Alpine (1197)

Alpine S-W12D4 1800W Max (600W RMS) 12" Type-S Series Dual 4 Ohm Car Subwoofer VERSATILE APPLICATIONS Along with the new 8” woofer, the 10” and 12” S-Series subwoofers have been re-designed from the ground up. The mounting depth of the 10” and 12” subwoofers are almost 1” more shallow than previous models at just over 4.5” for the 10” models and just over 5” for the 12” models, allowing them to fit into a wide variety of installation applications. General Features: 12" 4 Ohm Type-S Series Subwoofer Power Handling: Peak: 1800 watts RMS: 600 watts Recommended power range: 250- 600W RMS Pulp/Kevlar Cone High Amplitude Multi-Roll (HAMR) Surround Progressive Spider with Reinforced Layer Tinsel Leads Airflow Optimized Dual Flare Pole Vent High Strength Steel Frame Basket 8 AWG Push Terminals with VC Configuration Jumpers Dual Voice Coil High-Grade Strontium Ferrite Magnets Top-mount depth: 5-1/16" Cutout diameter: 10-9" Frequency Response: 26- 200Hz Sensitivity: 86.4dB Resonance Frequency (Fs): 31 Hz Authorized Dealer 1-year Manufacturer's Warranty What is in the S-W12D4 package: Alpine S-W12D4 owners manual One 12" Dual 4-ohm voice coil subwoofer Two 3" jumper cables Subwoofer Application Guide Online product registration information Warranty Information ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine S-W8D2 900W Max (300W RMS) 8" S-Series Dual 2 Ohm Car Subwoofers ADD BASS TO PRACTICALLY ANY VEHICLE Don’t think you have room for a subwoofer? Think again. The new S-W8D2 and S-W8D4 8” S-Series subwoofers have a shallow mounting depth of just 3-3/4” and can be used in a sealed box enclosure as small as .15 cubic foot. It is perfect for under-seats, behind rear bench seats in trucks, or even in some door applications.  General Features: 8" 2 Ohm S-Series Subwoofer Power Handling: Peak: 900 watts RMS: 300 watts Recommended power range: 150 - 300 RMS Kevlar Reinforced Pulp Cone HAMR Santoprene Rubber Surround High Strength Steel Frame Basket Concealed Mount Gasket High Strength Steel Frame Basket 10 AWG Push Terminals High Excursion Underhung Voice Coil Configuration High-Grade Strontium Ferrite Magnet Top-mount depth: 3-3/4" Cutout diameter: 6-7/8" Frequency Response: 34 - 200 Hz Sensitivity: 83dB Resonance Frequency (Fs): 48 Hz Authorized Dealer 1-year Manufacturer's Warranty What's in the S-W8D2 package: 8" Dual 2-ohm voice coil subwoofer Alpine S-W8D2 owner's manual 1 Rubber concealing ring Two 3" jumper cables Subwoofer Application Guide Online product registration information Warranty information  Important Notice!  ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine S-W8D4 900W Max (300W RMS) 8" Type S Series Dual 4 Ohm Car Subwoofer ADD BASS TO PRACTICALLY ANY VEHICLE Don’t think you have room for a subwoofer? Think again. The new S-W8D2 and S-W8D4 8” S-Series subwoofers have a shallow mounting depth of just 3-3/4” and can be used in a sealed box enclosure as small as .15 cubic feet. It is perfect for under-seats, behind rear bench seats in trucks, or even in some door applications. General Features: 8" 4 Ohm Type S Series Subwoofer Power Handling: Peak: 900 watts RMS: 300 watts Recommended Power Range: 150 - 300 Watts Kevlar Reinforced Pulp Cone HAMR Santoprene Rubber Surround Progressive Spider with Reinforced Layer Tinsel Leads Compound Radius Curve Extended Pole Geometry Perimeter Vented Frame with Airflow Management System 10 AWG Push Terminals 35mm Underhung Voice Coils Concealed Mount Gasket 34oz Ferrite Magnet Top-mount depth: 3-3/4" Cutout diameter: 6-7/8" Frequency Response: 34-200Hz Authorized Dealer 1-year Manufacturer's Warranty Priced Individually What's in the S-W8D4 package: 8" Dual 4-ohm voice coil subwoofer Alpine S-W8D4 owner's manual 1 Rubber concealing ring Two 3" jumper cables Subwoofer Application Guide Online product registration information Warranty information  Important Notice!  ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Alpine S2-A36F 600W Next Generation S-Series Hi Res Class-D 4-Channel Car Amplifier The next generation of Alpine S-Series amplifiers is designed to enhance your car audio experience without breaking the bank. With a sleek new redesign and upgraded features from their predecessors, these amplifiers offer exceptional performance and power on an affordable budget.The S-Series S2-A36F 4-channel amplifier delivers 60 Watts RMS @4 Ohms or 90 Watts RMS @2 Ohms of pristine high-fidelity signal to your car's front and rear speakers, adding sweet, clear sound to your vehicle.The amp brings your music to life by being Hi-Res Audio certified, with its precise details and emotional power revealed with a frequency response up to 40kHz. For a 3-channel 2-way system, you could also use the amp to drive a pair of front speakers with 60 Watts RMS each while powering a subwoofer with 180 Watts RMS from the bridged rear channels. A variable mid-bass boost on those rear channels allows you to dial in some extra kick and impact to your system's low-frequency sound. You can even add the optional wired remote RUX-KNOB2 to control the level of the rear channels from your front seat.High- and low-pass filters put you in command of the frequency spectrum that reaches your speakers and subs. The amp includes preamp- and speaker-level inputs so that you can install it in almost any vehicle, even with a factory radio. When using the speaker-level inputs, the amp can sense the incoming signal and turn itself on, eliminating the need to run a separate turn-on wire to the receiver or fuse box. General Features: Hi-Res Audio Certified (Up to 40kHz) Power Rating: 14.4V, < 0.3% THD +N Power Output: 60W RMS x 4 @ 4Ω, 90W RMS x 4 @ 2Ω Bridged Power: 180W RMS x 2 @ 4Ω 4-Channel Amplifier Alpine’s Class D Amplifier Circuit Two-sided terminal layout Built-in Selectable/ Adjustable Crossovers Mid-Bass EQ Input for more power Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately) Dimensions: 8.7” W x 2.25” H x 8.25” D Weight: 4 lbs, 13 oz S/N Ratio: >83dB Frequency Response: 20Hz – 40kHz Damping Factor: >100 Owner’s Manual 4 Self-tapping screws Hexagon wrench What is in the S2-A36F package: S2-A36F owner's manual 4-Channel amplifier One 40-amp ATO fuse Four 3/4" Screws 2mm Allen wrench Alpine Verification Certificate Warranty information Online product registration information Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-A36F 4 Channel Amplifier, S-S69 6X9" Coax Speakers, S-S50 5.25" Coax Speakers and Absolute 8 Gauge Wiring Kit This bundle includes an Alpine S2-A36F 4-Channel V-Power Amplifier, an 8 Gauge Wiring Kit, a pair of Alpine S-Series S-S69 6x9" Coaxial Speakers, and a pair of Alpine S-S50 S-Series 5.25-inch Coaxial 2-Way Speakers. Alpine S2-A36F 600W Next Generation S-Series Hi Res Class-D 4-Channel Car Amplifier The next generation of Alpine S-Series amplifiers is designed to enhance your car audio experience without breaking the bank. With a sleek new redesign and upgraded features from their predecessors, these amplifiers offer exceptional performance and power on an affordable budget.The S-Series S2-A36F 4-channel amplifier delivers 60 Watts RMS @4 Ohms or 90 Watts RMS @2 Ohms of pristine high-fidelity signal to your car's front and rear speakers, adding sweet, clear sound to your vehicle. General Features: Hi-Res Audio Certified (Up to 40kHz) Power Rating: 14.4V, < 0.3% THD +N Power Output: 60W RMS x 4 @ 4Ω, 90W RMS x 4 @ 2Ω Bridged Power: 180W RMS x 2 @ 4Ω 4-Channel Amplifier Alpine’s Class D Amplifier Circuit Two-sided terminal layout Built-in Selectable/ Adjustable Crossovers Mid-Bass EQ Input for more power Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately) Dimensions: 8.7” W x 2.25” H x 8.25” D Weight: 4 lbs, 13 oz S/N Ratio: >83dB Frequency Response: 20Hz – 40kHz Damping Factor: >100 Owner’s Manual 4 Self-tapping screws Hexagon wrench Alpine S-S69 520W Max (170W RMS) 6" x 9" Type S Series 2-Way Coaxial Car Speakers General Features: 6" x 9" Type S Series 2-Way Coaxial Car Speakers Power Handling: Peak: 520 watts per pair / 260 watts each Power Handling: RMS: 170 watts per pair / 85 watts each Recommended Power Range: 10 - 85 watts RMS per channel Carbon Fiber Reinforced Plastic (CFRP) Cone High Amplitude Multi-Roll (HAMR) Surround 1" Silk Dome Tweeter Rubber magnet boot cover CEA-2031 compliant speakers 35mm Voice Coil Top-mount Depth: 2-15/16" Cutout Dimensions: 5-29/32" x 8-3/4" 4 ohms Impedance Frequency Response: 65 - 22000 Hz Sensitivity: 90dB Compatible with the Alpine KTE-S69G Grille Authorized Dealer 1-year Manufacturer's Warranty What is in the S-S69 package: S-S69 owner's manual Two 2-way speakers 2 Bottom mount brackets Two 12" Lengths of speaker wire Eight 1-3/16" Screws Eight M4x60mm Machine screws  Eight M4 Nuts Warranty information Online product registration information Alpine S-S50 340W Max (110W RMS) 5 1/4" Type S Series 2-Way Coaxial Car Speakers General Features: 5 1/4" S-Type Series TYPE Car Speakers/Component System Peak Power Handling: 340 watts per pair / 170 watts each RMS Power Handling: 110 watts per pair / 55 watts each Carbon fiber reinforced plastic cone Patented HAMR surround 3/4" Silk dome tweeter CTA-2031 compliant speakers 30MM Voice Coil Top-mount Depth: 2" 4 ohms impedance Frequency Response: 73 - 22000 Hz Sensitivity: 88dB Authorized Dealer 1-year Manufacturer's Warranty What's in the S-S50 package: S-S50 owner's manual Two 2-way speakers 2 Adapter rings Two 12" Lengths of speaker wire Eight 1-1/4" Screws Eight M4x6mm Machine screws Warranty information Online product registration information Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-A36F 4 Channel Amplifier +2 Pair S-S57 5X7/6X8 Coax Speakers + Absolute KIT4 4 Gauge Wiring Kit This bundle includes an Alpine S2-A36F 4-Channel V-Power Amplifier, a 4 Gauge Wiring Kit, and two pairs of Alpine S-Series -S57 5X7/6X8 Coaxial Speakers. Alpine S2-A36F 600W Next Generation S-Series Hi-Res Class-D 4-Channel Car Amplifier The next generation of Alpine S-Series amplifiers is designed to enhance your car audio experience without breaking the bank. With a sleek new redesign and upgraded features from their predecessors, these amplifiers offer exceptional performance and power on an affordable budget. General Features: Hi-Res Audio Certified (Up to 40kHz) Power Rating: 14.4V, < 0.3% THD +N Power Output: 60W RMS x 4 @ 4Ω, 90W RMS x 4 @ 2Ω Bridged Power: 180W RMS x 2 @ 4Ω 4-Channel Amplifier Alpine’s Class D Amplifier Circuit Two-sided terminal layout Built-in Selectable/ Adjustable Crossovers Mid-Bass EQ Input for more power Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately) Dimensions: 8.7” W x 2.25” H x 8.25” D Weight: 4 lbs, 13 oz S/N Ratio: >83dB Frequency Response: 20Hz – 40kHz Damping Factor: >100 Owner’s Manual 4 Self-tapping screws Hexagon wrench Alpine S2-S68 6x8" or 5x7" 460W Peak (150W RMS) 6x8" S-Series 2-way 4-ohm Coaxial Car Speakers Newly redesigned and Hi-Res Audio Certified, the Next-Generation S-Series S2-S68 6x8” Coaxial Speakers offer a new standard in entry-level sound performance. Using “trickle-down” technology, inspired design, and performance cues from the Ultra-High-Resolution AlpineF#1Status system, the Next-Generation Alpine S-Series Speakers are now Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This new benchmark in sound quality elevates the Next-Gen S-Series Speakers, resulting in a more accurate and natural sound at an entry-level price point.  General Features: 6" x 8" S Series 2-way Coaxial Car Speakers Peak Power Handling: 460 watts per pair / 230 watts each RMS Power Handling: 150 watts per pair / 75 watts each Hi-Res Audio certified Combined Polypropylene, Glass Fiber, and Mica cone material High-Amplitude Multi-Roll (HAMR) speaker surround 1" Cloth Dome tweeters 3.54" magnet and enhanced motor structure with 110% power handling Lightweight design with high output and low distortion Wide vehicle fitment range for easy installation Top-mount Depth: 2-3/8" Cutout Dimensions: 5 x 7-3/16  Impedance: 4 ohms Frequency Response: 75 - 40,000 Hz Sensitivity: 88 dB Authorized Internet Dealer 1-year Manufacturer's Warranty Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca. 

Alpine S2-A36F 4-Channel Car Amplifier, 50 Watts RMS x 4 + 2 Cerwin-Vega XED12V2 12" Subwoofers + Absolute 8G Amp Kit Alpine S2-A36F 600W Next Generation S-Series Hi Res Class-D 4-Channel Car Amplifier The next generation of Alpine S-Series amplifiers is designed to enhance your car audio experience without breaking the bank. With a sleek new redesign and upgraded features from their predecessors, these amplifiers offer exceptional performance and power on an affordable budget.The S-Series S2-A36F 4-channel amplifier delivers 60 Watts RMS @4 Ohms or 90 Watts RMS @2 Ohms of pristine high-fidelity signal to your car's front and rear speakers, adding sweet, clear sound to your vehicle.The amp brings your music to life by being Hi-Res Audio certified, with its precise details and emotional power revealed with a frequency response up to 40kHz. For a 3-channel 2-way system, you could also use the amp to drive a pair of front speakers with 60 Watts RMS each while powering a subwoofer with 180 Watts RMS from the bridged rear channels. A variable mid-bass boost on those rear channels allows you to dial in some extra kick and impact to your system's low-frequency sound. You can even add the optional wired remote RUX-KNOB2 to control the level of the rear channels from your front seat.High- and low-pass filters put you in command of the frequency spectrum that reaches your speakers and subs. The amp includes preamp- and speaker-level inputs so that you can install it in almost any vehicle, even with a factory radio. When using the speaker-level inputs, the amp can sense the incoming signal and turn itself on, eliminating the need to run a separate turn-on wire to the receiver or fuse box. General Features: Hi-Res Audio Certified (Up to 40kHz) Power Rating: 14.4V, < 0.3% THD +N Power Output: 60W RMS x 4 @ 4Ω, 90W RMS x 4 @ 2Ω Bridged Power: 180W RMS x 2 @ 4Ω 4-Channel Amplifier Alpine’s Class D Amplifier Circuit Two-sided terminal layout Built-in Selectable/ Adjustable Crossovers Mid-Bass EQ Input for more power Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately) Dimensions: 8.7” W x 2.25” H x 8.25” D Weight: 4 lbs, 13 oz S/N Ratio: >83dB Frequency Response: 20Hz – 40kHz Damping Factor: >100 Owner’s Manual 4 Self-tapping screws Hexagon wrench Cerwin Vega XED12V2 1000W Max 125W RMS 12" XED Series Single 4-Ohm Car Subwoofer Universal 12" XED Mobile Series 1000W 4-ohm SVC Subwoofer by Cerwin-Vega. Feel the bass with these premium quality subwoofers by Cerwin-Vega, designed and manufactured to deliver the decibels. Constructed from the highest quality materials with the utmost attention to every tiny detail, they will provide maximum performance for years to come. General Features: 12" Single 4-ohm Xtreme-Energy Design Subwoofer Parabolic Poly Cone Single Stitched High Roll Surround Vented Pole Piece/Basket for Cooler Voice Coil Temperatures Bumped Back Plate for Maximum Excursion Signature Cerwin-Vega Bass Peak Power Handling: 1000W RMS Power Handling: 150W Impedance: 4 Ohms Voice Coil: Single Voice Coil Size: 2" Mounting Diameter: 10.82" Mounting Depth: 5.25" Sensitivity: 85.5dB Authorized Internet Dealer 1-year Manufacturer's Warranty Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-A36F S-Series Class-D 4-Channel Car Amplifier & 2 Pairs Alpine S2-S80C - Next-Generation S-Series 8" Component Speaker Set 2 Pairs Alpine S2-S80C - Next-Generation S-Series 8" Component Speaker Set General Features: 8" 2-way component speaker system 8" polypropylene/glass-fiber/mica woofer cone with High-Amplitude Multi-Roll surround 1" silk dome tweeter with threaded removable housing In-line crossovers for easier installation frequency range: 50-40,000 Hz Peak Power Handling:  520 watts per set / 260 watts on each side RMS Power Handling: 170 watts per set / 85 watts on each side Rubber speaker surround High Amplitude Multi-Roll surround technology Ferrite magnet motor structure Impedance: 4 ohms Sensitivity: 80 dB Authorized Internet Dealer 1-year Manufacturer's Warranty Alpine S2-A36F 600W Next Generation S-Series Hi-Res Class-D 4-Channel Car Amplifier General Features: Hi-Res Audio Certified (Up to 40kHz) Power Rating: 14.4V, < 0.3% THD +N Power Output: 60W RMS x 4 @ 4Ω, 90W RMS x 4 @ 2Ω Bridged Power: 180W RMS x 2 @ 4Ω 4-Channel Amplifier Alpine’s Class D Amplifier Circuit Two-sided terminal layout Built-in Selectable/ Adjustable Crossovers Mid-Bass EQ Input for more power Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately) Dimensions: 8.7” W x 2.25” H x 8.25” D Weight: 4 lbs, 13 oz S/N Ratio: >83dB Frequency Response: 20Hz – 40kHz Damping Factor: >100 Owner’s Manual 4 Self-tapping screws Hexagon wrench Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca. 

Alpine S2-A36F S-Series Class-D 4-Channel Car Amplifier & Alpine S2-S80C - Next-Generation S-Series 8" Component Speaker Set Alpine S2-S80C - Next-Generation S-Series 8" Component Speaker Set General Features: 8" 2-way component speaker system 8" polypropylene/glass-fiber/mica woofer cone with High-Amplitude Multi-Roll surround 1" silk dome tweeter with threaded removable housing In-line crossovers for easier installation frequency range: 50-40,000 Hz Peak Power Handling:  520 watts per set / 260 watts on each side RMS Power Handling: 170 watts per set / 85 watts on each side Rubber speaker surround High Amplitude Multi-Roll surround technology Ferrite magnet motor structure Impedance: 4 ohms Sensitivity: 80 dB Authorized Internet Dealer 1-year Manufacturer's Warranty Alpine S2-A36F 600W Next Generation S-Series Hi-Res Class-D 4-Channel Car Amplifier General Features: Hi-Res Audio Certified (Up to 40kHz) Power Rating: 14.4V, < 0.3% THD +N Power Output: 60W RMS x 4 @ 4Ω, 90W RMS x 4 @ 2Ω Bridged Power: 180W RMS x 2 @ 4Ω 4-Channel Amplifier Alpine’s Class D Amplifier Circuit Two-sided terminal layout Built-in Selectable/ Adjustable Crossovers Mid-Bass EQ Input for more power Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately) Dimensions: 8.7” W x 2.25” H x 8.25” D Weight: 4 lbs, 13 oz S/N Ratio: >83dB Frequency Response: 20Hz – 40kHz Damping Factor: >100 Owner’s Manual 4 Self-tapping screws Hexagon wrench Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca. 

Alpine S2-A36F S-Series 320W RMS 4-Channel Digital Class D Car Audio Amplifier + Cerwin-Vega XED650C Component Speaker + Cerwin-Vega V465 6.5" Speaker + Absolute KIT8 Complete 8 Gauge Amplifier Wiring Kit Alpine S2-A36F S-Series 320W RMS 4-Channel Digital Class D Car Audio Amplifier The all-new S-Series amplifiers pack a punch with even more performance and value. The S2-A36F 4-channel amplifier offers hard-hitting bass and long hours of limitless play. These amplifiers offer great value with over 20% more power through increased watt handling. They support exceptional strength and resistance by optimizing a heat thermal management processor to ensure exceptional reliability. You can enjoy your music with the bass cranked up for hours without any power shutdown.General Features: Alpine S2-Series S2-A36F 4/3/2 Channel Power Amplifier S-Series amplifiers are your sound system’s workhorse. With unmatched reliability and budget-friendly prices, these amplifiers are the better choice regarding performance value. S-Series Amplifier: Known for reliable performance and value-oriented products. Power Output: 55W RMS x 4 (4ohm, 14.4V ≤ 1% THD+N) 80W RMS x 4 (2ohm, 14.4V≤ 1% THD+N) Bridged: 160W RMS x 2 (4ohm, 14.4V ≤ 1% THD+N) Total power output: 320 watts CEA-2006 Compliant Amplifier LED Power/Protect Light Speaker-level (high-level) inputs 3-way protection circuitry (thermal, overload, and short speaker protection) Frequency Response: 10 - 30,0000 Hz Total Harmonic Distortion (THD): <1% Signal Noise Ratio: 83 dB Variable high-pass filter: 50 - 400 Hz, 12 dB/octave Variable low-pass filter: 50 - 400 Hz, 12 dB/octave Fuse Rating: 40 Improved heat sink and protection circuit design Contains technology currently implemented in the Alpine R and X-Series models 105dB Signal-to-Noise (S/N) ratio at rated power 46 degrees of phase shift Designed to perform perfectly with the existing S-Series speakers and subwoofers Dimensions: 8” W x 8” H x 2.25” D Authorized Dealer 1-year Manufacturer's Warranty What is in the S2-A36F package: S2-A36F owner's manual 4-Channel amplifier One 40-amp ATO fuse Four 3/4" Screws 2mm Allen wrench Alpine Verification Certificate Warranty information Online product registration information Cerwin-Vega XED650C 600W 6.5" 2-Way Component Power Handling Speaker Experience the clear, vibrant sound and hear aspects of songs you probably weren't aware of with premium-quality products by Carwin-Vega designed and manufactured to make you hear the music and 'feel' it. Made from premium-quality materials, every unit from this brand ensures nothing less than long-lasting performance while providing the best live concert experience. General Features: 6.5" XED Series 2-Way Component System Power Handling: Peak: 300 watts RMS: 30 watts Curvilinear polypropylene cone Butyl rubber surround Linear woven treated red spider 1" balanced metal dome CV tweeter Frequency Response: 60-18,000 Hz Top-mount Depth: 2.2" Sensitivity: 93dB Authorized Internet Dealer 1-year Manufacturer's Warranty Cerwin-Vega V465 400W 6.5" 2-Way Vega Series Coaxial Speakers w/ Titanium Tweeters General Features: Peak Power Handling: 400 watts RMS Power Handling: 75 watts Mica-filled poly cone Vega's signature red surround 1" titanium dome tweeter Frequency Response: 55-20,000 Hz Top-mount Depth: 2.78" Sensitivity: 94dB Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-A36F 4-Channel Car Amplifier, 50 Watts RMS x 4 + Absolute 8 Gauge Amplifier Kit Alpine S2-A36F 600W Next Generation S-Series Hi Res Class-D 4-Channel Car Amplifier The next generation of Alpine S-Series amplifiers is designed to enhance your car audio experience without breaking the bank. With a sleek new redesign and upgraded features from their predecessors, these amplifiers offer exceptional performance and power on an affordable budget.The S-Series S2-A36F 4-channel amplifier delivers 60 Watts RMS @4 Ohms or 90 Watts RMS @2 Ohms of pristine high-fidelity signal to your car's front and rear speakers, adding sweet, clear sound to your vehicle.The amp brings your music to life by being Hi-Res Audio certified, with its precise details and emotional power revealed with a frequency response up to 40kHz. For a 3-channel 2-way system, you could also use the amp to drive a pair of front speakers with 60 Watts RMS each while powering a subwoofer with 180 Watts RMS from the bridged rear channels. A variable mid-bass boost on those rear channels allows you to dial in some extra kick and impact to your system's low-frequency sound. You can even add the optional wired remote RUX-KNOB2 to control the level of the rear channels from your front seat.High- and low-pass filters put you in command of the frequency spectrum that reaches your speakers and subs. The amp includes preamp- and speaker-level inputs so that you can install it in almost any vehicle, even with a factory radio. When using the speaker-level inputs, the amp can sense the incoming signal and turn itself on, eliminating the need to run a separate turn-on wire to the receiver or fuse box. General Features: Hi-Res Audio Certified (Up to 40kHz) Power Rating: 14.4V, < 0.3% THD +N Power Output: 60W RMS x 4 @ 4Ω, 90W RMS x 4 @ 2Ω Bridged Power: 180W RMS x 2 @ 4Ω 4-Channel Amplifier Alpine’s Class D Amplifier Circuit Two-sided terminal layout Built-in Selectable/ Adjustable Crossovers Mid-Bass EQ Input for more power Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately) Dimensions: 8.7” W x 2.25” H x 8.25” D Weight: 4 lbs, 13 oz S/N Ratio: >83dB Frequency Response: 20Hz – 40kHz Damping Factor: >100 Owner’s Manual 4 Self-tapping screws Hexagon wrench Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Alpine S2-A36F 4-Channel Amplifier w/ Pair of Alpine S2-S65C 6.5" Component Speakers Package + Absolute KIT8 Complete 8 Gauge Amplifier Wiring Kit Alpine S2-A36F 600W Next Generation S-Series Hi-Res Class-D 4-Channel Car Amplifier The next generation of Alpine S-Series amplifiers is designed to enhance your car audio experience without breaking the bank. With a sleek new redesign and upgraded features from their predecessors, these amplifiers offer exceptional performance and power on an affordable budget.The S-Series S2-A36F 4-channel amplifier delivers 60 Watts RMS @4 Ohms or 90 Watts RMS @2 Ohms of pristine high-fidelity signal to your car's front and rear speakers, adding sweet, clear sound to your vehicle. General Features: Hi-Res Audio Certified (Up to 40kHz) Power Rating: 14.4V, < 0.3% THD +N Power Output: 60W RMS x 4 @ 4Ω, 90W RMS x 4 @ 2Ω Bridged Power: 180W RMS x 2 @ 4Ω 4-Channel Amplifier Alpine’s Class D Amplifier Circuit Two-sided terminal layout Built-in Selectable/ Adjustable Crossovers Mid-Bass EQ Input for more power Optional Remote Bass Knob Compatible (required RUX-KNOB.2 or RUX-H01, sold separately) Dimensions: 8.7” W x 2.25” H x 8.25” D Weight: 4 lbs, 13 oz S/N Ratio: >83dB Frequency Response: 20Hz – 40kHz Damping Factor: >100 Owner’s Manual 4 Self-tapping screws Hexagon wrench Alpine S2-S65C 240W 6.5" Component Type-S 2-way speaker set with 1" Silk Tweeters General Features: 6-1/2" Type-S Series Car Speakers Peak Power Handling: 480 watts per pair / 240 watts each RMS Power Handling: 160 watts per pair / 80 watts each (CEA-2031 Certified) Tuned poly-mica cone woofer Butyl rubber surround for natural response and stability 1" Wide-Range Silk dome tweeter Optimized air-flow design Progressive Aramid Fiber Spider with optimized shape for deep bass and linearity HD Polymer frame FEA-optimized motor structure OEM mounting adapters included Swivel-mount tweeter 4 ohms impedance Square-wire short voice coil The new cone design allows for faster energy transfer & clarity Aramid-reinforced TIL bobbin holds voice coil wire very rigidly High-grade network components Neodymium tweeter magnet structure Low-distortion strontium woofer magnet Speaker grilles KTE-S610G are optional and sold separately Top-mount depth: 2-1/4" Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.