz - 35Hz Crossover (-12dB/Oct): Variable High-Pass: 40Hz - 400Hz Variable Low-Pass: 40Hz - 400Hz Variable Sun-Sonic: N/A Fuse Ratings: 40A Dimensions: 9.07” L x 4.0” W x 1.46” H ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.