Rockford Fosgate Monoblock Amplifiers (39)

Rockford Fosgate Prime R500X1D 1-Channel Car Prime 500 Watt RMS Class D Car Mono Amplifier + 4G Amp Kit The Prime R500X1D is a 500-watt mono amplifier using efficient Class-D circuit topology. This amplifier is capable of running a 2-Ohm load and includes onboard Punch Bass and remote Punch Level Control. Are you ready for a dedicated subwoofer amplifier for your car or truck? The Prime R500X1D is the perfect companion for any Car Audio Fanatic getting into mobile audio who wants a two-amplifier system: one amp running mids/highs and the second running subwoofers. This class D mono amplifier features variable Punch Bass, variable crossovers, Pass-Thru jacks to daisy chain another amplifier, and a remote Punch Level Control for mounting under the dash or the center console. General Features: Prime Series Class D Monoblock Car Amplifier RMS Power Rating: 4 ohms: 300 watts x 1 channel RMS Power Rating: 2 ohms: 500 watts x 1 channel CEA-2006 compliant amplifier Efficient Class-D circuit topology 12dB/octave Butterworth crossover RCA pass-thru outputs On-board Punch EQ with +18dB boost @ 45Hz. High-level inputs Remote PLC (Punch Level Control) 0°/180° Phase Switch Real-time output and power supply thermal sensing Cast aluminum heatsink 4 Gauge power/ground connectors MOSFET power supply Over-current protection Short circuit protection Muted turn on Frequency Response: 20 - 250 Hz +/- 1 dB Efficiency: 89% @ 4-ohm Total Harmonic Distortion: <1.0% Signal to Noise Ratio: >100 dB Damping Factor: >200 dB Input Sensitivity: 150 mV - 4V Recommended Fuse: 50A x 1 (not included) 8-gauge speaker wire terminals Dimensions: 8.50"L x 6.80"W x 2.00"H Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the box: Rockford Fosgate R500X1D owner's manual Mono subwoofer amplifier Remote Punch Level Control module 18' Remote Punch Level Control cable (RJ-25 connector on both ends) 6" Speaker level input harness 3mm Allen wrench Four 3/4" Self-tapping screws Two 1/2" Self-tapping screws 4 Flat washers Installation & Operation manual (English/ French/ Spanish/ German/ Italian) Amplifier verification certificate ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Rockford Fosgate Prime R500X1D 1-Channel Car Prime 500 Watt RMS Class D Car Mono Amplifier + 4G Amp Kit The Prime R500X1D is a 500-watt mono amplifier using efficient Class-D circuit topology. This amplifier is capable of running a 2-Ohm load and includes onboard Punch Bass and remote Punch Level Control. Are you ready for a dedicated subwoofer amplifier for your car or truck? The Prime R500X1D is the perfect companion for any Car Audio Fanatic getting into mobile audio who wants a two-amplifier system: one amp running mids/highs and the second running subwoofers. This class D mono amplifier features variable Punch Bass, variable crossovers, Pass-Thru jacks to daisy chain another amplifier, and a remote Punch Level Control for mounting under the dash or the center console. General Features: Prime Series Class D Monoblock Car Amplifier RMS Power Rating: 4 ohms: 300 watts x 1 channel RMS Power Rating: 2 ohms: 500 watts x 1 channel CEA-2006 compliant amplifier Efficient Class-D circuit topology 12dB/octave Butterworth crossover RCA pass-thru outputs On-board Punch EQ with +18dB boost @ 45Hz. High-level inputs Remote PLC (Punch Level Control) 0°/180° Phase Switch Real-time output and power supply thermal sensing Cast aluminum heatsink 4 Gauge power/ground connectors MOSFET power supply Over-current protection Short circuit protection Muted turn on Frequency Response: 20 - 250 Hz +/- 1 dB Efficiency: 89% @ 4-ohm Total Harmonic Distortion: <1.0% Signal to Noise Ratio: >100 dB Damping Factor: >200 dB Input Sensitivity: 150 mV - 4V Recommended Fuse: 50A x 1 (not included) 8-gauge speaker wire terminals Dimensions: 8.50"L x 6.80"W x 2.00"H Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the box: Rockford Fosgate R500X1D owner's manual Mono subwoofer amplifier Remote Punch Level Control module 18' Remote Punch Level Control cable (RJ-25 connector on both ends) 6" Speaker level input harness 3mm Allen wrench Four 3/4" Self-tapping screws Two 1/2" Self-tapping screws 4 Flat washers Installation & Operation manual (English/ French/ Spanish/ German/ Italian) Amplifier verification certificate ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Rockford Fosgate Power T750X1bd Compact mono subwoofer amplifier 750 watts RMS x 1 at 1 to 2 ohms Super-compact, bursting with powerRockford Fosgate's Power Series T750X1bd mono amplifier can drive up to 750 watts RMS into a 1-ohm load, allowing you to power multiple subs for bigger and better bass. A dual-fan forced air cooling system keeps this sturdy little amp from overheating, so it can play hard for a long time. Rockford Fosgate's high-tech solutions yield more powerThis Power Series amplifier actively monitors speaker or sub performance using Rockford Fosgate's Constant Power technology. A subwoofer's impedance naturally fluctuates as it performs. So, just like your cruise control increases the engine's RPM to maintain your car's speed uphill, Constant Power maintains this amp's output by increasing its internal voltage and current when the sub's impedance rises. This results in up to a 25% increase in the amp's total power output, especially in the crucial range below 50 Hz where a sub amp really has to shine. Easy to set for optimum performanceRockford Fosgate's C.L.E.A.N. technology (Calibrated Level Eliminates Audible Noise) setup system ensures your music will sound as clean and powerful as possible. It works like this: first download the setup tones from Rockford Fosgate, then play the tone, adjust the receiver volume until a red clip light on the amp goes out, then turn the amp gain up until a blue light comes on. It's that simple — your amplifier will be perfectly set to match your receiver's output. When your receiver reaches maximum clean volume, you'll get maximum clean power from your Power amp. At quiet listening levels, you'll hear less background noise and more of your music. Clip lights monitor distortionIf that blue light turns solid red while you're playing music, the amp's telling you that your source is distorting and you should turn it down, or risk damage to your gear. The optional PLC2 remote level control also doubles as a clip indicator, so you can see from the front seat if your music's clipping and restore pristine sound.Product highlights: mono subwoofer amplifier 500 watts RMS x 1 at 4 ohms (750 watts RMS x 1 at 2 ohms) 750 watts RMS x 1 at 1 ohm CEA-2006 compliant Features: Class BD amplifier technology with Constant Power topology C.L.E.A.N. gain setup system includes clip lights and link to Rockford Fosgate's setup tones differential input circuitry helps eliminate hum dual-fan forced induction cooling variable low-pass filter (50-250 Hz, 12 dB/octave) switchable subsonic filter (28 Hz, 12 dB/octave) variable Punch EQ (0-18 dB at 45 Hz) More Info: preamp and speaker-level inputs signal-sensing turn-on with speaker-level input eliminates need for remote turn-on lead 8-gauge power and ground leads and a 100-amp fuse recommended — wiring and hardware not included with amplifier no onboard fuses — when installing multiple amps in a system, an additional 100-amp in-line fuse between the distribution block and the amplifier is recommended 8-1/2"W x 1-11/16"H x 4-5/16"D warranty: 2 years (extends to 3 years when purchased with a Rockford Fosgate RFK8, RFK8i, or RFK4D amp wiring kit) ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca

Rockford Fosgate T500-1bdCP Power Series mono sub amplifier 500 watts RMS x 1 at 2 ohms Powerful bass performance Rockford Fosgate enjoys a well-deserved reputation for building high-quality mobile audio products. Their Power Series amps sit at the top of the car audio food chain, with proven durability and proprietary technologies that deliver stronger, more reliable performance than most other amps on the planet today. Rockford Fosgate's high-tech solutions yield more power Power Series amplifiers actively monitor their speakers' performance using Rockford Fosgate's Constant Power technology. A speaker's impedance naturally fluctuates as it performs. So, just like your cruise control increases the engine's RPM to maintain your car's speed uphill, Constant Power maintains this amp's output by increasing its internal voltage and current when the speaker's impedance rises. This results in up to a 25% increase in the amp's total power output, especially in the crucial range below 50 Hz where a sub amp really has to shine. Rugged construction, massive bass Rockford Fosgate builds each Power Series mono amplifier with heavy-duty, state-of-the-art components. The award-winning Dynamic Thermal Management design manages the temperature of the internal components, distributing heat evenly for higher efficiency and lower distortion. The unique heat sink allows the heat to escape more readily so the high-power output transistors stay cooler and last longer. A rockin' 500 watts The T500-1bdCP mono sub amp uses an efficient Class bd design to deliver up to 500 watts to your subwoofer system from a remarkably compact chassis. This amp can even drive a 1-ohm load, so you can get massive bass out of a wide variety of system designs. The variable 24/dB per octave crossover creates a more natural-sounding transition from your speakers to your subs. And the 2-year warranty tells you that Rockford Fosgate stands behind this bass bruiser. Product highlights: mono subwoofer amplifier 300 watts RMS x 1 at 4 ohms (500 watts RMS x 1 at 2 ohms) 1-ohm stable (500 watts RMS) CEA-2006 compliant Dynamic Thermal Management cooling system variable low-pass filter (35-250 Hz, 24 dB/octave) selectable subsonic filter (28Hz, 24 dB/octave) variable bass boost (0-18 dB at 45 Hz) optional wired remote bass boost Class-BD amplifier design MOSFET power and output stages preamp-level inputs and outputs 4-gauge power and ground leads and a 100-amp fuse recommended wiring and hardware not included with amplifier no onboard fuses — when installing multiple amps in a system, an additional 100-amp in-line fuse between the distribution block and the amplifier is recommended 11-7/16"W x 2-1/4"H x 8-15/16"D warranty: 2 years ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate T1000-1bdCP Power Series mono sub amplifier 1,000 watts RMS x 1 at 2 ohms Powerful bass performanceRockford Fosgate enjoys a well-deserved reputation for building high-quality mobile audio products. Their Power Series amps sit at the top of the car audio food chain, with proven durability and proprietary technologies that deliver stronger, more reliable performance than most other amps on the planet today.Rockford Fosgate's high-tech solutions yield more power Power Series amplifiers actively monitor their speakers' performance using Rockford Fosgate's Constant Power technology. A speaker's impedance naturally fluctuates as it performs. So, just like your cruise control increases the engine's RPM to maintain your car's speed uphill, Constant Power maintains this amp's output by increasing its internal voltage and current when the speaker's impedance rises. This results in up to a 25% increase in the amp's total power output, especially in the crucial range below 50 Hz where a sub amp really has to shine.Rugged construction, massive bass Rockford Fosgate builds each Power Series mono amplifier with heavy-duty, state-of-the-art components. The award-winning Dynamic Thermal Management design manages the temperature of the internal components, distributing heat evenly for higher efficiency and lower distortion. The unique heat sink allows the heat to escape more readily so the high-power output transistors stay cooler and last longer. The T1000-1bdCP mono sub amp uses an efficient Class bd design to deliver up to 1,000 watts to your subwoofer system from a remarkably compact chassis. This amp can even drive a 1-ohm load, so you can get massive bass out of a wide variety of system designs. The variable 24/dB per octave crossover creates a more natural sounding transition from your speakers to your subs. And the 2-year warranty tells you that Rockford Fosgate stands behind this bass powerhouse. Product highlights: mono subwoofer amplifier 700 watts RMS x 1 at 4 ohms (1,000 watts RMS x 1 at 2 ohms) 1,000 watts RMS x 1 at 1 ohm CEA-2006 compliant Dynamic Thermal Management cooling system variable low-pass filter (35-250 Hz, 24 dB/octave) selectable subsonic filter (28Hz, 24 dB/octave) variable bass boost (0-18 dB at 45 Hz) optional wired remote bass boost Class-BD amplifier design MOSFET power and output stages preamp-level inputs preamp outputs 4-gauge power and ground leads and an 150-amp fuse recommended — wiring and hardware not included with amplifier no onboard fuses — when installing multiple amps in a system, an additional 150-amp in-line fuse between the distribution block and the amplifier is recommended 13-11/16"W x 2-1/4"H x 8-15/16"D warranty: 2 years ⚠️Warning:Cancer and Reproductive Harm-www.P65Warnings.ca.gov

Rockford Fosgate T1500-1bdcp Power Series mono sub amplifier 1,500 watts RMS x 1 at 2 ohms Powerful bass performanceRockford Fosgate enjoys a well-deserved reputation for building high-quality mobile audio products. Their Power Series amps sit at the top of the car audio food chain, with proven durability and proprietary technologies that deliver stronger, more reliable performance than most other amps on the planet today. Rockford Fosgate's high-tech solutions yield more powerPower Series amplifiers actively monitor their speakers' performance using Rockford Fosgate's Constant Power technology. A speaker's impedance naturally fluctuates as it performs. So, just like your cruise control increases the engine's RPM to maintain your car's speed uphill, Constant Power maintains this amp's output by increasing its internal voltage and current when the speaker's impedance rises. This results in up to a 25% increase in the amp's total power output, especially in the crucial range below 50 Hz where a sub amp really has to shine.Rugged construction, massive bass Rockford Fosgate builds each Power Series mono amplifier with heavy-duty, state-of-the-art components. The award-winning Dynamic Thermal Management design manages the temperature of the internal components, distributing heat evenly for higher efficiency and lower distortion. The unique heat sink allows the heat to escape more readily so the high-power output transistors stay cooler and last longer. The T1500-1bdCP mono sub amp uses an efficient Class bd design to deliver up to 1,500 watts to your subwoofer system from a remarkably compact chassis. This amp can even drive a 1-ohm load, so you can get massive bass out of a wide variety of system designs. The variable 24/dB per octave crossover creates a more natural-sounding transition from your speakers to your subs. And the 2-year warranty tells you that Rockford Fosgate stands behind this bass behemoth. Product highlights: mono subwoofer amplifier 1,000 watts RMS x 1 at 4 ohms (1,500 watts RMS x 1 at 2 ohms) 1,500 watts RMS x 1 at 1 ohm CEA-2006 compliant Dynamic Thermal Management cooling system variable low-pass filter (35-250 Hz, 24 dB/octave) selectable subsonic filter (28Hz, 24 dB/octave) variable bass boost (0-18 dB at 45 Hz) optional wired remote bass boost Class-BD amplifier design MOSFET power and output stages preamp-level inputs and outputs 4-gauge power and ground leads and a 200-amp fuse recommended — wiring and hardware not included with amplifier no onboard fuses — when installing multiple amps in a system, an additional 200-amp in-line fuse between the distribution block and the amplifier is recommended 14-15/16"W x 2-1/4"H x 8-15/16"D warranty: 2 years ⚠️Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Punch PBR300X1 Compact mono subwoofer amplifier 300 watts RMS x 1 at 1 ohm You won't believe how small and powerful this amp is. Rockford Fosgate's PBR300X1 mono amp can drive up to 300 watts RMS into a one-ohm load, allowing you to power multiple subs to get more bass. And this Punch Class BR amplifier generates this power from a very tiny case — literally the size of your hand. Boosted Rail (BR) amp technology uses capacitors and high-speed circuitry to boost the amp's power supply voltage, when needed, so it can handle massive musical peaks without missing a beat. Rockford Fosgate uses this new technology to create a remarkable amp that fits almost anywhere and delivers powerful sound. Convenience and reliability Add Rockford Fosgate's famous Punch EQ remote bass boost, and you'll be able to control the subwoofer impact from your front seat. The amp also features speaker-level inputs with signal-sensing turn-on, allowing you to connect into almost any system without having to run a turn-on lead back to the receiver. An extruded aluminum heat sink combines with Rockford Fosgate's heat management technology to make sure your tunes keep rockin' — even when you're playing loud. Product highlights: mono subwoofer amplifier 75 watts RMS x 1 at 4 ohms (150 watts RMS x 1 at 2 ohms) 300 watts RMS x 1 at 1 ohm CEA-2006 compliant suitable for powersports application Boosted Rail amp technology Dynamic Thermal Management cooling system variable low-pass filter (35-250 Hz, 12 dB/octave) differential-balanced inputs eliminate noise from your vehicle's electrical system preamp and speaker-level inputs optional wired remote bass boost (0-18 dB at 45 Hz) 10-gauge power and ground leads and a 30-amp fuse recommended — wiring and hardware not included with amplifier no onboard fuses — when installing multiple amps in a system, an additional 30-amp in-line fuse between the distribution block and the amplifier is recommended 6-15/16"W x 1-9/16"H x 4-5/16"D warranty: 1 year (extends to 2 years when purchased and used with Rockford Fosgate's RFK10 or RFK10i amp wiring kit) ⚠️Warning: Cancer and Reproductive Harm-www.P65Warnings.ca.gov