Alpine (1200)

Alpine S2-A36F 600W Next Generation S-Series Hi Res Class-D 4-Channel Car Amplifier + Alpine RUX-H01 Halo Bass Knob Remote Bass Level Control The next generation of Alpine S-Series amplifiers is designed to take your car audio experience to the next level without breaking the bank. With a sleek new redesign and upgraded features from their predecessors, these amplifiers offer exceptional performance and power on an affordable budget.The S-Series S2-A36F 4-channel amplifier delivers 60 Watts RMS @4 Ohms or 90 Watts RMS @2 Ohms of pristine high-fidelity signal to your car's front and rear speakers, adding sweet, clear sound to your vehicle.The amp brings your music to life by being Hi-Res Audio certified, with its precise details and emotional power revealed with a frequency response up to 40kHz. For a 3-channel 2-way system, you could also use the amp to drive a pair of front speakers with 60 Watts RMS each while powering a subwoofer with 180 Watts RMS from the bridged rear channels. A variable mid-bass boost on those rear channels allows you to dial in some extra kick and impact to your system's low-frequency sound. You can even add the optional wired remote RUX-KNOB2 to control the level of the rear channels from your front seat.High- and low-pass filters put you in command of the frequency spectrum that reaches your speakers and subs. The amp includes preamp- and speaker-level inputs so you can install it in almost any vehicle, even with a factory radio. When using the speaker-level inputs, the amp can sense the incoming signal and turn itself on, eliminating the need to run a separate turn-on wire to the receiver or fuse box. General Features: Hi-Res Audio Certified (Up to 40kHz) Power Rating: 14.4V, < 0.3% THD +N Power Output: 60W RMS x 4 @ 4Ω, 90W RMS x 4 @ 2Ω Bridged Power: 180W RMS x 2 @ 4Ω 4-Channel Amplifier Alpine’s Class D Amplifier Circuit Two-sided terminal layout Built-in Selectable/ Adjustable Crossovers Mid-Bass EQ Input for more power Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately) Dimensions: 8.7” W x 2.25” H x 8.25” D Weight: 4 lbs, 13 oz S/N Ratio: >83dB Frequency Response: 20Hz – 40kHz Damping Factor: >100 Owner’s Manual 4 Self-tapping screws Hexagon wrench What is in the S2-A36F package: S2-A36F owner's manual 4-Channel amplifier 2 End caps Four 3/4" screws Four 1/4" screws 2mm Allen key Owner's manual Alpine Verification Certificate Warranty information Power supply note Online product registration information Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-A36F 600W Next Generation S-Series Hi Res Class-D 4-Channel Car Amplifier + Alpine RUX-KNOB.2 Remote Bass Level Control The next generation of Alpine S-Series amplifiers is designed to take your car audio experience to the next level without breaking the bank. With a sleek new redesign and upgraded features from their predecessors, these amplifiers offer exceptional performance and power on an affordable budget.The S-Series S2-A36F 4-channel amplifier delivers 60 Watts RMS @4 Ohms or 90 Watts RMS @2 Ohms of pristine high-fidelity signal to your car's front and rear speakers, adding sweet, clear sound to your vehicle.The amp brings your music to life by being Hi-Res Audio certified, with its precise details and emotional power revealed with a frequency response up to 40kHz. For a 3-channel 2-way system, you could also use the amp to drive a pair of front speakers with 60 Watts RMS each while powering a subwoofer with 180 Watts RMS from the bridged rear channels. A variable mid-bass boost on those rear channels allows you to dial in some extra kick and impact to your system's low-frequency sound. You can even add the optional wired remote RUX-KNOB2 to control the level of the rear channels from your front seat.High- and low-pass filters put you in command of the frequency spectrum that reaches your speakers and subs. The amp includes preamp- and speaker-level inputs so you can install it in almost any vehicle, even with a factory radio. When using the speaker-level inputs, the amp can sense the incoming signal and turn itself on, eliminating the need to run a separate turn-on wire to the receiver or fuse box. General Features: Hi-Res Audio Certified (Up to 40kHz) Power Rating: 14.4V, < 0.3% THD +N Power Output: 60W RMS x 4 @ 4Ω, 90W RMS x 4 @ 2Ω Bridged Power: 180W RMS x 2 @ 4Ω 4-Channel Amplifier Alpine’s Class D Amplifier Circuit Two-sided terminal layout Built-in Selectable/ Adjustable Crossovers Mid-Bass EQ Input for more power Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately) Dimensions: 8.7” W x 2.25” H x 8.25” D Weight: 4 lbs, 13 oz S/N Ratio: >83dB Frequency Response: 20Hz – 40kHz Damping Factor: >100 Owner’s Manual 4 Self-tapping screws Hexagon wrench What is in the S2-A36F package: S2-A36F owner's manual 4-Channel amplifier 2 End caps Four 3/4" screws Four 1/4" screws 2mm Allen key Owner's manual Alpine Verification Certificate Warranty information Power supply note Online product registration information Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-A55V S-Series Next Gen High-Resolution 5-Channel Car Audio Amplifier Alpine introduces the all-new S-Series amplifiers - a perfect match for the speakers. These amps have an excellent Watts-per-Euro ratio in the Class-D category, feature a very high heat resistance, and won’t shut down due to overheating. They also feature excellent sound quality in their price range. General Features: Class D 2 ohms Stable 5-Channel Amplifier RMS Power Rating: 4 ohms: 40 watts x 4 channel + 200 watts x 1 channel RMS Power Rating: 2 ohms: 60 watts x 4 channel + 300 watts x 1 channel Bridged: 120 watts x 2 channel @ 4 ohms + 300 watts x 1 channel @ 2 ohms Total power output: 540 watts CEA-2006 Compliant Amplifier LED Power/Protect Light Includes preamp- and speaker-level (high-level) inputs Wired remote bass level control included 3-way protection circuitry (thermal, overload, and speaker short protection) Frequency Response: 10 - 30,000 Hz Total Harmonic Distortion (THD): 1% Signal Noise Ratio: 83 dB Variable Bass Boost: 0 - 12 dB bass boost at 50 Hz Fuse Rating: 60A Enhanced Shutdown Performance technology 4 AWG gauge power and ground wiring are recommended for installation. Dimensions: 13-1/4" W x 8-1/16" L x 2-5/16" H Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the S2-A55V package: S2-A55V owner's manual 5-Channel amplifier Two 30-amp ATO fuses 2 End caps Four 3/4" Screws Four 1/4" screws 2mm Allen key Owner's manual Alpine Verification Certificate Warranty information Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-A55V S-Series Next Gen High-Resolution 5-Channel Car Audio Amplifier & RUX-H01 Remote Bass Knob Bundle Alpine introduces the all-new S-Series amplifiers - a perfect match for the speakers. These amps have an excellent Watts-per-Euro ratio in the Class-D category, feature a very high heat resistance, and won’t shut down due to overheating. They also feature excellent sound quality in their price range. General Features: Class D 2 ohms Stable 5-Channel Amplifier RMS Power Rating: 4 ohms: 40 watts x 4 channel + 200 watts x 1 channel RMS Power Rating: 2 ohms: 60 watts x 4 channel + 300 watts x 1 channel Bridged: 120 watts x 2 channel @ 4 ohms + 300 watts x 1 channel @ 2 ohms Total power output: 540 watts CEA-2006 Compliant Amplifier LED Power/Protect Light Includes preamp- and speaker-level (high-level) inputs Wired remote bass level control included 3-way protection circuitry (thermal, overload, and speaker short protection) Frequency Response: 10 - 30,000 Hz Total Harmonic Distortion (THD): 1% Signal Noise Ratio: 83 dB Variable Bass Boost: 0 - 12 dB bass boost at 50 Hz Fuse Rating: 60A Enhanced Shutdown Performance technology 4 AWG gauge power and ground wiring are recommended for installation. Dimensions: 13-1/4" W x 8-1/16" L x 2-5/16" H Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the S2-A55V package: S2-A55V owner's manual 5-Channel amplifier Two 30-amp ATO fuses 2 End caps Four 3/4" Screws Four 1/4" screws 2mm Allen key Owner's manual Alpine Verification Certificate Warranty information Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-A55V S-Series Next Gen High-Resolution 5-Channel Car Audio Amplifier & RUX-KNOB.2 Remote Bass Knob Bundle Alpine introduces the all-new S-Series amplifiers - a perfect match for the speakers. These amps have an excellent Watts-per-Euro ratio in the Class-D category, feature a very high heat resistance, and won’t shut down due to overheating. They also feature excellent sound quality in their price range. General Features: Class D 2 ohms Stable 5-Channel Amplifier RMS Power Rating: 4 ohms: 40 watts x 4 channel + 200 watts x 1 channel RMS Power Rating: 2 ohms: 60 watts x 4 channel + 300 watts x 1 channel Bridged: 120 watts x 2 channel @ 4 ohms + 300 watts x 1 channel @ 2 ohms Total power output: 540 watts CEA-2006 Compliant Amplifier LED Power/Protect Light Includes preamp- and speaker-level (high-level) inputs Wired remote bass level control included 3-way protection circuitry (thermal, overload, and speaker short protection) Frequency Response: 10 - 30,000 Hz Total Harmonic Distortion (THD): 1% Signal Noise Ratio: 83 dB Variable Bass Boost: 0 - 12 dB bass boost at 50 Hz Fuse Rating: 60A Enhanced Shutdown Performance technology 4 AWG gauge power and ground wiring are recommended for installation. Dimensions: 13-1/4" W x 8-1/16" L x 2-5/16" H Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the S2-A55V package: S2-A55V owner's manual 5-Channel amplifier Two 30-amp ATO fuses 2 End caps Four 3/4" Screws Four 1/4" screws 2mm Allen key Owner's manual Alpine Verification Certificate Warranty information Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-A55V S-Series Next Gen High-Resolution 5-Channel Car Audio Amplifier + Ansolute KIT0 0 Gauge AMP Kit Alpine introduces the all-new S-Series amplifiers - a perfect match to the S-Series speakers. These amps have an excellent Watts-per-Euro ratio in the Class-D category, feature a very high heat resistance, and won’t shut down due to overheating. They also feature excellent sound quality in their price range. General Features: Class D 2 ohms Stable 5-Channel Amplifier RMS Power Rating: 4 ohms: 40 watts x 4 channel + 200 watts x 1 channel RMS Power Rating: 2 ohms: 60 watts x 4 channel + 300 watts x 1 channel Bridged: 120 watts x 2 channel @ 4 ohms + 300 watts x 1 channel @ 2 ohms Total power output: 540 watts CEA-2006 Compliant Amplifier LED Power/Protect Light Includes preamp- and speaker-level (high-level) inputs Wired remote bass level control included 3-way protection circuitry (thermal, overload, and speaker short protection) Frequency Response: 10 - 30,000 Hz Total Harmonic Distortion (THD): 1% Signal Noise Ratio: 83 dB Variable Bass Boost: 0 - 12 dB bass boost at 50 Hz Fuse Rating: 60A Enhanced Shutdown Performance technology 4 AWG gauge power and ground wiring is recommended for installation. Dimensions: 13-1/4" W x 8-1/16" L x 2-5/16" H Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the S2-A55V package: S2-A55V owner's manual 5-Channel amplifier Two 30-amp ATO fuses 2 End caps Four 3/4" Screws Four 1/4" screws 2mm Allen key Owner's manual Alpine Verification Certificate Warranty information Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-A55V S-Series Next Gen High-Resolution 5-Channel Car Audio Amplifier + Ansolute KIT4 4 Gauge AMP Kit Alpine introduces the all-new S-Series amplifiers - a perfect match to the S-Series speakers. These amps have an excellent Watts-per-Euro ratio in the Class-D category, feature a very high heat resistance, and won’t shut down due to overheating. They also feature excellent sound quality in their price range. General Features: Class D 2 ohms Stable 5-Channel Amplifier RMS Power Rating: 4 ohms: 40 watts x 4 channel + 200 watts x 1 channel RMS Power Rating: 2 ohms: 60 watts x 4 channel + 300 watts x 1 channel Bridged: 120 watts x 2 channel @ 4 ohms + 300 watts x 1 channel @ 2 ohms Total power output: 540 watts CEA-2006 Compliant Amplifier LED Power/Protect Light Includes preamp- and speaker-level (high-level) inputs Wired remote bass level control included 3-way protection circuitry (thermal, overload, and speaker short protection) Frequency Response: 10 - 30,000 Hz Total Harmonic Distortion (THD): 1% Signal Noise Ratio: 83 dB Variable Bass Boost: 0 - 12 dB bass boost at 50 Hz Fuse Rating: 60A Enhanced Shutdown Performance technology 4 AWG gauge power and ground wiring is recommended for installation. Dimensions: 13-1/4" W x 8-1/16" L x 2-5/16" H Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the S2-A55V package: S2-A55V owner's manual 5-Channel amplifier Two 30-amp ATO fuses 2 End caps Four 3/4" Screws Four 1/4" screws 2mm Allen key Owner's manual Alpine Verification Certificate Warranty information Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-A60M 1-Channel 600 Watts S-Series Monoblock Class-D Amplifier + Absolute KIT4 4 Gauge Complete Amplifier Kit Alpine S2-A60M S-Series Monoblock Class-D Amplifier 600W RMSThe Alpine S-Series Sound ComponentsThree new S-Series amplifiers join the S-Series family, known for reliable performance and value-oriented products. All three S-Series amps (mono, 4-channel, and 5-channel) contain technology currently implemented in R and X-Series models. The S-Series amps feature attractive prices and are designed to perform perfectly with the existing S-Series speakers.S-Series amplifiers are your sound system’s workhorse. With unmatched reliability and budget-friendly prices, these amplifiers are the better choice in performance value.General Features: Alpine S-Series Mono Power Amplifier - S2-A60M RMS Power Output: 400W x 1 @ 4 Ohms (14.4V < 1% THD+N) 600W x 1 @ 2 Ohms (14.4V < 1% THD+N) S/N ratio: >85dB (ref: 1W into 4 ohms), >105dB (ref: rated power into 4 ohms) Remote bass knob compatible (requires RUX-KNOB.2, sold separately) CTA-2006 compliant THD+N ≤ 0.03% (ref 1W info 4 ohm) Frequency Response: 10HZ-400Hz (+/- 3 dB) Damping Factor: > 1000 variable low-pass filter (50-400 Hz, 24 dB/octave) variable bass boost (0-12 dB at 50 Hz) Speaker-level inputs (Speaker Wire to RCA Adapter Required) Preamp Inputs Improved heat sink and protection circuit design that eliminates thermal shut-down for dependable music playback Remote Sensing automatic turn-on when using speaker-level inputs Approximate Weight: 11 lbs Fuse Rating: fuse rating: 30A x 2 Four gauge power and ground wiring are recommended for installation. Contact us for information regarding a discount on select from our website when purchased together with this amplifier. Dimensions: 8” W x 8” H x 2.25” D Authorized Dealer 1-year Manufacturer's Warranty What's in the S2-A60M package: S2-A60M owner's manual Mono subwoofer amplifier Two 30-amp ATO fuses (installed) Four 3/4" Screws 2mm Allen wrench Owner's manual Alpine Verification Certificate Online product registration information Absolute KIT4 Complete PRO Marine 4 Gauge 2000 Watts Amplifier Complete Installation Amp Kit Power Wiring with Red Accent Color Scheme Installing a car amplifier is already enough of a job without having to worry about where to find the correct wire and installation accessories. You might not know that some companies are playing some gimmicks, and you could get ripped off! Today, I would recommend KIT4 for all DIY and installers. This wiring kit has an easy-to-install AGU fuse holder and some perfect wiring. The positive and negative power wires are made with copper-coated aluminum (CCA) wiring to keep costs down but remain highly flexible and installer-friendly. The speaker wire kicks ass, and I was not expecting such a high-quality roll of speaker wire to be included. It feels and works great and is much better than the typical 18 AWG wire most kits would include. General Features: Complete 4 Gauge Amplifier Kit Designed specifically for car audio systems up to 1000 watts Premium power and ground wire provide optimal power transfer Includes 2-channel RCA interconnect cables for the audio signal connection from the receiver to the amplifier Terminals are gold-plated for excellent signal transfer For use in any car, truck, RV, or boat Authorized Internet Dealer 1-year Manufacturer's warranty Package Includes: 17 ft. of red 4 AWG high current power cable Three ft. of black 4 AWG ground cable 15 ft. of RCA triple shielded interconnect audio cable with built-in remote wire 20 ft. of 12 AWG OFC Speaker cable 20 ft. of 16 AWG remote turn-on wire Six ft. of split loom tubing 1 Gold-plated 80 AMP AGU fuse 1 4 AWG gold ring terminal 1 4 AWG water-resistant inline fuse holder 2 Ring terminals 2 Spade terminals (4 gauge) 5 Spade terminals (14-16 gauge) 3 Self-tapping screws 1 Rubber grommet 20 Black cable ties 2 Butt connectors (18-22 gauge) 1 Butt connector (4 gauge) Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-A60M 1-Channel 600 Watts S-Series Monoblock Class-D Amplifier + Absolute KIT4OR 4 Gauge Complete Amplifier Kit Alpine S2-A60M S-Series Monoblock Class-D Amplifier 600W RMSThe Alpine S-Series Sound ComponentsThree new S-Series amplifiers join the S-Series family, known for reliable performance and value-oriented products. All three S-Series amps (mono, 4-channel, and 5-channel) contain technology currently implemented in R and X-Series models. The S-Series amps feature attractive prices and are designed to perform perfectly with the existing S-Series speakers.S-Series amplifiers are your sound system’s workhorse. With unmatched reliability and budget-friendly prices, these amplifiers are the better choice in performance value.General Features: Alpine S-Series Mono Power Amplifier - S2-A60M RMS Power Output: 400W x 1 @ 4 Ohms (14.4V < 1% THD+N) 600W x 1 @ 2 Ohms (14.4V < 1% THD+N) S/N ratio: >85dB (ref: 1W into 4 ohms), >105dB (ref: rated power into 4 ohms) Remote bass knob compatible (requires RUX-KNOB.2, sold separately) CTA-2006 compliant THD+N ≤ 0.03% (ref 1W info 4 ohm) Frequency Response: 10HZ-400Hz (+/- 3 dB) Damping Factor: > 1000 variable low-pass filter (50-400 Hz, 24 dB/octave) variable bass boost (0-12 dB at 50 Hz) Speaker-level inputs (Speaker Wire to RCA Adapter Required) Preamp Inputs Improved heat sink and protection circuit design that eliminates thermal shut-down for dependable music playback Remote Sensing automatic turn-on when using speaker-level inputs Approximate Weight: 11 lbs Fuse Rating: fuse rating: 30A x 2 Four gauge power and ground wiring are recommended for installation. Contact us for information regarding a discount on select from our website when purchased together with this amplifier. Dimensions: 8” W x 8” H x 2.25” D Authorized Dealer 1-year Manufacturer's Warranty What's in the S2-A60M package: S2-A60M owner's manual Mono subwoofer amplifier Two 30-amp ATO fuses (installed) Four 3/4" Screws 2mm Allen wrench Owner's manual (English/ French/ Spanish) Alpine Verification Certificate Online product registration information Absolute KIT4OR Complete PRO Marine Auto Car RV 4 Gauge 2000 Watts Amplifier Complete Installation Amp Kit Power Wiring with Orange Accent Color Scheme Today, I would recommend KIT4 for all DIY and installers. This wiring kit has an easy-to-install AGU fuse holder and some perfect wiring. The positive and negative power wires are made with copper-coated aluminum (CCA) wiring to keep costs down but remain highly flexible and installer-friendly. The speaker wire kicks ass, and I was not expecting such a high-quality roll of speaker wire to be included. It feels and works great and is much better than the typical 18 AWG wire most kits would include. General Features: Complete 4 Gauge Amplifier Kit Designed specifically for car audio systems up to 1000 watts Premium power and ground wire provide optimal power transfer Includes 2-channel RCA interconnect cables for the audio signal connection from the receiver to the amplifier Terminals are gold-plated for excellent signal transfer For use in any car, truck, RV, or boat Authorized Internet Dealer 1-year Manufacturer's warranty Package Includes: 17 ft. of 4 AWG high current power cable Three ft. of 4 AWG ground cable 15 ft. of RCA triple shielded interconnect audio cable with built-in remote wire 20 ft. of 12 AWG OFC Speaker cable 20 ft. of 16 AWG remote turn-on wire Six ft. of split loom tubing 1 Gold-plated 80 AMP AGU fuse 1 4 AWG gold ring terminal 1 4 AWG water-resistant inline fuse holder 2 Ring terminals 2 Spade terminals (4 gauge) 5 Spade terminals (14-16 gauge) 3 Self-tapping screws 1 Rubber grommet 20 Black cable ties 2 Butt connectors (18-22 gauge) 1 Butt connector (4 gauge) Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-A60M 1-Channel 600 Watts S-Series Monoblock Class-D Amplifier + Absolute KIT4AGU 4 Gauge Complete Amplifier Kit Alpine S2-A60M S-Series Monoblock Class-D Amplifier 600W RMSThe Alpine S-Series Sound ComponentsThree new S-Series amplifiers join the S-Series family, known for reliable performance and value-oriented products. All three S-Series amps (mono, 4-channel, and 5-channel) contain technology currently implemented in R and X-Series models. The S-Series amps feature attractive prices and are designed to perform perfectly with the existing S-Series speakers.S-Series amplifiers are your sound system’s workhorse. With unmatched reliability and budget-friendly prices, these amplifiers are the better choice in performance value.General Features: Alpine S-Series Mono Power Amplifier - S2-A60M RMS Power Output: 400W x 1 @ 4 Ohms (14.4V < 1% THD+N) 600W x 1 @ 2 Ohms (14.4V < 1% THD+N) S/N ratio: >85dB (ref: 1W into 4 ohms), >105dB (ref: rated power into 4 ohms) Remote bass knob compatible (requires RUX-KNOB.2, sold separately) CTA-2006 compliant THD+N ≤ 0.03% (ref 1W info 4 ohm) Frequency Response: 10HZ-400Hz (+/- 3 dB) Damping Factor: > 1000 variable low-pass filter (50-400 Hz, 24 dB/octave) variable bass boost (0-12 dB at 50 Hz) Speaker-level inputs (Speaker Wire to RCA Adapter Required) Preamp Inputs Improved heat sink and protection circuit design that eliminates thermal shut-down for dependable music playback Remote Sensing automatic turn-on when using speaker-level inputs Approximate Weight: 11 lbs Fuse Rating: fuse rating: 30A x 2 Four gauge power and ground wiring are recommended for installation. Contact us for information regarding a discount on select from our website when purchased together with this amplifier. Dimensions: 8” W x 8” H x 2.25” D Authorized Dealer 1-year Manufacturer's Warranty What's in the S2-A60M package: S2-A60M owner's manual Mono subwoofer amplifier Two 30-amp ATO fuses (installed) Four 3/4" Screws 2mm Allen wrench Owner's manual Alpine Verification Certificate Online product registration information Absolute KIT4AGU Complete PRO Marine Auto Car RV 4 Gauge 2000 Watts Amplifier Complete Installation Amp Kit Power Wiring with Red Accent Color Scheme Installing a car amplifier is already enough of a job without having to worry about where to find the correct wire and installation accessories. You might not know that some companies are playing some gimmicks, and you could get ripped off! Today, I would recommend KIT4 for all DIY and installers. This wiring kit has an easy-to-install AGU fuse holder and some perfect wiring. The positive and negative power wires are made with copper-coated aluminum (CCA) wiring to keep costs down but remain highly flexible and installer-friendly. The speaker wire kicks ass, and I was not expecting such a high-quality roll of speaker wire to be included. It feels and works great and is much better than the typical 18 AWG wire most kits would include. General Features: Complete 4 Gauge Amplifier Kit Designed specifically for car audio systems up to 1000 watts Premium power and ground wire provide optimal power transfer Includes 2-channel RCA interconnect cables for the audio signal connection from the receiver to the amplifier Terminals are gold-plated for excellent signal transfer For use in any car, truck, RV, or boat Authorized Internet Dealer 1-year Manufacturer's warranty Package Includes: 17 ft. of 4 AWG high current power cable Three ft. of 4 AWG ground cable 15 ft. of RCA triple shielded interconnect audio cable with built-in remote wire 20 ft. of 12 AWG OFC Speaker cable 20 ft. of 16 AWG remote turn-on wire Six ft. of split loom tubing 1 Gold-plated 80 AMP AGU fuse 1 4 AWG gold ring terminal 1 4 AWG water-resistant inline fuse holder 2 Ring terminals 2 Spade terminals (4 gauge) 5 Spade terminals (14-16 gauge) 3 Self-tapping screws 1 Rubber grommet 20 Black cable ties 2 Butt connectors (18-22 gauge) 1 Butt connector (4 gauge) Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-A60M 1-Channel 600 Watts S-Series Monoblock Class-D Amplifier + Absolute KIT4ANL 4 Gauge Complete Amplifier Kit Alpine S2-A60M S-Series Monoblock Class-D Amplifier 600W RMSThe Alpine S-Series Sound ComponentsThree new S-Series amplifiers join the S-Series family, known for reliable performance and value-oriented products. All three S-Series amps (mono, 4-channel, and 5-channel) contain technology currently implemented in R and X-Series models. The S-Series amps feature attractive prices and are designed to perform perfectly with the existing S-Series speakers.S-Series amplifiers are your sound system’s workhorse. With unmatched reliability and budget-friendly prices, these amplifiers are the better choice in performance value.General Features: Alpine S-Series Mono Power Amplifier - S2-A60M RMS Power Output: 400W x 1 @ 4 Ohms (14.4V < 1% THD+N) 600W x 1 @ 2 Ohms (14.4V < 1% THD+N) S/N ratio: >85dB (ref: 1W into 4 ohms), >105dB (ref: rated power into 4 ohms) Remote bass knob compatible (requires RUX-KNOB.2, sold separately) CTA-2006 compliant THD+N ≤ 0.03% (ref 1W info 4 ohm) Frequency Response: 10HZ-400Hz (+/- 3 dB) Damping Factor: > 1000 variable low-pass filter (50-400 Hz, 24 dB/octave) variable bass boost (0-12 dB at 50 Hz) Speaker-level inputs (Speaker Wire to RCA Adapter Required) Preamp Inputs Improved heat sink and protection circuit design that eliminates thermal shut-down for dependable music playback Remote Sensing automatic turn-on when using speaker-level inputs Approximate Weight: 11 lbs Fuse Rating: fuse rating: 30A x 2 Four gauge power and ground wiring are recommended for installation. Contact us for information regarding a discount on select from our website when purchased together with this amplifier. Dimensions: 8” W x 8” H x 2.25” D Authorized Dealer 1-year Manufacturer's Warranty What's in the S2-A60M package: S2-A60M owner's manual Mono subwoofer amplifier Two 30-amp ATO fuses (installed) Four 3/4" Screws 2mm Allen wrench Owner's manual Alpine Verification Certificate Online product registration information Absolute KIT4ANL Complete PRO Marine Auto Car RV 4 Gauge 2000 Watts ANL Amplifier Complete Installation Amp Kit Power Wiring with Red Accent Color Scheme Installing a car amplifier is already enough of a job without having to worry about where to find the right wire and installation accessories. You might not know that some companies are playing some gimmicks, and you could get ripped off! Today, I would recommend KIT4ANL for all DIY and installers. This wiring kit has an easy-to-install AGU fuse holder and some perfect wiring. The positive and negative power wires are made with copper-coated aluminum (CCA) wiring to keep costs down but remain highly flexible and installer-friendly. The speaker wire kicks ass, and I was not expecting such a high-quality roll of speaker wire to be included. It feels and works great and is much better than the typical 18 AWG wire most kits would include. General Features: Complete 4 Gauge Amplifier Kit Designed specifically for car audio systems up to 1000 watts Premium power and ground wire provide optimal power transfer Includes 2-channel RCA interconnect cables for the audio signal connection from the receiver to the amplifier Terminals are gold-plated for excellent signal transfer For use in any car, truck, RV, or boat Authorized Internet Dealer 1-year Manufacturer's warranty Package Includes: 16 ft. of 4 AWG high current power cable Three ft. of 4 AWG ground cable 17 ft. of RCA triple shielded interconnect audio cable with built-in remote wire 20 ft. of 12 AWG OFC Speaker cable 20 ft. of 16 AWG remote turn-on wire Six ft. of split loom tubing 1 Gold-plated 80 AMP AGU fuse 1 4 AWG gold ring terminal 1 ANL 4 AWG water-resistant inline fuse holder 1 PCS 100 AMP ANL Fuse 2 Ring terminals 2 Spade terminals (4 gauge) 5 Spade terminals (14-16 gauge) 3 Self-tapping screws 1 Rubber grommet 20 Black cable ties 2 Butt connectors (18-22 gauge) 1 Butt connector (4 gauge) Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-A60M 1-Channel 600 Watts S-Series Monoblock Class-D Amplifier + Absolute KIT4OR 4 Gauge Complete Amplifier Kit Package Includes: 1 Alpine S2-A60M, 1 Absolute KIT4 Amplifier Kit 4 Gauge Alpine S2-A60M 1-Channel 600 Watts S-Series Monoblock Class-D Amplifier General Features: Alpine S-Series Mono Power Amplifier - S2-A60M 400W x 1 @ 4 Ohms RMS Power Output 600W x 1 @ 2 Ohms RMS Power Output S/N ratio: >85dB (ref: 1W into 4 ohms), >105dB (ref: rated power into 4 ohms) Remote bass knob compatible (requires RUX-KNOB.2, sold separately) CTA-2006 compliant THD+N ≤ 0.03% (ref 1W info 4 ohm) Frequency Response: 10HZ-400Hz (+/- 3 dB) Damping Factor: > 1000 variable low-pass filter (50-400 Hz, 24 dB/octave) variable bass boost (0-12 dB at 50 Hz) Speaker-level inputs (Speaker Wire to RCA Adapter Required) Preamp Inputs Improved heat sink and protection circuit design that eliminates thermal shut-down for dependable music playback Remote Sensing automatic turn-on when using speaker-level inputs Approximate Weight: 11 lbs Fuse Rating: fuse rating: 30A x 2 Dimensions: 8” W x 8” H x 2.25” D Authorized Internet Dealer 1-year Manufacturer's Warranty Absolute KIT4OR Complete PRO Marine Auto Car RV 4 Gauge 2000 Watts Amplifier Complete Installation Amp Kit Power Wiring with Orange Accent Color Scheme Today, I would recommend KIT4 for all DIY and installers. This wiring kit has an easy-to-install AGU fuse holder and some perfect wiring. The positive and negative power wires are made with copper-coated aluminum (CCA) wiring to keep costs down but remain highly flexible and installer-friendly. The speaker wire kicks ass, and I was not expecting such a high-quality roll of speaker wire to be included. It feels and works great and is much better than the typical 18 AWG wire most kits would include. General Features: Complete 4 Gauge Amplifier Kit Designed specifically for car audio systems up to 1000 watts Premium power and ground wire provide optimal power transfer Includes 2-channel RCA interconnect cables for the audio signal connection from the receiver to the amplifier Terminals are gold-plated for excellent signal transfer For use in any car, truck, RV, or boat Authorized Internet Dealer 1-year Manufacturer's warranty Package Includes: 17 ft. of 4 AWG high current power cable Three ft. of 4 AWG ground cable 15 ft. of RCA triple shielded interconnect audio cable with built-in remote wire 20 ft. of 12 AWG OFC Speaker cable 20 ft. of 16 AWG remote turn-on wire Six ft. of split loom tubing 1 Gold-plated 80 AMP AGU fuse 1 4 AWG gold ring terminal 1 4 AWG water-resistant inline fuse holder 2 Ring terminals 2 Spade terminals (4 gauge) 5 Spade terminals (14-16 gauge) 3 Self-tapping screws 1 Rubber grommet 20 Black cable ties 2 Butt connectors (18-22 gauge) 1 Butt connector (4 gauge) Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.